MAC Flapping Issue

Dear Folks,
I am working with a IT organization as network administrator, at client site we are getting the MAC FLAPPING issue since 1 month, due to that some time it completely down my whole network. Scenario is like that, we are using Ruckus AP and Zone director as a WLAN controller which is directly conecteted with our core switch. Rest of indoor AP's are connected with Distribute and access switch. Now since 1 month we are getting in core switch below mention notification -
#sh log
Log Buffer (8192 bytes):
889842: Nov 18 13:46:37.182 IST: %SYS-5-CONFIG_I: Configured from console by iympladmin on console
889843: 001585: Nov 18 13:47:09.724 IST: %SW_MATM-4-MACFLAP_NOTIF: Host c4d9.879b.cf99 in vlan 13 is flapping between port Gi1/1/4 and port Gi1/1/3 (nhcin-sjp01-2)
889844: Nov 18 13:49:17.806 IST: %LINK-3-UPDOWN: Interface GigabitEthernet2/0/37, changed state to up
889845: Nov 18 13:49:19.818 IST: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet2/0/37, changed state to up
889846: 001586: Nov 18 14:04:57.394 IST: %SW_MATM-4-MACFLAP_NOTIF: Host c4d9.87aa.d584 in vlan 13 is flapping between port Gi2/0/41 and port Gi2/0/35 (nhcin-sjp01-2)
889847: 001587: Nov 18 14:13:39.784 IST: %SW_MATM-4-MACFLAP_NOTIF: Host 0008.2292.1440 in vlan 12 is flapping between port Gi2/1/2 and port Gi1/1/4 (nhcin-sjp01-2)
889848: 001588: Nov 18 14:15:35.735 IST: %SW_MATM-4-MACFLAP_NOTIF: Host 1c3e.843e.c441 in vlan 13 is flapping between port Gi2/0/41 and port Gi2/0/35 (nhcin-sjp01-2)
889849: Nov 18 14:23:23.346 IST: %SW_MATM-4-MACFLAP_NOTIF: Host 14f6.5afa.ecb9 in vlan 12 is flapping between port Gi2/0/37 and port Gi2/0/35
889850: 001589: Nov 18 14:23:23.415 IST: %SW_MATM-4-MACFLAP_NOTIF: Host 14f6.5afa.ecb9 in vlan 12 is flapping between port Gi2/0/37 and port Gi2/0/35 (nhcin-sjp01-2)
889851: Nov 18 14:32:33.860 IST: %SW_MATM-4-MACFLAP_NOTIF: Host c0cb.3886.30cb in vlan 13 is flapping between port Gi2/0/41 and port Gi2/0/35
889852: 001590: Nov 18 14:32:33.954 IST: %SW_MATM-4-MACFLAP_NOTIF: Host c0cb.3886.30cb in vlan 13 is flapping between port Gi2/0/41 and port Gi2/0/35 (nhcin-sjp01-2)
889853: 001591: Nov 18 14:33:05.755 IST: %SW_MATM-4-MACFLAP_NOTIF: Host 843a.4b15.187a in vlan 12 is flapping between port Gi2/0/41 and port Gi2/0/35 (nhcin-sjp01-2)
889854: 001592: Nov 18 14:33:07.017 IST: %SW_MATM-4-MACFLAP_NOTIF: Host 6c88.14a0.93d8 in vlan 12 is flapping between port Gi2/0/41 and port Gi2/0/35 (nhcin-sjp01-2)
nhcin-sjp01#
As mentioned in msg 12 & 13 VLAN is our WLAN.
After getting this msg automatically all network goes down, I need to shut down the associated port winch is directly or indirectly connected with AP, and after some time it will work properly.
Now I need some mechanism which can be block the duplicate source mac address to preventing from this kind of scenario.
Regards,
Shekhar

Hi Devils,
Answer is in below -
1. Are those MAC addresses actual Wireless Hosts? i.e have you traced them?
= Yes, those are actual wireless MAC add, I have check in zone director controller.
2. Are the SSID's set to tunnel?
=No
3. Do you have one ZoneDirector or two?
=Two, both of them are connected with core switch.
I have been confirmed about that if wireless users are roaming between two AP or more it will appear the same error msg, now what would be the solution. ????
What extly the solution is?>
Where should i implement the solution on switch or zone director?
Please suggest!!!!!

Similar Messages

Mac-flap issue

Hi,
I have 16 switches and 3 servers in my network.In server room,i have one cisco WS-C2960S-48TS-L and one WS-C2960S-24TS-L connected to each other.Two eth ports of each server are being timmed and connected to the 2 switches.Every thing is fine but i am getting mac-flap log in both switches.can anyone tell me how can i stop this?
48TS-L is the root bridge of the network and there is only 1 vlan in the network.all the ports are in same vlan of both switches.
here is a sample of the logs of both siwitches :-
*Feb 1 08:24:28.382: %SW_MATM-4-MACFLAP_NOTIF: Host 0015.5d07.1903 in vlan 101 is flapping between port Gi1/0/48 and port Gi1/0/3
*Feb 1 08:26:34.992: %SW_MATM-4-MACFLAP_NOTIF: Host 0015.5d07.1e01 in vlan 101 is flapping between port Gi1/0/48 and port Gi1/0/6
*Feb 1 08:25:40.351: %SW_MATM-4-MACFLAP_NOTIF: Host 0015.5d07.1e05 in vlan 101 is flapping between port Gi1/0/24 and port Gi1/0/15
Thanks in advance.

Hello
It occurs when you have a loop between the switches relating to ports bypassing the stp process and enter forwarding state either due stp being turned off or having portfast enabled.
when you have a server connectiing itself to two switches on portfast enabled ports, this can cause this type of issue you are seeing- Check if this is the case and disable the portfast feature on those ports
For trunk ports or if port aggregation check the link negotiation type (usually LACP for servers) is applied the same on both sides of the etherchannel and teamed server nics
res
Paul
Please don't forget to rate any posts that have been helpful.
Thanks.

Large amount of traffic with 152x mesh and mac-flap

We have just had a Mesh designed by an external company, and when we plugged it in we began have large numbers of mac-flap notification and more than 700mb of traffic sent across our data network.
Our setup includes 2 5508 controllers and 9 152x APs
3 APs (RAP) with their 5.8 antennas are within close proximity on a vertical pole pointing to the other 6 about 1000mtrs away in an arc. With their ethernet ports plugged into the same switch (native vlan 111) as WLC1 (which is LAG'd to two ports)
Vlan 111 for management of Mesh
Vlan 201 for WLAN
DHCP scope on DC on Vlan 100 (helper address from router)
Q, will the closeness of the 5.8 antennas cause any problems with mac-flap or is likely to be the controllers with their LAG connections or something totally different?
Thanks for any help

Andrew,
the proximity of the antennas shouldn't cause the mac-flap notification, nor should the LAG connection cause this. That's more and indication that the client is flopping between ports on the switch, which generally happens when you are not configured for LAG on the WLC, nor a port-channel on the switch.
the mac address that is being reported in the mac-flap. Is it a client or is it the MAPs?
If it's one of hte MAPs, you may want to check the antennas of the RAPs, since the MAPs sholdl stabliaze once AWPP has run and optimized the path to the network. If they are flapping I would look at possible RF or antenna issues.
HTH,
Steve
Please remember to rate helpful posts or to mark the question as answered so that it can be found later.

Mac flap

Hello,
I came across an issue with and cisco 1841 fa0/1 plug into a 8 port cisco switch (G0/1)
there are 3 sub ifs on the router
10
20
30
I keep getting mac flap between GIG0/1 the uplink to the router and f0/1 which is in access mode and faces the customer.
The mac in question was the BIA of fa0/1 I don't understand how this can happen spanning tree is enabled portfast is not enabled
any idea's?

Hi,
May be I missed something here in your description.
Your router fas0/1 has sub interfaces
Your switch gig0/1 is in access mode ???
If you are using sub interfaces on your router then to me the switch port should be in trunk mode
something like this:-
ROUTER
int fas0/1
desc ** TRUNK TO SWITCH **
duplex auto
speed auto
int fas 0/1.10
desc ** VLAN 10 ***
encapsulation dot1Q 10
ip address 10.0.10.254 255.255.255.0
no ip redirects
no ip unreachables
int fas 0/1.20
desc ** VLAN 20 ***
encapsulation dot1Q 20
ip address 10.0.20.254 255.255.255.0
no ip redirects
no ip unreachables
int fas 0/1.30
desc ** VLAN 30 ***
encapsulation dot1Q 30
ip address 10.0.30.254 255.255.255.0
no ip redirects
no ip unreachables
SWITCH
int gig0/1
desc ** TRUNK TO SWITCH **
speed auto
duplex auto
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 10,20,30
switchport mode trunk
Regards
Alex

MAC-flap Notifications

I am having an issue at one of our remote agencies whereas we are getting numerous mac-flap notifications on our switches.   This has become kind of a hinderance as we are getting tired of seeing these messages.   The end users havent been complaining, but the log messages are annoying.
It's usually occurring with the same mac-addresses over and over.   Upon further investigation, we found the mac-addresses are all on laptops which have both wireless and wired nic's.    There are wireless AP's (cisco 1242's) in use which they can connect. We also found where the error is popping up as they move from wireless into docking into their docking station which has a lan cable attached.    I was under the assumption that the wireless mac and wired mac were different numbers and therefore if the wired was up simultaneously with the wired, as it switched over, they shouldn't get a flap.
How can I correct this....or is it correctable?
I have attached a diagram to show my scenario, keep in mind those are just a few of the MANY msg's we have been receiving.   If anyone
can explain this to me, I'd appreciate it.

jonesl1 wrote:I am having an issue at one of our remote agencies whereas we are getting numerous mac-flap notifications on our switches.   This has become kind of a hinderance as we are getting tired of seeing these messages.   The end users havent been complaining, but the log messages are annoying. It's usually occurring with the same mac-addresses over and over.   Upon further investigation, we found the mac-addresses are all on laptops which have both wireless and wired nic's.    There are wireless AP's (cisco 1242's) in use which they can connect. We also found where the error is popping up as they move from wireless into docking into their docking station which has a lan cable attached.    I was under the assumption that the wireless mac and wired mac were different numbers and therefore if the wired was up simultaneously with the wired, as it switched over, they shouldn't get a flap.    How can I correct this....or is it correctable?I have attached a diagram to show my scenario, keep in mind those are just a few of the MANY msg's we have been receiving.   If anyonecan explain this to me, I'd appreciate it.
Are the users with these laptops roaming wirelessly across floors ie. could they be connected on bottom floor before then going back to floor 2, for example, where their wired connection is ?
Jon

Mac Enrollment Issue on SCCM 2012 SP1

Hi Guys,
I am working on Mac enrollment(10.7) and facing issue during enrollment. Below is the error message when we try to run the enrollment command on Mac :
“Server connection failed. HTTP Response code is 500 and reason is Internal Server Error"
Below are Log info:
Enrollsrv.log : No error message is highlighted.
Enrollweb.log:
No error message is highlighted.
Enrollservice.log:
[7, PID:7304][10/28/2013 16:40:03] :ConfigManager: ChainStatus error: RevocationStatusUnknown,The revocation function was unable to check revocation for the certificate.
;OfflineRevocation,The revocation function was unable to check revocation because the revocation server was offline.
   at Microsoft.ConfigurationManagement.Enrollment.ConfigManager.SplitCACertChain(String base64cert)
   at Microsoft.ConfigurationManagement.Enrollment.ConfigManager.setCAChain(EnrollmentServiceProfile profile, WindowsIdentity requester)
   at Microsoft.ConfigurationManagement.Enrollment.ConfigManager.RefreshCache(Int32 enrollmentProfileId, EnrollmentRecordType type, String template, WindowsIdentity requester)
   at Microsoft.ConfigurationManagement.Enrollment.RequestHandler.ProcessRequestSecurityToken(RequestSecurityTokenType request, WindowsIdentity caller, ActionEnum action)
   at Microsoft.ConfigurationManagement.Enrollment.RequestHandler.EnrollDevice(Message messageRequest)
   at Microsoft.ConfigurationManagement.Enrollment.DeviceEnrollmentService.RequestSecurityToken(Message messageRequest)
[7, PID:7304][10/28/2013 16:40:03] :FaultCode is: EnrollmentServer and reason is: EnrollmentServerException InitializeFailed
[13, PID:7304][10/28/2013 17:11:01] :EnrollmentService application stop ...
[3, PID:956][10/28/2013 17:45:37] :EnrollmentService application start ...
[3, PID:956][10/28/2013 18:06:38] :EnrollmentService application stop ...
[3, PID:4700][10/28/2013 18:45:39] :EnrollmentService application start ...
[7, PID:4700][10/28/2013 19:06:40] :EnrollmentService application stop ...
[3, PID:5872][10/28/2013 19:45:42] :EnrollmentService application start ...
[13, PID:5872][10/28/2013 20:06:42] :EnrollmentService application stop ...
Can someone shed info on resolution of the above issue?
Also, is there any means by which we can troubleshoot the Mac enrollment issue step by step? Also what entries needs to be checked in all logs for successful enrollment?

the following links may give you some hints:
http://social.technet.microsoft.com/Forums/en-US/48bc7fcc-3d84-4042-abac-67f30d701121/mac-enrollment-issue?forum=configmanagerdeployment
http://www.windows-noob.com/forums/index.php?/topic/7391-mac-enrollment-issue/

Mac System Issue pop up window has disabled Safari. Please help?

I clicked on a video on FaceBook & ended up with a pop up that says I have a serious Mac system issue & I need to call this phone number immediately.
I can't do anything at all with Safari now. Has anyone had this issue? Know how to get rid of it? I

Force quit Safari and relaunch it with the Shift key held down. If that doesn’t work, disconnect the computer from the Internet and try again.
(115087)

MAC flapping

Hi,
I have a problem with MAC flapping on one of my switches. I didn't setup that environment and I founded that recently. I think person which was in company before made there mistake with configuration.
Below here is a picture how it is connected. Basically from server to switch there is 2 cables going and they are using the samne VLAN.
On the picture I pasted config of switchports and output from syslog.
What I'm thinking is to make this two switchport in one EtherChannel using channel-group command. What do You think ??
Best Regards, Jacek

Well, I think that etherchannel with "mode on" should work in this kind of environment...give it a try. Also, check on this link if everything about bonding is OK with your linux:
http://www.charleshooper.net/blog/link-aggregation-on-a-redhat-centos-server-and-a-cisco-catalyst-switch
It's for CentOS but I suppose it's similar for every other Linux...
I suppose you know how to configure etherchannel on Cisco side...
HTH,
Dragan

MAC flapping on WLC ports

Hi all,
I've been getting
.Feb 23 10:59:50: %C4K_EBM-4-HOSTFLAPPING: Host 7C:E9:D3:9A:DC:99 in vlan 1 is flapping between port Gi3/2 and port Fa4/14
.Feb 23 11:00:01: %C4K_EBM-4-HOSTFLAPPING: Host B8:EE:65:71:55:12 in vlan 1 is flapping between port Fa4/14 and port Gi3/2
.Feb 23 11:01:14: %C4K_EBM-4-HOSTFLAPPING: Host 18:CF:5E:FD:41:B8 in vlan 1 is flapping between port Gi3/2 and port Fa4/14
entries on my core switch.
I get the same error for different MACs but always the same 2 ports - Gi3/2 and Fa4/14
The topology looks like this:
both WLC are connected to the same core switch:
Core 2 has WLC-2 connected to Gi 3/2 and Core 2 has C2960S connected to Fa4/14, C2960S has WLC-1 connected to Gig 0/24
Any idea on why the WLC links are showing MAC Flaps?
thanks for the support,

Hi mgonzalez15,
MAC flapping logs within a wireless environment is an expected behavior. The reason of these messages is that wireless hosts (as opposed to wired hosts) are able to roam and can be connecting to other APs/WLCs across your campus in matter of seconds.
HTH,
Julio

MAC address issue----Spearman

Saw your comments on this in the post about the 1.9 bios for neo2platty ....
I can confirm that My MAC address issue was caused by the bios that you sited in your comments....all F's were written to My nvidia lan too...
only solution from what I have read is too rma it...'bummer'
just thought You would like to know.... Your not alone

I had the same problem yesterday and after many hours searching the web I ended up with this post that made me really desperate... But I didn't give up and while trying a new bios flash because of random crashes when in the bios, I noticed the obvious: you can change the MAC address when flashing
use the last version of the dos flasher with the parameters /nvmac:xxxxxxxxxxxx/wb after the name of the bios file; it's explained if you ask the help with the /help parameter. You can find the mac address on a stick on the parallel port.

Thanks bazzardl. I was able to get the MAC Mail issue resolved. Best, glofromkc

Thanks bazzardl. I was able to get the MAC Mail issue resolved. Best, glofromkc

I am having the same problem but cannot get anything but the actual phone to work. I have a unlocked 3GS running 6.0 (what was I thinking?). No data whatsoever, no texting, no visual voicemail. I simply cannot access the APN settings. I have tried sim swap, I have tried APN changers. I have been on the phone with ST tech support for hours and hours. I have tried to get the answers from a "genius". I am stuck and looking at Android devices, but would really like to keep using the iphone with Straight Talk.

Penryn Macs having issues?

Okay,
I have finally decided to move to Mac OS and buy a MacBook Pro.
* iWork '08 preinstalled
* Accessory Kit
* MacBook Pro 15-inch Widescreen Display
* 2.4GHz Intel Core 2 Duo
* 200GB Serial ATA Drive @ 7200 rpm
* Backlit Keyboard/Mac OS - U.S. English
* SuperDrive 8x (DVD±R DL/DVD±RW/CD-RW)
* 2GB 667MHz DDR2 SDRAM - 2x1GB
* Apple Remote
* NVIDIA GeForce 8600M GT with 256MB
I am extremely exited. But before i order, i was wondering if I should expect allot of problems? About 2 years ago, my friend bought a macbook and had to have it replaced 5 times. How have the Penryn macs been?
This will l be my first Mac ever so I am hoping to have a good transition to the mac world:)
Thanks,
Mac Zac.

Hi Zac.
Let me be the first to say, welcome to the light side!
Regarding the Penryn Macs: No, there are not so many issues that you should hold off buying one. If you browse the forums here you'll find lots of people running into problems. But remember that all the millions of people that DON'T have problems don't come here to tell you everything's working fine. For the vast majority of people, Macs work seamlessly, day in and day out.
Of course, like all technology products, sometimes Macs have issues. They are made out of the same silicon and chips as other computers and, like those other computers, components can fail or go bad. That's just life. The good news is: it's rare.
Likewise, Leopard is running extremely well for the vast majority of people. To be sure, there are a few small issues affecting small groups of people. Some folks are having wireless troubles, others are seeing some typing issues after a keyboard firmware update, for some folks iTunes is locking up while browsing cover flow. But, again, these issues don't appear to be too widespread and I would certainly not hold off buying a Mac because of them. You can bet that Apple engineers are all over the issues and they'll be resolved soon.
To sum up: the state of the Mac world is fantastic. Like everything else in life, it's not perfect. But it's as close as you'll get with a computer! My advice is to pull the trigger and enjoy the switch! And I'll put my money where my mouth is as well: my $3,000 Penryn MacBook Pro arrives tomorrow morning.

Error message of MAC flapping for CCM-UC installed in UCS server

Dear All,
I have a strange issue, I have the 2 UCS servers setup with CCM & unity Connection running on each server on PUB - SUB mode.
I'm getting following error message on the Switch where the UCS server Connects.
I'm unable to trace why we are getting this error message, There is no problem with accessing CCM or UC, also the Phone & Voice mail seem to working.
un 25 13:15:14.853: %SW_MATM-4-MACFLAP_NOTIF: Host 000c.2911.db00 in vlan 410 is flapping between port Gi1/0/34 and port Gi1/0/33
Jun 25 13:15:28.828: %SW_MATM-4-MACFLAP_NOTIF: Host 000c.2911.db00 in vlan 410 is flapping between port Gi1/0/34 and port Gi1/0/33
Jun 25 13:15:44.145: %SW_MATM-4-MACFLAP_NOTIF: Host 000c.2911.db00 in vlan 410 is flapping between port Gi1/0/34 and port Gi1/0/33
Has anybody expereinced such error before, Appreciate your help in tracing this error.
Thanks,
Oliver

Hello,
I believe you'll get better answer at:
"https://supportforums.cisco.com/search.jspa?peopleEnabled=true&userID=&containerType=14&container=2003&spotlight=true&q=UCS"
my best guess is to check the LAN config on the UCS. It seems its trying to load balance the traffic in Active-Active rather than Active-Standby.
HTH

Spanning Tree and Admin mac address issues srw2048

Ok, I have a somewhat complex problem and hopefully someone may shed some light or have an idea as to whats wrong.
First the scenario:
I have two Cisco Cat 6509's etherchanneled to each other via two fiber cables. One of these is the STP/RSTP root. I have two SRW2048's.. one trunked to each of these 6509 switches. There is also a trunk between the SRW2048's. All this is to create a redundant topology so that if one of the switches fail's the others can still forward packets to each other. Of course the scenario described is in fact a loop that should be handled by STP/RSTP. I have RSTP enabled on all the switches in the scenario (PV RSTP on the cisco switches as they only do Cisco's brand of per vlan spanning tree). There are 3 vlan's configured on each of the srw2048's (2,55,96). There are corresponding vlan's also on the 6509's. I have put the srw2048's management interface into vlan 2.
The problem:
I need to forward packets between the srw2048's primarily and only use the 6509 that is not the root when a failure happens. I have configured the non-root 6509's spanning tree cost on the etherchannel to be higher then the alternate path through the srw's to the root. I can hook everything up and view the spanning tree and see that the srw2048's interface that goes to the non-root 6509 is blocked, and all other interfaces on the other switches are forwarding. I can in fact ping and get to the admin interface on all the switches. Then for some strange reason the admin interface of the srw2048 plugged into the non-root 6509 stops responding. If I disable either the interface its plugged into on the 6509 or the other srw2048 everything starts working again. Sometimes it responds after many failures for no apparent reason. I looked into the mac-address table on the 6509's and they are conflicting, pointing to each other for the mac-address of the broken srw2048. When I clear the mac-table the admin port comes back for about 5 seconds then again goes dark. When reviewing mac-table on the 6509's they are back to pointing to each other. The odd thing (although I haven't confirmed this completely) is that hosts placed into vlan 2 on that same srw2048 seem to work fine. If there was an STP loop or something misconfigured, I would expect it to effect any host in vlan 2 or the other vlan's for that matter on the srw2048 that stops responding. Alas, I am stuck because I need to manage this switch remotely. My only thought is that for some reason even when the STP status is blocked the broken srw2048 is still sending out arp's of its admin interface and bypassing the STP protocol. I have no way to confirm this, but maybe someone has an idea as to what I'm doing wrong, or otherwise offer a solution. For now, I simply removed vlan 2 from the 6509 that the broken srw2048 is plugged into and everything seems fine.
My apologies for such a long post, but this is somewhat complicated. Thanks in advance for any info.
-Geoff
Message Edited by gmyers on 08-19-2008 10:35 PM

To follow up, I had a ticket open with Linksys about this for about 3 months with no resolution. I submitted packet captures, stp outputs, etc and no luck. I gave up and basically had to revert to a manual failover for redundancy. It's no perfect or fast, but it works every time.
Unless linksys issues a firmware upgrade with this as a fix, I doubt we will be able to ever resolve this on our own.

Outlook 2011 for Mac / Synching issues

Hi there,
it seems that I'm not alone with 'issues' in synching Outlook for Mac 2011 with mobile devices..
The setup I am trying to arm wrestle into submission is
MacBook Air (brand new) Mavericks 10.9.3
iPhone 5 iOS 7.1.1.
Outlook 2013 (brand new)
I've been able to succesfully import all of my email (from a previous version in windows) as well as get the contacts and the calendars imported onto Outlook for Mac, but am at my wits end to get them all talking to each other.
Outlook won't sync to the iPhone for mail, contacts and or calendar, nor visa versa.
I've read literally thousands of posts all suggesting this fix and that fix to no avail. I'm now reading that perhaps mavericks is not compatible with outlook synching services or outlook synching services isn't compatible with mavericks. I'm not trying to lay blame to either side as I'm simply looking for a solution.
Any ideas?
Thanks,
Paul
oh - Apple Migration Tool.... is appalling in my opinion, it did sweet bugger all.

Minor correction. It's Outlook 2011, Outlook 2013 is the Windows version.
Sync Basics
CalDAV & CardDAV are protocols used by Apple, Google, Yahoo and others to sync contacts and calendars. Neither Entourage 2008 nor Outlook 2011 support CalDAV or CardDAV.
You can no longer sync with any third-party apps running on your Mac that use Sync Services, like Entourage or Outlook.
If you want to stick with Outlook, I suggest you look at Office 365 Exchange. Otherwise, moving to Apple Mail, Contacts and Calendar with iCloud might be a better option for you.
Until Microsoft adds CalDAV and CardDAV support to Outlook, there is no way to sync other than get an Exchange account. It's $4/month Exchange Online.
http://office.microsoft.com/en-us/exchange/microsoft-exchange-online-email-for-b usiness-FX103739072.aspx

MAC Flapping Issue

Similar Messages

Maybe you are looking for