Mac mini, bluetooth connection problems

Hi, My mac mini (latest model) has recently got problems with the bluetooth connections to the keyboard and the mouse.
It seems to be some kind of interference to the wireless signal that makes the KB/Mouse to lose connection, and then
connect again.
I assume that it was one recent update that caused this as it worked without any problems for months before it
started by itself.
Any tips?

https://discussions.apple.com/message/20738621#20738621
2012 Mini Bluetooth/USB3 Interference: Apple Support Communities
http://blog.macsales.com/15990-shielding-resolves-usb-3-0-conflict-with-bluetoot h

Similar Messages

  • Mac Mini Bluetooth hardware problems ?

    I own a Mac Mini Intel Core 2 Duo 1Gb bought last October, an Apple wireless keyboard and an Apple wireless mouse, both I formerly use without any problems with my old Powerbook G4. By now, I used them with my Mac Mini it worked perfectly fine. But since two or three weeks, I’ve got big Bluetooth connection problem. Randomly, after one or two hours of use, both keyboard and mouse loose connection and the Bluetooth symbol change itself into a strange one. I had a look on your site to learn the meaning of it and the symbol is see which is a Bluetooth symbol with a horizontal zebra means that no Bluetooth hardware can be found! Does my Mac Mini built-in Bluetooth card have problems?
    Since I haven’t got any wired USB keyboard or mouse I have to reboot my Mac Mini quite roughly. Sometimes one reboot is enough to make the Bluetooth of Mac Mini to work again, sometimes not and I have to wait a little bit more (more than ten minutes). I can see it works again as the Bluetooth symbol is the right one again (the one with the dots).
    It is very annoying. And I am a bit sad to have such problems with Apple stuff. Is there something I could do to avoid such a waste of time? Or shall I call Apple Care for fear it should be a hardware problem.
    Of course, I use brand new batteries for both of them.
    Message was edited by: Christophe Canus

    ***
    My mini is doing it as well. Just started doing 2-3 weeks ago. Logitech Denovo or Apple Bluetooth. Doesn't matter which. Loses it in about an hour or so. Al Keyboards and mice were purchased at about the same time as the core 2 duo mini, ~ last October.
    Must power cycle the machine to get it back and it must be paired again. Very annoying. Can't remember if it coincides with an Apple update.
    This mini has had the superdrive replaced twice, once within 6 weeks of purchase. Ever since Leopard, it's been close to the best media head. now this...
    Sigh.
    (What makes it not the best? Frontrow doesn't sort titles correctly [1, 10, 2, 3 - wrong!], doesn't force mount aliases in the movies directory, doesn't put out 1080p without hacking. And I'd so love eyeTV integration with Frontrow. It'd be perfect then.)

  • Mac Mini Bluetooth Connections Issues with Airport Extreme

    Hi,
    The issue I'm having is my apple bluetooth devices will not connect to my mac mini. This problem started a few weeks ago and i have narrowed it down to my Airport Extreme which is right next to my Mac Mini. I have tried adjusting the channels and removing the Wide channel option on the Airport Extreme this has helped I can use my magic pad (not really up to par but it works). When I disconnect my Airport all my bluetooth devices work great. Moving my airport extreme isn't an option without a large amount of work putting in a new cable outlet. I don't know what changed from a few weeks ago as the devices have always been within inches of each other and worked fine.
    I was trying to find a way to disable the 2.4 band on the airport extreme but this for as far as i know can't be done. I'm running out of ideas on what to do next any help would be great.

    Are you sure it's not the monitor? Monitors have been known to do this.
    Try changing the broadcast channel on the AEX using the Airport Utility.

  • Problem with mac mini 2012 connection

    Hello!I have a problem with my mac mini 2012 connection!The hdmi to hdmi connection working great at my mac mini!The thunderbolt(mac mini) to hdmi (display) is not working!But when i have the hdmi to hdmi cable and the thunderbolt to hdmi at the same time (my display have two hdmi output) works fine!!But when i unplug the hdmi to hdmi cable stop working the thunderbolt to hdmi!!Any solution for that??I want only the thunderbolt to hdmi connection!!

    Whew, never heard of this problem yet!?
    Is it possible the TB->HDMI is set to mirror the HDMI->HDMI screen?

  • Mac Mini KVM USB problem prevents boot when using certain USB ports

    Hi,
    Just purchased a brand new Mac Mini 2.4 Quad Core to use as a server.
    This morning we removed from the box & connected it to our NTI Unimux 16-port KVM. The KVM already has 10 Mac Mini's connected (various vintages, no problems).
    We connected the Mini to the KVM using HDMI for video and a USB connector.
    The Mini initially refused to boot past the initial white/gray screen. It never got to the Apple or the cog.
    However, we found that if the USB cable from the KVM is disconnected, the Mac Mini booted immediately.
    Further, the Mini will also boot with an Apple keyboard connected.
    So... you may assume that the KVM cable is bad or that there is some firmware compatability issue between the KVM and this new Mac Mini.
    EXCEPT...
    This Mini has 4 USB ports.
    We found that the Mac Mini can boot with the KVM USB cable connected if the USB cable is connected to USB ports 2 or 4 on the Mac Mini.
    If the KVM USB is connected to ports 1 or 3 on the Mini, the Mini will not boot.
    The Mac Mini will boot with an Apple USB keyboard installed on any port.
    Is there any logical reason for this behavior?
    Thanks,
    b

    Hello,
    Great work & very interesting thanks!
    My guess is mA available & mA required, chect System Teport>Hardware>USB for like this...
    USB Bus:
      Host Controller Location:    Built In USB
      Host Controller Driver:    AppleUSBOHCI
      PCI Device ID:    0x0035
      PCI Revision ID:    0x0043
      PCI Vendor ID:    0x1033
      Bus Number:    0x0b
    Bluetooth USB Host Controller:
      Version:    19.65
      Bus Power (mA):    500
      Speed:    Up to 12 Mb/sec
      Manufacturer:    Apple, Inc.
      Product ID:    0x8207
      Vendor ID:    0x05ac  (Apple Computer, Inc.)
    General Purpose USB Hub:
      Version:    1.00
      Bus Power (mA):    500
      Speed:    Up to 12 Mb/sec
      Product ID:    0x2077
      Vendor ID:    0x0451
    802.11 n WLAN:
      Version:    1.01
      Bus Power (mA):    500
      Speed:    Up to 12 Mb/sec
      Manufacturer:    Ralink
      Product ID:    0x5372
      Serial Number:    1.0
      Vendor ID:    0x148f
    MegeCam:
      Version:    1.00
      Bus Power (mA):    500
      Speed:    Up to 12 Mb/sec
      Manufacturer:    MGI
      Product ID:    0x8007
      Vendor ID:    0x060b

  • 2014 mac mini dual monitor problem

    I just brought a mac mini (Late 2014) i have two displays monitors connected, one HDMI to DVI. and one thunderbolt to DVI. I can have both thunderbolts connected and the problem its the same, when back from sleep ,one monitor doesn't turn on. i have to disconnect one and then both work, it only happens when the mac goes to sleep. on cold restart or turning the mac on, this problem doesn't occur. any help.

    I have this same problem too. I purchased the Mac Mini with the intention of running dual monitors. I'm using the HDMI and mini-display/Thunderbolt to DVI. I've also tried MiniDisplay/Thunderbolt to HDMI and I'm experiencing the same problem as angelfromfullerton. Whenever it tries to wake from sleep, it can't decide on monitor arrangement and keeps flicking between the two, making the OS unusable and forcing a reboot... EVERY TIME. I've also experienced the issue once or twice on a cold boot. It doesn't matter which Thunderbolt port is used either.
    I'm going to have to return my Mac Mini unless this problem is fixed asap.
    Mac Min, OSX Yosemite (10.10).

  • Mac-Mini wont connect to wired ethernet

    I can not get my Mac-Mini to connect to the internet via a wired ethernet cable. When I try to connect it says it is getting an IP address and then boots out and tries again. Its a never ending cycle. It does this in both OS X, and Windows. Do I have a bum network card?

    Hi Steve,
    Some ISPs can be fussy about the number of devices you connect to the internet.
    If the Modem routes then it tends to be this network card that is in effect "registered" with the ISP.
    If you have a cable modem then a Router then the router tends to be the device "registered".
    If no router then that is obviously you computer's MAC address.
    Some ISPs will go as far as requesting to actually type in the MAC card address and formally request to change it.
    It sounds like you have here a system of monitoring that is not that "up front" and causes problems enough for people to have several computers and just swap them.
    I would guess it allows one change, like you would need if you have a new computer.
    12:44 PM Wednesday; June 27, 2007

  • Mac Mini with Major Problems

    I'll try to make this short, but it is a looonngg problem.
    About one month ago my Mac Mini began having problems when I boot up.  The computer would freeze on the opening page where I put in my password.  My wireless keyboard and trackpad would not work.  This would be interminent at first but progressively got worse.
    I spent hours on phone tech support.  Finally realizing that would not help I drove the 100 mile round trip to the local Apple store for a Genius bar appointment.
    The first appointment (there have been 5 - meaning 500 miles) resulted in them doing a clean install of Lion.  I took the computer back to the office and guess what, the same problem.
    I drove back to the Apple store, the Genius did some more work and proclaimed it fixed.  It was, for about 3 days when everything started again.
    More time now on tech support.  One more trip to the Apple store.
    This time they kept the Mac Mini for about 4 days are replaced the logic/mother board. 
    I got it back to the office on Thursday. Everthing works great.
    Until today.  I boot the computer, it gets to the screen that has the apple on it - then nothing.
    I manually power it down and reboot.  Same thing.
    I've set up ANOTHER appointment at the Genius bar tomorrow. 
    My question: can I demand that they replace this machine.  Between work and home I have 2 Mac Mini's, a Macbook Pro, a Macbook Air and 2 iPhones.  I've never had this type of problem.  I'm really tired of this.
    I purchased this in February so it is in warranty. 
    Thanks

    rwgleaves wrote:
    I took it to the Apple store Genius bar today - my 5th trip - and they did just what I'd hoped.  They replaced the Mac Mini with a brand new machine. 
    This is why I buy Mac/Apple!
    Excellent new, sorry you had so much trouble on the way. And yes, Apple Stores are awesome!

  • I intend to purchase a Mac Mini and connect to a regular (not smart) flat screen TV and use such as monitor. Can this setup also allow access to Netflix or Apple movies or an Apple TV is also required?

    I intend to purchase a Mac Mini and connect to a regular (not Smart) flat screen TV that will be as such a large monitor. With this setup do I require an additional Apple TV to watch programs from Netflix, Apple Store movies, Y-tube etc?

    You can view NetFlix and YouTube via their websites on a Mac computer. You can purchase/play iTunes movies and other thing via iTunes on the Mac.

  • Having bluetooth connection problem after using Yosemite for a week

    After installing and using Yosemite for a week, I experienced bluetooth connection problems with my magic mouse and headphone, my model is macbook pro retina early 2013, hope to fix this soon

    Hello there Oranger84,
    If I understand correctly you are having some sort of Bluetooth issue between your computer and Magic Mouse and Headphones after installing Yosemite. Depending on the particular symptoms you are seeing, I would recommend the following article to help you get that resolved:
    Troubleshooting wireless mouse and keyboard issues
    Thank you for using Apple Support Communities.
    All the best,
    Sterling

  • Can mac mini work connected to imac desktop

    can mac mini work connected to imac desktop. I know its silly question but can i make the mac mini main operating system on my imac after transferring all of my itunes etc?

    What is Target Display mode?
    But only 27" iMac (Late 2009 or Mid 2010) can do this.
    Since you mentioned an Early 2009 iMac I assume that it is a 24" iMac which sadly has not this capability.
    If I am correct, you might wanna have a look at ScreenRecycler http://www.screenrecycler.com/ScreenRecycler.html
    Stefan

  • 9780 and Playbook bluetooth connection problem

    I have never experienced bluetooth connecting problems between my 9780 and Playbook 64 previously ... but for last few days I cannot connect them. I have deleted both devices and re-paired successfully. I have turned both fully off (removed 9780 battery) and still no connection.
    I have tested both devices by successfully connecting each of them to other bluetooth devices. They just will not connect to each other for some reason.
    The only change was the recent Playbook Software update.
    I use the Bridge and Tethering all the time and so need Bluetooth to be working ... thanks for any assistance.
    Solved!
    Go to Solution.

    maybe you can uninstall then reinstall the Bridge app on your 9780.
    The search box on top-right of this page is your true friend, and the public Knowledge Base too:

  • HT1338 Mac mini display connection will not come back after sleep, I have to shut down and restart the monitor.

    Mac mini display connection will not come back after sleep, I have to shut down and restart the monitor.

    Finder icon on dock, macintosh hd, library, launch agent - delete all files & restart sleep to test
    also
    Finder icon on dock, macintosh hd,
    Library/Preferences/SystemConfiguration/com.apple.PowerManagement.plist
    delete file & restart sleep to test.

  • My mac mini loses connection with my receiver after turning off the receiver then back on

    My Mac Mini loses connection with my Onkyo receiver NR-609 after turning off the receiver then back on.  The only way to reistablish the connection is to unplug then replug the HDMI cable to the Mac Mini.  There's no effect if I unplug then replug the HDMI to the receiver.  Any help or suggestions would be appreciated.  I've searched a lot but haven't found much of anything so if this is covered elsewhere I would greatly appreciate a link.
    Thanks in advance

    Hi and thanks.  I don't know about the audio prefs.  When it happens I am not able to see or hear anything from the computer until I un/re-plug the HDMI to the Mini.  I'm not sure it's changing to something else because there's nothing else connected for it to change to.  I could see that perhaps the audio will change to the Mac Mini's internal speaker. 
    I found out last night that if, after I lose the signal,  I use my ipad to play a video on the Mac Mini using the Remote app and home sharing the signal gets righted and I can see/hear the computer again.  It's quite an inconvenient fix though and I wish and hope someone here can help me.

  • Mac mini bluetooth and safari problems

    I have done research on the boards,and so far haven't found a solution so i decided to make my own discussion.
    I have a 2009 mac mini that has run fine until this last month.When comeing out of sleep, the bluetooth magic mouse doesn't work. When i plug in a regular mouse to get me to my destop, everything in the top right toolbar is missing (adobe icon, time machine icon, bluetooth icon, wireless airport bars, and date and time) the search icon is still there, but if you scroll the mouse towards it, i get the not respinding beach ball.... if i go to system preferences, I get the not responding ball of doom as well... If i go to safari, it says i am not connected to the internet, even though when i do a network check, it says everything is up and running, If I go to restart, it just stays on the white screen with the loading circle unil i have to restart by holding in the button.....after the reset, everytihing works fine till i put the computer in sleep again (or logout of my name) .......
    I read that there are bluetooth problems with the mac mini of 2009, but this kind of sounds like more than that.. this hasn't happened before until i updated to LION... but sometimes it sounds like the mini is making a faint "squeaking" sound when it is trying to process things.. this doesn't happen often though... the mini is only 2 years old,almost 3, i can't imigine it dying soo soon... any ideas??? any help would be appreciated... thanks-bruce

    problem solved. Replaced key board, mousse and changed brands of USB bluetooth adaptor, which is now a D-Link brand I bought from an Apple store. Works like a champ.
    Lory

Maybe you are looking for

  • Upload vendor master data long texts to CRM

    Hi I do have the same problem of this thread: [CRM Middleware - R3 to CRM - Long Text transfer |CRM Middleware - R3 to CRM - Long Text transfer] Does anyone know how to upload long texts of Vendor master data to Business Partner mater data? Thanks in

  • What is " factory reset"? How/Why to use it?

    What is the "factory rest" feature?  How and when should I use it?

  • 10g agent Issue

    10g agent was running properly, It's throwing error like ERROR: Max Count Value not set properly in file /opt/oracle/10.2/agent10g/sysman/config/esa/database.properties I dont know which value we have to set? And On GC databases are looking for singl

  • Path login does not start with a "/" character

    I get a "java.lang.RuntimeException: Path login does not start with a "/" character" in my WebApplication. - Http Status 500 - The server encountered an internal error () that prevented it from fulfilling this request. Instead I excepted the site for

  • Storing Image

    Hi friends, Can anyone of you please tell me how can I store a Image file into a table as field. Thanks Indra