Mac Mini Server for VPN routing

Hi,
my local internet provider does not provide static IP addresses. To nevertheless make the Server available in the internet I found a service that provides a vpn tunnel with a fixed ip address. To connect to this tunnel I shall use "tunnelblick". A pptp configuration is not possible due to some incompatibility on the VPN provider's side.
The Server is connected to an airport extreme, which provides the internet access. I understand that the server has only one network card, however the VPN program uses a virtual network card to connect to the VPN and hence there should be two IP addresses for the server: one for the internal LAN and one for the VPN. How do I figure out the Server's VPN address on my side - or is it the fixed IP address from the VPN provider? 
This IP address can be set as the address for all network devices to go to the internet. How?
I understand there are two ways: the router to the internet is telling all devices on how to go to the internet. Therefore this should be configurable in the airport extreme - how?
Otherwise: How to configure the computers to use this VPN instead of the normal connection?
If it seems to be a simple question however I don't know from where to grab the right answers. I am a newbe in servers ...
Thanks ...
Philippus

The VPN service provides your computer with a private IP address which may or may not be fixed. This gets you to their network... and from there back out to the internet if they haven't blocked that particular IP range. To find out your VPN IP address you only need to open up and take a look at the network preferences status entry for it... Your problem is not there. Your problem is that the Private network ou want to use will be firewalled.. and the ports you need to run a server will not be open to your IP address.
You can share the internet connection of one mac to others in System Preferences I think... can't check atm.. not on my mac.
In any case I suggest, since you do not have a fixed IP.. that you use a DDNS service.. like www.no-ip.com provide and leave the VPN network for what it was intended...

Similar Messages

  • Help Setting up Mac Mini Server for Printer/File Sharing to Windows comp.

    Hi, so in our office, we decided only to switch half of the office to macs for budgetary reasons. We purchased the mac mini server to replace the 5,000 year old one and have also gotten to macbooks and a mac mini. My other two co-workers unfortunately still are using two windows vista machines. We have important documents on the server hard drive and they also need our OLD ACT! database to access from it and I have not been able to get them to access the hard drive. Can someone please walk me through these steps? Also, ideally we want to be able to access this servers hard drive when we are out of the office and edit word documents and such, but I also have not been able to do that or make that work. Any help in these areas would be greatly appreciated!

    If you use a different login name for the network account to your existing local account then the local account will not be affected. You might want to transfer the contents of your existing local account to the new network account. To do this you could try the following
    Create new network account
    Login using old local account
    Now while logged in using old local account - connect to the File Server
    Enter the new login details
    It should hopefully list the Share that stores your new network account, complete the connection
    You should now have the Share mounted, copy the contents of your local account to the corresponding location in your new network account
    Note: The Library folder in your home directory contains all your settings
    Once complete logout of the old local account
    Try logging in to the new account
    In terms of limitations, it is going to be slower than a local account because it has to go across the network, and some badly written applications may have some issues but most will be fine.
    At this stage your local account has not yet been deleted so if you have problems you can revert to it.

  • How do i wipe a late 2012 mac mini server for resale?

    I am wanting to sell my late 2012 Mac Mini Server and i would like to wipe and reset it.

    Before you sell or give away your computer, in addition to the steps mentioned in this support article, take these steps:
    1. Run Apple Diagnostics or the Apple Hardware Test. The buyer will do this (or he should), and you don't want to be surprised by the results.
    2. Reset the PRAM and the SMC, which might contain personal information.
    3. If you set a firmware password, remove it by running Firmware Password Utility in Recovery mode.
    4. If you activated FileVault in OS X 10.7 or later, turn it off.
    5. If you use Boot Camp, the partition must be deleted.
    6. If you created any other data partitions on the internal drive, remove them in Disk Utility.
    7. If the machine has an internal hard drive, erase the one remaining data partition with the option to zero out data. An SSD doesn't need to be zeroed.
    You can't legally or practically transfer any software downloaded from the Mac App Store to the new owner of the machine, even if it was free. That includes OS X, so if you upgraded to OS X 10.7 or later, you must reinstall an older OS, either from the installation media, if applicable, or by starting up in Internet Recovery mode (option-command-R at the startup chime.) If you installed from physical media, deliver those to the new owner.
    If you're selling the machine, or donating it in working order, and it originally shipped with OS X 10.4 or 10.5, then you have the option of installing either from the discs that came with it or from a retail Snow Leopard disc (which you must then transfer to the buyer.) The buyer should understand that if he doesn't get the original discs from you, he won't get the bundled iLife applications or the Apple Hardware Test. Replacements for the original discs can be ordered from Apple.
    The new owner will have to redownload any software that came from the App Store, including OS X upgrades, under his or her Apple ID. If you ever updated the bundled iLife applications (Garage Band, iMovie, and iPhoto) through the App Store, you can't transfer those either. The buyer will have to purchase them.
    Remove the machine from your list of registered products. If it's still covered by an AppleCare Protection Plan, transfer the coverage to the new owner by following the instructions in the AppleCare Terms and Conditions (under the heading "Transfer of Plan.")

  • Setup a Mac mini server for small business

    Im trying to come up with a solution for a families small business.
    theres two of them that operate it out of their home and need something central to access all the company data and documents.
    one travels and one stays back, so the one traveling all they do is forward an email and thats the current documentation they have is in email, no database or file archiving.
    we also want to get their old files and documents scanned in and accessible too, instead of digging through boxes of stuff.
    they also would like remote access while on the road to access their data, i presume they may use macbooks and possibly iOS devices.
    I was thinking a mac mini, and an airport/time capsule for backup purposes and remote accessibility.
    any suggestions on file management and remote access?
    thank you!

    Thanks for those suggestions.
    They need file sharing on the road, away from the home office. I think I understand the concept, but aside from my own personal set-up of OS X server and back to my mac type things, its not really business-y in my opinion to offer them.
    Unless they believe it will good enough.
    So how would i set-up dyDNS? i have a test system i can work with if there are steps you'd recommend?
    I just want to offer them a way to access their documents while traveling to sites through the Apple ecosystem.
    BackBlaze, i hear about this, my only concern is if this company disappears then what? yknow. Crash plan is a nice alternative, but I'm looking for inside the Apple box methods here if possible.
    i really appreciate the ideas.

  • Setup VPN on Mac Mini Server running OSX through a BT Hub Router

    Hello everyone,
    I know this question has been posted several times and I have looked at the suggested solutions, trying each of them. I think this is really down to my lack of knowledge hence hoping someone out there could point me to the right direction for more resources / information, please.
    I am trying to setup a Mac Mini Server with VPN access. My server sits behind a BT Hub router. These are the steps that I have been through:
    1. I am using the server app and after registering a free account with no-ip, I got myself a host name <myname>.ddns.net.
    2. Then I setup the server using a domain name
    3. I configured the DNS by first setting up a primary zone - zone: ddns.net. Then added machine record host name: <myname> pointing to my server which I have configured my router to assign a static ip address to it at 192.168.x.x
    4. Then, I configured the VPN setting up for L2TP and PPTP, setup the shared secret, change the ip address range to match that of the DHCP range on my router. My router by default has a DHCP range between 64 - 253.
    5. Then, I also configured my router to port forward 500, 1701, 1723, and 4500 to my server at 192.168.x.x (I selected both TCP and UDP).
    6. Finally, setup a user account with account name test and password abcd12345
    7. Gone on my "client" machine which is basically my Samsung S4 handphone, selected VPN -> PPTP -> server address: <myname>.ddns.net -> entered account name test and password abcd12345.
    This didn't work.
    Then, I read some post about manually configure DHCP on the server app. Went on the server app, turned on DHCP and setup a network named TestDHCP. Assigned ip address range between that of the default DHCP range on my BT Hub router.
    This does not work either.
    Could someone please kindly help me with it? I am completely lost.
    Thank you in advance.

    To run a public VPN server behind an NAT gateway, you need to do the following:
    1. Give the gateway either a static external address or a dynamic DNS name. The latter must be a DNS record on a public DNS registrar, not on the server itself. Also in the latter case, you must run a background process to keep the DNS record up to date when your IP address changes.
    2. Give the VPN server a static address on the local network, and a hostname that is not in the top-level domain "local" (which is reserved for Bonjour.)
    3. Forward external UDP ports 500, 1701, and 4500 (for L2TP) and TCP port 1723 (for PPTP) to the corresponding ports on the VPN server.
    If your router is an Apple device, select the Network tab in AirPort Utility and click Network Options. In the sheet that opens, check the box marked
              Allow incoming IPSec authentication
    if it's not already checked, and save the change.
    With a third-party router, there may be a similar setting.
    4. Configure any firewall in use to pass this traffic.
    5. Each client must have an address on a netblock that doesn't overlap the one assigned by the VPN endpoint. For example, if the endpoint assigns addresses in the 10.0.0.0/24 range, and the client has an address on a local network in the 10.0.1.0/24 range, that's OK, but if the local network is 10.0.1.0/16, there will be a conflict. To lessen the chance of such conflicts, it's best to assign addresses in a random sub-block of 10.0.0.0./0 with a 24-bit netmask.
    6. "Back to My Mac" is incompatible with the VPN service. It must be disabled both on the server and on an AirPort router, if applicable.
    If the server is directly connected to the Internet, see this blog post.

  • Mac mini server, Snow Leopard, Linksys E4200, 802.11n

    Hi,
    I have mac mini server and wifi router linksys e4200.
    Something goes wrong after software update on mac mini. For clarify I updated a firmware on E4200 too but I think that is not a problem.
    Now I can't get full speed from 802.11n mode.
    My download speed extemely decreases from 160Mbit(always before update) to 27Mbit
    My router supports 3 modes of 802.11n
    1. Mixed
    2. Only Wireless-A
    3. Only Wireless-N
    It always was in mixed mode on 802.11n befare. That's mean it supports b/g/a/n
    I switched it to 'Wireless-N' and can't get it work. My mac mini shows me the wifi network but it can't connect to that network.
    Then I turned my router in Wireless-A. Now I can connect to wifi network but my download speed always no more 27Mbit
    Also these results I see in Mixed mode.
    As I understand my N mode does not work.
    Another strange thing the System profiler shows me that my AirPort does not suppor N mode.
    How to fix it?
    Regards
    Software Versions:
      Menu Extra:          6.2.2 (622.2)
      configd plug-in:          6.2.5 (625.6)
      System Profiler:          6.0.1 (601.1)
      Network Preference:          6.2.2 (622.2)
      AirPort Utility:          5.6.1 (561.3)
      IO80211 Family:          3.2 (320.1)
      Interfaces:
    en1:
      Card Type:          AirPort Extreme  (0x14E4, 0x93)
      Firmware Version:          Broadcom BCM43xx 1.0 (5.10.131.42.4)
      Locale:          FCC
      Country Code:          RU
      Supported PHY Modes:          802.11 a/b/g
      Supported Channels:          1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 36, 40, 44, 48, 52, 56, 60, 64, 100, 104, 108, 112, 116, 120, 124, 128, 132, 136, 140, 149, 153, 157, 161, 165
      Wake On Wireless:          Supported
      Status:          Connected
      Current Network Information:
    Regul-2.4Ghz:
      PHY Mode:          802.11g
      BSSID:          c0:c1:c0:e8:df:1e
      Channel:          1
      Country Code:          RU
      Network Type:          Infrastructure
      Security:          WPA2 Personal
      Signal / Noise:          -45 dBm / -94 dBm
      Transmit Rate:          54
      Other Local Wireless Networks:
    Regul-5Ghz:
      PHY Mode:          802.11n
      BSSID:          c0:c1:c0:e8:df:1f
      Channel:          36,1
      Network Type:          Infrastructure
      Security:          WPA2 Personal
      Signal / Noise:          -43 dBm / -88 dBm
    System Version:          Mac OS X Server 10.6.8 (10K549)
      Server Configuration:          Advanced
      Kernel Version:          Darwin 10.8.0
      Boot Volume:          Server HD
      Boot Mode:          Normal
      Computer Name:          rusik
      User Name:          Rusik (rusik)
      Secure Virtual Memory:          Not Enabled
      64-bit Kernel and Extensions:          Yes
      Time since boot:          1:24

    Thanks for answer
    So please tell me does my Mac mini server supports 802.11n or it supports only a,b,g modes?
    From the specs for this Mac mini
    Wi-Fi wireless networking (based on 802.11n specification; 802.11a/b/g compatible)
    model MC438LL/A
    intel core 2 duo 2.66Ghz
    2010 edition

  • Mac mini server as AP

    Hi, recently I've been thinking about building SOHO router/server based on Intel NUC and Linux but then it stroke me. It would be nice if I could use Mac mini Server for that! So now I'm looking for someone with good knowledge of both Server.app and Mac mini possibilities to find if it would be even possible. First of all: is it possible to turn Mac mini server to access point with RADIUS server? That would go over basic 'internet connection sharing' built into every OSX but theoretically shouldn't be impossible, right? We have all required hw and sw in one place (well, I wasn't able to find ANY performance tests of shared connection from Mac against let's say, Airport Extreme but one task after another).

    Hello John, MrHoffman. This is exactly why I started this thread, thank you. I don't want to extremely customise OSX or something, I've got Linux for that. It's just that OSX is my OS of choice whenever possible. Because I don't have any experience with Server.app I'm simply not aware of what it can do (and didn't want to find out by spending 20 bucks just to see the thing).
    Now, I like streamlined and elegant solutions (that's why I'm here at Apple's in the first place) so I adored the idea of having one tiny box doing all the heavy works like routing, wifi, packet filtering, DNS, time capsule, mail/file/media/print server...and I'd surely come with more ideas during time. And as I said, with Mac mini we have all required tools both hw and sw in this one awesome box, so I guess it's more like business decision from Apple side. Maybe one day, in the future, as we see consolidation of features lately... I don't want to mess around with Synology or some homebrew Cortex based board even though I know how, I'll definitely stuck with x86. So I have two options I guess. Buy Mac mini and Airport extreme, do click here and click there and have all this in two boxes, or build that unified solution from scratch on Intel NUC and Linux. That would take days and nights but it would be also fun (and tears and sweat) and also mostly educative.

  • RAID on Mac mini Server (2011 i7)

    I just purchased a new Mac mini Server today (the base configuration 2011 Quad Core i7 with 4GB RAM and 2x 500GB 7200RPM magnetic hard disks) and wanted to share what I've learned about setting up RAID on the system.
    First, as you may have heard, the Mac mini Server does not include any installation/reinstallation media (I was hoping for a USB reinstall key, but it seems that the new systems don't include these or optical discs; last year's Mac mini Server included handy reinstall DVDs even though the system didn't have an optical drive).  Out of the box, the new Mac mini Server has Mac OS X Lion, the iLife suite, and the Mac OS X Lion Server tools pre-installed on one of the two 500GB internal drives; the other disk is formatted as a separate, second drive.
    If this is the configuration you're looking for, you're good to go right out of the box.  As an aside, this shipping configuration is ideal for using the second disk as a Time Machine drive.  I would argue that Time Machine would be a better use of the second volume than a RAID 1 configuration, as Time Machine provides versioned backups and you don't incur the write performance penalty RAID 1 requires every time data is saved to the disk.  I would further caution that, while an internal Time Machine disk is a convenient safety measure, any critical data should be backed up outside of the system as well.
    Now for those like me who were intrigued by the opportunity to mate the Quad Core i7 with a RAID 0/striped configuration for a performance boost (or if you want to use RAID 1), a RAID configuration is possible, but it there are a few caveats.
    First, Apple has two recovery options for the new Macs: a small hidden recovery partition on the boot drive and their Internet Recovery system.  While it's possible to boot other systems from a Lion installation DVD extracted from the App Store Lion installer, such bootable optical discs will not boot the Mac mini Server at this time (this may change if Apple modifies the App Store Lion installer).  Therefore, as of right now, the recovery partition or the Internet Recovery system are the best options for installing/reinstalling on a RAID set.
    Second, if you boot the system using Command+R to access the recovery partition, you can wipe the two drives and create a RAID set, but this process will remove the recovery partition and is incompatible with FileVault encryption (a warning to this effect comes up when you try to start an install/reinstalll on a RAID set, but at that point, you've likely already erased the recovery partition in Disk Utility).  If the system boots after the recovery partition is deleted, the only install/reinstall option is Apple's Internet Recovery.
    Third, as might be expected depending upon your internet bandwidth, the Internet Recovery system can take a while to boot the recovery tools (10-15 minutes to boot on a standard cable modem connection) and to reinstall the OS (50+ minutes on a standard cable modem connection).  Internet Recovery currently reinstalls only Mac OS X Lion and the Server tools on the mini Server; there's no option to install iLife during the OS install (Apple could always change this by updating their servers, and there is a Customize button on the installer, but it is greyed out and cannot be clicked at the present).
    Fourth, once the OS is reinstalled, it's possible to reinstall the iLife applications by launching the App Store from within Mac OS and selecting Purchased.  The store will indicate that the system is eligible to download the iLife apps and you can do so by agreeing to upload system-identifying information to Apple and signing in with your Apple ID.
    I hope all this helps.  Here's a more concise step-by-step of how to set up the system with RAID:
    THINGS YOU NEED
    A fast Internet connection for the mini
    Patience
    Hold Command+R on the keyboard at start up to boot from the system's recovery partition (if the recovery partition has been deleted, the system should start from Apple's Internet Recovery system; you may need to connect to WiFi if wired ethernet isn't available)
    Once you get into the recovery utility, select Disk Utility and for each of the two hard drives:
    highlight the drive
    select the Partition tab
    select 1 Partition from the Partition Layout pulldown menu
    select Free Space from the Format pulldown menu
    click Apply
    After you've wiped both of the drives, highlight one of the disks and click the RAID tab, then create a RAID set (striped or mirrored, as you prefer)
    Quit Disk Utility and from the main recovery utility menu select Reinstall Lion (from this point on, if you have any trouble, you can restart the mini from the Internet Recovery system and return to this point, but the recovery partition will be gone as long as you keep the RAID set)
    After you install and configure Mac OS X Lion Server (which can take well over an hour to download and install), you should be able to reinstall the iLife applications by launching the App Store App and selecting Purchased, then logging in with your Apple ID and agreeing to send your system info to Apple to download the iLife Applications
    If you're using the mini as a production server, I highly suggest setting up some local, external recovery tool, as you don't want to have system downtime protracted by having to wait for an Internet Recovery boot/reinstall.  I would also beg Apple to consider this sort of scenario and to provide more supported methods for recovering and reinstalling from local media.
    Best of luck to you all.

    I found the basic principle on another forum thanks to a guy called 'e-whizz' and this what I did to make RAID 1 work on a mac mini server with LION server.
    You can easily configure the second drive on a mac mini server for a Mirrored RAID 1 set with Lion Server without either reinstalling or erasing your existing setup.
    The initial setup process takes about 30 minutes, though the rebuilding of the mirror disk will take several hours, depending on the amount of data you have on the drive. It took around 3 hours on a new mac mini server with lion server installed, nothing else configured.
    Before you start, please ensure you have a current backup of the server. Getting the following commands wrong can render you server unusable.
    What you need to use is the command line version of Disk Utility, diskutil.
    Before you start, clone the hard drive. You can use SuperDuper (or similar, I have used SuperDuper) with copying all files onto a USB memory stick. If Lion is freshly installed, 8Gb will do. SuperDuper will create a bootable copy on the USB.
    Boot the mac mini from the external USB. To do that, reboot and hold down the option key while restarting. You will see a window, select the USB drive to boot from.
    Launch the terminal and type the following command:
    diskutil list
    This gives you a list of all the drives and partitions your system knows about.
    You need to find the Server HD partition (the first disk) and the HD2 partitions (the second disk). These are the two main ~500GB drives. You will be using the disk IDENTIFIERs when issuing the diskutil commands. For a stock standard Mac Mini Server, the commands below are correct, but if you have previously changed the volume names, or repartitioned at any stage the disk identifiers and volume names may differ.
    First enable RAID mirroring on existing Server HD volume. This will create a single disk, unpaired mirror, without affecting your data.
    Using this syntax:
    diskutil appleRAID enable mirror disktomirror
    where disktomirror is your disk identifier for Server HD
    On my mac mini server, Server HD was disk0s2, so I used this command:
    diskutil appleRAID enable mirror disk0s2
    You now need to run diskutil list again to see the disk identifier for the new RAID volume. The new RAID volume will be listed as disk# on its own at the bottom of the list.
    On my mac mini server this was disk3 (disk 2 was the USB I booted from, disk 0 the first disk and disk 1 the second disk)
    Next add the disk HD2 to the Server HD raid mirror volume (on my mac, as I said before, this is disk3) as a new member.
    This step will erase disk HD2 and begin an auto repair of the Server HD.
    Using this syntax:
    diskutil appleRAID add member newdisk raidvolume
    replacing newdisk and raidvolume with your particular disk identifiers
    On my server this was:
    diskutil appleRAID add member disk1s2 disk3
    To follow the progress of rebuilding the mirror set, type
    diskutil list
    It will show you the progress in % of the rebuilding under status
    Once finished, reboot and your RAID 1 is up and running and you have also a working backup on your USB (coz' that's where you booted from ;-)
    After reboot you can check the status of your RAID with
    diskutil appleRAID list
    Both drives should show ONLINE under status, interestingly, the device node for the RAID changed on my mac mini server from disk3 to disk2
    That's it

  • Mac Mini Server auto commands

    I use a mac mini server for FTP, the is put to sleep at night when i wake the server i need t
    enter the following sudo commands to allow my clients to access
    sudo ipfw l
    password
    sudo ipfw -q flush
    i am looking for a solution to automate the entry of these commands on wakeup of the server
    also i would like to be able to remotely wake up the server from my iphone or imac
    and auto run the sudo commands
    any help on how to achieve this would be greatle appreciated

    You could simply create a cron task such as those that perform the nightly, weekly, and monthly maintenance tasks.
    You could search here, CNet Downloads or MacUpdate, for an existing utility that enables you to perform an action based on a system event such as, Do Something When.

  • Mac Mini & Mac Mini Server

    Hi
    I would like to know the "suitability" of Mac Mini or Mac Mini Server for web hosting (multiple domain/site) purpose. Some basic assumptions include : budget less than USD$5, user base / concurrent access less than 500, hosted at data centre with average bandwidth (not sure at the moment though).
    Basically, I am disappointed with the purchase experience with Windows server. I have ready cash but the reseller seems no so keen. Perhaps, I am not the big spender. I wanted Windows server is because my developer is "brained-wash" in Windows world. He uses the standard PHP, mySQL related stuff. So I am trying to "brain-wash" him to Mac but it's a challenging task for me with little knowledge on the subject matter.
    I need to know if Mac Mini and or server is "powerful" as compared with Windows server. I know it is not a very "fair" question but if I know there is very few people use such, then I more or less know the answer.
    HTH.

    Some things to consider. 
    The mini server will consume low power, generate little heat, and can be packed densely into a data center, achieving high levels of clustering or redundancy.  The flash storage is plenty fast but not spacious.  They are also cheap enough to buy two to form a level of redundancy, especially if you are using a load balancer.
    However, Mavericks Server no longer includes MySQL.  This download you must do yourself.  PHP and Apache are present but Apple is not always the fastest to patch these two products.  You can replace the stack with a MAMP install which might serve you well.  Server.app does not expose all the Apache features that a hosting service may want/need.  However, you can edit the conf file manually.  If you are planning on giving your customers remote access, FTP is hobbled in Mavericks and you need to do a ton of work (or buy something else) to get multi-tenant chroot.
    Regarding "powerful"... If you are using the device for a single task, then the issue falls to the performance of the network card in comparison to your internet connection speed.  If you are getting a 100 MB connection then the possible concurrent requests will never saturate the server.  This assumes that your HTML and images are optimized and you are not sending out a bunch of 1 MB GIFs.  Also, the consideration is Apache vs IIS.  Apple provides Apache and a simple interface for "casual" web services, usually one site or to support its own services.
    Keep in mind that there are many Linux solutions that exist in which the cost of hardware might be equal to or less than the mini.  And in this case, you are getting the raw LAMP stack that you can more fully customize and patch.
    Reid
    Apple Consultants Network
    Apple Professional Services
    Author "Mavericks Server – Foundation Services" :: Exclusively available in Apple's iBooks Store

  • External HDs NOT showing in finder on Mac Mini Server

    On my brand new mac mini server. for the life of me, I can't work out why my 3 external firewire plus the thunderbolt drive we use as the actual drive we all connect to one the network, just will not show either on the desktop OR in the left column of the finder?
    I have gone into finder preferences and selected External disks and no joy. am I missing something?  In fact, I'm fairly sure that at least the thunderbolt HD was showing when I first got it a week ago with teh mac mini.?
    Superduper and disk utility CAN see them and this is the ONLY way I can do a safe eject currently as I have no other way to eject.
    What might be happening do you think?

    Hi Antonio, did you ever try this?
    https://discussions.apple.com/message/21061564#21061564

  • Can't connect to Mac Mini Server

    I am setting up a new Mac Mini Server for the first time and cannot connect to it from the local network. The Mini is connected to the local network and the internet via an Airport Extreme Base Station. The server appears in the Finder of my MacBook Pro under "Shared" but will not connect. I was able to connect prior to turning on some services in Server Admin (including enabling the Firewall). I allowed the server to control the Base Station upon initial setup but was not sure if it configures and turns on it's firewall services automatically. Should I have Firewall enabled in Server Admin?

    Blankfer,
    Did you re-enable Firewall in Server Admin and then open the screen sharing ports?
    I'm still confused as to whether the Firewall in Sever Admin is only supposed to be used when the sever is acting as an internet gateway. I was under the impression that the Mini was controlling my Airport Extreme's firewall services for me in the background. After my initial configuration through Setup Assistant (including selecting the option to have the server control my Airport) the Firewall in Server Admin was not enabled. Does Firewall being disabled in Sever Admin mean I have no firewall up at all? ...I plan to have it running web and mail services so I need to make sure it's secure.
    -Thanks

  • New mac mini server won't start up

    Hi I've had the new Mac mini server for 2 day now and it was workinf fine untill I tried to restart it. When I turn it on I just get the apple logo and the gray processing wheel.
    I've have used disc utility to check the disc. But that did nothing.
    It is picking up the startup disc fine.
    Is there anything I can do or will I need to re-install.
    Any help would be appreciated.
    thanks

    Greetings Richard, I ran into a similar situation recently with my mini server. although I believe it to be a problem of my DNS settings getting hosed. I couldn’t log in no matter what log I used-even as the root user.
    I had a back up on the second drive of the mini. I did buy the USB drive when I bought the mini, so I was able to boot off the install disc. Then from the menu I choose the back up partion as the start up drive. After restarting, I was at least able to recover and copy my important files to the back up partition. I have not been able to work out the login issue yet. I’ll probably just do a reinstall on the corrupted drive.
    In any event, it maybe worth it for you to buy the USB drive and boot off of it.
    The verbose mode is for you to be able to login through the command line and trouble shoot from there.
    Also, in safe mode, any files that you may want to change permissions, you may need to change the owner and then change the permissions. This is done with the chown command and then chmod command. You’ll need to use the sudo command so you can become the root user to use the commands and make any changes.
    Hope this will at least help you get further in troubleshooting this issue.
    Bill B

  • Mac mini server and media center

    I recently purchased a Mac Mini Server for a few reasons.  One being to put all my music, video and photos on it and play it on my TV via the HDMI cable.  I also want to share that music, video and photos with my wife and my daughters over the network.  
    So mainly one video, music and image library shared with a MBP an 3 MB's on my network.  
    Also most if my video is from our iPhones.  
    I'd also like to put all my home movie DVDs onto the server as well.  
    Ideally all the data on the server can be played on the TV and all 4 Macs at the same time and it will be organized and easy to access.  
    Any ideas of what I should do?   I know iPhoto won't let more then 1 user at a time have access so that's out.  
    If you have any ideas that would be great.  
    Thanks,
    Darren   

    iPhoto should really just be for still images. I don't think the automatic media scanner expects to see videos there. (This would be true of most 3rd party media center applications).
    For further assistance, you might wish to consult on the Plex Forums on their website. I'm sure your feedback there would be appreciated.

  • Mac Mini Server Backups

    Dear all,
    I am using a Mac Mini Server for filesharing, iCal, etc. I want to make sure all data is safe, so I want regular backups. The Mac Mini Server is set up to work on Disk 1 and backup on Disk 2. But in case the server is stolen, crashes or something similar this set up is pretty useless.
    Therefor I am investigating different possibilities to back up safely. I have two option I want to investigate further, however I'm not sure what's possible and what not.
    1. I have a second Mac Mini Server available. Is it possible to have the primary Mac Mini Server backup on the secondary Mac Mini Server?
    2. Is it possible to run backups on an external server? E.g. FTP.
    Thanks in advance!
    Nick

    This is what I would do.
    I would repartition the server to use software RAID 0.
    What this would do is mirror both hard drives. Lets say one day that one of the hard drives failed, its ok because all you would have to do is put a new hard drive in and you are back online.
    This means you will not have to deal with any down time.
    For backups you could run Carbon Copy Clone to an external hard drive. This will make an exact clone of your hard drive that you can even boot too!
    You can bring this off site for better data protection.

Maybe you are looking for