Mac not automatically connecting to Aiport Express

I recently set my airport express basestation with a WEP security password. Now my computer no longer automatically connects when I turn it on, whereas my girlfriends PC does. I have to wait then select my network from the airport drop down list. When I am at work or anywhere else for that matter my computer connects automatically to the network available even though it also is password protected...
Anyone got any ideas...........

I have had wireless problems intermittently for a year, and seriously for 6 weeks. Apple denied the issue and was no help in spite of many tens of thousands of people on their own discussions complaining. I found a post suggesting a couple of things which fixed the problem. I don't know if both are necessary, but the first by itself does not solve the problem.
Lock the channel of your router to channel 1, apparently Apple and 802.11n don't play well together on higher channels. When this becomes a standard this will be resolved I hope.
Open your network preferences, select 'airport' and advanced. Delete unused networks. Select your network.
Open TCP/IP and write down all the settings, configure iPv4 manually. Enter the settings manually. Turn off IpV6.
Open DNS and write down your DNS server. Delete it and re-enter it manually.
This has worked on 2 macbooks and an iMac for the last 3 weeks with no network drops.
Joe Shea
Philadelphia

Similar Messages

PowerBooks will not automatically connect to Airport Express

Recently purchased iPhone and changed my Airport Express password to something easier to spell on iPhone keyboard. Since then, two PowerBooks I own (early G4 and later G4) will not automatically connect to Airport Express Network. I have to manually go to Airport icon in menu bar and join network. Any advice on this small annoyance is greatly appreciated.

Went to the Sys Pref and edited the profile of the AE. Now loads fine.

Mac NOT automatically connecting to preferred wifi network

Hi,
I am facing a problem with OS X 10.9.1 (Mavericks) wifi connection.
I use a Time Capsule as a base station and 13" Macbook Air (2012). The base station is connected to the internet through a PPOE connection.
Here are the details.
Since upgrading to OS X 10.9.1, my Mac automatically connects to preferred wifi network ONLY WHEN the wifi is available at start up or when the Mac wakes up from sleep, but NOT OTHERWISE.
Before the upgrade, the Mac automatically connected to the preferred wifi network not just at start up, but whenever the wifi became available.
In other words, after the upgrade, if I boot up the Time Capsule base station and the Mac simultaneously, the Mac scans for the base station wifi network (this is configured as the top preferred wifi network) at start up, but since the base staion is still booting up, the Mac doesn't find the wifi.
But once the base station has booted up and wifi is available, the Mac no longer bothers to join it. At this point, the Mac is also not able to do Time Machine backups to the Time Capsule because it is not able to locate the Time capsule disk over the wifi.
This situation remains (i.e., the Mac being not connected to the wifi) unless I do ONE of the following:
1. I manually select the preferred wifi network using the wifi icon at the top of the screen; OR
2. I put the Mac to sleep (by closing the cover) and then wake it up. On wake up, it connects automatically to the preferred wifi network; OR
3. I turn of the wifi (using the wifi icon on the top) and turn it back on, at which point, the Mac automatically connects to the preferred wifi network.
I have tried everything possible including contacting Apple support, but so far the issue is unresolved.
Appreciate any help you can provide.
Prem

I have had wireless problems intermittently for a year, and seriously for 6 weeks. Apple denied the issue and was no help in spite of many tens of thousands of people on their own discussions complaining. I found a post suggesting a couple of things which fixed the problem. I don't know if both are necessary, but the first by itself does not solve the problem.
Lock the channel of your router to channel 1, apparently Apple and 802.11n don't play well together on higher channels. When this becomes a standard this will be resolved I hope.
Open your network preferences, select 'airport' and advanced. Delete unused networks. Select your network.
Open TCP/IP and write down all the settings, configure iPv4 manually. Enter the settings manually. Turn off IpV6.
Open DNS and write down your DNS server. Delete it and re-enter it manually.
This has worked on 2 macbooks and an iMac for the last 3 weeks with no network drops.
Joe Shea
Philadelphia

How to connect old aiport express to my new Airport Extreme? My Ipad says "base station e5713b cannot be configured" and my AirPort tool on my PC will not permit me to add my new Airport Extreme network (no network names to choose from)

How to connect old aiport express to my new Airport Extreme?
I have a PC running with Win7 and just replaced my Jensen With a brand New Airport Extreme.
I have set up the Airport Extreme to the internet, Iphones and Ipads and it work as it should.
I have downloaded latest Version of Airport tool on my PC. In addition i have downloaded the airport tool for Ipad.
I have reset one of my airport Express and it now shows up both on the Ipad and on the PC airport tool.
My Ipad says "base station e5713b cannot be configured."
I have wired the airport Express to my Ethernet to be able to "see it" on my Airport tool.
My AirPort tool on the PC will not permit me to add the airport Express to my new Airport Extreme network (no network names on the drop-down list to choose from). I wished for an easy set-up, but nothing seems to be plug and play as the Commercial says.. can you please help me?
Sigve

Hi
Thanks for Swift reply.
Yep - I in fact have two A1088 and one A1264
I actually bought the new router because the Jensen
router always lost connection to the Airport Express after some hours or days. I
always needed to restart my Jensen to play music and that was driving my wife
mad. The hope was that the Extreme should fix this. Both A1088 have been set up
to only stream music to two of my stereo amplifiers from my PC’s Itunes library.
Are the A1088 now useless?
The A1264 has been set up to feed internet into a Denon Reciever that needed Ethernet cable.
Please advise
Regards
Sigve

My Mac will not automatically connect to a web site when I double click

My Mac will not automatically connect to a web site when I double click. The Icon blinks but nothing happens. This happened once before but I don't recall how it was fixed. I can often (but not always) open the site by using "open with Safari.app(default)

Firefox 3 will not run on OS X 10.3.9, it requires at least 10.4
Try one of these browsers to see if you can access Hotmail - [http://www.seamonkey-project.org/releases/seamonkey1.1.19/ SeaMonkey 1.1.19] or [http://caminobrowser.org/download/ Camino 1.6.11]

Iphone 4 does not automatically connect to Airport WIFI from i Mac if it does it will not connect to Safari

iPhone 4 does not automatically connect to my iMac's Airport network. When I do get connection Safari will not open on iPhone?

Have you tried BT's Support Communities? http://community.bt.com/t5/BB-Speed-Connection-Issues/unable-to-connect-iphone-t o-BTHomeHub-Wi-Fi/td-p/1816

Wifi does not automatically connect on iMac

When turning on my imac intermittantly the wifi internet connection does not automatically connect and when this happens i have trouble manually connecting it, resulting in me turning airport wifi on and off upto 5 times.
I am running OSX Lion V 10.7.4.
Any sugestions?

Hi, this has worked for a few...
Make a New Location, Using network locations in Mac OS X ...
http://support.apple.com/kb/HT2712
old... http://docs.info.apple.com/article.html?artnum=106653
Make a New Location, Using network locations in Mac OS X ...
http://support.apple.com/kb/HT2712
10.7…
System Preferences>Network, top of window>Locations>Edit Locations, little plus icon, give it a name.
10.5.x/10.6.x/10.7.x instructions...
System Preferences>Network, click on the little gear at the bottom next to the + & - icons, (unlock lock first if locked), choose Set Service Order.
The interface that connects to the Internet should be dragged to the top of the list.
Instead of joining your Network from the list, click the WiFi icon at the top, and click join other network. Fill in everything as needed.
For 10.5/10.6, System Preferences>Network, unlock the lock if need be, highlight the Interface you use to connect to Internet, click on the advanced button, click on the DNS tab, click on the little plus icon, then add these numbers...
208.67.222.222
208.67.220.220
Click OK.
Also, turn off IPv6:
System Preferences » Network » AirPort » TCP/IP tab » Configure IPv6
Or whatever Interface you use.

Does not automatically connect to wireless network anymore

Mac Book does not automatically connect to know networks any longer.

Hi sashton,
When troubleshooting Wi-Fi connectivity issues, I find the following resource has the most relevant information:
Troubleshooting Wi-Fi issues in OS X Lion and Mac OS X v10.6
http://support.apple.com/kb/HT4628
Furthermore, you may want to avoid giving your network a common name. While the following article (and excerpt) refer to iOS devices, the same applies for your Mac:
Avoid giving your wireless network a common name (SSID)
http://support.apple.com/kb/HT4450
If you were to give your wireless network a common name (SSID), users of your network who use iOS devices [sic] and are away from your network would run the risk of joining a different network with the same name. Having joined the unexpected network, they would be exposed to potential data theft.
Because of this security issue, Apple maintains a list of common or ambiguous SSIDs, including the default SSID for many commercially available access points, as well as the SSIDs "wireless" and "default". If your network's name is on the list, any iOS device [sic] that joins the network stores the access point's BSSID and associates it with the network's SSID. Subsequently, it will only auto-join the network if the access point's BSSID matches the information the device has stored. This avoids joining a different network with the same name.
Therefore, you may want to refer to the following article when configuring your Wi-Fi router:
iOS and OS X: Recommended settings for Wi-Fi routers and access points
http://support.apple.com/kb/HT4199
Thanks,
Matt M.

Airport Extreme Card (will not automatically connect to home network)

Running OSX (10.4.7) on a G5 2.0 DualCore. I just had an Airport Extreme Card installed by Apple a week ago. Everything was working fine with WiFi ( I use a Lynksys Router. But oddly now when I cold boot up, the Airport Extreme will not automatically connect to my home network. The little Airport icon on the upper right is always greyed out ( even though clicking on the icon... says that Airport is "On" ). So I now have to manually select my home network everytime I boot up. The first week or so though, I didn't have to do this...it just automtically connected to my home network. I made no changes to the router settings, nor the Network prefs.

I have been able to get my home network running with simultaneous access to the internet with the MacMini and the PB G4 via a WL router (Netgear WGR614v4 with four ethernet ports).
This was the process:
1a) Turned off airport on both computers.
1b) Turned off both compters and
1c) disconnected the router from the cable modem.
a) Disconnected ethernet cable from WL router to Macmini.
2b) Powered down the router for 10 seconds.
3a) Keeping both computers unpowered,repowered router and pressed the reset button (behind an unmarked tiny hole in the back of the router) then re-connected it to cable modem. Waited 30 - 40 seconds until internet service lights flickered green.
3b) Reconnected ethernet cable to MacMini and turned on power for MacMini. No Airport running. With administrator privilege I configured in Syst. Prefs. "Sharing" folder Internet access using "Built in Ethernet" port for computers running "Airport".
4) Turned Airport network on in MacMini and started browser.
Result: Internet connection established.
5a) Powered up PB G4 and then turned Airport on.
5b) In Syst. Prefs. in "Sharing" folder turned Internet Sharing off. But set "Share your connection from Airport" to computers using: Airport with check-mark. (No Built-in Ethernet and no Built-in FireWire!)
5c)Started browser. Result: Internet connection established.
6a) In the Finder window of both computers I clicked on "Go" in toolbar and looked for the name of the other computer, which were listed as alias besides the "Library" and "Servers" aliases. Clicking on the computer alias brought up the 'Networked Globe' and a control button "Connect".
6b) Clicking on "Connect" brought up the mounted drive of the other computer.
Result: Wireless network operational.
PS: I don't dare yet using encryption for the airport network. That's for another day.
Power Book G4, MacMini Mac OS X (10.4.7)

My iPhone 5 will not automatically connect to my home wifi

My wifes iPhone 5 will not automatically connect to our home wifi, she has to log in each time (she has ios 6.1.4). Mine, however will connect automatically with no issues (we have same phone and ios). Here is what I have done so far to fix the issue and none have worked:
* I have reboted (hold home button and sleep/wake button)
* I have reset the network connections
* I have turned "ask to join" on, connected to the network, turned wifi off and then back on, it did not connect to the wifi
* I have manually connected to the network through the manual option, turned wifi off and then back on, it did not connect to the wifi
* I have erased all content and data and resored the backup from iTunes
* I have restored iPhone from iTunes and restored the backup from iTunes
My phone does not list a "forget this network" as an option on the wifi connection when I pull it up, so this is not an option. So, what else is there to fix the issue?

Hi there Huskerscott!
I have some information here that can help you troubleshoot this issue:
Unable to automatically connect to Wi-Fi
Avoid giving your Wi-Fi network a common name.
Some wireless routers are preconfigured with a common SSID (network name) such as "wireless" or "default."
If your desired Wi-Fi network has a common SSID, try changing the SSID to something unique2.
If your desired Wi-Fi network has a unique SSID, reset network settings by tapping Settings > General > Reset > Reset Network Settings.
Note: This will reset all network settings including: previously connected Wi-Fi networks and passwords, recently used Bluetooth accessories, VPN and APN settings.
Which is taken from this article:
iOS: Troubleshooting Wi-Fi networks and connections
http://support.apple.com/kb/ts1398
It also may be helpful to follow these settings, which are optimal for use with iOS and OS X devices:
iOS and OS X: Recommended settings for Wi-Fi routers and access points
http://support.apple.com/kb/ht4199
Thanks for being a part of the Apple Support Communities!
Regards,
Braden

IPad (3rd generation) does not automatically connect to wi-fi.

iPad (3rd generation) does not automatically connect to wi-fi. It is fully updated to 5.1.1 but you have to manually connect after turning off and back on. I also have an iPad 2 with the same OS but it automatically connects. The wi-fi has no security.

Look at iOS Troubleshooting Wi-Fi networks and connections http://support.apple.com/kb/TS1398
iPad: Issues connecting to Wi-Fi networks http://support.apple.com/kb/ts3304
iOS: Recommended settings for Wi-Fi routers and access points http://support.apple.com/kb/HT4199
Additional things to try.
Try this first. Turn Off your iPad. Then turn Off (disconnect power cord) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
Change the channel on your wireless router. Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
Another thing to try - Go into your router security settings and change from WEP to WPA with AES.
How to Quickly Fix iPad 3 Wi-Fi Reception Problems
http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
If none of the above suggestions work, look at this link.
iPad Wi-Fi Problems: Comprehensive List of Fixes
http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
Fix iPad Wifi Connection and Signal Issues http://www.youtube.com/watch?v=uwWtIG5jUxE
~~~~~~~~~~~~~~~
If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
 Cheers, Tom

PC will not automatically connect to wireless network on startup...

Hi all - I have a WRTG54 wirless router with the latest firmware. Windows XP Home SP2. I have a mixed network with two wired PCs and one wireless. The wireless PC will not automatically connect to the network. To connect to the network i have to go to the wireless network properties box and check "let windows automatically configure network" Once I do this the wirelss PC connects with no problem. Unfortunatley, whenever i turn the PC off and turn it back on the "let windows automatically configure network" is unchecked and i have to go through the process of checking it again. I uninstalled the wireless adapter and reinstalled the drivers only and then ran the windows wireless setup wizard but the problem persists. Any help on this would be much appreciated.!!!! Thanks!!

First of all, give your network a unique SSID. Do not use "linksys". If you are using "linksys" you may be trying to connect to your neighbor's router. Also set "SSID Broadcast" to "enabled". This will help your computer find and lock on to your router's signal.
Do not let "Windows automatically configure your network". Instead do the following:
Also, in the computer, go to your wireless software, and go to "Preferred Networks" (sometimes called "Profiles" ). There are probably a few networks listed. Delete any network named "linksys". Also delete any network that you do not recognize, or that you no longer use. Delete your current network (this will remove any old settings). Reboot computer. Return to "Preferred Networks" and re-enter your current network info (SSID, encryption (if any), and key (if any) ). Then select your current network and make it your default network, and set it to automatic login. You may need to go to "settings" to do this, or you may need to right click on your network and select "Properties" or "settings". Reboot computer. It should connect automatically. If you still have trouble, in the computer, temporarily disable your software firewall, including Windows Firewall, and see if that helps.
Some users have reported improved wireless connections by switching to WPA ( = WPA with TKIP) encryption.

Windows 8.1/IE 11 Does Not Automatically Connect to the Internet

Windows 8.1/IE 11 Does Not Automatically Connect to the Internet
I can't find the dial and redial options anywhere.
I' m connecting through PPPOE but only manual.
I know that in windows 7/8 a program like IE9 or IE10 could connect to the internet, but now it just says that I am not connected to the internet.
How to connect automacally to the internet and how to let IE to connect automatically to the internet, and why I don't have the options for dialing and redialing like in Windows 8?
Thank You

Hi,
Sorry for my dilatory reply, what does your mean that IE dialing to connect to internet? Did your system can connect to Internet? or just IE 11 couldn't connect to internet. you can
check your IE poxy setting in Connections of Internet options.
If you encountered any IE problem, you can try to reset IE for test to resolve this problem.
If you need further assistance on this particular issue or any other Windows related issue, let us know and we will be glad to assist you.
Roger Lu
TechNet Community Support

TS4209 Macbook Air with OS X 10.8.2 not automatically connecting to known wifi network after sleep

Macbook Air with OS X 10.8.2 not automatically connecting to known wifi network after sleep

If you are using WEP as a security on your router that is why it won't connect. WEP is so old school and very insecure that Apple has made it so there WiFi cards won't connect to WEP. It might as well be wide open. You can try that. Take all security, WEP/WPA/WPA2, off your router and see if it connects.
If it does then use either WPA or better WPA2.

Wicd does not automatically connect to eth0

Wicd works fine using my wireless network. It does not automatically connect to eth0 when I plug in a cable, but I can connect to it by pressing connect manually.
I already have ethtool installed (do I need to run ethtool as a daemon???)

stabele wrote:I have two maybe naive question:
1)are you connected to wireless network before you plug in ethernet cable? If yes, than wicd does not automatically switch to wired network. Maybe you can get it done by custom scripts wicd support for each connection, but I never used this thing in wicd.
2) do you have disabled in rc.cong interfaces you want wicd to manage INTERFACES=(!eth0 !wlan0) ?
Thanks for your answers, 1) no I'm not connected to wireless, and 2) eth0 is disabled.
I found out it works fine if I connect eth0 manually and then I can remove and plugin the cable all I want and it automatically connects. This is because dhcpcd is already running for eth0 so maybe I should run dhcpcd eth0 in a boot script (although I think wicd should do this).

Mac not automatically connecting to Aiport Express

Similar Messages

Maybe you are looking for