Mac OS 10.8 Installation Problems

After installation the computer will not boot up and constantly cycles. Did a safe start and lost my Safari application. I have an NVIDIA quadro 4800 Graphics Card installed and I was able to download the latest update in 10.7.4, but 10.8 doesn't allow me to install the update that, bTW, says works with 10.8. Now my Mac Pro doesn't see the graphics card and I can't use FCP or Resolve. Here's the problem log:
Interval Since Last Panic Report: 6359529 sec
Panics Since Last Report: 5
Anonymous UUID: 4CB87D56-DA4B-4815-8FB1-DD0E8BA6EA61
Wed Aug 8 14:45:07 2012
panic(cpu 10 caller 0xffffff80002b7b95): Kernel trap at 0xffffff7f822faffc, type 14=page fault, registers:
CR0: 0x000000008001003b, CR2: 0x000000000000001c, CR3: 0x000000000bf3c025, CR4: 0x00000000000206e0
RAX: 0xffffff8008cb1b04, RBX: 0x0000000000000000, RCX: 0x0000000000000000, RDX: 0x0000000000000000
RSP: 0xffffff81b697b0b0, RBP: 0xffffff81b697b1f0, RSI: 0x0000000000000000, RDI: 0x0000000000000000
R8: 0x0000000000000000, R9: 0xffffff81b697b3c0, R10: 0xffffff7f822faf50, R11: 0x0000000000800000
R12: 0x0000000000000000, R13: 0x0000000000000001, R14: 0xffffff8008cf0204, R15: 0xffffff8008314004
RFL: 0x0000000000010246, RIP: 0xffffff7f822faffc, CS: 0x0000000000000008, SS: 0x0000000000000010
Fault CR2: 0x000000000000001c, Error code: 0x0000000000000000, Fault CPU: 0xa
Backtrace (CPU 10), Frame : Return Address
0xffffff81b697ad50 : 0xffffff800021d5f6
0xffffff81b69
Model: MacPro5,1, BootROM MP51.007F.B03, 8 processors, Quad-Core Intel Xeon, 2.4 GHz, 16 GB, SMC 1.39f11
Graphics: ATI Radeon HD 5770, ATI Radeon HD 5770, PCIe, 1024 MB
Graphics: Display, PCIe
Memory Module: DIMM 1, 4 GB, DDR3 ECC, 1066 MHz, 0x0000, 0x256834470031553742465238432D48392000
Memory Module: DIMM 2, 4 GB, DDR3 ECC, 1066 MHz, 0x0000, 0x256834470031553742465238432D48392000
Memory Module: DIMM 3, 1 GB, DDR3 ECC, 1066 MHz, 0x802C, 0x394A53463132383732415A2D314734473120
Memory Module: DIMM 4, 1 GB, DDR3 ECC, 1066 MHz, 0x802C, 0x394A53463132383732415A2D314734473120
Memory Module: DIMM 5, 4 GB, DDR3 ECC, 1066 MHz, 0x0000, 0x256834470031553742465238432D48392000
Memory Module: DIMM 7, 1 GB, DDR3 ECC, 1066 MHz, 0x802C, 0x394A53463132383732415A2D314734473120
Memory Module: DIMM 8, 1 GB, DDR3 ECC, 1066 MHz, 0x802C, 0x394A53463132383732415A2D314734473120
AirPort: spairport_wireless_card_type_airport_extreme (0x14E4, 0x8E), Broadcom BCM43xx 1.0 (5.106.198.4.20)
Bluetooth: Version 4.0.5f11, 2 service, 18 devices, 0 incoming serial ports
Network Service: Ethernet 2, Ethernet, en1
Serial ATA Device: HL-DT-ST DVD-RW GH61N
Serial ATA Device: WDC WD1001FALS-41Y6A1, 1 TB
USB Device: BRCM2046 Hub, 0x0a5c (Broadcom Corp.), 0x4500, 0x5a100000 / 2
USB Device: Bluetooth USB Host Controller, apple_vendor_id, 0x8215, 0x5a110000 / 3
USB Device: Generic USB Hub, 0x058f (Alcor Micro, Corp.), 0x9254, 0x1d100000 / 2
USB Device: hub_device, apple_vendor_id, 0x911f, 0x1d130000 / 4
USB Device: Keyboard Hub, apple_vendor_id, 0x1006, 0x1d131000 / 7
USB Device: Apple Optical USB Mouse, apple_vendor_id, 0x0304, 0x1d131300 / 9
USB Device: Apple Keyboard, apple_vendor_id, 0x024f, 0x1d131200 / 8
USB Device: Apple Cinema HD Display, apple_vendor_id, 0x921f, 0x1d133000 / 6
USB Device: hub_device, apple_vendor_id, 0x9130, 0x1d140000 / 3
USB Device: Apple Cinema Display, apple_vendor_id, 0x9222, 0x1d142000 / 5
FireWire Device: built-in_hub, 800mbit_speed

That's not an officially supported graphics adapter, so your only recourse is to the vendor. It would probably need an updated driver to work.

Similar Messages

Final Cut Pro 6 on Mac OS Snow Leopard installation problem HELP!!!

After 2 - 3 hours of installing all 10 FCS 2.0 discs and Software Updates, I can't seem to launch Final Cut Pro 6.0.6. I get *"...software maybe damaged or not installed.."* So I removed all of them and only custom-installed Final Cut Pro 6.0.6. It works with no problem!!! Then I custom-installed Soundtrack, Motion, DVD Studio Pro etc..., I can't launch Final Cut Pro 6.0.6. again! What the **** is going on? I get that "damaged" warning and Final Cut Pro icon is replaced by missing application icon.
My Mac Pro also has _Pro Tools 8 LE_ with _003 Mixer Rack connect to USB_. That's it. No other application. You think this is maybe causing the problem?
Anyone having similar problem?

https://discussions.apple.com/docs/DOC-2494
Carbon Copy Cloner is pretty simple to use. If you have any questions, post back or read the documentation. As I said in the user tip, test your clone after you make it to be sure it is bootable and your apps work.

Mac Flash Player 11 installation problems

I installed Flash Player 11.2.202.228 on Mac that has Mac OS 10.6.8 (64-bit). I use Safari. The installation says it was successful. The Adobe Flash Player Help site detects that it was installed but I have no player. I have un-installed, installed numerous times, started up in Safe Mode, re-started the computer, checked my Internet Preferences to allow plug-ins, everything that I could find on this forum but I am having no luck. Please help. I am not an IT type so simple terms will help.

Hello,
What you meant by Adobe Flash Player Help site detects the Flash Player? Could you please, click the following link?
http://helpx.adobe.com/flash-player/kb/find-version-flash-player.html
Can you see the rolling ball? If that's the case, Flash Player is working fine. Do you have issues with a specific site?
Thanks,
Sunil

I can't get any contact info for installation problem- I just bought a Mac Air and my CS5 is asking for a reinstall. Mac Air has no DVD slots. HELP I al VERY FRUSTRATED THAT ADOBE HAS NO WAY TO GET HELP

I can't get any contact info for installation problem- I just bought a Mac Air and my CS5 is asking for a reinstall. Mac Air has no DVD slots. HELP I al VERY FRUSTRATED THAT ADOBE HAS NO WAY TO GET HELP

You are right, Adobe does not support CS5 because it is no longer sold.
Simply download the trial version of CS5 from this Adobe web site and input your serial number.
Adobe - Photoshop : For Macintosh

Wierd Mac Installer problems

Im not sure why but i cant get any .pkg files to install properly. At some point in the installation the UI becomes totally un responsive and i get the spinning beachball of death. This happens for me with various pkg files, namely the iPhone SDK installer and the Onyx installer package?
Does anyone have any ideas?

See my post with this same post date in the topic iLife '09 installation problems; run preflight script error for one possible cause of this behavior.
It also could be that you need to run the "Permissions Repair" option in Disk Utility's First Aid tab to correct some permission on a system file used during the installation procedure; that your drive's file system needs to be repaired with the "Repair Disk" option; or that the drive does not have adequate free space to complete the installation. (As a rule of thumb, try to leave 10 to 15% of the startup volume's capacity free, or at lease 5 GB over & above whatever the installer tells you is needed for the install itself.)
As a general rule, it is a good idea to quit all other applications before doing an installation that uses Apple's Installer.app, & it may be necessary to disconnect non-essential peripherals (everything except the keyboard, mouse, & monitor) & restart before doing so. You should also consider removing any hacks or uninstalling any third party "enhancers" that modify basic system behavior before doing installs, or at least making sure that the latest versions of such things are installed. (Some "enhancers," especially "Application Enhancer" -- a.k.a "APE"-- are installed by other third party products & their developers do not always make that clear, so do not assume one of these things is not on your Mac just because you have not installed it directly.)

Installation problem w/Vista

Boot Camp/Vista installation problem
MacBook 2GHz Intel Core 2 Duo, 2GB RAM, Snow Leopard 10.6.2.
Trying to install Windows Vista Home Premium using Boot Camp.
Started Boot Camp Installer and created 32GB partition. Inserted Vista disk as instructed and clicked on Start Installation.
Black screen appeared looking like this:
1.
2.
Select CD-ROM Boot Type: _
That last underline was flashing, waiting for input.
First off, I don't know what to type in, but . . .
The keyboard appears to be disabled because no keystroke registers, nor Return/Enter. Even pressing caps lock or num lock fails to register a light on those keys.
The only way out is to hold down the power key until shutdown, then restart with Eject key depressed to eject Vista disk.
Any suggestions would be appreciated.

Hi RebelGood,
have a look here http://forums.macrumors.com/showthread.php?t=467704 for instructions/solution.
Basically you have to make yourself a copy of your Vista disc using the files of that disc and a programm called oscdimg.exe plus a burning program.
And it had to be done on a Windows PC or in virtualized Windows (using Parallels/Fusion/VirtualBox) on your Mac.
Regards
Stefan

Is After Effects CS5.5 PowerPC-only? (Installation Problem)

I just installed Adobe Creative Suite 5.5 Production Premium on a new (2012) Mac Mini (Intel Core i7 processor) running OS X Mountain Lion 10.8.2. Most of the apps installed correctly, but After Effects CS5.5 gives me the following error when I try to launch:
You can't open the application "Adobe After Effects CS5.5" because PowerPC applications are no longer supported.
I tried uninstalling and re-installing the app (along with Flash Catalyst, which also fails), but the error remains. What's the deal here? Is it an installation problem, or is After Effects CS5.5 truly incompatible with my new hardware/OS? Any suggestions appreciated.

Okay, answered my own question. I was installing on a Mac Mini, which doesn't have an optical drive, so I was using a remote optical drive to install across my network. Turns out that confused the installer. I ended up copying the install DVD onto a flash drive and installing from that. Problem went away.

++ Debugging ACR Installation Problems ++

If Photoshop CS2/Bridge is not working correctly after you attempt to install ACR (Adobe Camera Raw) 3.1 or higher, here a some hints on how to debug common installation problems.
1. Make sure that "Camera Raw" appears exactly once in Photoshop's "About Plug-in" menu. If it appears zero times, you did not install the plug-in in a correct location. The correct location is shown below. If it appears more than one time, you have multiple copies of the plug-in installed.
The new location for Adobe Camera Raw 3.x and 4.x is:
>Mac: /Library/Application Support/Adobe/Plug-ins/CS2/File Formats/
b Note: that the Library folder refered to above is that found at root level and NOT the User/Library folder.
>Win: \Program Files\Common Files\Adobe\Plug-ins\CS2\File Formats\
2. If "Camera Raw" appears exactly once in the "About Plug-in" menu, then pick that item and make sure the Camera Raw about box shows version 3.1 or higher. If not, you have the wrong version of Camera Raw installed.
3. Run Bridge and pick "Camera Raw Preferences..." from the Bridge(Mac) or Edit(Win) menu. If the command is grayed out, then you don't have Camera Raw installed in the correct place. If the Camera Raw preferences dialog does not have "Version 3.1 or higher" in the title bar, you have the wrong version of Camera Raw installed.
If after you verify that that 1, 2 and 3 are correct, and you are still having problems (e.g. generic raw image icons in lieu of thumbnail previews), then next step is to purge the Adobe Bridge cache for any folders you are having problems with. The command to use is:
"Tools->Cache->Purge Cache for this Folder".

Understood guys. But let me make a few points.
1. Clearly I'm not the only one who had this problem. In fact, I wasn't the first person in this THREAD to have the problem.
2. I'm fairly computer savvy, and have worked with Photoshop for several years.
3. Yes, it does say c: in point 3, but I find it odd that in point 4 it does say Program Files/.... A very strange way to write it. Also, the c: drive is the default installation drive, so it's not idiocy for someone to assume that the file would be located on the same drive as you selected for installation.
4. This is not about technically right or wrong. I never said that the instructions were wrong. I merely was trying to make a suggestion that would help people avoid the same trap I fell into. Was it my mistake? Yes. Would my clarifying suggestion perhaps help others avoid making the mistake I did. I would hope so. Also, as someone else suggested in this thread, Adobe SHOULD have written an installation program for the ACR 3.1 upgrade that did the placing automatically. After all, EVERYONE knew that ACR3.1 would be released shortly after the release for CS2...in fact Mr. Knoll himself was quoted in other forums about when D2X compatibility would actually happen.
5. The purpose of these forums is to be helpful to other users--not to be patronizing or rude. I'm a big Photoshop fan, and a loyal customer. I'm also in the service industry, and I would bet that customer service experts would raise an eyebrow or two about the tone contained in certain messages in this thread, including from an Adobe employee.
Just my two cents. Flame away if you must. But you might want to take a look at what I actually suggested in my last message before lighting up the torch.

Mac os x lion installation give negative times and keep growing?

Why my mac os x lion installation give negative times and keep growing?
Please help me since i've already try to install more then 10 times and wait until -2 hours but the problem still persist.

On the bottom of your MBP should be a serial number. Enter it here and post back the model/year information:
https://selfsolve.apple.com/agreementWarrantyDynamic.do
Do you already have Lion installed or are trying to install it to replace another OSX? If you are replacing, which OSX is currently installed?
Ciao.

Update installation Problems: Code U44M1P7 in Extension Manger 6.0.4 and Illustrator and PS CS6

Hello,
After the installation of several updates I find several errors in the error log:
" Update installation Problems: Code U44M1P7 in Extension Manger 6.0.4 and Illustrator and PS CS6"
I use a Mac Book Pro with Retina and MAC OSX 10.7.5.
What is the problem and how can I solve it?
Best regards
Frank

Follow the instruction given at the following link:
http://helpx.adobe.com/creative-suite/kb/error-u44m1p7-installing-updates-ccm.html

Mac OS X Leopard installation disc after I install Windows Vista

Hi everyone! Do I need to put my Mac OS X Leopard installation disc after I install Windows Vista? I try to run the windows without install Mac-specific driver for windows but it restarted and back to Mac OS. The frustrated thing is I did not bring my Mac OS with me. Anyone has any solution? Or how can i request a installation disk from Apple? Thank you!

Hi everyone! Do I need to put my Mac OS X Leopard installation disc after I install Windows Vista? I try to run the windows without install Mac-specific driver for windows but it restarted and back to Mac OS. The frustrated thing is I did not bring my Mac OS with me. Anyone has any solution? Or how can i request a installation disk from Apple? Thank you!
Yes you will need to install the apple drivers for win vista. When you boot from a cold start, have you tried holding down the option key to choose which OS to boot from? If you have then, you could try going into startup options from the mac side and choose win vista if it appears. That could be risky though, as you mentioned you do not have the mac install disk. If problems arise you may need the mac install disk to undo the changes.

InDesign/Creative Suite Installation Problem

I just installed Adobe Creative Suite 5.5 to a new iMac, using the Adobe chat to assist. Both Photoshop and Illustrator open without any problems. But InDesign will not open. I did use the Mac Migration Assistant progrtam to move everything from my old iMac to a new iMac, which in hindsight I"m not sure I should have done. Any ideas on how I can get this resolved?

never migrate adobe products. they should be properly installed. http://prodesigntools.com/move-adobe-cs5-between-computers-or-windows-to-mac.html
undo everything you can, clean your computer and then properly install your software per http://helpx.adobe.com/creative-suite/kb/cs5-cleaner-tool-installation-problems.html

The latest Adobe Flash Update for Mac OS stalls on installation at 30% download

The latest Adobe Flash Update for Mac OS stalls on installation at 30% download.
How do I delete my old flash from my mac to attempt clean install?
Any other ideas on how to solve this problem?

Please use the offline installer:
http://fpdownload.macromedia.com/pub/flashplayer/latest/help/install_flash_player_osx.dmg

Mac with latest updates: installation window appears, shows message "Retrieving install" for 3 seconds then installation window goes blank. Why?

Mac with latest updates: installation window appears, shows message "Retrieving install" for 3 seconds then installation window goes blank. Why?

Hold down the option key during start up - you will be given the choice of which partition to use (Macintosh HD or Windows). I am having the same problem - Windows 7 seems to have installed but it goes to a blank black screen and there is nothing to do but force a reboot. I too have an i3 iMac... Windows 7 32-bit from original disc.

I have Migration Assistant/Adobe Installer problems

I have just used the Migration Assistant to move to a new Mac, and all the Adobe suite has transferred over, but the Adobe Installer and the Mac is asking me to reinstall the Installer. When I do this, the installation process begins, but then tells me it needs the Installer in place. Chicken/Egg/Egg/Chicken. What do I do now?

You may need to UN-install, run the cleaner, and RE-install
Discussions of RE-installing
-using the cleaner after uninstalling and before reinstalling will usually help
-http://forums.adobe.com/thread/1408331?tstart=0
-http://forums.adobe.com/thread/1398961?tstart=0
-and http://helpx.adobe.com/creative-cloud/help/install-apps.html
-http://helpx.adobe.com/creative-suite/kb/cs5-cleaner-tool-installation-problems.html

Mac OS 10.8 Installation Problems

Similar Messages

Maybe you are looking for