Mac Edition G5 PCIe ATI Radeon X1900GT 256MB Video Card power cord

I have a G5 2.5 quad, serial number YM5*2EQPS. It has a ATI Radeon 9800 XT on board now. I have two monitors connected.
I want to add a Cintiq graphics tablet, so I need additional video (it is also a monitor). I purchased the Mac Edition G5 PCIe ATI Radeon X1900GT for this purpose.
I can't find a place to plug in the auxiliary power supply. I see several plugs (including a couple centered over the memory slots), but all are filled and none appear to be the six-pin type.
Perhaps I purchased the wrong card for this machine? Or maybe I'm just too stupid to open the back of my computer? Help!
<Edited by Host>

HI-
I am confused by your statements saying that you have a G5 Quad (Late 2005, right?) and that you have a Radeon9800 XT installed.
The 9800 XT is an AGP card and won't work in a Quad...
Putting that aside, the Radeon X1900 G5 Edition connects to the G5 logic board at a connector that is centered on the upper edge of the logic board over the memory slots.

Similar Messages

ATI Radeon X1950 Pro video card and Quicktime Pro

In an earlier thread, I found out that the reason Quicktime Pro was not working on my new computer is that Apple has not yet worked out incompatibilities with QT Pro and new nVidia video cards. Since I need the QT Pro to do my movie editing work, I am going to switch to another high end video card. Does anyone know if an ATI Radeon X1950 Pro video card works with QT Pro? If not, is there another high-end card that someone can recommend?
Thanks

Sounds like you need a bigger case.
Or
External hard drive enclosure to house your drives.

ATI Radeon 9000 Pro video card is conflicting with additional memory

I have a ATI Radeon 9000 Pro video card. I have a 645E Max motherboard (MS-6547). I recently purchased a 512MB dimm of Kingston PC2700 Cas 2.5 memory (KVR333X64C25/512) to go with the the 256MB dimm of the same model # above. I installed the memory and my screen stays blank. When I remove the new dimm it runs fine. I did get the memory and the motherboard tested at the store where I got the motherboard and they work fine. I came to the conclusion it was my video card when I removed all my components except the memory and the video card, and turned on the machine,nothing. I did try swiching dimm location and changing any bios settings I thought would make it work. I tried updating the video card drivers and motherboard AGP drivers. If anybody had this problem in the past could you tell me how you got it to work.

I took the board and the 2 dimms to the store where I bought them. They hooked up both dimms and a video card to the board. When it was powered up, both dimms were recognized. After I got home I proceded to determine if another component it conflicting with the memory. I started with both dimms and my video card the Radeon. I powered up with no other hardware connected and the screen remains blank. I remove the 512MB dimm and leave the 256MB dimm in, and powered up and pc booted up normally.

Where can I find 24" ATI RADEON HD 4850 video card or if there is one compereble to it or dose Aple replaces with new one, because ATI RADEON HD 2600 is deffective and APPLE dose free replacment. Thanks

Where can I find 24" ATI RADEON HD 4850 video card or if there is one compereble to it or does Aple replaces with new one, because ATI RADEON HD 2600 has been recognised as deffective by Apple and APPLE replaces for free. Thanks

http://www.amd.com/us/products/notebook/graphics/Pages/notebook-graphics.aspx is a starting point.

I have a 27" Viewsonic 1080p monitor connected to an oldish Mac Pro with an ATI Radeon X1900 XT Graphics card. The problem is that the image does not fill the screen?!?!?

I know the image can fill the monitor, because at start up, the white Apple logo screen fills it up. But once the system starts up, there are bands of black framing the image. I have searched extensively on the internet and found the following clues, none of which solved the problem:
1) In the Windows world you can get software from ATI called Catalyst Converter that gives you the cpaobility to scale the image. This software/feature is not available for Mac users.
2) Viewsonic's web site has a trouble shooting tool. This came up in response to the topic "you have recently upgraded to a larger monitor"
"This could be an issue if you have an older Apple using the system's onboard memory to support both the system and video display. Even if you have enough onboard RAM to support a higher resolution, it will not since the system will use some of the memory. Because the true video RAM available is much smaller than the total onboard amount, the system limits the size of the image. You will need to contact Apple to get an upgrade in onboard RAM or update the complete system."
I have 2GB of RAM, so lack of RAM memory does not seem to be an issue. I am running OS 10.6.8
Does anyone have any clue how to solve this problem. It is frustrating to have a 27" monitor behaving like a 25" monitor.
Thanks in advance for sharing any experience on this.
JD in PA

http://www.xlr8yourmac.com/Graphics/radeon_X1900XT/X1900XT_dust_buildup.html#sto rytop
http://www.xlr8yourmac.com/Graphics/X1900XT_Overheating/ATI_X1900_artifacts.html
http://www.amazon.com/BUFFERED-PC2-5300-FB-DIMM-APPLE-Memory/dp/B002ORUUAC/
http://www.amazon.com/Apple-ATI-Radeon-5770-MC742ZM/dp/B003Z6QH6M/
http://www.amazon.com/PCIe-Power-Cable-nVidia-Video/dp/B002UR1654/
http://www.amazon.com/gp/product/B0036Q7MV0/

Having trouble with my G4 MDD 867MHz DP and ATi Radeon 9800 Pro video card.

I just recently purchased the ATi Radeon 9800 Pro Mac edition card on ebay. I installed the card on my G4 and turned it on thinking everything would work with no problems, but when I turned it on the grey apple screen came up fine and then it changed to a sky-blue screen with nothing on it and remained on that screen. My desktop or any of my apps did not load up at all. I reset the PRAM and the NVRAM as the seller I bought the card from instructed me to and still I get the same result. Is anyone familiar with this problem? I was wondering if my monitor was the problem because I'm using a Dell LCD monitor as the display for right now? I need help! I'm trying to get this up and running so I can start editing. Whatever information anyone can give me will be greatly appreciated!

Sometimes display cards that support multiple displays (or a second display card in the same Mac) can cause the display you are using to be the SECOND display in a multiple-display "extended desktop".
When this happens, the MenuBar and cursor may be drawn perfectly, but be on the "other" screen, and it is very difficult to determine what has happened. \[This problem is sometimes caused by inadvertently leaving an adapter or cable on an unused display port.]
Try moving the mouse many times to the right to see if the cursor suddenly transitions onto your screen, then try the same experiment to the left.

AE CS6 doesnt recognize my ATI Radeon HD 6850 video card GPU

As in the title, it keeps me saying GPU is not enabled while OpenGL 4.1 is supported. Any suggestions?

The video driver should be correctly updated, i launched just yesterday a quick AMD app to do that.
I dont get what screenshot you want, i dont have any OpenGL preferences in Video Card settings, but i do have put below the screenshot of AE OpenGL preferences, evenif the first part is in Italian.
By the way the productor's specs formy card are (from the site):
AMD Radeon™ HD 6850 GPU Feature Summary:
775MHz Engine Clock
1GB GDDR5 Memory
1000MHz Memory Clock (GDDR5)
128 Gbps memory bandwidth (maximum)
1.5 TFLOPS compute power
Double slot form factor
TeraScale 2 Unified Processing Architecture
960 Stream Processors
48 Texture Units
128 Z/Stencil ROP Units
32 Color ROP Units
PCI Express® 2.1 x16 bus interface
"Eye-Definition" graphics
DirectX® 11 support
Shader Model 5.0
DirectCompute 11
Programmable hardware tessellation unit
Accelerated multi-threading
HDR texture compression
Order-independent transparency
OpenGL 4.1 support
Image quality enhancement technology
Up to 24x multi-sample and super-sample anti-aliasing modes
Adaptive anti-aliasing
Morphological anti-aliasing (MLAA)
16x angle independent anisotropic texture filtering
128-bit floating point HDR rendering
AMD Eyefinity multi-display technology1
Independent resolutions, refresh rates, color controls, and video overlays
Display groupingCombine multiple displays to behave like a single large display
AMD App Acceleration2
AMD Accelerated Parallel Processing (APP) technology3,4
OpenCL 1.1
DirectCompute 11
Accelerated video encoding, transcoding, and upscaling
UVD 3 dedicated video playback accelerator
MPEG-4 AVC/H.264
VC-1
MPEG-2 (SD & HD)
Multi-View Codec (MVC)
MPEG-4 part 2 (DivX, Xvid)
Adobe Flash
Enhanced Video Quality features
Advanced post-processing and scaling
Dynamic contrast enhancement and color correction
Brighter whites processing (Blue Stretch)
Independent video gamma control
Dynamic video range control
Dual-stream HD (1080p) playback support
DXVA 1.0 & 2.0 support
AMD HD3D technology5
Stereoscopic 3D display/glasses support
Blu-ray 3D support
Stereoscopic 3D gaming
3rd party Stereoscopic 3D middleware software support
AMD CrossFireX™ multi-GPU technology6Dual GPU scaling
Cutting-edge integrated display support
DisplayPort 1.2
Max resolution: 2560x1600 per display
Multi-Stream Transport
21.6 Gbps bandwidth
High bit-rate audio
HDMI® (With 3D, Deep Color and x.v.Color™)Max resolution: 1920x1200
Dual-link DVI with HDCPMax resolution: 2560x1600
VGAMax resolution: 2048x1536
Integrated HD audio controller
Output protected high bit rate 7.1 channel surround sound over HDMI or DisplayPort with no additional cables required
Supports AC-3, AAC, Dolby TrueHD and DTS Master Audio formats
AMD PowerPlay™ power management technology4
Dynamic power management with low power idle state
Ultra-low power state support for multi-GPU configurations
AMD Catalyst™ graphics and HD video configuration software
Unified graphics display driversCertified for Windows 7, Windows Vista, and Windows XP
AMD Catalyst Control Center™Software application and user interface for setup, configuration, and accessing special features of AMD Radeon products

Mac Pro 2008 and ATI Radeon HD 5770

According to many other threads in this forum the ATI Radeon HD 5770 graphics card is said to work fine with the Mac Pro 2008 (model no. 3,1) though the Apple Store lists the Mac Pro (Mid 2010) under system requirements. Well, before I’m going to upgrade my Mac against Apple’s will, I’m just curious to know if anyone has found out why Apple restricts the compatibility to Macs from mid 2010 on. Is there an issue that affects only a small number of machines? Or is there a software incompatibility popping up under rare circumstances? What is the reason for this? Why does Apple not grant downward compatibility?

Apple does marketing and doesn't do a bang-up job on writiing technical requirements on hardware upgrades and testing. It doesn't make sense, there is no reason for not just "works with 10.6.5 or later on ALL Mac Pro models."
something nice and clear and so avoids all the questions and discussion.
Radeon HD 5870 versus 5770
2008 has PCIe 2.0 so no lose of bandwidth.
And I guess you ignored the numerous comment section on the product page? where people said it works.
ATI Radeon HD 5770 MC742ZM A

Hello !, can i install Mac OSX Lion to my PC (not mac) i have got Intel Core2 Quad processor and Gigabyte P35-DS3 and 3GB RAM and ATI Radeon HD4850 Sapphire graphics Card ?

Hello Guys
i want to install MacOSX to my pc
i heard something about that (like OSX86 project ?)
i have got Intel Core2 Quad processor and Gigabyte P35-DS3 and 3GB RAM and ATI Radeon HD4850 Sapphire graphics Card ?
please answer .......

Teknus... Here's the issue. For starters, I understand software licensing issues may not be interpreted the same in all countries (although they are still applicable). I also understand that everyone is not familiar with what software licensing is. It is technically possible to install OS X on a PC (as you have seen on your friends computer). However, Apple has designed OS X to only work on Macs. In order to get OS X to work on a PC, it must be modified ("hacked"). As these forums are owned by Apple, we are not permitted to provide you with instructions on how to hack their OS.
Having said that, I have used OS X on PCs. It is not a pleasant experience at all. The experience is actually poor enough on a PC that I would not even use it... opting for Windows or Linux instead. You're simply sacrificing too much of the true OS X experience when you try to run it on standard PC hardware. If you want to try a different operating system, give Linux a try. There are many free versions out there and they will run on just about any PC. The forums are also very helpful. Linux is much more similar to OS X than Windows.
I understand that Macs are expensive and that you would like to use OS X on a PC. The simple fact is that using it on a PC would not be the same as using it on a Mac.

Multiple ATI Radeon HD 2600 XT cards in a Mac Pro

I'm wondering if anyone has any experience with screen spanning with multiple ATI Radeon HD 2600 XT cards. What I'm looking to do is super widescreen presentations with keynote and I need more pixels. Right now I use the Matrox Dual and Triple head to go GXMs to achieve this because they make the computer see multiple monitors as one giant display but I am limited to 3840x1200 (dual 1920x1200) I was wondering if multiple video cards would also see the displays as one giant desktop?
It works on a PC but then I have to use PowerPoint (ugh). Any help or suggestions with this? Thanks in advance.

Multiple graphics cards will make the displays act as one large desktop, but when an application is set to full screen mode, it usually will just use one display. If the application is run in window mode, you should be able to move and enlarge (by dragging the lower-right corner) the window to use all displays, but there will be a window border (and menu bar on one display). You could zoom the display slightly to move the border off-screen. There is a setting in Zoom Options of "Universal Access" system preference to stop the zoomed image from moving unless the pointer reaches an edge.

The AVI Radeon X1900 XT video card in my Mac Pro Dual-Core went bad and I need to replace it. I found one that is $250 but I don't think that I need the gaming-type processor. I am using a 23" Apple Display. Are there lower cost options? -C

The Radeon X1900 XT video card went bad in my Mac Pro Dual-Core Intel Xeon. (I tried it with a good one at the office). I found one online that was $250. I don't need the gaming capacity of this card and was wondering if there were less expensive video cards that I could use in this machine. I run Adobe Creative Suites for graphics design and have a 23" Apply display. Thank you for any help that you can provide. -PretzelMcK

Then pick up the ATI 5770 AND upgrade to 10.6.8.
Same price for a good card that will work and helps to have 1GB VRAM.
There aren't any other real choices let alone less expensive.
Even the ebay links I had and not a lot of choices.

Is FCPX usable with late 2007 Mac Pro's with ATI HD3870 (or OEM graphics cards?

I have a late 2007 Mac Pro with an ATI Radeon HD3870 Mac&PC (3870 ROHS 512mB) graphics card. This card is wupposed to be OpenCL hardware capable. Will it work with FCPX? I'm not aware of any current enhanced graphics cards that will work with that vintage MacPro. I'm currently using FCP7, but has anyone tried this system with FCPX?

nfoo wrote:
According to Apple it is compatible.
Just go ahead and try to buy it: the App Store will detect if your card is compatible and will refuse to let you buy FCPX if it isn't. So there's no risk.
If you want to upgrade your gfx card, the Ati 5770 and 5870 are both compatible with all Mac Pro Models.
Apple says no. The Store says mid 2010 for 5770.
I just got confirmation from someone on the LAFCPUG forum that they have MacPro 1.1 (2006) with 5770 installed and they were able to purchase FCPX.

RADEON 9800 XT 256MB VIDEO CARD

I have a RADEON 9800 XT 256MB VIDEO CARD and when my cpu goes into sleep mode the card has a fan on it and it's still running. I checked if I had any app's still open but I don't except for Dashboard. So how can i get the video card to go into sleep mode?
[email protected]
Dual 2 GHz PowerPC G5 Mac OS X (10.4.8)

offtheroad-
Do you have the CPU and monitor set to go to sleep at the same time?
Luck-
-DaddyPaycheck

RADEON 9800 XT 256MB VIDEO CARD won't sleep

RADEON 9800 XT 256MB VIDEO CARD
Posted: Dec 8, 2006 4:21 AM
Click to reply to this topic Reply email Email
I have a RADEON 9800 XT 256MB VIDEO CARD and when my cpu goes into sleep mode the card has a fan on it and it's still running. I checked if I had any app's still open but I don't except for Dashboard. So how can i get the video card to go into sleep mode?
[email protected]
Dual 2 GHz PowerPC G5 Mac OS X (10.4.8)
Dual 2 GHz PowerPC G5 Mac OS X (10.4.8)

offtheroad-
Do you have the CPU and monitor set to go to sleep at the same time?
Luck-
-DaddyPaycheck

DKA790GX and Visiontek ATI Radeon HD 3870 OCE Cards

Okay I have a MSI DKA790GX motherboard. (MS-7550 v1.21) with latest BIOS 1.9 loaded, a Phenom X4 9550 CPU, 8GB RAM, and 2 Visiontek ATI Radeon HD 3870 OCE Cards.
Without any drivers installed, everything works fine. With both cards in and set up with the crossfire connection installed, you can't even complete the installation of the catalyst drivers without it locking up.
This is in Windows 7 64 bit, and have tried both Ultimate and Professional, just for kicks. With just one card installed, driver installation completes successfully and everything works as normal. With the drivers installed first like this, if I then install the second card i get a blue screen on ATIMKDAG.sys. I have tried switching the order of the cards to verify that each card works by itself.
I have also tried both the latest catalyst 10.2 drivers and the manufacturers drivers which are 9.something
I have the same 2 cards in a K9A2 Platinum running fine on Vista Ultimate 64 and now I am somewhat afraid to update it to Win 7.
About the only thing I haven't tried yet is to do the same setup in a Win 7 32 environment to see if it's any different. but a quad core CPU and 8GB RAM is kind of wasted on a 32 bit OS.
Has anyone had any similar experience with this? I am not sure where the blame is, but I suspect it is in the ATI drivers and not the OS or the motherboard.
I am open to any suggestions.

Quote
About the only thing I haven't tried yet is to do the same setup in a Win 7 32 environment to see if it's any different.
Try it
Quote
MS-7550 v1.21) with latest BIOS 1.9 loaded, a Phenom X4 9550 CPU, 8GB RAM, and 2 Visiontek ATI Radeon HD 3870 OCE Cards.
How much memory sticks? Exact models? In which DIMM's are installed?
PSU? Brand and details?[look for them over PSU sticker]?

Mac Edition G5 PCIe ATI Radeon X1900GT 256MB Video Card power cord

Similar Messages

Maybe you are looking for