M200 Bluescreen when undocking

Hi!
Lately I cannot safely undock my M200 from the Port replicator. Everytime I try, the result is a bluescreen "Multiple IRP Requests" and the system reboots. This has only been happening for the last two weeks.
I did reinstall the Toshiba Mobile Tools, just to make sure that support for docking is enabled, but this did not help. Is there anyone who faced the same problem and solved it? I want to avoid reinstalling the complete system if possible.
Yours,
Thies

Thank you very much for your help. In the meantime I think I was able to find the cause of the problem. When I uninstalled a software for experiment design, the failures stopped to happen. I was not aware, that a Java based software could have this effects. May be it was not the main application, but a software licence system they used, but I am not sure...

Similar Messages

T400 BSOD when undocking

I have two T400's that BSOD when undocked from an Advanced Mini Dock. They also BSOD when the user changes display settings. They both use a secondary external monitor. We have tried Windows (XP SP3)Display settings, Hardware Profile settings, ThinkVantage Display/Presentation setting, but still get BSOD.
Any help? Info? Suggestions?
Solved!
Go to Solution.

Thanks Caf.
We performed System Update and got the latest/greatest drivers but still no go. It bluescreens a second or two after physically undocking (or changing a display setting). The error message is roughly: blah, blah, disk space, blah, blah, BIOS, blah, blah, win32k.sys Performing physical memory dump. Then it reboots.
We get the same error on both systems.
Note: They do NOT bluescreen if we disconnect the second monitor (just to make things more interesting).

Lenovo Ideapad S12 Bluescreen when watching Video

I get a bluescreen when I start watching a video. Yesterday it worked and today there is the bluescreen.

while watching flash videos?
if so, disable "hardware acceleration" in flash options

X120e bluescreen when installing lan drivers

I am getting a bluescreen when I try to install the lan drivers posted on the support site for x120e. For now I just have the device disabled because I can just use wireless, but would like to get this resolved.
I am using win 7 x64 and have upgraded to 8gb of ram.
Here is the info from windbg:
PAGE_FAULT_IN_NONPAGED_AREA (50)
Invalid system memory was referenced. This cannot be protected by try-except,
it must be protected by a Probe. Typically the address is just plain bad or it
is pointing at freed memory.
Arguments:
Arg1: fffff6fc40041000, memory referenced.
Arg2: 0000000000000001, value 0 = read operation, 1 = write operation.
Arg3: fffff80003432ca3, If non-zero, the instruction address which referenced the bad memory
   address.
Arg4: 0000000000000009, (reserved)
Debugging Details:
Page e1 not present in the dump file. Type ".hh dbgerr004" for details
OVERLAPPED_MODULE: Address regions for 'ndisuio' and 'RtsUStor.sys' overlap
WRITE_ADDRESS: fffff6fc40041000
FAULTING_IP:
nt!MmMapIoSpace+413
fffff800`03432ca3 498901          mov     qword ptr [r9],rax
MM_INTERNAL_CODE: 9
DEFAULT_BUCKET_ID: VISTA_DRIVER_FAULT
BUGCHECK_STR: 0x50
PROCESS_NAME: System
CURRENT_IRQL: 0
TRAP_FRAME: fffff88002fc4c60 -- (.trap 0xfffff88002fc4c60)
NOTE: The trap frame does not contain all registers.
Some register values may be zeroed or incorrect.
rax=000000000020096b rbx=0000000000000000 rcx=0000fffffffff000
rdx=0000000000000000 rsi=0000000000000000 rdi=0000000000000000
rip=fffff80003432ca3 rsp=fffff88002fc4df0 rbp=0000000000001000
r8=0000000000000200 r9=fffff6fc40041000 r10=000000000000096b
r11=0000000000000000 r12=0000000000000000 r13=0000000000000000
r14=0000000000000000 r15=0000000000000000
iopl=0         nv up ei ng nz ac po nc
nt!MmMapIoSpace+0x413:
fffff800`03432ca3 498901          mov     qword ptr [r9],rax ds:4d88:1000=????????????????
Resetting default scope
LAST_CONTROL_TRANSFER: from fffff80003509c31 to fffff80003489740
STACK_TEXT:
fffff880`02fc4af8 fffff800`03509c31 : 00000000`00000050 fffff6fc`40041000 00000000`00000001 fffff880`02fc4c60 : nt!KeBugCheckEx
fffff880`02fc4b00 fffff800`0348782e : 00000000`00000001 00000000`00000001 00000014`00000000 00000000`00000000 : nt! ?? ::FNODOBFM::`string'+0x424f9
fffff880`02fc4c60 fffff800`03432ca3 : 00000000`00000001 00000000`00000001 00000000`00000001 fffff880`00000000 : nt!KiPageFault+0x16e
fffff880`02fc4df0 fffff880`080e11b7 : 00000000`00000000 00000000`00000000 00000000`00007cb1 fffff6fc`40041000 : nt!MmMapIoSpace+0x413
fffff880`02fc4f20 00000000`00000000 : 00000000`00000000 00000000`00007cb1 fffff6fc`40041000 fffffa80`08432530 : Rt64win7+0x4f1b7
STACK_COMMAND: kb
FOLLOWUP_IP:
Rt64win7+4f1b7
Page e1 not present in the dump file. Type ".hh dbgerr004" for details
Page e1 not present in the dump file. Type ".hh dbgerr004" for details
fffff880`080e11b7 ??              ???
SYMBOL_STACK_INDEX: 4
SYMBOL_NAME: Rt64win7+4f1b7
FOLLOWUP_NAME: MachineOwner
MODULE_NAME: Rt64win7
IMAGE_NAME: Rt64win7.sys
DEBUG_FLR_IMAGE_TIMESTAMP: 0
FAILURE_BUCKET_ID: X64_0x50_Rt64win7+4f1b7
BUCKET_ID: X64_0x50_Rt64win7+4f1b7
Followup: MachineOwner
Solved!
Go to Solution.

pinkthad wrote:
goretsky wrote:
Hello,
If you replace your original memory are you then able to install the network drivers without error?
Regards,
Aryeh Goretsky
Hi Aryeh,
Thanks for the suggestion, but switching back to the original 2GB does not appear to make a difference. I am however able to use a generic driver provided by windows after the following steps:
1. Installed the lenovo driver and it bluescreened.
2. After rebooting, installed the lenovo driver again, didn't bluescreen this time but in device manager it shows that the driver failed to load (error code 31).
3. Uninstall the lenovo driver.
4. Reboot and the generic windows driver gets installed.
To add a little more information, I was attempting to install the driver (7.26.902.2010) located at http://www-307.ibm.com/pc/support/site.wss/MIGR-76363.html
Anyone else having this issue?
I had the same problem with the Lenovo network driver -- I just installed the driver from Realtek instead: http://www.realtek.com.tw/downloads/downloadsView.aspx?Langid=1&PNid=13&PFid=5&Level=5&Conn=4&DownTy...

Vista loses IP config when undocking

I used to use ThinkVantage's Access Connections to manage my network connection profiles on my Thinkpad. I just recently uninstalled it because I decided to just rely on the Vista has natively.
Since our office requires static IP, I set that up at the LAN properties. Everything works fine when I start from a clean boot. It's when I undock and redock to the docking station that problem starts. I lose the static IP configuration. Instead Vista assigns:
IP: 169.254.77.37 (supposed to be 10.11.2.xxx)
Subnet: 255.255.0.0 (supposed to be 255.255.254.0)
Gateway: blank
DNS: correct
I now find myself having to do a reboot everytime I just need to undock and go to a 30 minute meeting when I used to be able to undock and redock without any problems whatsoever.
Why does Vista assign this random IP when it is hard configured?
How can I solve this problem?
Thanks.

I have not been doing images or restores (although seriously considering it. thanks) because I could usually troubleshoot once I understand what's happening.
This time I really don't understand how a static IP assigned can get lost when undocking/redocking. It boggles me and I am lost. Too late for me to do a restore.
I have a temporary solution which is to set another IP address and when the problem appears I simply switch to the other one. It's a not a beautiful solution and I had to bribe our LAN admin to give me the extra IP but that's what I got now.
I am still searching for this annoying yet challenging problem. I hope it also challenges people in this forum.
NPendrigh wrote:
I image my C drive before doing any OS or Program installations or removals so that I can trivially in about 15 minutes restore to a known good system (my data has previously been moved to another partition) using Acronis True Image Echo Workstation
Do you have a back up of a known good system?
If so restore from that. If not, you may be lucky enough to just uninstall and re-install the network driver software or swap the network adapter. Else, it would appear to be either live with what you have or
- selectively reinstall/repair the OS and everything either with the installation CD's or using Rescue & Recovery
- or format the disk and start again
While philosophically, I used to remove as many apparently surplus programs as possible, now I do not bother because in the past I have wasted far to much time being "right" instead of just using the system as a tool to Get Things Done!
Good Luck
Nigel

X61 Standby issue with XP when undocked

Hi,
Just did a HDD upgrade on my most excellent X61 and after a clean install of XP, I now have an issue with the Standby functionality. Here's the symptoms:
1. If I restart while X61 is docked, I get normal startup and standby mode works both when docked and after proper undocking procedure. Works as expected.
2. If I restart undocked, the Standby option in the "Turn Off Computer..." menu is grayed out and sure enough, never goes into standby. I have of course tried to modify power options in the Control panel, but it never gives me the option to go into Standby mode when lid is closed.
I do have dual boot on my X61 with Debian Linux and that supports Standby, no issues.
So, after some background reading, seems there is a possibility that I missed a driver during installation and some HW is not letting the X61 enter standby when it is not docked.
Any ideas which driver this may be??? Though I'd ask before having to through and try to install ALL drivers again
thanks in advance for any input...
Jeff

Just tried installing lots of stuff I probably don;t need with System Updater. Now I've got:
- Still no standby when undocked
- 2 instances of thinkvantage toolbox that does nothing but try to repair "installed fonts" and fails
- ThinkPad Video Features (Intel GM965) keeps recurring in the updates. When I try, it says successfully installed, but ???
Any ideas?
thanks

Spotify closes when undocking laptop

For some reason, when I physically eject my laptop from its docking station (like, if I want to move my laptop from my desk to another location) Spotify closes itself. It doesn't seem to matter if I have my music playing or not, although I generally have it paused at that point the vast majority of the time. I can restart Spotify just fine afterwards. I am using Windows 7 Professional, and I have a Dell-brand laptop and docking station.
Has this happened to anyone else? If so, did you figure out a way to keep it from happening? It's not a huge deal by any means, but it is a little weird.

I haven't ever received an official response, and it still does it for me occasionally (not every single time, though) regardless of which Spotify version I have, since I generally update when prompted. Like others have said, it also defaults to some pretty old tracks when I reopen it... like, something that I had listened to the week prior, which can be a pain sometimes. One thing that seems to maybe help a little is if I do not pause my music when undocking my laptop. I work in a pretty casual office, though, and I listen to very calm (and quiet!) music, so this is definitely not a solution for everyone.

Bluescreen when trying a clean install from CD - X61

Hey,
I got a question from a neighbour if I could help him reinstall his laptop. It's a X61.
He got it from his employer when they decided to buy a bunch of new laptops for the company. Therefore he has no backup discs, no system reset software or anything. It's just the laptop and the power supply. He used the laptop 'as is' for a while but now it needs cleaning. He asked the IT department on his job but they didnt save any discs or software for the laptops. There is a Restore and Resque partition on the HDD which is accessible via the Thinkvantage button at boot, but no software in that console is working.
So he went out and bought a Windows XP license to make a clean install on the PC but we are having difficulties to make it run...
I tried to format an USB stick to install Windows XP from. After boot I only get a blank screen with a flashing marker...
I tried an external DVD-drive since the PC doesnt have any and I get the installations program to run. It starts to load the files but after a short while I get a bluescreen...
I'm running out of options here, any suggestions?

echX, welcome to the forum,
a solution that works for a lot of people is to set the SATA to compatability mode in BIOS; press F1 at boot > Config > SATA. After XP has been installed you can install the necessary driver and switch it back to AHCI.
Andy ______________________________________
Please remember to come back and mark the post that you feel solved your question as the solution, it earns the member + points
Did you find a post helpfull? You can thank the member by clicking on the star to the left awarding them Kudos Please add your type, model number and OS to your signature, it helps to help you. Forum Search Option T430 2347-G7U W8 x64, Yoga 10 HD+, Tablet 1838-2BG, T61p 6460-67G W7 x64, T43p 2668-G2G XP, T23 2647-9LG XP, plus a few more. FYI Unsolicited Personal Messages will be ignored.
Deutsche Community Comunidad en Español English Community Русскоязычное Сообщество
PepperonI blog

XFCE workaround: Laptop wallpaper not kept when undocked

So I've been running into the minor annoyance of XFCE always using the wallpaper from the monitor on the left screen after I unplug my secondary monitor. Not sure if anyone else runs into this. Just to clarify:
(pretend the pipe is the border between screens)
While docked: Wallpaper A (VGA-1) | Wallpaper B (LVDS)
Undocked: Wallpaper A (LVDS)
I would expect wallpaper B to persist on the laptop display regardless of whether the second monitor is hooked up or not.
Since I use a script to toggle my monitor off and on using a hotkey I made a few modifications to it so that you can specify the wallpaper setup while docked or undocked. You could also have completely different wallpapers while mobile if you don't want to be seen in public with your My Little Pony wallpaper.
(I still use a CRT as a second monitor, don't make fun of me)
#!/bin/bash
#Absolute path seems to be required for some reason.
location="/home/jason/.config/xfce4"
function xfset {
cat $location/$1 | while read line; do
variable=`echo $line |awk '{print $1}'`
setting=`echo $line |awk '{print $2}'`
xfconf-query -c xfce4-desktop -p $variable --create -s $setting
done
current=`xrandr |grep current |awk '{print $8 $10}'`
if [ $current == '1366768,' ]
then
#Going to Dual
xfconf-query -c xfce4-desktop -l -v|grep backdrop>$location/single.set
xrandr --output LVDS --mode 1366x768 --pos 1600x432 --rotate normal --output CRT1 --mode 1600x1200 --pos 0x0 --rotate normal --output DFP1 --off;
xfset dual.set
else
#going to single
xfconf-query -c xfce4-desktop -l -v|grep backdrop>$location/dual.set
xrandr --output LVDS --mode 1366x768 --rotate normal --output CRT1 --off --output DFP1 --off
xfce4-panel -r
xfset single.set
fi
Let me know if you have any feedback or found this useful. I'm curious if this is a problem anyone else has.
Last edited by Jasonvw (2013-02-21 09:51:36)

You could look at xfconf properties comparing both monitors with one montor connected to find out differences.
i.e. xfconf-query -c xfce4-desktop -l
Setting a wallpaper in xfce through xfconf:
xfconf-query -c xfce4-desktop -p /backdrop/screen0/monitor0/image-path --create -t string -s $wp
xfconf-query -c xfce4-desktop -p /backdrop/screen0/monitor0/image-show --create -t bool -s true
xfconf-query -c xfce4-desktop -p /backdrop/screen0/monitor0/image-style --create -t int -s 0
Where $wp is set to full path of image file.
When comparing the properties you might find monitor1 becomes monitor0 and that might explain the wallpaper switching.
You can find out the path to the current wallpaper using a query like:
xfconf-query -c xfce4-desktop -p /backdrop/screen0/monitor0/image-path
May be some of the above will help you figure something out. I only mention it because it is disconcerting to me that you are killing stuff like xfconfd and xfdesktop to achieve the proper wallpapers.

How to keep Ipod in iTunes when undocked

I want to be able to see and manage my ipod music while it is undocked. I did this before, but for the life of me, can't figure out how to keep the iPod showing in iTunes when it's undocked. Any help would be appreciated. Thanks!
Randy
Dell Windows XP

If it's not connected to the computer, you can't do anything with the iPod.
You can Enable disk use in iTunes prefs -> iPod and it will not dismount.
I want to be able to see and manage my ipod music while it is undocked.
That is what iTunes is for.
Make the changes in iTunes and then update the iPod.
Any changes you make on the iPod will not be reflected in iTunes.
When you have to Restore the iPod (you will), all changes will be lost.

Disable 2nd monitor when undocking?

I posted this before but nobody replied so maybe I need to simplify it.
When I hit the eject button on my ThinkPad dock it turns off everything on the dock (including USB) except for DVI, which then causes Windows 7 to set both monitors to Duplicate at 1024x768. I just want it to disable the DVI monitor and go back to laptop monitor instead.
Is there a way to do this? I don't know why it keeps the DVI monitor going when the dock is ejected. Thanks.

Can somebody familiar with the dock please reply to this?
Hint: use Win+P to view monitor configurations.
When I press the undock button, it switches to Duplicate and both monitors (one DVI) show 1024x768 (even though all USB connections disconnect).

Bluescreen when deploying AMD Windows 7

Hi,
When capturing an image on an AMD system with Windows 7, I'm getting bluescreens after deployment.
For capturing an image I enter Audit Mode by CTRL-SHFT-F3. I tested it with all the Windows Updates and without even doing a single thing in Audit Mode (chose for generalize and system shutdown in sysprep right away). Capturing goes al fine, but on any AMD
system where I want to deploy it on I'm getting this blue screen which closes to fast to see what causes this. Strange enough deploying windows 8 AMD goes all fine. Also I've got a lot of drivers for AMD injected in the install and caputere image.
When entering safe mode, getting a bluescreen after amdkmafd.sys.
Does anyone have a solution for this problem?
Kind Regards,
Bas

Hi Bas,
From the file name amdkmafd.sys, I think we can test to remove injected drivers from the image and do the deployment. Then let's install drivers for devices to see if anyone causes the issue.
Also update your firmware may also help on this situation. However update firmware may cause hardware issue you could confirm with device manufacturer first.
In addition, Setupapi.dev.log (%windir%\inf) will log information for hardware driver. You could also check this file to see if there is any error during driver installation.
If you have any feedback on our support, please send to [email protected]

X201 wireless shuts off when undocking

My x201 laptop wireless shuts of when I undock and I have to re-enable it in network properties everytime. I thought I fixed it in the power managment settings but I must have missed it. Any help would be great.
Thanks

hey sstockham,
I would recommend updating the following
bios
firmware
wireless network drive
http://www-307.ibm.com/pc/support/site.wss/MIGR-70656.html
WW Social Media
Important Note: If you need help, post your question in the forum, and include your system type, model number and OS. Do not post your serial number.
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"!
Follow @LenovoForums on Twitter!
Have you checked out the Community Knowledgebase yet?!
How to send a private message? --> Check out this article.

Outlook 2010 sticks on "Trying to Connect" when undock Laptops and VPN Connects Automatically

When our users undock their laptops the VPN kicks in automatically. All of the other network services just continue seamlessly. Outlook, however, sticks at "trying to connect". This is often accompanied by a password prompt.
This is easily solved by closing Outlook and reopening it (no need to enter password).
It doesn't seem unreasonable that outlook should require a restart after being disconnected like this. Just want to establish whether there is a way to have Outlook just re-connect without the need to close it and reopen it. Or is the need to
restart it unavoidable?
Thanks.

When our users undock their laptops the VPN kicks in automatically. All of the other network services just continue seamlessly. Outlook, however, sticks at "trying to connect". This is often accompanied by a password prompt.
This is easily solved by closing Outlook and reopening it (no need to enter password).
It doesn't seem unreasonable that outlook should require a restart after being disconnected like this. Just want to establish whether there is a way to have Outlook just re-connect without the need to close it and reopen it. Or is the need to
restart it unavoidable?
Thanks.
This is really a question for the Outlook forum, but from what I have seen over the years, thats just the way it is with OUtlook and MAPI or Outlook Anywhere. When you change the network, Outlook struggles..
Having said that, MAPI over HTTP with Exchange 2013 SP1 is working to eliminate those issues:
http://technet.microsoft.com/en-us/library/dn635177(v=exchg.150).aspx
Twitter!: Please Note: My Posts are provided “AS IS” without warranty of any kind, either expressed or implied.

Bluescreen when installing DR4-A

Does ANYBODY know why my win xp bluescreens after I update the firmware in my dr4-a? I had the same problem installing it into the computer after I bought the blippin' dr4 too, I don't know just how I managed to get it installed but I was very close to taking it back to the store after the 30th bluescreen..
So, I've got it working with f/w 2.30 but with 2.50 it's the same thing all over again: windows keeps freaking out and rebooting when it's trying to discover the "new" hardware and continues to do so no matter what I do..
If I downgrade it back to 2.30 it works again but that's just stupid.
sys:
cpu: amd xp 2200+
agp: msi gf 4200ti
dvd: msi dr4-a
mb: albatron km18gpro
hd: couple of hd that work just fine
os: win xp pro, sp1
Hope someone knows something. I've got a MSc in computer engineering and I'm stumped...
/payer

Hey, thanks for your input. However, my psu is quite sufficient. As I said: the drive works with f/w 2.30. Any other thoughts?

M200 Bluescreen when undocking

Similar Messages

Maybe you are looking for