Mac G3 w/ Tiger 10.4.3 update problem/issue "digital signature incorrect"

I have an old G3 on which I reloaded 10.4.3 yesterday (Retail copy). It did not go very smoothly. This is the 3rd install; 1st install was several months ago with this chip, 2nd install was shortly after that with a PowerLogix chip which didn't work. I put the old chip/processor back in yesterday and reinstalled again. I don't remember if I messed with the firmware or not with the previous installs.
PowerMacG3, Model 1.1, PowerPC750, 256meg, BootRom 1.1.1f4
The software updater tells me I need to update to 10.4.8. When I proceed with this, the system downloads the software OK, but when it attempts to install the update I get the following error:
The update "Mac OS X Update Combined (PowerPC) can't be installed.
The digital signature for this package is incorrect.
The package may have been tampered with or corrupted since being signed by "Apple".
Any ideas as to how I resolve this? Could the problem be with the OS registration, and the different chips?
Thanks in advance.
PowerMac G3 Mac OS X (10.4.3)
PowerMac G3 Mac OS X (10.4.3)

Thank you for replying to my post.
Yes, I can do a nozzle check with the USB unplugged,
and I still get poor results on the C82 and nothing
on the C86. I just can't believe both printers are
broken. The C86 is new, and they were both working
fine previously.
Epsons are notorious for getting their print heads clogged. Run the clean print head routine a few times. If that doesn't work, return the new printer 'cause it's dead out of the box. The old printer, well, once Epson print heads get to a certain level of clogging, nothing will unclog them. Toss the printer and get a new one. Hint: HP and (some) Canon printers put the print heads in the ink cartridges, while Epson and (some) Canons have the print heads in the printers. Machines which have the heads in the carts also have an easy fix for severe clogs: toss the cart. Warning: HP printer drivers stink.
If you don't need colour, you might think seriously about getting a low-end laser.
I just got the C82 to print readably, but still
completely missing magenta and with minimal
fuzziness. This was just dumb luck though, from
letting the printer sit idle for several hours.
It's still clogged. Clean the heads a few times again, or just toss it.
And yes, I've tried setups through the Print & Fax
pref pane, which usually works better than going
through the Printer Setup Utility which tends to
freeze and crash.
I wish I could afford to just buy another printer.
But I'm still worried it's something to do with my
computer, since both printers are having problems
simultaneously, and they're both really good
all-purpose printers.
It's not your machine. It's Epson.
Dual 2.3 GHz Power Mac G5 Mac OS X
(10.4.3)
Dual
2.3 GHz Power Mac G5 Mac OS X (10.4.2)
Dual 2.3 GHz
Power Mac G5 Mac OS X (10.4.3)

Similar Messages

Adobe AIR update has no digital signature. Is this normal?

I installed Adobe Air and it says it needs to update. But when I click Update, my firewall says there is no digital signature. So, I don't kow if this Adobe product is OK.
Every time, when I surf the Web, I get an Update Adobe message. I don't know if I should update. Last time I did, my computer crashed. It keeps crashing now every 45 minutes. This is why I tried to update Adobe to start with.
Thank you in advance for any help in dealing with this Adobe update with no digital signature.

This seems to be the case, as the two products are developed by the same team.

Mac OS 10.5.8 update combined can't be saved, Apple digital signature incorrect.

Hi,
I have tried, several times, to update OS 10.5.1 to 10.5.8 using Apple's online software updater. It takes 20 minutes to download the 768 mb package but then
refuses to save with the following message. 2.16 GHz + 2 GB ram.
Mac OS X can't be saved. The digital signature for this package is incorrect. The package may have been tampered with or corrupted since being signed by Apple.
I need to update to 10.5.8 so I can then install 10.6 etc.
I have tried to install 10.6 without updating to 10.8 but it shows the message: Mac OS X can't install on this computer. I assume this is because I have not, and
cannot, updated to 10.5.8.
Any help would be appreciated.
Apple want me to pay $20 to advise them that their software package has an incorrect digital signature, even though it has only just been downloaded from their servers. No email address to advise Apple of problem.

Hello, it's generally one of two thinks that cause this, but it is a bad download.
Try Ethernet instead of Airport if possible.
Disk can be corrupted...
Safe Boot, (holding Shift key down at bootup), run Disk Utility in Applications>Utilities, then highlight your drive, click on Repair Permissions, reboot when it completes.
(Safe boot may stay on the gray radian for a long time, let it go, it's trying to repair the Hard Drive.)
Try getting it direct instead of SWUPDate...
Repair Permissions afterwords, reboot.
1058 Combo Update, 10.5.8...
http://support.apple.com/downloads/Mac_OS_X_10_5_8_Combo_Update

Security Update 2009-004 Digital Signature failure

Recently prompted to install this update "Security Update 2009-004 (Intel)" so I initiated install only to get a pop up after a few mins saying:
*The update "Security Update 2009-004 (Intel)" can't be installed.*
The digital signature for this package is incorrect. The package may have been tampered with or corrupted since being signed by "Apple".
Anyone know what this slightly worrying message means and any advice on what to do next? I've read elsewhere that the security update isn't really necessary for my situation (being a simple macbook user) but more concerned about the tampered and or corrupted aspect of the message.
Should I be worried readers?

Hi BucksFraz, and a warm welcome to the forums!
Could be many things, we should start with this...
"Try Disk Utility
1. Insert the Tiger Mac OS X Install disc that came with your computer, then restart the computer while holding the C key.
2. When your computer finishes starting up from the disc, choose Disk Utility from the Installer menu. (In Mac OS X 10.4 or later, you must select your language first.)
Important: Do not click Continue in the first screen of the Installer. If you do, you must restart from the disc again to access Disk Utility.
3. Click the First Aid tab.
4. Select your Mac OS X volume.
5. Click Repair. Disk Utility checks and repairs the disk."
http://docs.info.apple.com/article.html?artnum=106214
Then Safe Boot , (holding Shift key down at bootup), run Disk Utility in Applications>Utilities, then highlight your drive, click on Repair Permissions, reboot when it finishes.
The usual reason why updates fail or mess things up, or things don't load/run, is if Permissions are not fixed before & after every update, with a reboot... you may get a partial update when the installer finds it doesn't have Permissions to change one obscure little part of the OS, leaving you with a mix of OS versions.
Some people get away without Repairing Permissions for years, some for only days.
If Permissions are wrong before applying an update, you could get mixed OS versions, if Directory is the slightest messed up, who knows!
If many Permission are repaired, or any Directory errors are found, you may need to re-apply some the latest/biggest updates again, or even do an A&I if you have enough free disk space.
The combo update for PowerPC-based Macs...
http://www.apple.com/support/downloads/macosx10411comboupdateppc.html
The combo update for Intel-based Macs...
http://www.apple.com/support/downloads/macosx10411comboupdateintel.html
Repair Permissions before & after re-install, then reboot again each time.
If all the above fails, then it appears to be time for a relatively painless Archive & Install, which gives you a new/old OS, but can preserve all your files, pics, music, settings, etc., as long as you have plenty of free disk space and no Disk corruption, and is relatively quick & painless...
http://docs.info.apple.com/article.html?artnum=107120
Just be sure to select Preserve Users & Settings.
I only use Software Update to see what is needed, then get them for real via...
http://www.apple.com/support/downloads/
That way I can wait a week or so, check the forums for potential problems, and get Permissions & such in order before installing.

Software Update - digital signature incorrect

I have several update packages that were consistently reporting the error:
*The update "xxxxxxx" can't be saved.*
The digital signature for this package is incorrect.
The updates are:
iLife Support 9.0.3
Java for Mac OS X 10.5 Update 4 1.0
Safari 4.0
Several other updates (eg. recent iTunes and QuickTime) downloaded and installed OK.
I tried all of the following to no avail:
Repair disk permissions
Reinstall 10.5.7 combo package manually
Delete Software Update preferences & cache files
Multiple restarts
Finally I tried running Software Update under a fresh admin account and they downloaded OK. (Different issue that the Java Update later said it couldn't install).
So seemingly this is related to something in my usual admin account. Does anybody know what other preference files I should look to delete, or any other hidden setting that is affecting the digital signature checking?

I tried all of the following to no avail:
Repair disk permissions
Guess Carolyn didn't notice this.
This was happening fairly frequently about a month ago when 10.5.7 came out. The Apple servers were overloaded apparently and some incomplete downloads occurred so some type of checksum prevented running the update. Waiting and downloading later seemed to be the best solution.
http://discussions.apple.com/thread.jspa?messageID=9456350&#9456350
So seemingly this is related to something in my usual admin account. Does anybody know what other preference files I should look to delete, or any other hidden setting that is affecting the digital signature checking?
Perhaps by the time you did all the troubleshooting steps, if you tried it from the original admin account it would have downloaded correctly.

Mac OS X 10.5.2 software update problem?

<h3 style="font-size: 146.5%; font-weight: bold; color: #000000; line-height: 1.1; margin-bottom: 8px;" mcestyle="font-size: 146.5%; font-weight: bold; color: #000000; line-height: 1.1; margin-bottom: 8px;"><span style="color: #333333; font-size: 13px; font-weight: normal; line-height: normal;" mcestyle="color: #333333; font-size: 13px; font-weight: normal; line-height: normal;">Okay, so I tried updating my iTunes to 10.5.1. It downloaded and all, but the iTunes itself won't open anymore. When I click it, it says: http://i40.tinypic.com/v7z6t4.png (please click to show image). I don't understand what I have to do. Someone please explain to me, thank you. _

Some general advice on updating:
It is worth noting that it is an extreme rarity for updates to cause upsets to your system, as they have all been extensively beta-tested, but they may well reveal pre-existing ones, particularly those of which you may have been unaware. If you are actually aware of any glitches, make sure they are fixed before proceeding further.
So before you do anything else:
If you can, make a full backup first to an external hard disk. Ideally you should always have a bootable clone of your system that enables you to revert to the previous pre-update state.
Turn off sleep mode for both screen and hard disk.
Disconnect all peripherals except your keyboard and mouse.
1. Repair Permissions (in Disk Utility)
2. Verify the state of your hard disk using Disk Utility. If any faults are reported, restart from your install disk (holding down the C key), go to Disk Utility, and repair your startup disk. Restart again to get back to your startup disk.
At least you can now be reasonably certain that your system does not contain any obvious faults that might cause an update/upgrade to fail.
3. Download the correct version of the COMBO update from the Apple download site.
The Combo updater of Leopard 10.5.8 can be found here:
http://support.apple.com/downloads/Mac_OS_X_10_5_8_Combo_Update
If you prefer to download updates via Software Update in the Apple menu (which would ensure that the correct version for your Mac was being downloaded), it is not recommended to allow SU to install major (or even minor) updates automatically. Set Software Update to just download the updater without immediately installing it. There is always the possibility that the combined download and install (which can be a lengthy process) might be interrupted by a power outage or your cat walking across the keyboard, and an interrupted install will almost certainly cause havoc. Once it is downloaded, you can install at a time that suits you. You should make a backup copy of the updater on a CD in case you ever need a reinstall.
Full details about the 10.5.8 update here: http://support.apple.com/kb/HT3606
More information on using Software Updater here:
http://support.apple.com/kb/TA24901?viewlocale=en_US
Using the Combo updater ensures that all system files changed since the original 10.5.0 are included, and any that may have been missed out or subsequently damaged will be repaired. The Delta updater, although a temptingly smaller download, only takes you from the previous version to the new one, i.e. for example from 10.5.7 to 10.5.8. Software Update will generally download the Delta updater only. The preferable Combo updater needs to be downloaded from Apple's download site.
Now proceed as follows:
4. Close all applications and turn off energy saving and screensaver.
5. Unplug all peripherals except your keyboard and mouse.
6. Install the update/upgrade. Do not under any circumstances interrupt this procedure. Do not do anything else on your computer while it is installing. Be patient.
7. When it ask for a restart to complete the installation, click restart. This can take longer than normal, there are probably thousands of files to overwrite and place in the correct location. Do nothing while this is going on.
8. Once your Mac is awake, repair permissions again, and you should be good to go!
If your Mac seems slightly sluggish or ‘different’, perform a second restart. It can’t hurt and is sometimes efficacious! In fact a second restart can be recommended.
9. Open a few of your most used applications and check that all is OK. In this connection please remember that not all manufacturers of third party applications and plug-ins, add-ons, haxies etc, will have had time to do any necessary rewrites to their software to make them compliant with the latest version of your operating system. Give them a week or two while you regularly check their websites for updates.
N.B. Do not attempt to install two different updates at the same time as each may have different routines and requirements. Follow the above recommendations for each update in turn.
Lastly, Apple's own article on the subject of Software Update may also be useful reading:
http://docs.info.apple.com/article.html?artnum=106695
[b]If you are updating Safari (or just have):[/b]
Input Managers from third parties can do as much harm as good. They use a security loophole to reach right into your applications' code and change that code as the application starts up. If you have installed an OS update and Safari is crashing, the very [i]first[/i] thing to do is clear out your InputManagers folders (both in your own Library and in the top-level /Library), log out and log back in, and try again.
So, disable all third party add-ons before updating Safari, as they may not have been updated yet for the new version. Add them back one by one. If something goes awry, remove it again and check on the software manufacturer's website for news of an update to match your version of Safari.
Most errors reported here after an update are due to an unrepaired or undetected inherent fault in the system, and/or a third party add-on.
Additional tips on software installation here:
http://docs.info.apple.com/article.html?artnum=106692
To reiterate, Input Managers reach right into an application and alter its code. This puts the behavior of the affected application outside the control and responsibility of its developers: a recipe for problems. That's not to say that issues absolutely will ensue as a result of Input Managers, but you, as a user, must decide. If the functionality of a specific Input Manager or set thereof is really important to you, you may well choose to assume the associated risk.
Again, the advice is to remove all Input Managers from the following directories:
/Library/InputManagers
~/Library/InputManagers
especially prior to system updates (they can always be added back one-by-one later).
Solutions for troubleshooting installation, startup, and login issues in Mac OS X v10.5
http://support.apple.com/kb/TS1541?viewlocale=en_US

I have mac os x10.4.11 Tiger , i tried to update and after I did that when I tried to use itunes, but it doesn't open.. can anyone tell me what I have to do to fix this ??

I have mac os x10.4.11 Tiger , i tried to update and after I did that when I tried to use itunes, but it doesn't open.. can anyone tell me what I have to do to fix this ??

Hello,
Leopard requirements/10.5.x...
    * Mac computer with an Intel, PowerPC G5, or PowerPC G4 (867MHz or faster) processor
minimum system requirements
    * 512MB of memory (I say 1.5GB for PPC at least, 2-3GB minimum for IntelMacs)
    * DVD drive for installation
    * 9GB of available disk space (I say 30GB at least)
Classic/OS9 Apps no longer supported.
Trouble is Apple no longer sells it, check eBay & such for the Retail version, not the Gray Discs...
http://www.ebay.com/sch/i.html?_nkw=mac+os+x+leopard+retail+10.5
There are workarounds if the 867MHz CPU is the only hangup...
http://sourceforge.net/projects/leopardassist/
http://lowendmac.com/osx/leopard/unsupported.html
So we know more about it...
At the Apple Icon at top left>About this Mac, report the version of OSX from that window, then click on More Info, then click on Hardware> and report this upto but not including the Serial#...
Hardware Overview:
Model Name: eMac
Model Identifier: PowerMac6,4
Processor Name: PowerPC G4 (1.2)
Processor Speed: 1.42 GHz
Number Of CPUs: 1
L2 Cache (per CPU): 512 KB
Memory: 2 GB
Bus Speed: 167 MHz
Boot ROM Version: 4.9.2f1

HT3421 I get this error This update requires Mac OS X Tiger 10.4.11 or newer or Mac OS X Leopard version 10.5.6 or newer.

I need to download this: (http://support.apple.com/kb/DL788) because my macbook wont turn on unless its charged. I did all the resets like VPRAM, SMC, and I forgot the other one.
My pack thingy is 0002 and it says that if its 0003 then you dont need the update but I do need the update.
I get this error:
This update requires Mac OS X Tiger 10.4.11 or newer or Mac OS X Leopard version 10.5.6 or newer.
I purchased the battery in December. It worked fine but now its happening again! Please help! Its annoying and the nearest Apple store is 2 hours away!

Please help me!

Problem Update Flash CS3 (9) to Flash C3 (9.02)- MAC OS X Tiger

Hi everybody,
I am on MAC OS X Tiger. My flash is version 9.0 (CS3) and the
software is install in the default configuration
(/Applications/Adobe Flash CS3/...).
My problem is the update for Flash CS3 to get the 9.02
version works wrongly.
I doubleclick on it. I write my request password to install
software or update (It's own to MAC).
And then the Installer tells me that there is an Error
because it didn't find the location of my software.
Is there any thing that I can do to help the updater to find
the good place ? Is there manual installer ? Which file is corrupt
I can remove and install again the software because I am
temporary in Singapore and my DVD is in France.
I am open to any suggestion.
Xeonarno

By abnormally shutting down the OS X partition has most likely gotten scrambled. You will have to reformat that volume and reinstall OS X.
Since OS 9 is working you may still be able to copy your personal files to an external drive so they won't be lost.

I-Mac G-4 very slow running after update from Panther to Tiger 10.4.

I-Mac G-4 800 MHz, 768 Ram; updated to Tiger 10.4 from Panther; used DiskWarrior to recreate new catalog; used System Optimizer X to optimize. Neither helped. Start up takes approximately 4+ minutes! Was faster before. Use computer for IL 10.0 and PS 7.0 graphics design. Not internet connected at this time. Ideas? Help?
Rickety
I-Mac Mac OS X (10.4) 800 MHz; 768 SDRAM

Hi Rickety
My best guess is that you have some application which runs a daemon in the background, and which is not compatible with Tiger. Possible suspects are Virex, Norton AV 9, Norton Utilities, ermm, Cisco VPN.
Check your third party applications for Tiger compatibility. Please report back: I've had a lot of people not reply lately, and so I do not know whether my suggestions have helped, or whether there is further help needed with the problem.
Matthew Whiting

Downloading issue after updating Mac OS X Tiger 10.4.9

I got an information about there're new versions for iturns, safari, Quick Time, Mac OS X, so I clicked the "update" for all. But after updating, I found the speed of downloading softwares from internet become so slow-more than 30 times slower! I don't know whether this problem is because of the system updating from my original 10.4.9, or other reasons?

That's a lot of updates to digest all at once.
There are no guarantees, but following this procedure when installing updates and upgrades on your Mac will go a long way towards avoiding unpleasant after effects and ‘post-update stress disorder’.
It is also worth noting that it is an extreme rarity for updates to cause upsets to your system, but they may well reveal pre-existing ones, particularly those of which you may have been unaware. If you are actually aware of any glitches, make sure they are fixed before proceeding further.
So before you do anything else:
If you can, make a full backup first.
Turn off sleep mode for both screen and hard disk.
1. Repair Permissions (in Disk Utility)
2. Verify the state of your hard disk using Disk Utility. If any faults are reported, restart from your install disk (holding down the C key), go to Disk Utility, and repair your startup disk. Restart again to get back to your startup disk.
At least you can now be reasonably certain that your system does not contain any obvious faults that might cause an update/upgrade to fail.
3. Download the correct version of the COMBO update from the Apple download site. If your car runs on gasoline you would not want to fill the tank with diesel, so don’t try to install the PPC updater on an Intel Mac!
If you prefer to download updates via Software Update in the Apple menu (which would ensure that the correct version for your Mac was being downloaded), it is not recommended to allow SU to install major (or even minor) updates automatically. Set Software Update to just download the updater without immediately installing it. There is always the possibility that the combined download and install (which can be a lengthy process) might be interrupted by a power outage or your cat walking across the keyboard, and an interrupted install will almost certainly cause havoc. Once it is downloaded, you can install at a time that suits you. You should make a backup copy of the updater on a CD in case you ever need a reinstall.
Using the Combo updater ensures that all system files changed since the original 10.4.0 are included, and any that may have been missed out or subsequently damaged will be repaired. The Delta updater, although a temptingly smaller download, only takes you from the previous version to the new one, i.e. for example from 10.4.9 to 10.4.10. Software Update will generally download the Delta updater only. The preferable Combo updater needs to be downloaded from Apple's download site.
Now proceed as follows:
4. Close all applications.
5. Unplug all peripherals except your keyboard and mouse.
6. Install the update/upgrade. Do not under any circumstances interrupt this procedure. Do not do anything else on your computer while it is installing. Be patient.
7. When it ask for a restart to complete the installation, click restart. This can take longer than normal, there are probably thousands of files to overwrite and place in the correct location. Do nothing while this is going on.
8. Once your Mac is awake, repair permissions again, and you should be good to go!
If your Mac seems slightly sluggish or ‘different’, perform a second restart. It can’t hurt and is sometimes efficacious!
9. Open a few of your most used applications and check that all is OK. In this connection please remember that not all manufacturers of third party applications and plug-ins, add-ons, haxies etc, will have had time to do any necessary rewrites to their software to make them 10.4.10. compliant. Give them a weeks or two while you regularly check their websites for updates. This applies particularly to plug-ins for Safari 3.
N.B. Do not attempt to install two different updates at the same time as each may have different routines and requirements. Follow the above recommendations for each update in turn.

Mac OS 10.4. 11 Combo update (PPC) bug?

Installed the update above after software update check. On restart the Imac stops witth a black screen and the fan going at full speed. The "on" light is lit.
I have done the following actions:
1. started from the installer that came with the computer (Mac s 10.3)
repaired permissions. repaired disk.
2. Installed system 10.3 again.Works fine.
trashed many files to make 18 GB free space on the hard disk.
3. Upgraded to Tiger 10.4. Works fine.
4. repaired permissons again.
5 . Did another Software update download and install of the Combo update.
6. Result: black screen, fan going at full, "on " light on.
Any good advice ?

Good advice?
There are no guarantees, but following this procedure when installing updates and upgrades on your Mac, or even re-installing them, will go a long way towards avoiding unpleasant after effects and ‘post-update stress disorder’.
It is also worth noting that it is an extreme rarity for updates to cause upsets to your system, as they have all been extensively beta-tested, but they may well reveal pre-existing ones, particularly those of which you may have been unaware. If you are actually aware of any glitches, make sure they are fixed before proceeding further.
So before you do anything else:
If you can, make a full backup first.
Turn off sleep mode for both screen and hard disk.
Disconnect all peripherals except your keyboard and mouse.
1. Repair Permissions (in Disk Utility)
2. Verify the state of your hard disk using Disk Utility. If any faults are reported, restart from your install disk (holding down the C key), go to Disk Utility, and repair your startup disk. Restart again to get back to your startup disk.
At least you can now be reasonably certain that your system does not contain any obvious faults that might cause an update/upgrade to fail.
3. Download the correct version of the COMBO update from the Apple download site. If your car runs on gasoline you would not want to fill the tank with diesel, so don’t try to install the PPC updater on an Intel Mac!
The 10.4.11 Combo Updater for PPC Macs is here: http://www.apple.com/downloads/macosx/apple/macosx_updates/macosx10411comboupdat eppc.html
And for Intel Macs: http://www.apple.com/downloads/macosx/apple/macosx_updates/macosx10411comboupdat eintel.html
If you prefer to download updates via Software Update in the Apple menu (which would ensure that the correct version for your Mac was being downloaded), it is not recommended to allow SU to install major (or even minor) updates automatically. Set Software Update to just download the updater without immediately installing it. There is always the possibility that the combined download and install (which can be a lengthy process) might be interrupted by a power outage or your cat walking across the keyboard, and an interrupted install will almost certainly cause havoc. Once it is downloaded, you can install at a time that suits you. You should make a backup copy of the updater on a CD in case you ever need a reinstall.
More information on using Software Updater here:
http://support.apple.com/kb/HT1338
Using the Combo updater ensures that all system files changed since the original 10.4.0 are included, and any that may have been missed out or subsequently damaged will be repaired. The Delta updater, although a temptingly smaller download, only takes you from the previous version to the new one, i.e. for example from 10.4.10 to 10.4.11. Software Update will generally download the Delta updater only. The preferable Combo updater needs to be downloaded from Apple's download site.
Now proceed as follows:
4. Close all applications.
5. Unplug all peripherals except your keyboard and mouse.
6. Install the update/upgrade. Do not under any circumstances interrupt this procedure. Do not do anything else on your computer while it is installing. Be patient.
7. When it ask for a restart to complete the installation, click restart. This can take longer than normal, there are probably thousands of files to overwrite and place in the correct location. Do nothing while this is going on.
8. Once your Mac is awake, repair permissions again, and you should be good to go!
If your Mac seems slightly sluggish or ‘different’, perform a second restart. It can’t hurt and is sometimes efficacious!
9. Open a few of your most used applications and check that all is OK. In this connection please remember that not all manufacturers of third party applications and plug-ins, add-ons, haxies etc, will have had time to do any necessary rewrites to their software to make them 10.4.10. compliant. Give them a weeks or two while you regularly check their websites for updates. This applies particularly to plug-ins for Safari 3.
N.B. Do not attempt to install two different updates at the same time as each may have different routines and requirements. Follow the above recommendations for each update in turn.
Lastly, Apple's own article on the subject of Software Update may also be useful reading:
http://docs.info.apple.com/article.html?artnum=106695
If you are updating Safari (or just have):
Input Managers from third parties can do as much harm as good. They use a security loophole to reach right into your applications' code and change that code as the application starts up. If you have installed an OS update and Safari is crashing, the very first thing to do is clear out your InputManagers folders (both in your own Library and in the top-level /Library), log out and log back in, and try again.
So, disable all third party add-ons before updating Safari, as they may not have been updated yet for the new version. Add them back one by one. If something goes awry, remove it again and check on the software manufacturer's website for news of an update to match your version of Safari. Remember: Tiger up to 10.4.10 used Safari 2.0.4 or, if you downloaded it, Safari 3.0.3 beta. Safari 10.4.11 used Safari 3.0.4 which was not a beta. If Safari 3.1.2 on 10.4.11 is not the fastest browser you have ever used, then something is wrong!
Moreover, trying to revert to Safari 3.0.4 (or worse still, version 2) when running 10.4.11 or 10.5 can have repercussions, as Safari 3.1.1 uses a completely different webkit on which other applications like iChat, Mail and Dashboard Widgets etc also rely, and may entail you having to reinstall an earlier operating system.
Most errors reported here after an update are due to an unrepaired or undetected inherent fault in the system, and/or a third party ad-on. Two such add-on that have been frequently mentioned here for causing such problems are Piclens and Pithhelmet. If you have them, trash them.
Additional tips on software installation here:
http://docs.info.apple.com/article.html?artnum=106692
To reiterate, Input Managers reach right into an application and alter its code. This puts the behavior of the affected application outside the control and responsibility of its developers: a recipe for problems. That's not to say that issues absolutely will ensue as a result of Input Managers, but you, as a user, must decide. If the functionality of a specific Input Manager or set thereof is really important to you, you may well choose to assume the associated risk.
Again, the advice is to remove all Input Managers from the following directories:
• /Library/InputManagers
• ~/Library/InputManagers
especially prior to system updates (they can always be added back one-by-one later).

TROUBLE with Mac OS X Tiger install on G4 iMac 1.25 GHz

Trying to install retail copy of Mac OS X Tiger 10.4 onto an iMac G4 1.25 GHz running OS X 10.3.9. The DVD shows up on the desktop when inserted, but after clicking install and waiting for the reboot, the system just loads OS X 10.3.9 and NOT the 10.4 setup.
Inserting the CD and holding "C" during startup yields the blinking system folder with the question mark.
Apparently no firmware updates are needed and the iMac meets the requirements. Any ideas, suggestions, or workarounds are much appreciated.
I also have a MacBook Pro (Intel, of course), and was wondering if there was any way to use it to install the PPC version of 10.4 on the iMac. (Can I boot the iMac as target disk mode on my MBP and install the PPC version of Tiger onto it that way? I don't know if that will work with the intel/ppc hiccup.)
Someone please tell me how to get this working!

Yes, unless you have the original install disks that came with the computer ( with iLife included) you will have to buy iLife. However, iLife 11 requires an intel processor and snow leopard. If you don't meet those requirements you should try to find an older version. ( usually you can find something on amazon.com)
David

Mac os 10.4.10 software update problem -- my mac does not work anymore :(

hello!
i have a powerbook G4- PPC. just today, i did a software update of my OS to 10.4.10 (it was the available update version according to the automatic uptae) and during the final stage of the installation, it says "a problem was encountered...installation package is moved to trash"
when i browsed my mac, my apps does not work anymore!!! they just bounce from the dock when i clicked it but it won't open any window. i emptied the trash and restarted my mac but sadly, it just boot but won't continue to the log in part, only in the silver window with the apple logo and mac os x tiger... and the mouse just turns into the color wheel. i waited for 30 mins and nothing happened.
i don't have a startup disc because the mac is a gift and it was long time ago. is ther a software i can use to fix or revert the changes of the unsuccessful OS update? why is there always a problem when i do OS update? isn't apple software stable?
My mac problems' driving me crazy!!!

There are no guarantees, but following this procedure when installing updates and upgrades on your Mac will go a long way towards avoiding unpleasant after effects and ‘post-update stress disorder’.
It is also worth noting that it is an extreme rarity for updates to cause upsets to your system, but they may well reveal pre-existing ones, particularly those of which you may have been unaware. If you are actually aware of any glitches, make sure they are fixed before proceeding further.
So before you do anything else:
If you can, make a full backup first.
Turn off sleep mode for both screen and hard disk.
1. Repair Permissions (in Disk Utility)
2. Verify the state of your hard disk using Disk Utility. If any faults are reported, restart from your install disk (holding down the C key), go to Disk Utility, and repair your startup disk. Restart again to get back to your startup disk.
At least you can now be reasonably certain that your system does not contain any obvious faults that might cause an update/upgrade to fail.
3. Download the correct version of the COMBO update from the Apple download site. If your car runs on gasoline you would not want to fill the tank with diesel, so don’t try to install the PPC updater on an Intel Mac!
If you prefer to download updates via Software Update in the Apple menu (which would ensure that the correct version for your Mac was being downloaded), it is not recommended to allow SU to install major (or even minor) updates automatically. Set Software Update to just download the updater without immediately installing it. There is always the possibility that the combined download and install (which can be a lengthy process) might be interrupted by a power outage or your cat walking across the keyboard, and an interrupted install will almost certainly cause havoc. Once it is downloaded, you can install at a time that suits you. You should make a backup copy of the updater on a CD in case you ever need a reinstall.
Using the Combo updater ensures that all system files changed since the original 10.4.0 are included, and any that may have been missed out or subsequently damaged will be repaired. The Delta updater, although a temptingly smaller download, only takes you from the previous version to the new one, i.e. for example from 10.4.9 to 10.4.10. Software Update will generally download the Delta updater only. The preferable Combo updater needs to be downloaded from Apple's download site.
Now proceed as follows:
4. Close all applications.
5. Unplug all peripherals except your keyboard and mouse.
6. Install the update/upgrade. Do not under any circumstances interrupt this procedure. Do not do anything else on your computer while it is installing. Be patient.
7. When it ask for a restart to complete the installation, click restart. This can take longer than normal, there are probably thousands of files to overwrite and place in the correct location. Do nothing while this is going on.
8. Once your Mac is awake, repair permissions again, and you should be good to go!
If your Mac seems slightly sluggish or ‘different’, perform a second restart. It can’t hurt and is sometimes efficacious!
9. Open a few of your most used applications and check that all is OK. In this connection please remember that not all manufacturers of third party applications and plug-ins, add-ons, haxies etc, will have had time to do any necessary rewrites to their software to make them 10.4.10. compliant. Give them a weeks or two while you regularly check their websites for updates. This applies particularly to plug-ins for Safari 3.
N.B. Do not attempt to install two different updates at the same time as each may have different routines and requirements. Follow the above recommendations for each update in turn.
Lastly, Apple's own article on the subject of Software Update may also be useful reading:
http://docs.info.apple.com/article.html?artnum=106695

Updating problem to tiger 10.4.8

I purchased the tiger upgrade 10.4.6 yesterday after being a panther user. After installing the 10.4.6 upgrade successfully I went on to the apple site to update tiger by downloading the 10.4.8 version. But when I try to install the new update, I can not do it, the system won't let me choose a the hard drive to install the update. any suggestions

Welcome to Apple Discussions!
Are you sure you downloaded the PowerPC (also known as PPC) update? Macs which could run 10.4.4 updates and earlier versions of Mac OS X are only PowerPC.
Are you following the tips I've made* for upgrading?
http://www.macmaps.com/upgradefaq.html
P.S. Please try to only click once the Post Message/Save button when posting. If it doesn't appear that the post has been posted, go to the forum link and refresh your web browser to see if your post has been added. I see you posted two extra posts by accident.
* Links to my pages may give me compensation.

Mac G3 w/ Tiger 10.4.3 update problem/issue "digital signature incorrect"

Similar Messages

Maybe you are looking for