Mac Mini firewire peripheral not recognized?

I recently purchased a used Mac Mini and am trying to connect an MBox 2 Pro Firewire audio interface. The M Box 2 Pro is powered and lights up but doesn't show up in the Mac Mini's audio In/Out. I'm using a 9 pin to 6 pin cable. I've been through a number of forums and have tried rebooting and reconnecting in different order, as well as reinstalling Pro Tools 8. USB audio interfaces do appear in the menu but not the firewire...Any help would be greatly appreciated!

check out this article.
additional info here and here.

Similar Messages

Mac Mini (Late 2014) not recognizing SSD OCZ Vertex 2

Hello community,
After days of tests and readings, I turn to you to seek for advice.
Here is my problem:
I am trying to upgrade a new Mac Mini (Late 2014 model) from it's original mechanical HDD to a Vertex 2 SSD I have been using for a few years with no problems to report, great product.
First 1 cloned my HDD onto the Vertex 2 SSD using SuperDuper, all went well.
I then switched disks and set the SSD in the SATA III slot inside the Mac Mini and reboot... the disk would boot, the recovery system and the disk utility would not see the disk (or it would see it just long enough to try to make a disk verification and then would disappear).
Here is what I have already tried:
- Boot from Linux LiveCD, I can see the Vertex SSD, I can see all it's file and browse them
- Reformat the disk, in HFS+ with GUID partition table
- Clean PRAM
- Perform a Hardware Check - all good
- Boot from the original HDD connected through a SATA-to-USB adapter - all good, i can boot the system, but i don't see the SSD drive (or only for a moment then as soon as i try some action on it (like a disk verification) it stalls and then disappears)
- Try to OCZ toolbox to make a security erase and start fresh. I had here a major issue, the OCZ toolbox would not start, it froze after a lot of complaints a "Scanning for hard disk partitions and creating /etc/fstab" and wouldn't move.
- Dissassembled the Mac Mini, removed the SSD, put it in a Macbook Pro, use OCZ Toolbox on it, this time, it loaded perfectly, identified the disk, i did a firmware update to the latest (1.37) and performed a security erase. All went perfectly. For verificiation I rebooted in recovery mode from the Macbook with the SSD and formatted properly the disk using the Apple Disk Utility (GUIP partition table+ HFS+ partition) and the system neatly identified it as a good host for system install. Then i removed the Vertex 2 SSD from the Macbook pro, put it back in the Mac Mini (reassembled it - god, that's a big pain !) and boot it again in recovery, only to see... nothing, the disk is still not recognized by the system.
Voilà... now I'm out of idea, It could be some low level hardware incompatibility, or anything else, i read about TRIM and Yosemite sometime not behaving well, about SATA II and SATA III compatibility problems, but so far, nothing clear.
I therefore welcome in anticipation your knowledge and hope we can figure this out. For the sake of extending the reach, I will also post this on Anandtech and Apple support forums.

Well, thank you tbirdvet, but the problem was actually an incompatibility at the controller level.
To quote the OCZ support :
The issue is incompatibility between the older SandForce 1222 controller used in the Vertex 2 and the newer Intel Haswell platform used in the Late 2014 Mac Mini. The incompatibility started with the Intel 8 and now 9 series chipsets and spans across all products that used the controller regardless of manufacturer. It is expected behavior to be able to connect the Vertex 2 then clone to it, but if you try and cold boot to it the detection will fail. Unfortunately, the Vertex 2 and the controller it utilized are long EOL and never received a firmware update (if that was even possible) to adjust for the release of these new chipsets.
So I can stop looking around it simply wont boot, ever. Product being End Of Support, no new firmware will ever fix this.
So I guess, i'll have to look another SSD.

Mac mini original superdrive not recognizing disk

This happened out of the blue...was reading disks last week, but
had trouble reading a commercially bought cd
and then wouldn't read disk burnt on it.

Thanks for the suggestion.
I will blow out the drive.
I may even try using the lens cleaning disk I have.
But I suspect that you are right, and that it has just given up the ghost.
IT is an old MacMini, but has been such a steady machine.
It is one of the Original MacMinis from 2005/2006!

New mac mini system will not recognize wireless keyboard and trackpad.

My brand new mac mini system will not initialize properly. The return on the track pad are not being recognized, although scrolling is. Any others find this? Support could not figure this out on the phone. They sent me out to get new batteries and now they are closed. Batteries have been changed and still nothing.

My Mac MINI gave me one heck of a time trying to get it to recognize my Bluetooth mouse and keyboard. both Apple brand.
I finally had to connect an old USB mouse and keyboard to get the silly thing to connect.
Don't forget to repair permissions.
I also had to shut the computer down and start it back up a couple of times before it would connect. I think it has to do with the new Bluetooth 4.0 wireless technology.
I also turned off my Bluetooth devices and turned them on again, then I pulled the batteries out a couple of times and tried again and again.
I also put in new battries even thiough the ones I replaced were about a week old.
Finally, the MINI recognised the mouse and keyboard.
I wish I could tell you which thing did the trick.

Mac mini firewire vs Mac pro firewire, trouble with medium format digital back

Hi
I'm trying to use a Mac Mini to run a medium format digital back, I have problems with the connection between the digital back and Mac mini dropping out randomly meaning I have to unplug the firewire and restart the back, sometimes restart the software.
Manufacturer says it is due to Mac mini firewire not supplying enough stable power to the back and to use a powered firewire repeater.
I've tried that it hasn't really made much of a difference.
Manufactuer now says the Mac Mini's are just not up to the job they are significantly diferent to the Mac pro range.
Is this correct?
So I can't use a small form factor mac mini to do a single task - tether to a camera and run camera software. Doesn't really seem that big an ask?
thanks in advance.
Nigel.

you may think it's a single task, but that's on top of the underlying OS processes. also, i'm assuming that your mini is only running a single hard drive, which means your software is competing against the OS for access to the write heads on your drive. have you confirmed that your system memory isn't generating too many page outs? if you're in activity monitor and you see that count increasing, you need more RAM.
you could also try to install a second hard drive in your mini, and designate that drive as your write target for the camera software.
is this for video, or stills?

MAC and iTunes is not recognizing my 5th generation iPod touch with smaller charger plug. What can I do to fix?

MAC and iTunes is not recognizing my 5th generation iPod touch with smaller charger plug. What can I do to fix?

I susopect you have the 5G iPod
iOS: Device not recognized in iTunes for Mac OS X
You need iTunes 11.1 or later and that requires a Mac with OSX 10.6.8 or later

Mac mini server - will not take 4GB so-dimm in bank 0

Mac mini server - will not take 4GB so-dimm in bank 0
Hello,
Memory works ok as long as the old 2gb 1066 so-dimm is in bank 0.
Switching the dimms around is no go. It seems to need that bank 0 populated with an old 2gb.
I can use only one 2gb and one 4gb for the mini server to boot.
It seems to have a hard time figuring out the 2x4gb configuration.
Tried PRAM and NVRAM reset. Always getting 3 beeps.
Any chance of getting the full 8gb detected?

Hi All,
I had the same problem that you, I had a mac mini server late 2009 with 10.7.3 OS X, with 4 GB of memory.
I have got these two memories on amazon:
"8Go mémoire - Kit double canal SAMSUNG original 2 x 4 Go 204 broches DDR3-1066 PC3-8500 SO-DIMM (2x M471B5273BH1-CF8) mémoire portable ordinateur DD"
First test to install in the mac mini:
Slot 0 - 4 GB
Slot 1 - 4 GB
3 beeps
2nd test
Slot 0 -
Slot 1 - 4 GB
OK
3rd Test:
Slot 0 - 4 GB
Slot 1 - 1 GB
3 beeps
4th Test:
1 - 1 GB
2 - 4 GB
OK
5th test:
reset PMU
Slot 0 - 4 GB
Slot 1 - 4 GB
3 bips
6th Test:
I did a test of the 2x4 GB in a mac mini 2010
OK
7th test:
Slot 0 - 2 GB
Slot 1 - 4 GB
OK
After to read this forum I gave up and I decided to let the mac mini with 6 GB. Well, as I wanted to try it again one last time, I tried to put the slot 0 memory forcing a bit. But I did not noticed nothing special.
Well, at this last time, it works. 8 GB in the mac mini server
here some screenshots:
I hope this info will help you to resolve this problem. But seriously, I am not giving you nothing else than hope

Dual Monitors on Mac Mini Late 2014 not working on Dell S2340Lc

Hey guys,
Got a mac mini and using it mainly for work. Working for an ISP and no one has used macs and I've opted to be the poor sucker that gets to deal with old people that don't know how to mac very goodly.
I have two Dell S2340Lc monitors. I have one connected up via HDMI and that works perfectly fine. I turned off the mac, I plugged in Monitor 2 with a MiniDP/Thunderbolt to HDMI adapter, powered on the mac and whilst it was booting, it had the Apple logo and the loading bar on the Dell display plugged in to the thunderbolt to hdmi adapter and then once it loaded up the log in screen, it went to the HDMI display. I logged in and in the displays section, the monitor plugged in to the thunderbolt to hdmi adapter isn't being detected, however I can plug it in to a Samsung 55 Inch Smart TV and it works just fine. I can set up dual monitors between the TV and the monitor in HDMI, but the Dell S2340Lc will only work with a HDMI cable into the HDMI port on the mac mini and will not work through the thunderbolt to hdmi adapter. On the display it just says that there is no signal coming from the computer.
Just wondering if any of you apple gurus had any ideas as to why this isn't working?
Thanks!

What if you switch monitors?
What happens if yo only have the Thunderbolt>HDMI>Dell monitor connected?
Try resetting the SMC and PRAM
Intel-based Macs: Resetting the System Management Controller (SMC)
About NVRAM and PRAM
Call Apple. You get 90 days or free telephone support
Complimentary Support (USA)

Mac mini late 2012 not working with small VGA monitor

I got a mac mini (late 2012 10.8.4 all updates installed) and it is working fine with samsung b2230 via VGA adapter. There is a small VGA monitor (PL8006 max at 1024*768) which works fine when connected to a PC.
When I connect the small VGA monitor to mac mini it is not displaying anything (monitor shows blue screen with letters VGA so I assue it is not getting any signal). Mac's resolution is set to 1024*768 with 60Hz (even tried with 800*600 without any success). Monitor is also not working with win 7 installed in mac mini using bootcamp.
Any thoughts?

i just found that when the VGA cable of the small monitor is slightly inserted into the VGA adaptor it works fine (this is not usable because there is no way to keep the pins at that level) and when the pins inserted fully / moved little it is not working. Since this happens only between these two devices can't find which one is faulty.

After installing osx 10.8.2 to my mac mini it will not recognize my admin account. how do i uninstall

after installing osx 10.8.2 to my mac mini it will not recognize my admin account. how do i uninstall

If 10.7.0 or later...
Bootup holding CMD+r, or the Option/alt key to boot from the Restore partition & use Disk Utility from there to Repair the Disk, then Repair Permissions.
If that doesn't help Reinstall the OS.

Hi, I can't buy Os lion. Mac OS X does not recognized internet addresses beginning buy "macappstore"

Hi, I can't buy Os lion. Mac OS X does not recognized internet addresses beginning buy "macappstore". I did every thing they told me. Repair the disk, and on and on but nothing works. I have a macbook with snowleopard 10.6 and I use safari 5.1
Thanks for your help

I am Ok thank to Dansyacht. I followed the discussion https://discussions.apple.com/message/15720366#15720366
4 days that I fight to find what was wrong. Now I am good.

How to solve: The backup disk image "/Volumes/Data/IP's Mac mini.sparsebundle" could not be accessed (error -1).

Hi,
Please help!
I set up my time capsule yesterday, and it worked perfectly initially. However, after I used the same time capsule HDD as network file sharing with my MacBook Pro and two other PCs, than the hourly backup failed and gave the following error message.
The backup disk image “/Volumes/Data/IP’s Mac mini.sparsebundle” could not be accessed (error -1).
Please help telling me what to do to restore the backup function.
ipmt

First, restart the Time Capsule by disconnecting the power adapter and reconnecting it. If other devices on the network can see it, you can skip this step.
From the menu bar, select
 ▹ System Preferences ▹ Network
Click the lock icon in the lower left corner of the window and authenticate to unlock the settings, if necessary. Click the Advanced button, then select the TCP/IP tab in the sheet that drops down. Click Renew DHCP lease.
Try again to back up.
If you still can't, open the Time Machine preference pane and delete the TC from the list of backup destinations. You may have to unlock the settings by clicking the lock icon in order to do this. Then add it back.

Mac mini firewire

Waiting for my new mac mini to arrive and am trying to get all my cables ready. I have an EHD with firewire 400, will my current cable work with the mini. I have an emac with 400 firewire. My Dell monitor has DVI and HDMI, how should I connect it to the mini. I was planning on using the mini HDMI and run a cable to my Samsung LCD TV when I want to go big monitor style. Any suggestions?

I would actually go for one of these instead:
http://www.amazon.com/gp/product/B002JH3TW8/ref=s9simh_gw_p23_i2?pf_rd_m=ATVPDKIKX0DER&pf_rd_s=center-2&pf_rd_r=0C42MGP0HDBEX8R94Q J7&pf_rd_t=101&pf_rd_p=470938631&pf_rdi=507846
now the reason I say this is because the adapter listed above will be using the port as the fulcrum by which the weight of the adapter and the cable will be applied to. Look at your hdmi to dvi cable on your mini. Notice it is not a straight through connector like the one listed above? That is so the weight of the monitor cable is not applied directly to the port. The Mini Display port adapter is the same way. As was the DVI to VGA adapters that apple used to ship with the G5 mac pro's. Apple is pretty smart about the design of these things, so take a cue from them and get one like I listed above. Because once that fw800 port gets busted from the weight, there is no fixing it unless you solder anew one on or replace the logic board.

External Firewire HD not recognized by MacPro

I have a Thunderbolt Display that works fine. However - i just got a WD 2tb Firewire 800 external drive. I plugged it into the Thunderbolt display and it is not recognized. No matter what i do. If i unplug it from back of display and plug directly into Laptop - it sees it fine.
Fairly new to Mac's so am i missing something? A setting or something?? Thanks for any help.
FYI - laptop is MacBook Pro from 2011 running latest OS.

No, you're not missing anything... it should just work. I have four FW800 drives daisy-chained to my Thunderbolt Display - and they just work. I'm on a 15" late 2011 MBP running 10.8.2 as well.
Something's up - either with your Display, your TB connection or the drive. I suspect the Display or the drive. Is your Display still under warranty? Even if it's not, I would first try it out with a different FW drive (Western Digital is notorious for just not working with Macs) or, if that doesn't work, take the whole unit into your local Apple Store or AASP.
Clinton

Connect 2 Macs w/ Firewire. Not Target disk mode.

I have a PowerBook and an early 09 iMac 24". I used to connected them via firewire to transfer files. Suddenly... the iMac won't recognize the PowerBook... but the Powerbook will recognize the iMac. Actually, the iMac does recognize the PB, but only shows the "drop box" folder.
Is there anyway to configure a firewire connection or something else I might have overlooked? I'm not interested in target disk mode.

Sorry to take awhile to get back to you. I had no experience with connecting two Macs with FireWire, except with TDM. But today I have played around with connecting my iMac and my Mac mini with a FW cable directly.
I assume that you did two things in System Preferences that facilitate this connection; 1. you have created the FireWire network in the Network pane, and 2. you have enabled File Sharing in the Sharing pane. The only other thing to do is make sure that you have selected Bonjour computers in the Shared section of the Sidebar pane of the Finder Preferences.
Then, no matter which style of windows you use for the Finder; icons, list, columns or Cover Flow, you should be presented with a Connect button if you highlight the other computer in a Finder window's Sidebar.

Mac Mini firewire peripheral not recognized?

Similar Messages

Maybe you are looking for