M45-S165 with new Hard Drive will not reformat and recover.

I replaced the crashed Hitachi 80GB hard drive with a new WD 320 GB WD3200BEVE. I have the Toshiba Recovery and Applications / Drivers DVD Satellite M40/M45 Series CD, media number TK143/PMAE00300010. I start the computer, insert the disc and shut it down and wait a minute. When I restart the computer and press the F12 key when I see the Toshiba screen and I select boot from CD Drive and press enter. Then the screen goes black and "Starting Windows 98" shows up with other copy. Next I get "Welcome to the Toshiba Recovery Utility" and press F1 for OK to accept license agreement. Next I get "Recovery in process" briefly then the WARNING screen for erasing hard drive and press "C" for continue. Next "Toshiba" screen comes up again then "starting windows 98" again, then "Welcome to recovery utility" again. I press F1 then "C" and it starts all over again. What am I missing?

Hi, hjbugs, and welcome to Apple Discussions. Disconnecting the drive while your Powerbook was accessing it probably caused your problem. It may be repairable using DiskWarrior or TechTool Pro, but if you don't have access to one of those and aren't going to buy one, reformatting the drive with Disk Utility may be the only other way to make it usable again. If it contains data you need to recover first (i.e., data that isn't also stored on your internal HD or other storage media), download the free demo version of one of the data recovery utilities mentioned in this thread and use it to see what is recoverable. If the files you need are recoverable, buy the full version of one of the utilities and recover them.

Similar Messages

Problems with External Hard drive, will not mount and errors in disk utilit

i have a powerbook g4 aluminum. i have an external hard drive for it. a simple tech 100gig portable drive, almost brand new. i dont know what happened to it, but one day i was starting my computer up with it attached. it wounldnt fully start up, said "waiting for local disks" so i uplugged the external hard drive. now it wont mount and will only show up in the disk utility of my friends macbook. i tried to verify and repair, and this is the message i got.
Verify and Repair disk “UNTITLED”
** /dev/disk1s1
could not read boot block (Input/output error)
Error: The underlying task reported failure on exit
1 non HFS volume checked
1 volume could not be repaired because of an error
Im in mexico writing a book and so i really need help on this one guys.

Hi, hjbugs, and welcome to Apple Discussions. Disconnecting the drive while your Powerbook was accessing it probably caused your problem. It may be repairable using DiskWarrior or TechTool Pro, but if you don't have access to one of those and aren't going to buy one, reformatting the drive with Disk Utility may be the only other way to make it usable again. If it contains data you need to recover first (i.e., data that isn't also stored on your internal HD or other storage media), download the free demo version of one of the data recovery utilities mentioned in this thread and use it to see what is recoverable. If the files you need are recoverable, buy the full version of one of the utilities and recover them.

My external hard drive will not open and only shows up in Disk Utilities. When I try yo repair it, it give me and error of invalid sibling link. How do I fix my external hard drive?

My external hard drive will not open and only shows up in Disk Utilities. When I try yo repair it, it give me and error of invalid sibling link. How do I fix my external hard drive?

Invalid sibling link may not be fixable by Disk Utility. (Disk Utility is very conservative, and will not attempt repairs that might cause you to lose data.)
It is an indication of serious Directory damage.
that leaves
a) third-party Utilities that will take those risks, or
b) re-initializing the drive (which deletes all your data) and restoring from another backup source.
c) "Copying off whatever files you can salvage" has gone by, and you cannot copy anything off a drive that will not mount. You may be able to use "rescue" programs such as prosoft engineering Data Rescue to copy files to another drive, but that sounds a lot better than its reality. You may get many files, but not get ANY filenames.

T61 New hard drive will not boot, BIOS doesn't reckognize.....

Ok i need some major help here. I recieved a new Seagate 500Gig internal hard drive for my lappy. so i thought i would do a fresh install of windows vista, via the restore media that i created from the thinkvantage software on my laptop.
Now here is where the problem lies....Before I install it, format it or write any data to it, BIOS reads the new drive just fine. As soon as i run the recovery software cds i get a verry anoying error.
The following is the exact error message.
"error 2100: HDD0 Initialization error (1)"
Has anyone else seen this and been able to install a new hardrive in this laptop?
Weird thing is this. I put the old HD back in 100GIG and connect the new one, that BIOS won't read after data has been written to it, to an external USB case.
I load windows vista just fine off my old drive, plug in the now 500G external drive and windows reads the data that has been written to it from the restore CDs.
Can anyone help me out here. I have spent the past 2 full days trying to figure this out.
Thanks

Ok just as an update thus far. i still can't get it to read the hd after i install from the recovery discs...which is odd of course.
It does read the drive before i install anything to it though.
OK time to add something really really weird though, i an attempt to figure this out, i installed the 500G drive and put ubuntu on it just to see if the problem was w/ the HD having a failure or not.
ubuntu installed just fine, and i am typing this off the installed ubuntu OS.
SO now i have to ask, is there a bug in the recovery cds that thinkvantage has us create? is there a way to test that?
Does the t61 have a limitation w/ a 500GIG hard drive that will not let the recovery dvds work or install properly?

New hard drive will not recover from disks cq62 notebook

I made the recovery disks when the laptop was purchased (compaq cq62-423nr).
I recently had a hard drive fail and purchased a seagate 500 GB 5400 drive to replace the 320 gb 5400 drive
ran the recovery disks twice as minimal and also complet factory reset. all 3 times the recovery process went through the 4th disk to completion and at restart no bootable disk found.
ran bios diagnostics and recovery disk diag too. everything passed.It also has the current BIOS rev.
Would put Linux on if it wasnt the wife's. Any help getting me out of the dog house is appriciated.
This question was solved.
View Solution.

Hi there
Your specs: http://h10025.www1.hp.com/ewfrf/wc/document?docname=c02800846&tmp_task=prodinfoCategory&cc=in&dlc=en...
I'm thinking the recovery discs is bad or corrupted.
If you like, order recovery media directly from HP:
https://h10025.www1.hp.com/ewfrf/wc/mediaOrder?softwareitem=630259-001&cc=us&dlc=en&lc=en&os=4063&pr...
Alternatively you can make bootable USB with Windows 7 Home Premium 64-bit ISO & do a clean install:
http://msft.digitalrivercontent.net/win/X17-58997.iso
Windows 7 Home Premium x64 English
Size: 3,243,070KB, MD5 hash: da319b5826162829c436306bebea7f0f
Note: THIS METHOD CAN ONLY WORK IF YOU CAN CLEARLY & LEGIBLY READ 25 CHARACTERS OF PRODUCT ACTIVATION KEY PRINTED IN COA STICKER ON THE BACK OF THE LAPTOP.
Download, save latest versions of additional drivers & copy it to another USB and install it later on after Windows installation:
http://h10025.www1.hp.com/ewfrf/wc/softwareCategory?os=4063&lc=en&cc=us&dlc=en&sw_lang=&product=5101...
CLEAN INSTALL tutorial:
http://www.sevenforums.com/tutorials/219487-clean-reinstall-factory-oem-windows-7-a.html
Regards
Visruth
++Please click KUDOS / White thumb to say thanks
++Please click ACCEPT AS SOLUTION to help others, find this solution faster
**I'm a Volunteer, I do not work for HP**

New Hard drive will not boot

Today i installed a new 1Tb segate HD in my mid 2010 MBP. After a long painful waiting game of backing up to time machine i swaped the harddrives,and reinstalled OSX Snow Leppard. After importing all my time machine data i attempted to log in. I was dennied access on both accounts on the computer. I tried a restart and now my mbp is hanging in the blue screen.
FYI my time machine backup was created of mountin lion.

To move the files manually, erase the drive and install Snow Leopard as usual. Then, follow the Setup Assistant steps and, when you arrive to Desktop, open Finder, go to your external drive > Backups.backupdb > yourmac > Latest > Users > user and copy the files to your internal disk. For example, if you want to copy the data that is in Pictures folder, you would want to copy it to Pictures folder in your internal drive

Recovery discs do not work with new hard drive

Hi I have come here desperately seeking help as I am not too knowledgeable with the workings of computers and I have spent an incredible amount of time just trying to get my laptop to some level of functionality. I purchased a HP Envy and it had a corrupt hard drive which would not work from day one, laptop was new. After a year of constant pressure on HP they finally decided to replace it and let me choose any laptop so I went with the Beats Envy 14 as it was the best one offered from the selection. Low and behold the thing would not work properly from day one, again my brother who is much more of an expert said that there was definitely a hard drive issue so for the past 3 years I have put up with a computer that constantly crashes with BSOD, where I have lost data on numerous occasions (only so often I can back up), that I have had to constantly reset the thing using HP recovery discs, and that generally cannot cope when performing multiple tasks. HP are most certainly shocking builds from my experience. Then just last week the hard drive just craps itself and the laptop no longer will boot up. I took it to a guy to get it at leYst working again so he has installed a new hard drive but with an old version of Windows 7. I want to go back to the Windows version I was akin to on the HP recovery disk , and essentially have it all set up as before except for now having a workable hard drive however I get the message: "This computer is not supported by the System Recovery Discs.You will not be able to continue to recover this system with these discs.Error: 0100 - 3385 - 3078" I also tried out of interest to load my old Windows 7 disc I had and XP but had no success. Tried booting from startup etc and various things suggested on help forums. Please tell me I am not stuck with this version of windows. Whilst the discs included Windows 7 it was a totally different version, this home premium one is terrible. Any help/advice would be gratefully received. Thanks

no they were both 500gb. I read about that already, I heard about creating a partition for recovery etc but this is all a bit above me , as I said I am not very technical when it comes to the working of a computer. These discs worked perfectly before but now with the new hard drive will not load at all. I essentially hate the Windows Home Premium verions the guy who fixed it put on, whilst the discs had Windows 7 on them the icons were way smaller, the desktop neater, the buttons different, everything was a lot more modern and I was used to it. This version looks like something from the 90s, have to constantly adjust size of Mozilla when browsing as it is huge. I have my own version of Windows 7 on another disc but the hard drive will not let it load either........considering waiting for Windows 10 but again unsure if this new hard drive will even let that update Thanks

MacBook Pro won't boot with new hard drive, but a different MacBook Pro will

So here are the details. My friend and I both have 13-inch Mid 2010 MacBook Pro's. Same processor and specs since they were purchased at the same time, but originally had 250 GB hard drives. His hard drive failed and needed a new one. Put a 500 GB Seagate Momentus 5400.6 in his computer, and tried using a flash drive with "Install OS X Mavericks" on it to install Mavericks on his new hard drive. No matter what, it wouldn't install. I finally was able to install OS X 10.9.4 on it by connecting the new hard drive to my computer with a USB hard drive enclosure. I put the hard drive back inside his computer and it wouldn't boot (stuck on the gray screen with apple logo and a spinning wheel). I then attached to the hard drive to his computer externally with the USB enclosure, and then it booted and worked perfectly.
So, it seemed like the problem was with something inside his computer, but then I switched our drives, and that doesn't seem to be the case anymore. I put my original hard drive into his computer, and his new hard drive into my computer, and they both booted and worked perfectly, so I have no idea why his computer will not boot with the new hard drive internally.
To summarize, his computer boots with: 1) new hard drive connected externally (won't work if it's internal), and 2) my hard drive internally
but my computer boots with: 1) new hard drive connected externally AND internally, and 2) my hard drive internally.
Both hard drives have OS X 10.9.4 installed
If anyone has any idea what's causing this and how to make his computer work with the new hard drive internally that would be greatly appreciated.

So after switching the internal SATA cables from each computer, now we have
His computer, with my SATA cable:
1) Worked with every hard drive!
My computer, with his SATA cable:
1) Works with 1 TB Toshiba hard drive
2) Works with 500 GB Seagate hard drive
3) Works with my original hard drive
4) Flashing folder with question mark with his old hard drive
So it turns out you were right! Definitely had something to do with the SATA cables. But it's still strange that mine was able to boot with all the hard drives except the one that was originally in his. So it seems like it was some combination of his SATA cable and something else, since when his SATA cable was in his computer only 1 hard drive (my original) worked, and when it was in my computer, 3 hard drives worked. But at least its working, and I'm just gonna keep our SATA cables switched since that seems to work out fine

Will Time Machine with Leopard Sync With New Hard Drive and Snow Leopard?

My computer is a 20" iMac that I bought in late 2008. The hard drive had trouble so Apple repaired with disk utility. Week later, more trouble so they did full hard drive erase. Data was backed up on Time Machine, 500GB also bought in 2008. After full hard drive erase, and reinstall of basic software, upon reboot, computer would power on then immediately off. It doesn't get past white screen. They advised a new hard drive install is needed.
A computer friend can install a hard drive just fine for me. However, I do not have the Leopard install disc. He could do it with Snow Leopard but I am scared. I'm afraid because my Time Machine last backup was with Leopard, not snow Leopard. I do not have my application discs with me, they are in storage in another state. Thus, if upon adding replacing hard drive and installing Snow Leopard my computer won't be able to sync FILES and APPLICATIONS from Time Machine because its on Leopard I will have a problem.
How can I either 1)Get a Leopard install disc and do that with the new hard drive install OR 2)make sure that a Snow Leopard install with new hard drive won't prevent my Time Machine from being able to install the saved FILES and APPLICATIONS if I don't have original APPLICATION (ie Aperture, Photoshop) with me? Thanks for any help you can provide.

thetrudz wrote:
A computer friend can install a hard drive just fine for me. However, I do not have the Leopard install disc.
Hi, and welcome to the forums.
That Mac should have come with Leopard. If so, call AppleCare. They'll send you replacement discs for a nominal fee.
Once this is sorted out, make a 8-10 GB partition on an external HD or your internal HD, and use the Restore tab of Disk Utility to copy the Install disc to that partition. Then you can boot and run from it instead of the physical disc. It will boot and run much faster, too.
He could do it with Snow Leopard but I am scared.
If he does, and doesn't provide a retail Snow Leopard disc, you must buy one ($29). It's a violation of the license to share software, and you'll need a SL disc to do things like restore a Snow Leopard backup, or the Snow Leopard Apple apps, or repair the internal HD.
Your best bet is to stay with Leopard, at least until you have access to your 3rd-party software discs.
What you can do, however, is borrow his Snow Leopard Install disc (assuming it's a white Retail disc, not a gray one that came with his Mac), and use it to do a full system restore from your backups. That's not a violation of the license, since you don't install or use OSX from that disc; you just use the Installer utility on it to restore the Leopard OSX and all your data from your backups.
See #14 in [Time Machine - Frequently Asked Questions|http://web.me.com/pondini/Time_Machine/FAQ.html] (or use the link in *User Tips* at the top of the +Time Machine+ forum), for details.

I recently updated my Mid 2007 iMac with the latest OS 10.8.5 now my external hard drives will not show up. They show up when I boot them up on a machine running and earlier OS. Is there a fix for this?

I recently updated my 20-inch, Mid 2007 iMac with the latest OS 10.8.5 now my external hard drives will not show up. They show up when I boot them up on a machine running and earlier OS. Is there a fix for this?

Can you see them in Disk Utility?
If so, can you select and Mount them?
If not, disconnect them, reset the iMac's SMC and then reconnect them.
Intel-based Macs: Resetting the System Management Controller (SMC)
1. Shut down the computer.
2. Unplug the computer's power cord.
3. Wait fifteen seconds.
4. Attach the computer's power cord.
5. Wait five seconds, then press the power button to turn on the computer.
If you still can not see them, connect them back up to the iMac running the older OS, open Disk Utility and look to see how they are partitioned and formatted.

New hard drive is not recognized by my MacBook Pro.

New hard drive is not recognized by my MacBook Pro. The supplier says I need to update my BIOS. True? How do I do that?
Hard drive: NN2-72-500-SSE Seagate Momentus 7200.4 (ST9500423AS) 500GB Laptop Hard Drive
Mac OS: Mac OS X Lion 10.7.5

I went through a similar issue with a Seagate Momentus 750GB HDD/8GB SSD with my late-2011 MBP. No matter what I tried, the machine would not recognize the drive.
To test it, I installed the drive in an old ThinkPad, and it worked fine. Then I tried installing it in my PS3, and the drive worked fine there, too. It was only the MBP which had issues.
I don't *think* Macs have a BIOS to update. But I know my MBP has issues with certain HDD's (including another external which works fine on other Macs and all Windows machines).
You might be able to find my thread by searching under my username, perhaps something in there will offer a tip. Otherwise, you might have to go the same route I did: install a WD Scorpio Black instead. Or upgrade to an SSD.
Good luck to you-

My WD 2tb external hard drive will not unmount from my MacBook Pro.

My WD 2tb external hard drive will not unmount from my MacBook Pro. It no longer even shows up in finder, however it does show up in Disk Utility. I have tired so many of the suggestions on the internet all to a fail.
I keep getting the message to be sure that all applications are closed before ejecting the drive. I have no clue how to tell which appliactions are using the external drive to shut them off. I turned off Time Machiene to be safe.
I don't need anything on the external drive, I am just trying to erase it, save my current info, and migrate it to my new MacBook Pro.
I have been about four days now with this issue all over the internet, in this community, and watching videos on everything and nothing about this topic to a fail.
I think I am doomed and have lossed this external drive because of some wierd application that will NEVER close on my hard drive for it to disconnect correctly. It's annoying.
Does anyone have a solution?

Have you trie using another USB port? Can you test the USB ports with other USB devices to assure they are working? You may want to reinstall OS X in case there has been a driver glitch.
Reinstall OS X without erasing the drive
1. Repair the Hard Drive and Permissions
Boot from your Snow Leopard Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer.
If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
2. Reinstall Snow Leopard
If the drive is OK then quit DU and return to the installer. Proceed with reinstalling OS X. Note that the Snow Leopard installer will not erase your drive or disturb your files. After installing a fresh copy of OS X the installer will move your Home folder, third-party applications, support items, and network preferences into the newly installed system.
Download and install Mac OS X 10.6.8 Update Combo v1.1.

External hard drive will not eject

Since upgrading to ML my small "my passport" hard drive will not eject. First it gives me the message "the disk couldnt be ejected because Safari is using it and to close Safari and try again". (not sure why safari would be using it..) When I close safari then I get the message " the disk couldnt be eject because another program is using it"
My only option is to force eject each time.
Any suggestions?
Thanks
Susan
Mid 2011 15" macbook pro

Have you updated your "My Passport" software lately, there have been recent updates for Mountain Lion issues: http://community.wdc.com/t5/News-Announcements/bd-p/Announcements
http://community.wdc.com/t5/News-Announcements/Software-Update-WD-SmartWare-Upda te-1-3-4-x-for-Mac-Users-7-26/td-p/444122

My Hybrid 1TB Seagate Hard Drive will not work in my data doubler caddy installed in the optical bay

My Hybrid 1TB Seagate Hard Drive will not work in my data doubler caddy installed in the optical bay of my MacBook Pro

Thanks for all the advice. It looks like I have finally got my MBP working again (after two weeks of pain).
The WD HD works fine internally, but restoring from TM introduced a whole load more of issues/incompatabilities (see above). Eventually the only thing left was to re-build rather than restore:
i) mount the WD disk internally and install Snow Lepoard from the orginial installation disks
ii) get online, and after much trying download Lion (previously purchased). Perfrom all update.
iii) Connect my Time Capsule, identify my data, photo and music files and then copy them accross by hand
iv) install all the other applications (e.g. MS Office:mac, etc) from scratch.
This exercise has shown me that even though tools and procedures exist to address separate issues, when the complexity of inter-dependence is introduced there are a raft of problems that crop up.
Now I am back in business I will be using TM and CCC to take full and regular copies. I did this previously, which has saved me from losing my data and cherished pictures, but hopefully next time (and I'm sure there will be a next time) the recovery will be less infuriating.
BTW I got a refund on the Seagate Momentus XT. They guy in the shop said it wasn't the first time he'd heard of this issue with MBPs. Great.

External Hard Drive will not mount after upgrading to Yosemite

After upgrading to Yosemite, my external 3TB hard drive will not mount... can't see in Finder, but does appear in Disk Utility. Follow steps to Repair disk, but get a message that D.U. cannot repair disk.

See mount section.
Disk Unmount Using Terminal
Disk Utility – Force Mount Disk

M45-S165 with new Hard Drive will not reformat and recover.

Similar Messages

Maybe you are looking for