Mac Mini '09 incompatible with older flat panel TV's?

I just bought a Mac Mini '09 and tried to hook it up to an old (2002) Sony Plasma 32" TV. I am using the mini-DVI to S-video/composite video adapter. I get a "no signal" response from the TV, indicating that the Mini and the TV are not communicating. My black '06 MacBook is able to successfully connect to the Sony TV using the exact same adapter and cable combination. The TV only has component video, s-video, and composite video inputs -- no digital inputs.
I spoke with an Apple Care person, and she and I agreed that there is likely a compatibility issue with the new Mac Mini's video card and older TV's. I have also seen it suggested that the new Mini's DVI port will not pass on an analog video signal. Is there any fix for this, either a driver or a cable adapter? Would one of the display manager programs (SwitchResX, etc.) be helpful? Do I need to get a new TV?

It sounds like the new Mac Mini has HDCP enabled (as it is on the new MacBooks and MacBook Pros).
This is a kind of copy protection, and will not allow HDCP protected content to be played on an analog source.
A tool like http://www.hdfury.com/ will take the HDCP stream, and convert it to an analog stream. It's perfectly legal.. and will extend the life of older TV's (manufactured before 2002).

Similar Messages

Cant get Apple TV to work properly with older flat panel TV.

I have an older flat panel, a 42" philips 42pf9630a. This one:
http://www.retrevo.com/support/Phili.../278bh337/t/2/
I plugged my brand new Apple TV into the HDMI and switched input on the TV. I can see the Apple TV main menu but it blips in and out, toggling between the main menu and snow. Obviously there's some sort of communication issue between the Apple TV and my Philips. I have successfully used this apple TV on several other TV's in the past couple of months.
Is it because my TV is too old? Any suggestions on what I can do to fix this??
Thanks for your help!

Go in to the network and sharing center (in control panel), with the pc connected by wire. Right inder the little "map" of her network, it will list the available networks (probably only one listed), click customize and set it to private, you can also name it if you want so its more easily identified.
Also, make sure file sharing and network discovery are "on".
Message Edited by Frunple on 03-17-200705:50 AM

New mac mini, resolution incompatible with TV

My shiny new mac mini just arrived today in the mail. I hooked it up to my Emerson 27 inch 720p tv and booted her up. I got the grey screen, then the apple, then a spinny wheel of white lights, then "Please change computers resolution".
This is my first boot and the machine only comes with the onboard HDMI port and the HDMI to DVI adapter. I have no DVI monitors, and my only HDMI monitor is my TV.
Safe boot doesn't work, single user mode doesn't work. Both just throw the same error, safe boot runs a progress bar for a bit before doing so at least.
Apple support is closed right now (***).
My bro and I are Linux admins so we got into the shell and tried editing the com.boot file to change the resolution, but that didn't seem to do anything.
All the forums I've referenced say to install tools to solve this problem, but that's not helpful unless I can get in the first time. Also unhelpful are the people who say buy a new TV or monitor, which cost more then the machine.
I need this machine to boot exactly once into the GUI so I can set up logmein, VNC, and ssh. This is a dev box so I don't care about seeing it on the TV.
Can anyone get me into the GUI one time?
Since it's brand new, it's running Lion which I've been having endless issues with at work.

It sounds like the new Mac Mini has HDCP enabled (as it is on the new MacBooks and MacBook Pros).
This is a kind of copy protection, and will not allow HDCP protected content to be played on an analog source.
A tool like http://www.hdfury.com/ will take the HDCP stream, and convert it to an analog stream. It's perfectly legal.. and will extend the life of older TV's (manufactured before 2002).

Mini display incompatible with older ADC-displays?

I have no problem connecting my 23" aluminum bezel display in my office to my new 13" MBP, but when I wanted to hook up my older model 20" Cinema Display (plastic grey bezel) at home, the display was not recognized. Does anybody know if this is indeed the case?
Thanks,
Jan

For no reason, the display started working. Perhaps the connection was not fully established before. But it works and has been working for a few days now.

HT2998 Hi, I try to conect Mac Mini from 2009 with my HD Tv Samsung F 6400 . With Mini Dvi conection and adapter to HDMI input in TV I got picture but not sound! I have analog cable from the phones out from mac but imposible to conect to TV? Can you HLP

Hi, I try to conect Mac Mini from 2009 with my HD Tv Samsung F 6400 . With Mini Dvi conection and adapter to HDMI input in TV I got picture but not sound! I have analog cable from the phones out from mac but imposible to conect to TV? Can you HLP?

You really need a newer Mac Mini with a true HDMI output, because that Mac Mini's DVI output does not support Audio.
You might try a 3.5mm to RCA adapter
from the Mac Mini's headphone jack to the TV's audio input,
but that would require being able to select the Audio input in the TVs menu while using it's HDMI input.
Optionally you could also use an external 2.1 Speaker System or patch the audio from the Mac Mini to your home stereo system to enhance that older Mac Mini's audio.

How do i reformat my hard drive on mac mini late 2011 with yosemite before selling my mac

how do i reformat my hard drive on mac mini late 2011 with yosemite before selling my mac

You can't legally sell or give away that computer with Yosemite installed.
Before you sell or give away your computer, in addition to the steps listed in this support article, take these steps:
1. Run Apple Diagnostics or the Apple Hardware Test. The buyer will do this (or he should), and you don't want to be surprised by the results.
2. Reset the PRAM and the SMC, which might contain personal information.
3. If you set a firmware password, remove it by running Firmware Password Utility in Recovery mode.
4. If you activated FileVault in OS X 10.7 or later, turn it off.
5. If you use Boot Camp, the partition must be deleted.
6. If you created any other data partitions on the internal drive, remove them in Disk Utility.
7. If the machine has an internal hard drive, erase the one remaining data partition with the option to zero out data. An SSD doesn't need to be zeroed.
You can't legally or practically transfer any software downloaded from the Mac App Store to the new owner of the machine, even if it was free. That includes OS X, so if you upgraded to OS X 10.7 or later, you must reinstall an older OS, either from the installation media, if applicable, or by starting up in Internet Recovery mode (option-command-R at the startup chime.) If you installed from physical media, deliver those to the new owner.
If you're selling the machine, or donating it in working order, and it originally shipped with OS X 10.4 or 10.5, then you have the option of installing either from the discs that came with it or from a retail Snow Leopard disc (which you must then transfer to the buyer.) The buyer should understand that if he doesn't get the original discs from you, he won't get the bundled iLife applications or the Apple Hardware Test. Replacements for the original discs can be ordered from Apple.
The new owner will have to redownload any software that came from the App Store, including OS X upgrades, under his or her Apple ID. If you ever updated the bundled iLife applications (Garage Band, iMovie, and iPhoto) through the App Store, you can't transfer those either. The buyer will have to purchase them.
Remove the machine from your list of registered products. If it's still covered by an AppleCare Protection Plan, transfer the coverage to the new owner by following the instructions in the AppleCare Terms and Conditions (under the heading "Transfer of Plan.")

Mac Mini Server 2011, with lion, sleeps every day

My new Mac Mini Server 2011, with lion, sleeps every day! Server not responding.
All services are down, smb, vnc, ssh too. And it not should be happen because this is a server, right?
Please, I need help with this problem!
How to fix it?

1. Go to System Preferences.
2. Select Engery Saver
3. Slide the setting for Computer sleep to never.
4. Slide the setting for Display sleep to never (though I believe the display should be able to sleep without much issue.
5. Make sure the following are not selected:
a. Put the hard disk(s) to sleep when possible.
b. Allow power button to put the computer to sleep.
6. Make sure the following are selected:
a. Wake for network access
b. Start up automatically after a power failure
c. Restart automatically if the computer freezes.
Good luck!

Can. I use my MAC Mini in conjunction with my iMac?

Can I use my MAC Mini in conjunction with my iMAC? I can not upgrade the OS of the iMAC due to software that I need and Lion does not support it.
If I could bounce back an forth or use the software from the MAC Mini with the iMAC, this would solve my dilemma.

Before I buy a networked drive can I use the airport to connect with an external
USB drive and set both macs use the drive as a time machine
Can you hook this up? Sure.
Is is supported by Apple? No.
Some users report that this seems to work when they try it.
Others....like me....have corruption problems anywhere from a few days to a few months after I set up a test....which I do whenever a new version of firmware or a new operating system becomes available.
We cannot predict your results, so if you decide to try this, and your backups are valuable, you might want to have a secondary backup plan in place as well....just in case.

Setting up the Mac Mini (non server) with RAID 1

I have a regular Mac Mini (Mid 2011) with Lion OS. I would like to change the hard disk to 2 1TB drives and use RAID1 to add some reliability to my data. Is this possible in the non-server Mac mini? Do I need to remove all my data to convert the system to RAID1 (assuming I can)?

Yes- Colin Jeukens posted step by step instructions back a couple of months ago. Here it is again...
Out of the box the mini comes without Raid. You have two identical HDs of 500Gb.
I have just set it up as Raid1. You can't do this when you use the startup disk from the mini. And as you don't have a Superdrive ... you need to be creative. You need another Mac with Firewire.
Step 1: Start the Mini in Target Mode. Press the T during start. In a few seconds the firewire logo will appear on your screen.
Step 2: Go to your second Mac. Connect the firewire cable between second Mac and Mini.
Step 3: On the second Mac start the disc utility. The two identical drives on your mini will show. Create a new Raid set (mirrored = Raid 1). Include both drives. Confirm the warning that all data on the mini will be lost.
Step 4: Make sure your second Mac has CD/ DVD sharing option installed. This is tou use the superdrive to install OS X Server on the mini.
Step 5: Shutdown both Macs
Step 6: Start your second Mac in target mode. Make sure the firewire cable is still connected.
Step 7: Start the Mini with the option key pressed.
Step 8: Insert the OS X Server install disc in your second Mac.
Step 9: wait till the drive logo apears om the Mini. Continue the install. Will take about an hour.
Here is a link to the original post...
http://discussions.apple.com/thread.jspa?threadID=2213470&tstart=0

Will the mac mini definitely work with a 50 hertz tv?

Just wondering if the mac mini will work with a 50 hertz tv

Yep - just go to the System Preferences and choose display and hit 'detect display' which will give you 1080x and other TV resolution options (assuming you have a modern LCD or similar).
You should then be able to select 50 or 60 hz.

Mac mini having issues with system preferences retaining settings

Mac mini having issues with system preferences retaining settings; this was present with Mavericks and now Yosemite after installation. Did try removing com.apple.systemprefs.plist file (library/preferences folder) to trash, but couldn't find it in trash in order to empty it. Upon reboot the file is still missing. Please don't suggest reloading Yosemite, have very slow internet connection, Yosemite took 7-8 hours to D/L.
Any troubleshooting suggestions out there? thanks

Well, I'd open Font Book, it's included with OSX, & see what it says for Validate & Duplicates.
I would also like to add I am new to Apple computers and I'm doing my best to stay up to par with whats what and understanding!
No problem, we were all new to everything once, do let us know if you need more help or clatification.

My mac mini loses connection with my receiver after turning off the receiver then back on

My Mac Mini loses connection with my Onkyo receiver NR-609 after turning off the receiver then back on. The only way to reistablish the connection is to unplug then replug the HDMI cable to the Mac Mini. There's no effect if I unplug then replug the HDMI to the receiver. Any help or suggestions would be appreciated. I've searched a lot but haven't found much of anything so if this is covered elsewhere I would greatly appreciate a link.
Thanks in advance

Hi and thanks. I don't know about the audio prefs. When it happens I am not able to see or hear anything from the computer until I un/re-plug the HDMI to the Mini. I'm not sure it's changing to something else because there's nothing else connected for it to change to. I could see that perhaps the audio will change to the Mac Mini's internal speaker.
I found out last night that if, after I lose the signal, I use my ipad to play a video on the Mac Mini using the Remote app and home sharing the signal gets righted and I can see/hear the computer again. It's quite an inconvenient fix though and I wish and hope someone here can help me.

Will the new mac mini work with the older Flat panel iMac globe speakers?

I am thinking it might be time to upgrade my 800mhz FP 17", and since i have an extra 22" monitor laying around being unused, i thought the Mac mini would be a drop in replacement...but then i thought about the imac FP speakers and i would like to keep using them...is anyone using these speakers with the mac mini?

The Apple 'Pro speakers' that were designed by Apple and Harman Kardon, use a proprietary 2.5mm mini jack connector and they would need an adapter to work.
Years ago there was a product called the 'iFire' that allowed those speakers to be used with other macs with a firewire port ..... Here's a site that I found that has more information than you'll need to know about the speakers and the adapter: http://maczealots.com/reviews/ifire/
At the time, the pro speakers technology was pretty cool ... combining power and digital audio into the one cable. I still think they look striking....
I did a bit of snooping around and couldn't find the adapter for sale (aside from a used one on Amazon for $199 ouch) .... I believe it has been discontinued.
I think you'll have to follow another route.....

Mac mini slow, especially with Office 2004

I just upgraded from an iMac flat screen to a 1.83 GHz Mac Mini. The move was easy and I'm not experiencing any major bugs, but for a lot of things I'm finding the mini slower than my old iMac. In particular, the two Office 2004 applications I use all the time, Word and Entourage, take a lot longer to open and move around in, with a lot of rotating rainbow time. I installed Office 2004 when I got the mini, but I'd transferred Office X over from the older computer. Would it help to take off Office X? Any ideas?
1.83 GHz Mac Min Mac OS X (10.4.8)

As per the reply to your other post with the same question:
This is not something to worry about or be concerned with. Firstly, the paging counts will depend on how long the system has been running since the last boot, but MacOS is designed to actively page out and in, so in itself, the fact your system shows it is doing so means nothing at all.
If your computer is exhibiting some indication of a problem, I suggest you start a new thread here and describe what you are experiencing. That way we can help you directly with the specifics of your problem. On the other hand, if you have just seen the comments regarding paging and system performance and have checked your own Mac to see what it's doing - the answer is that in the absence of an indication of a problem, it's very likely doing exactly what it ought to be doing!

Installation of leopard from one mac mini to another with dead CD/DVD drive

Is it possible to install Leopard on to an older mac mini that has a nonfunctioning CD-RW/DVD-ROM drive but otherwise works fine for what it is
Hardware Overview: Machine Model: Mac mini
CPU Type: PowerPC G4 (1.1) CPU Speed: 1.25 GHz
L2 Cache (per CPU): 512 KB Memory: 256 MB
Bus Speed: 167 MHz Boot ROM Version: 4.8.9f1
Serial Number:
TOSHIBA MK4025GAS:
Capacity: 37.26 GB
Model: TOSHIBA MK4025GAS
Revision: KA100P
Serial Number:
Removable Media: No
Detachable Drive: No
BSD Name: disk0
HARD DISK:
Capacity: 37.13 GB
Available: 9.02 GB
Writable: Yes
File System: Journaled HFS+
BSD Name: disk0s3
Mount Point: /
MATSHITA CD-RW CW-8123:
Manufacturer: MATSHITA
Model: MATSHITA CD-RW CW-8123
Revision: CAD4
Serial Number:
Drive Type: CD-RW/DVD-ROM
Disc Burning: Apple Supported/Shipped
Removable Media: Yes
Detachable Drive: No
Protocol: ATAPI
Unit Number: 1
Socket Type: Internal
FROM a mac mini that HAS a functioning CD/DVD drive
Model Name: Mac mini
Model Identifier: PowerMac10,1
Processor Name: PowerPC G4 (1.2)
Processor Speed: 1.42 GHz
Number Of CPUs: 1
L2 Cache (per CPU): 512 KB
Memory: 512 MB
Bus Speed: 167 MHz
Boot ROM Version: 4.8.9f4
Serial Number:
MATSHITA CD-RW CW-8124:
Firmware Revision: DACD
Interconnect: ATAPI
Burn Support: Yes (Apple Shipping Drive)
Cache: 2048 KB
Reads DVD: Yes
CD-Write: -R, -RW
Write Strategies: CD-TAO, CD-SAO, CD-Raw
Media: Insert media and refresh to show available burn speeds
I thought maybe I could do it with firewire but no luck...
any help would be greatly appreciated
Message was edited by: Moderator

k...
Boot the mini into TD mode
Connect it to the "other" Mac
Insert the install disk in the "other" Mac
Start the installer which will reboot the "other" Mac
Once the "other" Mac has restarted and is running from the install disk, you should be able to select the Mini's drive (the FW disk) as the install destination. If not, go into the Disk Utility (under the "Utilities" menu) and check out the FW disk. You may need to "repair" it, repair permissions or reformat it depending on the condition of the disk and the type of partition it contains.

Mac Mini '09 incompatible with older flat panel TV's?

Similar Messages

Maybe you are looking for