Mac devices 'see' my express but can't make connection
I have installed an Airport Express to access the web and to wirelessly play music to connected speakers. I have Ethernet connected internet (when it works) via TP-Link (TL-PA211 and TL-WPA281). My devices (Ipad and iPhone4) see the network but when I select within 'Wi-Fi' the wheel just keeps spinning and a connection is not established. I have tried 'forgetting network' and restarting devices and Express. Any suggestions?
There are three Airport resets, soft, hard and factory default. It would probably be beneficial if you tried each one in sequence. Actually, you could jump to the factory default reset if you don't mind reconfiguring from scratch.
Similar Messages
-
Can see Airport Express, but iTunes won't connect and more..
I'm running Mac OSX 10.4.2 on an Aluminium PowerBook G4, connected to an Airport Extreme Base Station - which can use the internet etc easily. I have an Airport Express, which can be seen & changed in Airport Admin, and can be seen in iTunes - but can not be connected to in iTunes - it tries for about 30 seconds, and then gives up, not even an error message? I'm not sure if it's a related issue, buit an old iBook running OSX 10.3.9, connects to the same Airport Express, no problems. But the PowerBook, whilst it can see the iBook, won't connect to the iBook via Airport - it tells me it is not operational, or something.
Can anyone think of anything that may fix the problem?
Thanks in advance.Is this a new problem on this Powerbook - or has it never worked? While there are many (and some very obscure) causes for this problem, one of the more common causes is firewall software of some sort. This also includes applications designed to monitor outgoing network data (like spyware) on a Mac, like "Little Snitch".
-
I am using Windows XP Professional 2002 w/ SP3 on a Dell Latitude E4300 laptop wirelessly connecting to my Airport Express 802.11n (firmware 7.5.2).
I can see my Airport Express in iTunes 10.4.1 and can select it via the Airplay button. iTunes even detects whether or not a speaker is connected to the Airport Express. But when iTunes tries to connect, it comes back after a while saying "An error occurred while connecting to the Airplay device xxx. An unknown error occurred (error -15000)."
A similar problem happens with Airfoil from Rogue Amoeba that I use to stream music from other apps such as VideoLAN to Airport Express on the same laptop. I can see that my Airport Express is available but when Airfoil tries to connect, it comes back saying "It appears that a firewall on this computer is preventing Airfoil from connecting to xxx Airport Express. Please check your firewall settings and try again."
I've set both Airplay and iTunes as exception programs in my Windows Firewall setting, and even added TCP ports 5000 to 5005 and UDP ports 6000 to 6005 to the exceptions as recommended by Airfoil. I've also disabled Symantec Endpoint Protection that Ihave installed. The only thing I can't disable is McAfee Endpoint Encryption, since I also use the laptop at work and I don't have permission to disableMcAfee. I use this laptop to connect wirelessly with other devices such as HP wireless printers, NAS drives and other laptops on my home network and have never had any issues, so i think that this issue is specific to the Airplay software being blocked by some firewall (I am assuming Airfoil also uses Airplay).
I've tried this on different wireless networks and I have the same issue with Windows XP on my Dell Latitude E4300. I've also set up the network with no security, but the problem doesn't go away.
I also tried downgrading iTunes to 10.3.1 but won't work. I think it's an Airplay issue, not a specific iTunes issue, since I'm facing the problem with Airfoil as well.
How do I trace what is going on that is preventing iTunes and Airfoil from streaming to the AirportExpress within Windows XP?
I also have another Dell Inspiron laptop on the same network running on Windows Vista, and have no problems streaming music from iTunes or Airfoil to the Airport Express on the same network, even when the network is WPA-2 Personal (TKIP+AES) protected (I've seen other postings where WPA has been an issue, WEP has not, but in my case, this is not an issue). Ditto with my iPad2.
Thanks for your help!I have the same problem with Windows 7 64bit. ITune can see AE and stream Music well. Airfoil, TuneBlade (airplay soft) can also see AE but can't connect and stream music. I ' ve already tried to setup firewall Exception list, even turning off firewall off both windows and antivirus but still got the same problem with the message 'Airfoil was unable to connect to the remote speaker " ... 's Airport Express". Please check the firewall on the computer where " ...'s Airport Express" is running and try again'. Any help would be appreciated !.
-
I am running OS X 10.5.8 and don't see an iCloud icon in my system preferences. I do see a Mobileme icon but I would like to have all my mac devices on iCloud. How can I get iCloud on my desktop?
iCloud requires 10.7.2 or later. See the following about how to upgrade:
Upgrade Paths to Snow Leopard, Lion, and/or Mountain Lion
You can upgrade to Mountain Lion from Lion or directly from Snow Leopard. Mountain Lion can be downloaded from the Mac App Store for $19.99. To access the App Store you must have Snow Leopard 10.6.6 or later installed.
Upgrading to Snow Leopard
You can purchase Snow Leopard through the Apple Store: Mac OS X 10.6 Snow Leopard - Apple Store (U.S.). The price is $19.99 plus tax. You will be sent physical media by mail after placing your order.
After you install Snow Leopard you will have to download and install the Mac OS X 10.6.8 Update Combo v1.1 to update Snow Leopard to 10.6.8 and give you access to the App Store. Access to the App Store enables you to download Mountain Lion if your computer meets the requirements.
Snow Leopard General Requirements
1. Mac computer with an Intel processor
2. 1GB of memory
3. 5GB of available disk space
4. DVD drive for installation
5. Some features require a compatible Internet service provider;
fees may apply.
6. Some features require Apple’s iCloud services; fees and
terms apply.
Upgrading to Lion
If your computer does not meet the requirements to install Mountain Lion, it may still meet the requirements to install Lion.
You can purchase Lion by contacting Customer Service: Contacting Apple for support and service - this includes international calling numbers. The cost is $19.99 (as it was before) plus tax. It's a download. You will get an email containing a redemption code that you then use at the Mac App Store to download Lion. Save a copy of that installer to your Downloads folder because the installer deletes itself at the end of the installation.
Lion System Requirements
1. Mac computer with an Intel Core 2 Duo, Core i3, Core i5, Core i7,
or Xeon processor
2. 2GB of memory
3. OS X v10.6.6 or later (v10.6.8 recommended)
4. 7GB of available space
5. Some features require an Apple ID; terms apply.
Upgrading to Mountain Lion
To upgrade to Mountain Lion you must have Snow Leopard 10.6.8 or Lion installed. Purchase and download Mountain Lion from the App Store. Sign in using your Apple ID. Mountain Lion is $19.99 plus tax. The file is quite large, over 4 GBs, so allow some time to download. It would be preferable to use Ethernet because it is nearly four times faster than wireless.
OS X Mountain Lion - System Requirements
Macs that can be upgraded to OS X Mountain Lion
1. iMac (Mid 2007 or newer) - Model Identifier 7,1 or later
2. MacBook (Late 2008 Aluminum, or Early 2009 or newer) - Model Identifier 5,1 or later
3. MacBook Pro (Mid/Late 2007 or newer) - Model Identifier 3,1 or later
4. MacBook Air (Late 2008 or newer) - Model Identifier 2,1 or later
5. Mac mini (Early 2009 or newer) - Model Identifier 3,1 or later
6. Mac Pro (Early 2008 or newer) - Model Identifier 3,1 or later
7. Xserve (Early 2009) - Model Identifier 3,1 or later
To find the model identifier open System Profiler in the Utilities folder. It's displayed in the panel on the right.
Are my applications compatible?
See App Compatibility Table - RoaringApps.
For a complete How-To introduction from Apple see Upgrade to OS X Mountain Lion. -
Why won't my iMac print consistantly to my compatible HP 6500A? I've checked for updates and downloaded the lasted software...still can't print. All my other Mac devices find the printer but the iMac is hit and miss. I'm operating the Mac OS X Lion 10.7.
When you say hit and miss do you mean sometimes you print a whole document with no problems, or do you mean each document has problems? This is from HP's website for your printer:
Your sig says 10.6.7 but your message says 10.7. So if it's really Lion, this printer isn't officially supported. Elsewhere on HP's site it says updated drivers will be available on your Mac via Software Update. Have you run that recently? -
HT1338 my mac won't send emails but can receive them
mac won't send emails but can receive them
Hi Mick209
I am in the UK and eventually found the problem was due to my BT Home Hub Router. Not sure where you live, but of you are in the UK, this might work for you.
I found this fix below on https://discussions.apple.com/thread/4604180?start=15&tstart=0
It worked for me. If you can't link to the URL, here is the body of the text
There's an issue related to the BT homehub that is providing a hostname that is "syntactically incorrect" for several smtp server.
Here's how you can fix it.
Using your internet browser, go to the address "192.168.1.254
- Follow instructions to reset your password if asked.
- Then go to "Settings", then "Advanced Settings" and "home network"
You will see there all the devices that are connected or that has been connected before. It's gonna be easyer if yout computer is the only one connected.
Your computer should have a name like "unknown-xx:xx:xx:xx:xx ...
Click on this name, chose another name without any special characters, like "macbook" for exemple.
And then click on "apply"
- restart your computer.
That should fix the issue.
Credit goes to vincentfromcork for providing me with the solution.
If it works, spread the word :-) -
When I try to go on the internet with my iPad 2, the whole section is greyed out. I can see the webpage, but can not navigate any further. I do have wifi access, though.
Try:
- A reset. Nothing will be lost.
Reset iPod touch: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears
- Power off and then back on the router
- Reset Network Settings: Settings>General>Reset>Reset Network Settings
- iOS: Troubleshooting Wi-Fi networks and connections -
I cannot send a text thru iMessage. I followed the directions over and over again but can't make it work. Also how can I find out all the apple ids I may have.
A wet phone is out of warranty. This is considered user damage. Even if you were able to get it to start now, the chances of it working for long are slim. I suggest going to Apple and see about an OOW replacement. One for the iPhone 4 is only $149USD and it would come with a short warranty. It is a refurbished device and you would not be worried about encountering additional problems.
-
Brand new owner IMac desktop, with One to one service, but can't make an appt??
I just brought home the Imac & paid for a One to One, but can't make an appt online??
http://www.apple.com/retail/learn/one-to-one/ or just call AppleCare or the store from which you purchased the machine. If you're switching from PCs, see these:
Switching from Windows to Mac OS X,
Basic Tutorials on using a Mac,
Mac 101: Mac Essentials,
Mac OS X keyboard shortcuts,
Anatomy of a Mac,
MacTips,
Switching to Mac Superguide, and
Switching to the Mac: The Missing Manual, Lion Edition.
Additionally, *Texas Mac Man* recommends:
Quick Assist,
Welcome to the Switch To A Mac Guides,
Take Control E-books, and
A guide for switching to a Mac. -
VPN Client can't reach router or hosts, but can reach other connected sites.
We have a VPN client configuration on a 2901 router. The client passes authentication and connects fine. When connected, cannot reach the 2901 or any devices directly behind it, BUT can reach routers and hosts that are connected to the same 2901 through site to site connections.
Few notes:
I have added some lines excluding NAT in a few different ways, but does not resolve.
I have switched the RAP rool from 10.96.20.x to 172.21.20.x and can then connect to the local host. Appears to be a routing issue to the 10.x network, but I can't seem to find the solution.
Any help would be greatly appreciated. Here is the config:
boot-start-marker
boot system flash
boot system flash:c2900-universalk9-mz.SPA.153-2.T.bin
no ip domain lookup
ip inspect log drop-pkt
ip inspect name FIREWALL tcp
ip inspect name FIREWALL udp
ip inspect name FIREWALL ftp
ip inspect name FIREWALL fragment maximum 256 timeout 1
ip inspect name FIREWALL ntp
ip inspect name FIREWALL pptp
ip inspect name FIREWALL dns
ip inspect name FIREWALL l2tp
ip inspect name FIREWALL pop3
ip inspect name FIREWALL icmp router-traffic
no ipv6 cef
crypto isakmp policy 1
encr aes
authentication pre-share
group 2
crypto isakmp policy 5
encr 3des
authentication pre-share
group 2
crypto isakmp policy 10
encr 3des
hash md5
authentication pre-share
group 2
crypto isakmp policy 95
authentication pre-share
group 2
crypto isakmp policy 99
hash md5
authentication pre-share
group 2
crypto isakmp policy 110
hash md5
authentication pre-share
crypto isakmp client configuration group VPN-RAS
key *********
dns 10.96.17.2 10.1.200.50
wins 10.96.17.2 10.1.200.50
domain mine.com
pool RAPOOL
acl SPLIT
save-password
split-dns mind.com
netmask 255.255.255.0
crypto isakmp profile USERS
match identity group VPN-RAS
client authentication list DOMAIN
isakmp authorization list VPN-RAS
client configuration address respond
keepalive 300 retry 5
crypto ipsec transform-set AES128 esp-aes esp-sha-hmac
mode tunnel
crypto ipsec transform-set 3DES esp-3des esp-sha-hmac
mode tunnel
crypto ipsec transform-set DES esp-des esp-md5-hmac
mode tunnel
crypto ipsec transform-set 3DES-MD5 esp-3des esp-md5-hmac
mode tunnel
crypto ipsec transform-set DES-SHA esp-des esp-sha-hmac
mode tunnel
crypto ipsec transform-set myset esp-3des esp-sha-hmac
mode tunnel
crypto dynamic-map dynmap 1
set transform-set AES128
set isakmp-profile USERS
crypto map COMPANY_VPN 10 ipsec-isakmp
set peer *******
set transform-set 3DES-MD5
match address PA-VPN
qos pre-classify
crypto map COMPANY_VPN 50 ipsec-isakmp
set peer ******
set transform-set AES128
match address VPN
qos pre-classify
crypto map COMPANY_VPN 999 ipsec-isakmp dynamic dynmap
interface Embedded-Service-Engine0/0
no ip address
shutdown
interface GigabitEthernet0/0
ip address 37.222.111.224 255.255.255.248
ip access-group INBOUND in
no ip redirects
no ip unreachables
no ip proxy-arp
ip verify unicast reverse-path
ip flow ingress
ip flow egress
ip nat outside
ip inspect FIREWALL out
ip virtual-reassembly in
duplex auto
speed auto
no cdp enable
no mop enabled
crypto map COMPANY_VPN
interface GigabitEthernet0/1
no ip address
ip flow ingress
duplex auto
speed auto
interface GigabitEthernet0/1.17
description LAN
encapsulation dot1Q 17
ip address 10.96.17.253 255.255.255.0
ip access-group OUTBOUND in
ip flow ingress
ip flow egress
ip nat inside
ip virtual-reassembly in
standby 0 ip 10.96.17.254
standby 0 priority 110
standby 0 preempt
standby 0 track 1 decrement 20
interface GigabitEthernet0/1.27
description VOICE
encapsulation dot1Q 27
ip address 192.168.17.254 255.255.255.0
ip access-group OUTBOUND in
ip helper-address 10.96.17.2
ip flow ingress
ip nat inside
ip virtual-reassembly in
h323-gateway voip bind srcaddr 192.168.17.254
ip local pool RAPOOL 10.96.20.50 10.96.20.150
ip forward-protocol nd
ip nat inside source route-map NAT-POOL interface GigabitEthernet0/0 overload
ip route 0.0.0.0 0.0.0.0 37.222.111.223
ip route 10.96.16.0 255.255.255.0 10.96.17.250
ip route 172.22.1.0 255.255.255.0 10.96.17.250
ip route 172.22.2.0 255.255.255.0 10.96.17.250
ip route 172.22.3.0 255.255.255.0 10.96.17.250
ip route 192.168.16.0 255.255.255.0 10.96.17.250
ip access-list extended DMZ
deny ip any 10.0.0.0 0.255.255.255
deny ip any 192.168.0.0 0.0.255.255
permit ip any any
ip access-list extended GUEST
deny ip any 10.0.0.0 0.255.255.255
deny ip any 192.168.0.0 0.0.255.255
permit ip any any
ip access-list extended INBOUND
deny ip 80.25.124.0 0.0.0.255 any
deny ip 10.0.0.0 0.255.255.255 any
deny ip 172.16.0.0 0.15.255.255 any
permit udp host 173.239.147.114 any eq isakmp
permit esp host 173.239.147.114 any
deny ip 192.168.0.0 0.0.255.255 any
permit udp any host 37.222.111.224 eq isakmp
permit udp any host 37.222.111.224 eq non500-isakmp
permit esp any host 37.222.111.224
ip access-list extended NAT
deny ip 10.96.20.0 0.0.0.255 any
deny ip any 10.96.20.0 0.0.0.255
permit ip 192.168.0.0 0.0.255.255 any
permit ip 10.0.0.0 0.255.255.255 any
ip access-list extended NONAT
permit ip any 192.168.0.0 0.0.255.255
permit ip any 10.0.0.0 0.255.255.255
ip access-list extended OUTBOUND
deny udp any host 22.55.77.106 eq isakmp
deny udp any host 22.55.77.106 eq non500-isakmp
deny esp any host 22.55.77.106
permit ip any any
ip access-list extended PA-VPN
permit ip 10.0.0.0 0.255.255.255 10.96.18.0 0.0.0.255
permit ip 10.0.0.0 0.255.255.255 192.168.18.0 0.0.0.255
permit ip 192.168.0.0 0.0.255.255 10.96.18.0 0.0.0.255
permit ip 192.168.0.0 0.0.255.255 192.168.18.0 0.0.0.255
ip access-list extended SPLIT
permit ip 10.0.0.0 0.255.255.255 any
permit ip 192.168.0.0 0.0.255.255 any
ip access-list extended VPN
permit ip 10.96.16.0 0.0.0.255 10.0.0.0 0.255.255.255
permit ip 10.96.17.0 0.0.0.255 10.0.0.0 0.255.255.255
permit ip 10.96.18.0 0.0.0.255 10.0.0.0 0.255.255.255
permit ip 10.96.0.0 0.0.255.255 192.168.0.0 0.0.255.255
permit ip 10.96.0.0 0.0.255.255 10.0.0.0 0.255.255.255
permit ip 192.168.16.0 0.0.0.255 192.168.0.0 0.0.255.255
permit ip 192.168.17.0 0.0.0.255 192.168.0.0 0.0.255.255
permit ip 192.168.18.0 0.0.0.255 192.168.0.0 0.0.255.255
permit ip 192.168.17.0 0.0.0.255 10.0.0.0 0.255.255.255
permit ip 192.168.18.0 0.0.0.255 10.0.0.0 0.255.255.255
permit ip 172.22.0.0 0.0.255.255 10.0.0.0 0.255.255.255
permit ip 172.22.0.0 0.0.255.255 192.168.0.0 0.0.255.255
route-map NAT-POOL deny 5
match ip address NONAT
route-map NAT-POOL permit 10
match ip address NATWe have a VPN client configuration on a 2901 router. The client passes authentication and connects fine. When connected, cannot reach the 2901 or any devices directly behind it, BUT can reach routers and hosts that are connected to the same 2901 through site to site connections.
Few notes:
I have added some lines excluding NAT in a few different ways, but does not resolve.
I have switched the RAP rool from 10.96.20.x to 172.21.20.x and can then connect to the local host. Appears to be a routing issue to the 10.x network, but I can't seem to find the solution.
Any help would be greatly appreciated. Here is the config:
boot-start-marker
boot system flash
boot system flash:c2900-universalk9-mz.SPA.153-2.T.bin
no ip domain lookup
ip inspect log drop-pkt
ip inspect name FIREWALL tcp
ip inspect name FIREWALL udp
ip inspect name FIREWALL ftp
ip inspect name FIREWALL fragment maximum 256 timeout 1
ip inspect name FIREWALL ntp
ip inspect name FIREWALL pptp
ip inspect name FIREWALL dns
ip inspect name FIREWALL l2tp
ip inspect name FIREWALL pop3
ip inspect name FIREWALL icmp router-traffic
no ipv6 cef
crypto isakmp policy 1
encr aes
authentication pre-share
group 2
crypto isakmp policy 5
encr 3des
authentication pre-share
group 2
crypto isakmp policy 10
encr 3des
hash md5
authentication pre-share
group 2
crypto isakmp policy 95
authentication pre-share
group 2
crypto isakmp policy 99
hash md5
authentication pre-share
group 2
crypto isakmp policy 110
hash md5
authentication pre-share
crypto isakmp client configuration group VPN-RAS
key *********
dns 10.96.17.2 10.1.200.50
wins 10.96.17.2 10.1.200.50
domain mine.com
pool RAPOOL
acl SPLIT
save-password
split-dns mind.com
netmask 255.255.255.0
crypto isakmp profile USERS
match identity group VPN-RAS
client authentication list DOMAIN
isakmp authorization list VPN-RAS
client configuration address respond
keepalive 300 retry 5
crypto ipsec transform-set AES128 esp-aes esp-sha-hmac
mode tunnel
crypto ipsec transform-set 3DES esp-3des esp-sha-hmac
mode tunnel
crypto ipsec transform-set DES esp-des esp-md5-hmac
mode tunnel
crypto ipsec transform-set 3DES-MD5 esp-3des esp-md5-hmac
mode tunnel
crypto ipsec transform-set DES-SHA esp-des esp-sha-hmac
mode tunnel
crypto ipsec transform-set myset esp-3des esp-sha-hmac
mode tunnel
crypto dynamic-map dynmap 1
set transform-set AES128
set isakmp-profile USERS
crypto map COMPANY_VPN 10 ipsec-isakmp
set peer *******
set transform-set 3DES-MD5
match address PA-VPN
qos pre-classify
crypto map COMPANY_VPN 50 ipsec-isakmp
set peer ******
set transform-set AES128
match address VPN
qos pre-classify
crypto map COMPANY_VPN 999 ipsec-isakmp dynamic dynmap
interface Embedded-Service-Engine0/0
no ip address
shutdown
interface GigabitEthernet0/0
ip address 37.222.111.224 255.255.255.248
ip access-group INBOUND in
no ip redirects
no ip unreachables
no ip proxy-arp
ip verify unicast reverse-path
ip flow ingress
ip flow egress
ip nat outside
ip inspect FIREWALL out
ip virtual-reassembly in
duplex auto
speed auto
no cdp enable
no mop enabled
crypto map COMPANY_VPN
interface GigabitEthernet0/1
no ip address
ip flow ingress
duplex auto
speed auto
interface GigabitEthernet0/1.17
description LAN
encapsulation dot1Q 17
ip address 10.96.17.253 255.255.255.0
ip access-group OUTBOUND in
ip flow ingress
ip flow egress
ip nat inside
ip virtual-reassembly in
standby 0 ip 10.96.17.254
standby 0 priority 110
standby 0 preempt
standby 0 track 1 decrement 20
interface GigabitEthernet0/1.27
description VOICE
encapsulation dot1Q 27
ip address 192.168.17.254 255.255.255.0
ip access-group OUTBOUND in
ip helper-address 10.96.17.2
ip flow ingress
ip nat inside
ip virtual-reassembly in
h323-gateway voip bind srcaddr 192.168.17.254
ip local pool RAPOOL 10.96.20.50 10.96.20.150
ip forward-protocol nd
ip nat inside source route-map NAT-POOL interface GigabitEthernet0/0 overload
ip route 0.0.0.0 0.0.0.0 37.222.111.223
ip route 10.96.16.0 255.255.255.0 10.96.17.250
ip route 172.22.1.0 255.255.255.0 10.96.17.250
ip route 172.22.2.0 255.255.255.0 10.96.17.250
ip route 172.22.3.0 255.255.255.0 10.96.17.250
ip route 192.168.16.0 255.255.255.0 10.96.17.250
ip access-list extended DMZ
deny ip any 10.0.0.0 0.255.255.255
deny ip any 192.168.0.0 0.0.255.255
permit ip any any
ip access-list extended GUEST
deny ip any 10.0.0.0 0.255.255.255
deny ip any 192.168.0.0 0.0.255.255
permit ip any any
ip access-list extended INBOUND
deny ip 80.25.124.0 0.0.0.255 any
deny ip 10.0.0.0 0.255.255.255 any
deny ip 172.16.0.0 0.15.255.255 any
permit udp host 173.239.147.114 any eq isakmp
permit esp host 173.239.147.114 any
deny ip 192.168.0.0 0.0.255.255 any
permit udp any host 37.222.111.224 eq isakmp
permit udp any host 37.222.111.224 eq non500-isakmp
permit esp any host 37.222.111.224
ip access-list extended NAT
deny ip 10.96.20.0 0.0.0.255 any
deny ip any 10.96.20.0 0.0.0.255
permit ip 192.168.0.0 0.0.255.255 any
permit ip 10.0.0.0 0.255.255.255 any
ip access-list extended NONAT
permit ip any 192.168.0.0 0.0.255.255
permit ip any 10.0.0.0 0.255.255.255
ip access-list extended OUTBOUND
deny udp any host 22.55.77.106 eq isakmp
deny udp any host 22.55.77.106 eq non500-isakmp
deny esp any host 22.55.77.106
permit ip any any
ip access-list extended PA-VPN
permit ip 10.0.0.0 0.255.255.255 10.96.18.0 0.0.0.255
permit ip 10.0.0.0 0.255.255.255 192.168.18.0 0.0.0.255
permit ip 192.168.0.0 0.0.255.255 10.96.18.0 0.0.0.255
permit ip 192.168.0.0 0.0.255.255 192.168.18.0 0.0.0.255
ip access-list extended SPLIT
permit ip 10.0.0.0 0.255.255.255 any
permit ip 192.168.0.0 0.0.255.255 any
ip access-list extended VPN
permit ip 10.96.16.0 0.0.0.255 10.0.0.0 0.255.255.255
permit ip 10.96.17.0 0.0.0.255 10.0.0.0 0.255.255.255
permit ip 10.96.18.0 0.0.0.255 10.0.0.0 0.255.255.255
permit ip 10.96.0.0 0.0.255.255 192.168.0.0 0.0.255.255
permit ip 10.96.0.0 0.0.255.255 10.0.0.0 0.255.255.255
permit ip 192.168.16.0 0.0.0.255 192.168.0.0 0.0.255.255
permit ip 192.168.17.0 0.0.0.255 192.168.0.0 0.0.255.255
permit ip 192.168.18.0 0.0.0.255 192.168.0.0 0.0.255.255
permit ip 192.168.17.0 0.0.0.255 10.0.0.0 0.255.255.255
permit ip 192.168.18.0 0.0.0.255 10.0.0.0 0.255.255.255
permit ip 172.22.0.0 0.0.255.255 10.0.0.0 0.255.255.255
permit ip 172.22.0.0 0.0.255.255 192.168.0.0 0.0.255.255
route-map NAT-POOL deny 5
match ip address NONAT
route-map NAT-POOL permit 10
match ip address NAT -
I'm on Vodafone, but can't make or receive calls. Viber, messaging and the Internet work fine. I've an iPhone 4. Any ideas?
Did you activate roaming before going abroad?
Click on EE & ME and where it says My Account, click on Devices and Usage and enable it from there, cllick on EE & ME and where it says travel and shopping click on using phone abroad.
http://ee.co.uk/help/add-ons-benefits-and-plans/call-or-going-abroad/roaming---using-your-phone-abroad/using-4g-abroad -
I have a version 1 iPad. I would like to be able to use my LCD projector to display content to my students. I have the dongle to attach to the projector, but can't make it work. The process DOES work with my friend's iPad 2. Any advice? Thanks!
Expanding on what deggie said, with an iPad 1 the app you're using must support video out. Only the iPad 2 can mirror the screen. The apps included with the iPad that output to external monitors are given here:
http://support.apple.com/kb/HT4108
For third-party apps, consult the app's documentation or contact the developer.
Regards. -
I have skype credit but can't make any call (credi...
I have skype credit recently but can't call to any mobile or landphones in my home country India. What ever number I am dialing is ringing but no answer, that means the ringing tone I am hearing is not the actual ringing. I have checked with the person to whom I called through skype, they are saying that they are not getting any call. I have still my skype credit. Kindly help.
I have skype credit but can't make any call
-
My Retina Mac came with 10.8, how can I make a bootable copy of 10.8?
My Retina Mac came with 10.8, how can I make a bootable copy of 10.8?
Do Internet recovery, download the installer, choose an external HD to install it to, when the comp restarts, disconnect the External HD before it turns back on.
Extract the Install.dmg and put it on your desktop, then use disk utility to install that onto your external HD. -
ZTE MF627 My mac version 10.7.2 i can't make connecation
hi guys
i need halp with ZTE MF627 My mac version 10.7.2 i can't make connecation
i put telephone number *99#
account name : username
password : password
after that i got this message
A connection could not be established to the PPP server. Try reconnecting. If the problem continues, verify your settings and contact your Administrator.It looks like you have locked files on the Trash. Follow the steps of this site > http://www.thexlab.com/faqs/trash.html#Anchor-Locked-48213
Maybe you are looking for
-
CUP Provisions user to SAP successfully but gives "Auto-Provisioning" error
Hi All, I'm getting an "auto-provisioning" error in CUP when a "Change Account" workflow is approved. The strange thing is, CUP does successfully provision the change to the SAP backend. Yet, the "New Account" provisions successfully without the erro
-
DataLoad Rule file - Date conversion
Hi, While working on a Dataload rule file,I was facing this problem. I'm getting date in the format "m(m)/d(d)/yyyy hh:mm:ss". Is there a way to change this to "mm/yy" ?? (There won't be anyproblem if I get mm/dd/yyyy hh:mm:ss style. but unfortunatel
-
Network Preferences disappeared in 10.5.8
I just randomly went to check my Network Preferences to restart my wireless internet connection- and it's not there. I'm running OS X Version 10.5.8 and I'm not experiencing any other problems. Under System Preferences > Internet & Network, I have th
-
Hi guys, I wanna buy a 13" MacBook Air with 128 GB SSD, Intel i7 and 8 GB RAM. My question is if I can run smoothly Final Cut Pro X, because I like to do lot of YouTube vids. Thank's for the answer
-
Fld selectn for mvmt type 201 / acct 96220 differs for CO/PP order (011)
Hi all, Purpose : Our client want to use Statistical Internal Order in Movement Type - 201 with entries to be get posted to selective G/L Accounts relating to Vehicle Expenses For that purpose we have made the Order field as "Optional Field" for tra