M93p BIOS issue: PowerOff not correct if Enhanced Power Saving Mode Disabled and Wake on Lan Enabled

Hi Levnovo support team, Recently I bought a M93p tiny(10AAA05MTW)(BIOS revision FBKT56A)and installed with Ubuntu 13.10 myself.Then tried to enable wake on lan for my tiny. The followings are my test result. 1. Enhanced Power Saving Mode Enabled, no mateter what is Wake On Lan setting PowerOff system is OK. 2. Enhanced Power Saving Mode Disable and Wake On Lan Disabled PowerOff system is OK. 3. Enhanced Power Saving Mode Disabled and Wake On Lan Primary or Automatic PowerOff system is NG. When I tried to power off system, it always can poweroff(LEDs on front all off) then POWER ON again in 2 or 3 seconds. I cannot accept this test result ,system should poweroff not reboot again. It's really hard to understand why enabling Wake on Lan will affect power off function. I tried the same procedures with my another M92p(3212A16)(BIOS revision 9SKT70AUS), and it works well.

Did you ever get a fix for this?Having the same issue on 3 of 6 machines that just arrived.

Similar Messages

W520 Docking issue - attached monitor won't enter power saving mod

When my W520 (Win2008R2) power management profile shuts the display off (after 10 mins, for example), the externally DVI connected screen no longer receives a signal, but the screen doesn’t go into power saving mode. Instead, the monitor stays powered on (the green power light normally turns yellow), and displays the message “Cannot display this mode”. It’s a Dell monitor, and this message appears to be a Dell message, nothing from the Lenovo or Windows.
It’s a new W520, and a new docking station – the ThinkPad Mini Dock Series 3 170W. The previous W510 and previous docking station ThinkPad Mini Dock Series 3 135W both worked fine with this monitor, and were able properly stop sending it a signal.
So…where do I start troubleshooting? Is this a Lenovo docking station issue? Are others having this problem?

hey DougWelsby,
welcome to the forums and for this is hard to say if it is the docking station or is it something else.
is it possible for you to test a different monitor with the docking station or to have test the current monitor of yours directly with the W520 ?
If you can, do reply back with your findings.
At the same time, do hop over to http://support.lenovo.com and crosscheck the download list and ensure all drivers (including bios) is up to date.
WW Social Media
Important Note: If you need help, post your question in the forum, and include your system type, model number and OS. Do not post your serial number.
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"!
Follow @LenovoForums on Twitter!
Have you checked out the Community Knowledgebase yet?!
How to send a private message? --> Check out this article.

I am using usb/my keyboard to record an original song. I play the melody on my keyboard but the rhythmic notation shown is not correct. i.e. a dotted 8th and 16th pattern has rests, 32 notes,etc. and most is incorrect. Any thoughts on how to fix this?

I am using usb/my keyboard to record an original song. I play the melody on my keyboard but the rhythmic notation shown is not correct. i.e. a dotted 8th and 16th pattern has rests, 32 notes,etc. and most is incorrect. Any thoughts on how to fix this?

What is your GarageBand version? Are you using the most recent GarageBand 10.0.x or an earlier version?
I play the melody on my keyboard but the rhythmic notation shown is not correct. i.e. a dotted 8th and 16th pattern has rests, 32 notes,etc. and most is incorrect. Any thoughts on how to fix this?
The rhythmic notation in GarageBand is the best estimate, based on the length of the notes you played and the "quantize" settings. You can correct the score somewhat by adjusting the note values in the Piano Roll view and by selecting notes and picking a suitable time quantize setting in the track editor, e.g., if you wanted to play triplets, set the quantize value correspondingly:
But I never could get GarageBand to show the dotted notes and rests correctly.
If your main goal is to create a musical score and not to mix music, better use notation software instead of GarageBand.

Dear sir, i am fully dis-appointed about my above case no : *******. I have face this problem last 9 and half months and still the issue is not resolved. This iPHONE4S purchase from Australia and now i am in india.

Dear sir,
i am fully dis-appointed about my above case no : *******. I have face this problem last 9 and half months and still the issue is not resolved. This iPHONE4S purchase from Australia and now i am in india. Your apple team told that the problem in your device and ready to replace it. But Now what happen they told you must have to send this iPHONE to Australia. But I have checked the courier people is not ready to take this device to australia. I will send it if any body of my relative comes to india but it will take a long time may be 8 to 10 months . I already suffering this problem since last 9 and half months and also for replacement it will take another 10 months. so it will very difficult for me. i request you to please send a new device at my address and i will send you this iPhone 4S return back when my some relative comes to australia.
<Post Edited By Host>

Just a reminder to you. Apple is not here. This is a user forum and the only people here are users like you. Posting the same rant multiple times achieves nothing. Keep it up and your future post will be deleted just like the one that just was.

My IPad screen is frozen with a message stating that the IPad has not been backed up to the ICloud for 7 weeks, this is not correct.I cannot get the messageto clear and cannot access any of the other icons; is there an emergency reboot process?

My IPad screen is frozen with a message stating that the IPad has not been backed up to the ICloud for 7 weeks, this is not correct. I cannot get the messageto clear and cannot access any of the other icons; is there an emergency reboot process?

Have you tried resetting your iPad?
Reset: Press the Home and On/Off buttons at the same time and hold them until the Apple logo appears (about 10-15 seconds).
No data will be lost.

Korean input keyboard not correct typing after ios7 upgrade at iPhone and iPad.

korean input keyboard not correct typing at page after ios7 upgrade at my iPhone and iPad.

Report this to Apple via
http://www.apple.com/feedback

All keyboard shortcuts are disabled, and I can't enable them - resetting firefox or safe mode not helping

For example, Ctrl-T is grayed out / disabled so I can't open a new tab using the keyboard.
Ditto for ALL other keyboard shortcuts - they're all disabled / grayed out.
PS - I've used Firefox for years, this happened about a month or so ago, and it's been that way ever since, even after rebooting computer.

'''Try Firefox Safe Mode''' to see if the problem goes away. [[Troubleshoot Firefox issues using Safe Mode|Firefox Safe Mode]] is a troubleshooting mode that turns off some settings, disables most add-ons (extensions and themes).
If Firefox is open, you can restart in Firefox Safe Mode from the Help menu:
*In Firefox 29.0 and above, click the menu button [[Image:New Fx Menu]], click Help [[Image:Help-29]] and select ''Restart with Add-ons Disabled''.
*In previous Firefox versions, click on the Firefox button at the top left of the Firefox window and click on ''Help'' (or click on ''Help'' in the Menu bar, if you don't have a Firefox button) then click on ''Restart with Add-ons Disabled''.
If Firefox is not running, you can start Firefox in Safe Mode as follows:
* On Windows: Hold the '''Shift''' key when you open the Firefox desktop or Start menu shortcut.
* On Mac: Hold the '''option''' key while starting Firefox.
* On Linux: Quit Firefox, go to your Terminal and run ''firefox -safe-mode'' <br>(you may need to specify the Firefox installation path e.g. /usr/lib/firefox)
When the Firefox Safe Mode window appears, select "Start in Safe Mode".<br>
[[Image:Safe Mode Fx 15 - Win]]
'''''If the issue is not present in Firefox Safe Mode''''', your problem is probably caused by an extension, and you need to figure out which one. Please follow the [[Troubleshoot extensions, themes and hardware acceleration issues to solve common Firefox problems]] article to find the cause.
''To exit Firefox Safe Mode, just close Firefox and wait a few seconds before opening Firefox for normal use again.''
When you figure out what's causing your issues, please let us know. It might help others with the same problem.

TS1363 I connect my ipad to my computer to do a sync but it is not showing up. My ipad is disabled and I need to sync it back to the computer. I have the ipad plugged into the computer but the sync does not light up.

My ipad is disabled and when I connect to the computer to sync it is not finding it. I don't know what I need to do to fix it so that I can sync. Please help

Restore your ipad

Aperture not automatically Pushing new Photostream photos without disabling and enabling again

Hi I have an iPhone 4 runing iOS 5.0.1 with Photostream enabled.
My mac also has Photostream enabled on the same account.
Aperture 3.2.2 also has Photostream enabled on the same account.
When I take a photo with my iPhone, it does not automatically come up in Photostream, after waiting some time with a strong and tested Wifi connection.
Photos only appear in Aperture's Photostream when going to Aperture>Prefrences and disabling and re-enabling Photstream.
Both checkboxes are ticked underneath 'enable photostream'

I have the same setup as you. Mac with Lion 10.7.2, iPhone 4 and Aperture 3.2.2. I havn't observed the photostream much but a couple of times I had Aperture open and took some screenshots on my iPhone. It took a bout 10 minutes for them to show up in Aperture's Photo Stream folder. The last time I took 4 screenshots and only 3 showed up in Apertures Photo Stream. The next day I opened Aperture and the 4 was there too. Seems to me to be a little hit and miss.

6714 Ver 1 BIOS issue : will not boot OS

Hi ya,
I'm wondering if there's a way to force the flash program to replace the BIOS even though it detects it as a different / incorrect version ?
Just having an interesting problem with an old(ish) MSI 6714 motherboard.
The system was installed and working fine on a users desk, however we replaced the 6714 machine with a newer one and were going to re-format 6714 system, re-install the OS and use it to replace another users system.
During the OS installation (Windows 2K SP3 corp media), after the first re-boot the system will blue screen with an error similar to IRQ_NOT_EQUAL_TO or something to that effect.
No matter how we installed the system it kept dying at the same point.
I tried ghosting a copy of the OS onto the HDD, however it gets to the initial 'Windows 2K press F8' part, the loading line flicks across, and then it hangs.
The machine always POSTS and always allows entry to the BIOS.
A strange thing is though, if you change the 'USB Mouse Support' option from Disabled to Enabled then the system POSTS as normal but dies before it even brings up the 'Windows 2K press F8' section.
Looking at the BIOS though I think this system has been installed with an 845GEM Bios, when it may have needed the 845GVM Bios instead .. as the board has no AGP slot.
I've found some other people in the Forum's who have encountered a similar issue, but none of the links in the replies have worked.
The current BIOS on the sustem is the 2003/05/07 845GEM v1.2 BIOS (4Mb)
There isn't an updated version of this BIOS, and this was the BIOS version that was on the system before I started messing around with it (I tried over-writting it again but it does the same thing when booting the OS).
To be honest I think I encountered the same problem when I first got the system, but I somehow got it working by ghosting a copy of the OS onto the system. That may have just been pure luck though .. as nothing I've tried has gotten this system to work.
Specs are :
AOpen H340D case
MSI 6714 Ver:1 (BIOS 845GEM v1.2 2003/05/07)
256Mb DDR266 (tested with MEMtest without error)
WD 300B/400B drives (we've tried a few)
Also tried it with a PCI graphics card to no effect.
All capaciters are flat and look in good condition.
All cables have been checked and changed.
Thanks ???

Thanks Greyone, but I think I found the problem.
In answer to your Q though, the chip in front of where the AGP slot should be has a sticker on it saying 845GV ICH4.
System was made up by one of our venders. But I'm not sure if they could have been the culprit for the incorrect BIOS though as they would have had to have forced the BIOS onto the system since it returns a BIOS-Lock error if you try the GEM Bios on a GVM system and vice versa.
I downloaded the MSI-6714 845GVM v4.2 bios and flashed it with the /f switch, and it seems to be running ok.
Windows 2K had to find all the hardware again (and required the driver files for the GFX card), but it does now seem to be running and stable (that is if you can call something stable thats only been running for 45 minutes thus-far )
Hope this post can help out anyone else who comes across this issue though.
Thanks

Lightroom color issue, Export not correct color

Recently when exporting, the images in the folder are discolored, but when the same image is uploaded into blogstomp and PASS the previews are discolored but the image when viewed online is correct. Then today I uploaded some images into my website using Showit and they were discolored even online. I reset to defaults in the preferences/presets section but that didn't help...I have no idea what is going on.

Thanks for your guidance...
I don't think it's a monitor issue, so we'll go to the images first:
Here is the incorrect:
http://katieplusryan.mauicreative.com/#/gallery/
Here is the correct:
http://blog.mauicreative.com/fall2013/
When exported, the images in the edits folder look great, upload them into blogstomp and they look like example #1, upload the very same file to the blog and it looks like example #2.
I viewed on my iPhone, on chrome and in firefox and all the same scenario...
Thanks for your help!

Has Mountain Lion solved the issue of not all sent emails being saved?

The Snow Leopard forum has a thread about Mac Mail not saving every sent item in the "Sent" folder. My email account is IMAP and it seems to work fine for most of the time except that, every now and again, a message is sent (and it really is sent) but never appears in the "Sent" folder on either my Mac Mail or the synched folder on my ISP server. This seems to happen when a message takes a long time to get to the end of the activity bar before the usual "whooshing" sound and it has been suggested that the delay causes Mac Mail to delete the message. The SL forum left the issue unresolved but I have not seen any reports of the problem being there on ML so wonder if it has been fixed and my problem lies with my ISP rather than my iMac. Has anyone else experienced this problem on ML?

My primary email account is IMAP and I have just found what I suspect are all the messages that were not saved in my "sent" folder either on my iMac or ISP server. They were in the "Sent" folder of my secondary, little-used Hotmail account and the recipients "saw" these as originating from this account rather than the one from which I actually sent them. After some testing, I discovered that, for my primary account, the "always use this server" box was not checked. I surmise that, if the Mail app has trouble using the server associated with my primary account, it simply uses the Hotmail server (this would be consistent with the delay before hearing the "whooshing"noise). What does surprise me is that, if this Hotmail server has been used, the recipient sees the message as originating from Hotmail. Is this what is supposed to happen?

CS5 issue - Text not keeping Vector format when saving as PDF

Hi everybody,
I am very frustrated right now. I am working in PS CS5 in Windows, and I cannot get the text to keep the raster format where it's cleaner / clearer, and can be highlighted, searched for, etc.
What's really puzzling is that it will work sometimes, but other times it will not, and I'm not doing anything different. Some text layers keep the vector format, and some do not. I've searched, and the only solution I see is for older versions of PS where it just says to select the "keep vector format" checkbox, which is not in the save options in CS5.
Can anyone help me out with this? Any assistance would be much appreciated!!
Trevor

Hello!
Yes, faux bold is an effect on the text that can't be vectorized.
You'll need to change your font to another one that has a "real" bold option.

Topichead does not convert properly when ditamap saved as book and hierarchy not maintained

I'm new to DITA and piloting some documents in FrameMaker 12, trying to get the output that I need.
I have created a ditamap with a structure as follows:
Map title
- Concept A
- Topichead
   - Task A
   - Task B
- Concept B
- Task C
   - Task D
I would like this to ouptut a PDF with TOC and bookmarks as follows:
Map title => book title
- Concept A => Chapter 1
- Topichead => Chapter 2
   - Task A => Chapter 2.1
   - Task B => Chapter 2.2
- Concept B => Chapter 3
- Task C => Chapter 3.1
- Task D => Chapter 3.2
To do this I save the ditamap as a "Book 12.0 with fm components (*.book)" and set the Bookmark levels in the PDF Setup as follows:
ChapterTitle
head.0
Title
title.0
.title.1
..title.2
...title.3
However, the output systematically comes out wrong because the Topichead element, which is just a title and is not attached to any topic, is not taken into account as a hierarchical element in the output. It generates an empty fm document containing just the topichead title, output as a ChapterTitle or Title depending on whether I set its toc attribute to yes. But the TOC is all wrong - instead of taking Task A and Task B as children of Chapter 2 it puts them all at level 1 so I get:
- Concept A => Chapter 1
- Topichead => ignored
   - Task A => Chapter 2
   - Task B => Chapter 3
- Concept B => Chapter 4
- Task C => Chapter 4.1
- Task D => Chapter 4.2
If I output using the bog-standard DITA-OT instead of fancy and expensive FrameMaker, everything comes out correctly.
Is there any way to correct this?
Thanks,
Archaeopteryx

Hi Archaeopteryx...
I beieve that FM only uses the elements from topics to create the output .. as you're seeing, headings in the map are ignored. I also believe that the process that FM uses to aggregate the topics into FM files is hard-coded somewhere in the DITA plugin, and not exposed for modification .. so aside from developing a plugin to modify the process, I think you're out of luck if you're using the default DITA support. The only solution would be to include title-only topics in the structure that provide those headings rather than using a topichead.
However, you might want to check out DITA-FMx, in which the aggregation process is controlled by XSLT that you are free to modify. The default book-build process in DITA-FMx also ignores these map elements, and assumes that all content is defined in topics, but you could tweak the XSLT to include topicheads as topic headings in the generated book.
     http://leximation.com/dita-fmx/
Thanks,
Scott Prentice
Leximation, Inc.
www.leximation.com

Yoga 2 Pro issues: display flashing, no recovery from power saving, blue screens

I believe I've narrowed down a problem with the machine not coming out of sleep mode, and maybe blue screening. There is a new version of virtualbox that I've installed and it is suppose to help.
Issues still present
1) I have found the screen to become corrupted where it flashes on and off. I end up doing a hard reboot to fix the issue temporarily.
2) Sometimes (when virtualbox isn't running), the display goes into powersaving mode and doesn't recover. I had this issue with Linux installed (kubuntu 13.10) as well as with windows 8.1.
3) Rare screen corruption where the display jumps for a split second and then goes back to normal. This is very rare. It may happen 3-4 times a day but I use this system for development so this is scary and unacceptable.
Any input would be appreciated!
How I reinstalled Windows 8.1:
Installed windows 8 from UEFI media (with an old/supported wifi USB), updated, installed 8.1 upgrade, then installed drivers
Drivers installed:
bt, dptf, tp, emw
The default Windows 8.1 drivers included the full intel driver set. I've considered upgrading, but these issues were present before I reinstalled Windows 8.1 w/ UEFI media and I had the full driver set from the lenovo website installed at the time.
Solved!
Go to Solution.

I spoke with support for quite a while today.
It is not sleep mode that is causing the machine to become unresponsive. If you disable "turn the display off after", then it will go to sleep like normal. If you have "turn the display off" enabled, it crashes and neither goes to sleep, nor allows the display to turn back on.
If I close the lid it goes to sleep, and opening the lid wakes the machine up again.
I installed the chipset driver from the support website, rebooted, and reenabled screen blanking in power settings.
I have been unable to get the machine not to wake after screen blanking and sleeping. I set it to 1m blank and 2m sleep and it goes blank and recovers if I hit a key. If you let it go 2m, it sleeps and recovers as intended. I'm very releaved as I did NOT want to return this.
The power management issue seems to be resolved by reinstalling the chipset driver from the website.
I'm going to see if I still have the display flashing issues anymore. Perhaps it is solved as well!!
Thanks Lenovo!
EDIT: I spoke too soon!! It just did it again.

M93p BIOS issue: PowerOff not correct if Enhanced Power Saving Mode Disabled and Wake on Lan Enabled

Similar Messages

Maybe you are looking for