Mac OS 9 is no longer recognized!!

Hello everyone!
This is something that I have never heard of before and have not found a solution on various discussion pages.
I have decided to purchase myself an iMac G5 and pass my Indigo iMac G3 onto my son. I also decided to "renew" the machine by placing all of the original software back on as if new from the store. But, alas, it is not recognizing the hard drive after a CD-ROM boot from the original Software Restore Disc. (It will not boot from my original Mac OS 9.0 disc.)
Any suggestions wold be greatly appreciated.
Regards,
Rodger Graham-Wilson.
PS The G3's stats are as follows:
Machine Name: iMac
Machine Model: PowerMac4,1
CPU Type: PowerPC 750 (33.11)
Number Of CPUs: 1
CPU Speed: 500 MHz
L2 Cache (per CPU): 256 KB
Memory: 640 MB
Bus Speed: 100 MHz
Boot ROM Version: 4.1.9f1
Thanks,
RGW

I have resolved this one all by myself. I forgot to check with ye olde Drive Setup. It found that the internal hard drive was unmounted. After mounting, it was easy to restore everything.
Sometimes it just takes me to write something down to realise the solution.

Similar Messages

Ipod no longer recognized by itunes (on MAC)

I am running a Mac 10.6.8 and since my last updates, my ipod is no longer recognized in itunes? Is there any conflictual extensions? PLEASE HELP? What do i have to do?? Thanks

iOS: Device not recognized in iTunes for Mac OS X
Do not omit the additional information pararaph.

HT1338 cinema Display 30" no longer recognized by my mac pro? What can I do? It worked fine until now.

Cinema display 30" no longer recognized by my mac pro. Until now it worked without problems, then after a crash it fails to recognize the display.
Now it runs in a far lower resolution. What can I do?
I tried to get da driver for it, but could not find any.

Try the other DVI port on the graphics card. On early Mac Pros, only one port is the dual-link DVI needed for full resolution on the 30" display. Make sure the display's USB cable is plugged into the computer.

LaCie firewire HD no longer recognized by my mac

I have a LaCie external hard drive that has worked flawlessly since I introduced them to one another.
I recently installed BootCamp to install Windows XP on a partition of my mac but when I came back to the Macintosh HD, the Mac no longer recognized my firewire drive as a valid disk.
The message says:
"Disk Insertion
The disk you inserted was not readable by this computer."
Then it asks me to "Initialize..." "Ignore" or "Eject"
Since this drive has a lot of very important files on it (films that I have done), I do not want to end up erasing any of the data.
I tried what the apple site said and I connected it with a different firewire cable, but I still get the same message. I turned off the mac and reconnected it to no avail.
I was wondering if 1)Maybe the firmware update I installed to use BootCamp created a problem for the Firewire port, 2) maybe there is a driver issue that came about after installing BootCamp.
Is there a way to restore my iMac to before I installed BootCamp or the FirmWare update?
Is there an easy answer?
I just need to get my external firewire hard drive working like old times without erasing anything.
I appreciate any help.

Okay, I figured out how to run Disk Utility from the OS X CD.
It still doesn't give me the option to mount it:
Does that mean it is not a problem with the firmware update? Both of my external HDs are giving me this message too.
imac (intel) Mac OS X (10.4.6)

My 2008 Mac Pro is no longer recognizing memory in the B card. Is it simply a defective card or should I look elsewhere for an answer.

My 2008 Mac Pro is no longer recognizing memory in the B card. Is it simply a defective card or should I look elsewhere for an answer? It was working unntil sometime early this year. Thank you for any enlightenment you can provide.

I'm not sure I understand. You swapped the A and B modules. The B module does not show up in the A modules slot? That would indicate the module is bad. If the A module doesn't show up in the B module's slot, then the slot is bad.

Optical Drive No Longer Recognized-- Yosemite, Mac

Like a fool, I updated to Yosemite. Now my external optical drive is no longer recognized and I can't burn a CD in iTunes. Please help! How can I get my computer to recognize my optical drive and burn a disc? I have a Mac Air.

Hi,
How is your optical drive connected? It may be a connection problem.
When you go to About this Mac, Overview, System Report, Disc Burning, what does it show?
Does the device show in the Finder window sidebar or in Disk Utility?

Trying to restore my Mac OS after a hard drive failure and my password is no longer recognized, however I can log in by double clicking on the Lion Icon? How can I reset my password

I am trying to restore my Mac OS after a hard drive failure and my password is no longer recognized, however I can log in by double clicking on the Lion Icon? How can I reset my password

First, make sure caps lock is not on.
Another reason why your password might not be recognized is that the keyboard layout (input source) has been switched without your realizing it. At the login screen, you can cycle through the available layouts by pressing the key combinationcommand-space or command-option-space. See this support article.
If the user account is associated with an Apple ID, and you know the Apple ID password, then maybe the Apple ID can be used to reset your user account password.
Otherwise*, boot into Recovery mode. When the OS X Utilities screen appears, select
Utilities ▹ Terminal
from the menu bar. In the window that opens, type this:
res
Press the tab key. The partial command you typed will automatically be completed to this:
resetpassword
Press return. A Reset Password window opens. Close the Terminal window to get it out of the way.
Select your boot volume ("Macintosh HD," unless you gave it a different name) if not already selected.
Select your username from the menu labeled Select the user account if not already selected.
Follow the prompts to reset the password. It's safest to choose a password that includes only the characters a-z, A-Z, and 0-9.
Select
 ▹ Restart
from the menu bar.
You should now be able to log in with the new password, but your Keychain will be reset (empty.) If you've forgotten the Keychain password (which is ordinarily the same as your login password), there's no way to recover it.
*Note: If you've activated FileVault, this procedure doesn't apply. Follow instead these instructions.

Mac Book Pro (Mid 2010) is no longer recognized the external monitor since Lion update.

Mac Book Pro (Mid 2010) is no longer recognized the external monitor sinceLion update. On Mac OSX 10.6, I had no problems.
Mac screen is just blue, as if he switches. But then there is no further signal.
What can I do?

Bump- I have the same issue. Screen slowly dims for no observable reason until I rearrange to point it more directly at light source. Odd thing is that the light in the room does not change. So scren will be fine for hours while I am working and at some point just slowly dim until I rearrange. Any information helpful.

My mac is no longer recognizing my phone and I cannot manage the music on my phone. What can I do?

My mac is no longer recognizing my phone and I can no longer manage my music. How can I change this? I cannot upload IOS 7 because I have too much music on my phone and not enough space, but I cannot delete music on my phone because my computer will not recognize my phone.

Hello Salmomma,
Thank you for the details of the issue you are experiencing when trying to connect your iPhone to your Mac. I recommend following the steps in the tutorial below for an issue like this:
iPhone not appearing in iTunes
http://www.apple.com/support/iphone/assistant/itunes/
Additionally, you can delete music directly from the iPhone by swiping the song:
Delete a song from iPhone: In Songs, swipe the song, then tap Delete.
iPhone User Guide
http://manuals.info.apple.com/MANUALS/1000/MA1658/en_US/iphone_ios6_user_guide.p df
Thank you for using Apple Support Communities.
Best,
Sheila M.

My first generation ipad no longer recognized by itunes 12.1.2.27

I just recently updated iTunes to 12.1.2.27 now my first generation iPad is no longer recognized.
iPad Model MC349FD / Mid 2011 iMac 3.4GHz, 32GB ram, OS X 10.10.3

Hello there, Blueye3355.
The following iPad Troubleshooting Assistant has some good steps to run through, to make sure you've covered all your bases:
Apple - Support - iPad - iTunes Assistant
http://www.apple.com/support/ipad/assistant/itunes/
If following all the steps listed there are additional options on the last step you might want to try or review the "if the issue persists" steps mentioned in the second part of:
iOS: Device not recognized in iTunes for Mac OS X
http://support.apple.com/kb/ts1591
Thanks for reaching out to Apple Support Communities.
Cheers,
Pedro D.

IPod no longer recognized by MacBook Air

Yesterday I purchased a refurbished iPod Photo. It worked fine yesterday - I synced it with iTunes and was able to place 20g of music on it. Today I plugged it in, and it is no longer recognized by my computer, but still charges. I tried resetting both computer and iPod. I reinstalled iTunes. When I forced my iPod in to disk mode, it did not recognize that it was plugged in to my computer - instead of displaying "Do Not Disconnect" it stated "OK to Disconnect". I tried it on two different computers, and had the same issue.

iOS: Device not recognized in iTunes for Mac OS X
Do not omit the additional information pararaph.

I have 3 older ext. hard drives that I've utilized many times. Today while searching for old files, one of the three is no longer recognized by my PowerMac. Any suggestions?

I have 3 older ext. hard drives that I've utilized many times. Today while searching for old files, one of the three is no longer recognized by my PowerMac. The drive is not listed in Disk Utility. Any suggestions?

Is the computer in you equipment line:
Dual Core Intel Xenon
(which is not a PowerMac but a Mac Pro) the one you are asking about, or do you have an older PowerMac?
If a Mac Pro, their forums are here:
Mac Pro
and, as Mac Pros have a totally different architecture from the pre-2005 Macs this forum covers, you may not have the same issues that can affect the older models. If someone didn't notice your equipment line, you could get advice that doesn't apply.
If you really have a pre-2005 PowerMac, read on.
If the stubborn external is USB and does not have its own power brick (i.e., it gets power only from the computer's UBS ports--"bus powered"), it may not be getting enough power. As electric motors age, they can demand more power than when new, and the power available on any USB port is limited.
The typical workabouts to making a computer recognize an aging, bus-powered USB drive are:
Get a powered USB hub (has its own power brick
Get a "Y" USB cable: 1 Meter USB 2.0 A to 5 Pin Mini B Cable - Auxiliary USB "Y" Power Design for external hard drives.
The second gets power from two USB ports on the computer and often that's enough.
Remember that the USB ports on your keyboard seldom provide enough power even for a thumb drive, so be sure to use the USB ports on the back of the computer.

Canon SX260HS no longer recognized by iPhoto

After upgrading to Mavericks my Canon SX260HS is no longer recognized by iPhoto. When plugged in to a USB port the system report shows the camera, but iPhoto does not mount the camera. The camera briefly displays "communication error" on its display. The SD card can be read by using a standalone card reader attached to another USB port. Looks like some change to the camera communications in Mavericks is at fault, but other than using a card reader I see no solution. Help?

tulsamini:
Wow. You've answered nearly all the questions I was going to ask. What version QT are you running?
Try logging into another account on your Mac and see if the camera can be recognized there. If it is then there's an issue with your primary account. Also try booting into Safe Mode and again check to see if the camera can be seen in your primary account.
Booting into Safe Mode runs the File System Check (fsck) during the boot and only loads the basic minimum extensions, etc. needed by the system. See What is Safe Boot, Safe Mode? (Mac OS X). Again this will see if there's something that you've added that is causing the problem.
A workaround until you find a solution is to use a card reader. IMO, it's the best way to upload from a camera.
Do you Twango?
TIP: For insurance against the iPhoto database corruption that many users have experienced I recommend making a backup copy of the Library6.iPhoto database file and keep it current. If problems crop up where iPhoto suddenly can't see any photos or thinks there are no photos in the library, replacing the working Library6.iPhoto file with the backup will often get the library back. By keeping it current I mean backup after each import and/or any serious editing or work on books, slideshows, calendars, cards, etc. That insures that if a problem pops up and you do need to replace the database file, you'll retain all those efforts. It doesn't take long to make the backup and it's good insurance.

Firewire external mobil disk hard drive is no longer recognized

After last system update, my firewire external mobil disk hard drive is no longer recognized. Any solutions?
Why does MacOS go backwards... gets worse over time?

Thought you could use this info about getting FireWire to work! I have had no trouble with any update Apple puts out (the Combo update is what I normally choose). Are you running 9.2 like your specs. say? You are in the Tiger forum, so I'll assume you haven't updated your Macs specs.
First, you should always Repair Permissions in Disk Utility before and after any update; I would do that now. If you installed your update with FireWire plugged in, your Mac may not recognize it anymore.
Try resetting your FireWire ports by disconnecting all FW devices, shut down your Mac and unplug it from AC power (wall socket) for 30 minutes. plug it back in and try FW.
If that did'nt work, download the combo update from this site (yours may be corrupt), not Software Update, disconnect all firewire + USB devices except keyboard + mouse, Repair Permissions, re-install update, Repair Permissions again + try. Yours may be the 10.4.5 Combo update. Others reading, download the Combo that applies to your system.
If that still did'nt get it Zap the PRAM. While restarting Mac hold down the following key combo Command-Option-P-R. Keep holding those keys down till you hear the second start-up chime, then release.
For those of you with Macs that are not PowerBooks or iBooks, a bad internal battery can cause FireWire to not be recognized, so make sure it's good!
Good Luck!
Cheers!
DALE

Since installing Leopard, my iPhone is no longer recognized by iMac

Since installing Leopard, my iPhone is no longer recognized by iTunes and cannot synch. Could you let me know how I can get iTunes to recognize my iPhone again. It is odd since i plug the iPhone into the iMac and it is no longer recognized in iTunes and my address book and calendar. It worked fine before installing Leopard. You assistance is greatly appreciated.

Joseph Pascal wrote:
Thanks Jason. How do I run the software updated?
Click the Apple(top left corner of the screen)> Software Update.
http://docs.info.apple.com/article.html?path=Mac/10.5/en/11410.html

Mac OS 9 is no longer recognized!!

Similar Messages

Maybe you are looking for