Mac Mini Superdrive won't feed disk

Recently my mini stopped accepting disks. This occurred just after reading and ejecting a disk. I've attempted pushing the disk slightly hard into the drive, ran disk utility, ran apple hardware test... all with no success.
Does anyone have any suggestions or have you run into similar problems?
Listed below are my specs.
Thanks!
Mac OS X v 10.6.8
Model Name:    Mac mini
Model Identifier:    Macmini4,1
Processor Name:    Intel Core 2 Duo
Processor Speed:    2.4 GHz
Number Of Processors:    1
Total Number Of Cores:    2
L2 Cache:    3 MB
Memory:    2 GB
Bus Speed:    1.07 GHz
Boot ROM Version:    MM41.0042.B00
SMC Version (system):    1.65f2
HL-DT-ST DVDRW GA32N:
Firmware Revision:    KC08
Interconnect:    ATAPI
Burn Support:    Yes (Apple Shipping Drive)
Cache:    1024 KB
Reads DVD:    Yes
CD-Write:    -R, -RW
DVD-Write:    -R, -R DL, -RW, +R, +R DL, +RW
Write Strategies:    CD-TAO, CD-SAO, CD-Raw, DVD-DAO
Media:    To show the available burn speeds, insert a disc and choose View > Refresh

Reset the SMC
Intel-based Macs: Resetting the System Management Controller (SMC)
1. Shut down the computer.
2. Unplug the computer's power cord.
3. Wait fifteen seconds.
4. Attach the computer's power cord.
5. Wait five seconds, then press the power button to turn on the computer.
The PRAM
Resetting your Mac's PRAM and NVRAM
1. Shut down the computer.
2. Locate the following keys on the keyboard: Command, Option, P, and R. You will need to hold these keys down simultaneously in step 4.
3. Turn on the computer.
4. Press and hold the Command-Option-P-R keys. You must press this key combination before the gray screen appears.
5. Hold the keys down until the computer restarts and you hear the startup sound for the second time.
6. Release the keys.
Then if it still not working, contact Apple Support, your local Apple Store or Authorized Apple Service Provider and have it serviced.
Apple - Support - iMac - Service FAQ

Similar Messages

My Mac Mini will not read TDK disks from my iMac G3.

My Mac Mini will not read TDK disks from my iMac G3.
I used an iMac G3 (2001) -- the ones that looked like a big pod -- running on OS X and saved files to TDK CD-R, 700 MB disks, which worked fine. Now that I have a Mac Mini (model number A1347) I cannot get this computer to read those disks, made on the iMac G3. Once inserted each disk will open and I can retrieve files for a short period, then the problems start. The computer makes some noises, the beach-ball/pinwheel goes around and I cannot get the files to open or the disk to eject. After a while the disk does eject -- to my relief. I keep using Control+E until ejection happens.
My Mac Mini (2010-2011) is hooked up to a View Sonic HDMI LED monitor, an iOmega external hard-drive for backing up, an Epson Stylus C88 Plus printer and to the internet by a fibre 10MB feed. The Mac Mini runs on OS X version 10.6.8 Snow Leopard: Processor Speed:2.66 GHz
I took the Mac Mini to an Apple retailer and he hooked the computer up to one of his monitors and it read the TDK disks just fine. I am now using Sony CD-RW, 700 MB disks, but I would prefer to use my TDKs because I have such a large pile of blank ones to use and there are those TDK disks with information that I want to look at from time to time. Can anyone tell me what to do?
DJG

Try disconnecting everything attached to the Mini except the monitor.
If that doesn't work, try setting up another admin user account to see if the same problem continues. If Back-to-My Mac is selected in System Preferences, the Guest account will not work. The intent is to see if it is specific to one account or a system wide problem. This account can be deleted later. If successful, copy the files to the original account Public/Dropbox.
Isolating an issue by using another user account
If the problem is still there, try booting into the Safe Mode using your normal account. Disconnect all peripherals except those needed for the test. Shut down the computer and then power it back up after waiting 10 seconds. Immediately after hearing the startup chime, hold down the shift key and continue to hold it until the gray Apple icon and a progress bar appear. The boot up is significantly slower than normal. This will reset some caches, forces a directory check, and disables all startup and login items, among other things. When you reboot normally, the initial reboot may be slower than normal. If the system operates normally, there may be 3rd party applications which are causing a problem. Try deleting/disabling the third party applications after a restart by using the application un-installer. For each disable/delete, you will need to restart if you don't do them all at once.
Safe Mode - About
Safe Mode

How do I use a Mac Mini + Airport Express + Time Machine disk to backup another iMac

How do I use a Mac Mini + Airport Express + Time Machine disk to backup another iMac?
The question pretty much says it all.
I have a Mac Mini with an attached 3TB Hard Drive used for Time Machine Backups.
I have an Airport Extreme base station which services that machine plus several others.
I would like to backup my new iMac and a MacBook Pro to the Mac Mini.
What do I need to do on the mini to export that hard drive so that it can be used as a Time Machine target from the other systems?
All systems are running 10.6.8.

Well you would have to do backups over a network which is much slower and has highest chance of becoming corrupt. I think your best option would be to get an apple time capsule to act as a network and back if thats how you wanna do that

MacPro backed up to Time Machine, added Mac Mini now get "The backup disk image "/Volumes/Data/Jerry Booher's MacBook Pro.sparsebundle" is already in use." error when Mac Pro tries to back up

MacPro backed up to Time Machine, added Mac Mini now get "The backup disk image “/Volumes/Data/Jerry Booher’s MacBook Pro.sparsebundle” is already in use." error when Mac Pro tries to back up

It is standard Mountain Lion error due to the networking ability which is comparable to wet string. (actually that was lion.. it dried out some with Mountain Lion.. higher in the hills perhaps!!)
See C12 and C17
http://pondini.org/TM/Troubleshooting.html
But many people are suffering the same issue..
And the above is even a little out of date.. you might need to do a reset to the TC.
Welcome to Apple's beta program for everyone.

Mini 2010 SuperDrive won't read disks

I have the 2010 Mac Mini Core 2 Duo edition with an optical drive. I have had it replaced once through Future shop extended warranty, but again it is failing to play any disks. I will take the disks in, make a few noises then after 15-20 secs, ejects them. Am I fighting a never ending battle here each time I get the drive replaced?
I'm running 10.9.4
Is there a common failure point with these models? (hence maybe why apple decided to go without for 2011+?)
Any help would be appreciated.
Thanks,

Apple Computers: Troubleshooting the slot-loading SuperDrive
Yes the slot-loading drives are failure prone.
I replaced the the one in my 2009 Mini last year with an LG external drive.
The Apple USB external SuperDrive drive does not easily work with Minis that have internal drives. Commercial external ones are also less expensive.

Mac Mini Slow & Won't Recognize CDs

A classmate of mine is having issues with his Mac Mini, early 2009 model & was looking for advice. He is curious if there is anything he can try before he takes it to the Apple store as he runs his music business from it.
It's a Mac Mini, March 2009
OS 10.5.8 (he thinks)
C2D 2GHz
1GB RAM
120GB HDD (only 9.5GB free according to him)
nVidia 9400M (128MB shared he thinks, not sure)
He says that he installed VM Ware Fusion on it with a dynamic partition. It seems that the unit runs slower when the VM is not running than when it is. (Yes, I agree that's odd.)
His specific question is 'what free defrag programs exist for mac?' I explained it's not entirely necessary and that might not be his issue.
Also when he attempts to burn CDs the first discs he uses won't read. He'll reboot & it will see the disc fine in Disk Utility & Finder. Once that happens he can burns discs at his leisure (until the next time he reboots without a disc in the drive).
Any advice for him before he brings it in?

I actually talked more to him & one of my coworkers. He said that, in fact, he's got 4GB of RAM as he had it upgraded (after purchase). My class mate said he uses a program called Fruity Loops 9.0 (I've never heard of it) to mix his songs & that it would get choppy when (like a skipping CD) during playback once compiled.
My coworker said that he knows Fruity Loops & says that it's a processor-intensive task. He's only seen it perform well on PCs with dual cores at 2.5GHz & up, or MacBook Pros, Mac Pros, & iMacs with 2.4GHz & up. He also said that the disc drive may need a firmware update as he's seen Mac Minis get flaky without the right update.
Once he's gone through all those suggestions I'll report back.
Thanks Ian!

Mac Mini G4 won't boot; fan full blast . . .

Hello!
I was using my G4 Mac Mini when it decided to re-boot itself, and on start-up, all I heard is 1 loud whrrring sound from the fan, a short pause, followed by continuous whrring sound from the fan going at full blast (very loud!). The screen shows nothing.
I've tried the troubleshooting steps in the Apple site but nothing seems to work. Each time I start it up, it does the same thing.
A few months back I'd the unit repair under warranty by Apple (replaced logic board). So it's quite frustrating to have it down again - and now it's out of warranty.
Any ideas?
Thanks.
Mac Mini G4 Mac OS X (10.4.8)
Mac Mini G4 Mac OS X (10.4.8)

It's perhaps telling that the problem occurred after the system forced a reboot. That tends to suggest there's a significant fault - likely hardware, since if the issue was with MacOS it would not be likely to cause the fan to ramp up to full speed on startup with the screen showing nothing.
You mention that you've tried troubleshooting steps, though not which ones. Likely, given that it features in G4 mini troubleshooting of startup issues, that would have included a PMU reset, but if you haven't yet tried that, do so. I would not hold out much hope that it will assist in this situation, but the power manager is the only hardware component that could cause this sort of potential issue, and the only one that can be reset by the user.
Assuming a PMU reset doesn't help at all, and since the system doesn't show any display, it's not worth trying to boot from the original install disk to run the hardware test since the system isn't even managing the power on self test, thus won't move on to loading MacOS. At that point, I'd say you should take the mini to an Apple store if you have one in your location, or to an Apple authorized service provider for them to give you an idea of what is wrong and what it would likely cost to repair it.
If you don't want to do that, the only option is to open the system and examine it yourself. The problem with that, however, is that there really aren't any user-servicable parts inside so other than checking that everything is correctly connected and properly seated, there's really not much else you can do.

Mac Mini fan won't turn off (only while powered on)

Unlike some stories i've read while crawling around the internet trying to solve MY problem, it's not that my fan won't shut off EVER. The fan shuts down when i put it in sleep mode or shut down the Mini. No problems there. But while the computer is in operation, the fan runs non-stop.
It wasn't always like this. In the 2.5 years i've had my Intel Mac Mini, it has more and more frequently employed the fan. As of the last couple months, the fan is now in continuous use, as long as the computer is in operation. In addition, all the programs take much longer to load, and i'm dealing with programs crashing (Firefox & Safari far more than anything), Bluetooth not functioning, and the front light on my Mini is out.
As for the fan, the Mini is getting plenty of breathing room...even more than it had before the problem. I also have 22GB left on my Mini's hard disk.
Are all these problems related? Am i really just working on my last thruster here? Is my dilitium crystal just about dead? Is a warp core breach imminent? I do not have AppleCare, and i don't know if the Apple Store would look at it for free if i brought it in. Any help (no matter how small) would be greatly appreciated.
MY STUFF:
Mac Mini - 1.66 Intel Core Duo, 2G 667 HHz DDR2 SDRAM
Iomega MiniMax 1TB external HD (for audio/video files)
Iomega Minimax 1TB external HD (for Time Machine)
OSX 10.5.6

When you start your mini from cold (after at least an hour powered down) does the fan spin up to full speed immediately, or does it start out normally and then speed up after a few minutes or so? Did you have the system open for any reason just before this behavior started?
If you had the system open, it might be something as simple as the fan control cable that is not connected. When disconnected, the fan will run at full speed all the time.
It the fan runs at full speed almost immediately from cold, then it would suggest one of two things: either the system is suffering from something like a loose heatsink, or there is an errant process running that is putting the system under heavy load. You can check that by opening Activity Monitor (in Applications>Utilities) at looking to see if the CPU load is consistently high. If it is, look for a process that is causing it.
If the fan runs quietly at first, and then speeds up, after a few minutes, then it does seem likely to be a heating issue. Aside from making sure the vents around the base and on the back are clear by using a good vacuum cleaner, it's possible there is enough debris inside to obstruct the airflow. If you've opened up the system previously for any reason, now might be a good time to do so again, for a quick inspection and clean out.
I would also perform an SMC reset if you have not already done so:
To reset the SMC on an Intel mini:
-From the Apple menu, choose Shut Down (or if the computer is not responding, hold the power button until it turns off).
-Unplug all cables from the computer, including the power cord and any display cables.
-Wait at least 15 seconds.
-Plug the power cord back in, making sure the power button is not being pressed at the time.
-Then reconnect your keyboard and mouse to the computer.
-Press the power button on the back to start up your computer.
And to ensure you are not suffering from a range of broad 'tuning' type issues, download a copy of YASU (http://jimmitchelldesign.com/projects/yasu/) and run all tasks. This clears cache files, resets logs files, updates prebinding, performs a permission repair and a few other tasks. After the reboot (which will be slower than usual) your system should run a little better.
... i don't know if the Apple Store would look at it for free if i brought it in....
You can make an appointment at the 'genius Bar' of your local Apple store - they will look at your system for free, and help with a diagnosis. What they generally wont do without charging for it is anything that involves opening the system up. However, it's worth paying them a visit for a bit of hands on work!

Mac mini now won't even turn on

A series of problems started going on with my mac mini intel when I was attempting to burn a DVD:
-I opened disk utility and attempted to burn a DVD (something I've done many times before), only to find the "burn" button was greyed out and it wouldn't allow me to burn anything.
-I inserted a blank DVD only to have the computer spit it out instants later, I inserted it again, and the same thing happened.
-Finiding this really weird, I checked the DVD image I was attempting to burn with the "get info" button on disk utility and found that it was recognizing the archive as being on an external disk, even though it was on the internal.
-I thought there might be a problem with my disk so I verified it, and disk utility told me everything was fine. So I attempted to reapir disk permissions. After about 15 minutes of DU telling me there was "about a minute" left to go, and the status bar going nowhere, I gave up and decided to boot through the mac OS X installation CD (I have 10.5).
-I put the cd in and held "c" and nothing... the computer booted normally. I did it again and nothing. And now I noticed that the computer didn't recognize the disc, and I couldn't even eject it.
-I tried all the solutions presented here for ejecting, including terminal and sticking a business card to loosen it up, nothing worked. I called my father, and he said we had to reset the parameters by reseting the mac and holding ctrlalt+PR and letting it restart 3 times.
-Well... now the mac mini won't even start up... it turns on, but the monitor doesn't even recognize it and no image shows up. It stays like that for as long as you leave it on, so I eventually had to force a shut down, and try again, to no avail. There's a small beeping noise about twice, and then a stronger sound that suggests it's trying to boot, but nothing... and it heats up a lot.
any ideas?

OK, now when I turn it on the light on front doesn't even go on, and it just starts making a loud exhaust noise (like a "vvvvvvvvvvvvvvv"), and the ventilation in the back goes crazy strong... I had to unplug it

Mac mini G4 won't mount music CD after installing Leopard

My Mac mini G4 has some issues mounting music CDs after installing Leopard. I did an "archive and install", everything seems to be working fine, except the CD issue. I have also applied all the relevant updates. I didn't have any issue with CDs in Tiger on this system.
Just after booting, the CD does mount. However, I can't eject it by dragging it to the trash can. I can unmount it only by hitting the eject button on the keyboard.
If I insert the CD again it won't appear on the desktop anymore. It doesn't appear in iTunes either, no matter how often I try.
I noticed someone else in these forums had the exact same problem. The problem was marked as solved, but in fact it wasn't. No information is available in the forum on how to solve it.

This EXACT scenario happens to me. It started the day I upgraded from 10.4.x to Leopard. My workaround is to go into Disk Utility, find the CD (which shows up as unmounted). Click on the CD. Then click the "Mount" button at the top. It works, but I'd like a real solution.

Problem With Mac Mini Superdrive

I recently tried to upgrade my OS to OSX SL. Before I did this my mini was working properly. I placed the disk in and it went through the upgrade no problem. But when I tried to eject the disk it would not come out. I exhausted all possible eject solutions I could find on the web and then some. So I examined the mini a bit and there is a bar that has come up blocking the drive from having other CD's inserted. The drive appears to be working to eject the disc, but just wont. I had to remove the top of the drive to remove the CD. I did get the CD out and now there is no way to insert a disk as the bar still remains up and no disk is in the drive. With the drive top off I can place a disk in the mini and start the computer, the drive reads and plays the disk fine, it just cannot eject. It appears to be a mechanical problem with the drive itself, but I am not certain since this happened as after I upgraded. My question is, is there any way that the upgrade could have not supported my superdrive and this is why this happened (It is an older mac mini bought back in late 2007 it has 1MB of memory which is the min. requirement of OSX SL) ? I could reinstall leopard, do you think this will fix the drive issue or is the drive damaged for some reason?

http://eshop.macsales.com/shop/optical-drives/superdrives/
But there are many.
Or you can just buy an external USB unit.

Mac Mini (PPC) won't boot off install DVD

I'm having a major issue with my 1.24GHZ G4 Mac Mini. What I want to do is reformat the HD and reinstall OSX. But for some bizarre reason the machine refuses to boot off any OSX install DVD I throw at. I've tried Jaguar and Panther as well. If I hold down the C key during reboot and wait for the Apple logo to come up, I get that but it goes no farther. I can hear the drive being accessed (and I know it's not fault because it works fine under OSX) and yet I end up getting stuck at that logo screen. I can reboot the system normally into OSX Tiger.
I also strangely cannot partition the hard drive from within Disk Utility.
Can anyone give advice?

Possible options/questions...
a) Have you tried using the original Install DVD that came with it?
b) Have you tried booting into Single user mode and checked the drive? (Hold down Apple-S until it boots into text mode and when you finally get the prompt type 'fsck -fy' without the quotes).
c) Also, you may wish to try resetting the PRAM immediately before booting from CD. Let it reset THREE times (hold down Apple-Option-P-R or WinKey-Alt-P-R until it has chimed 4 times) and then hold down the C key to boot from your Install DVD.

New Mac Mini+Superdrive+windows 7 - Will it work?

Looking at updating my father to the Apple world, thought I would get him a Mac Mini, and use Bootcamp to install Windows. As the new Mac Mini doesn't have an optical drive (I have a MacBook Air Superdrive), if I use the external one to install Windows, will it install properly? Does the Mac Mini have the drivers for the SUperdrive? Any thoughts? Thanks in advance.
vladimir10

Well, running 10 Mac Apps whilst Paralles is running XP & W7, here's the results, many DirectX tests ran at dizzing 400+++ FPS!?
I'm certain running off a SATA drive would double this.
All on a lowly iMac...
Hardware Overview:
Model Name: iMac
Model Identifier: iMac7,1
Processor Name: Intel Core 2 Duo
Processor Speed: 2.4 GHz
Number Of Processors: 1
Total Number Of Cores: 2
L2 Cache: 4 MB
Memory: 6 GB
Bus Speed: 800 MHz
Boot ROM Version: IM71.007A.B03
SMC Version (system): 1.21f4

FCP runs on Intel Mac Mini, but won't capture to external drive, HELP!!

Installed FCP 5.1 on Mac Mini Core Duo and it runs fine. It will capture fine too, but only to the main harddrive. If I plug in a firewire harddrive using a firewire hub it won't capture, and give a "No Video" error in the Log and Capture window. I've used both popwered and unpowered firewire hubs, and even tried daisy chaining the camcorder off the harddrive. Nothing has worked. And there is no space on the main harddrive to capture to.
I know there is a lot of speculation about whether FCP would even run on a Mini, but it will. If only I could capture it would be a reat capturing station. Has anyone had success? Its pretty frustrating as I've used the Power PC Mac Mini for capturing in FCP 5.0 without any problems. Why would apple make the new Mini crapier?

Never use FW hubs when capturing video. They only lead to grief.
Some cameras, particularly Canons, refuse to share the FW bus with anything. Could this be your problem?
If so, there is little I can think of to do with a Mini (or an iMac for that matter) beyond capturing from a different deck/camera that is more social than the Canons and their brethren. You only get the one FW bus.
But first thing to try is to get rid of the hub. Hook your fw drive to the computer and your camera to the FW drive.
Post back,
Patrick

FCP runs on Intel Mac Mini but Won't capture, HELP!

Installed FCP 5.1 on Mac Mini Core Duo and it runs fine. It will capture fine too, but only to the main harddrive. If I plug in a firewire harddrive using a firewire hub it won't capture, and give a "No Video" error in the Log and Capture window. I've used both popwered and unpowered firewire hubs, and even tried daisy chaining the camcorder off the harddrive. Nothing has worked. And there is no space on the main harddrive to capture to.
I know there is a lot of speculation about whether FCP would even run on a Mini, but it will. If only I could capture it would be a reat capturing station. Has anyone had success? Its pretty frustrating as I've used the Power PC Mac Mini for capturing in FCP 5.0 without any problems. Why would apple make the new Mini crapier?
Intel mini core duo Mac OS X (10.4.6)

I would recommend you post your topic in the Final Cut Pro forum. However, since the Intel-based Mac mini is not supported, it may simply not work.
-Doug

Mac Mini Superdrive won't feed disk

Similar Messages

Maybe you are looking for