Mac OS X 10.4. 11 Disk Utility - Cannot find Brand New HardDrive

I've recently swapped Computers with my sister, and I felt a little "upgrading" was in need of the PowerMac. I went and got a brand new HD, and Ram. When I went and changed everything around, I got to the disk Utility and now it wont even pull up my HD. - Long story shot

From your computer info posted and the fact that you're planning on installing OS 10.4.11, I assume that you have a Blue & White G3. If so, there is a potential problem, if you've connected a large capacity drive to the onboard IDE controller in a B&W G3 having the first revision motherboard. Drives larger than 30-40 GBs can have stability issues, so that a Mac-compatible ATA controller PCI card must be used, such as the (now-discontinued) Acard AEC-6280M. Although a separate issue, an ATA-133 controller card also takes care of the 128 GB limit mentioned by Grant in his post, by recognizing the entire capacity of large drives. If you have a Blue & White G3, post back for a link to an article that can be helpful in determining whether you have the first or second revision motherboard. Incidentally, the dedicated Forum for the Power Mac G3s can be found here.

Similar Messages

Airport utility cannot find my new Airport extreme.

I plugged in the airport, opened airport utility and it scans and says it finds nothing. The airport is right next to my computer. It is not out of range. It is blinking orange. I have a dell inspiron 600m running windows XP. My modem is a westell 6100g. I anticipate problems getting them to work together, but i didn't expect to not be able to even find the airport to configure it. What is going on here? Please help.

So I successfully set up the airport, disconnected it from the computer, connected it to the modem and used the laptop wirelessly, went downstairs to see if the other computer (a mac) could get online, it could. Left the house, came back around midnight. No wireless signal. went to sleep. this morning, no wireless signal. opened airport utility. No airport found. Reconnected laptop to LAN. Found. went through setup again. got wireless signal. disconnected laptop. went in other room. 5 minutes later, no signal, no ability to see airport. connected laptop to modem and put it in bridge mode. same situation, only the signal seems to dissapear quicker. I can access the internet by connecting my laptop to the airport LAN, and while that cable is connected I can see (and my computer says, use) the wireless network, but as soon as i disconnect the computer the wireless goes down.
Bob- my windows firewall is completely disabled and i currently have no anti-virus software installed, so i don't think that is the problem.
Any advice?

Airport utility cannot find my new Time Capsule

I just bought a new timecapsule, connected it to my modem via the wan port, turned it on and the light went from green to flashing amber. Airport Utility does not find any wireless devices i can try over and over but no succes.
I reset the Timecapsule a few times already. Whatever i try airport utility does not find anyhting and i can make no connection with my timecapsule
I thought this should be so hard.. does anyone know whats going wrong?
I looked on various websites but i never get past the second 2 step: Airport utility recognizing my timecapsule
Also tried software update but it says everything is up to date..
Hope somebody can solve this!
Thanks in advance
Rhodo

Airport Utility does not find any wireless devices i can try over and over but no succes.
Look for another wireless network with a name like Apple Network xxxxxx and log on to this network. No password is required. Then open AirPort Utility.
Or, temporarily connect an Ethernet cable from your computer to one of the LAN <-> ports on the Time Capsule and then open AirPort Utility.

I just restarted my mac then suddenly when it boots,disk utility came and says different option like repair disk, get help, reinstall OSX and I tried to click disk repair but it says that I am um able to repair the disk

i just restarted my mac then suddenly when it boots,disk utility came and says different option like repair disk, get help, reinstall OSX and I tried to click disk repair but it says that I am um able to repair the disk

It sounds like your hard drive either has a software problem that Disk Utility cannot fix or that the HD has failed (mechanically).
Your Mac may have booted either to your recovery partition or to internet recovery in an attempt to repair the drive- I can't tell from your post.
I'll assume that it was the recovery partition.
Try to boot into internet recovery (hold down option command R at restart), and see if you can repair your HD with Disk Utility. You should also repair permissions while you're there.
If that doesn't work, try to boot into single user mode (restart, hold down ⌘S until you see a black screen with white text) and repair your hard drive. Here's a reference with directions: Repair Your Hard Disk in Single User Mode | Everything Macintosh
If that doesn't work you have a few options:
If your mac originally came with installation disks, you can try to boot from the installation disk and then see if you can repair the HD.
There is a small chance that Techtool Pro 7 will be able to repair your HD if Disk Utility can't.
If none of that works then your HD has probably failed and will need to be replaced, which is not too difficult to do yourself if you can use a screwdriver.

Have a mac book pro that crashed. ran disk utility to repair. comp booted and ran for short time. then crashed. ran repair again. disk utility said it could not repair files and i needed to format hard drive and start again. now nothing works

have a mac book pro that crashed. ran disk utility to repair. comp booted and ran for short time. then crashed. ran repair again. disk utility said it could not repair disk and needed to format and start again.
comp said it could not unmount disk and now when comp trys to boot all i get is a question mark on the screen. help

Erase and Install
1. Boot from your Snow Leopard Installer Disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu.
2. After DU loads select your hard drive (this is the entry with the mfgr.'s ID and size) from the left side list. Note the SMART status of the drive in DU's status area. If it does not say "Verified" then the drive is failing or has failed and will need replacing. SMART info will not be reported on external drives. Otherwise, click on the Partition tab in the DU main window.
3. Under the Volume Scheme heading set the number of partitions from the drop down menu to one. Click on the Options button, set the partition scheme to GUID then click on the OK button. Set the format type to Mac OS Extended (Journaled.) Click on the Partition button and wait until the process has completed.
4. Quit DU after formatting completes and return to the installer. Install Snow Leopard.
5. After restart into Snow Leopard download and install Mac OS X 10.6.8 Update Combo v1.1.

TS2570 Question re: "Start from your Mac OS X Install disc; use Disk Utility"

I've worked my way through the step-by-step trouble shooting in the TS2570 article up to "Start from your Mac OS X Install disc; use Disk Utility". So far, every step results in the same outcome - my formerly trusty 2007 Intel duo core iMac (24") will not start up, freezing on a grey screen with a blinking question mark on a folder. I don't completely understand this next step. I have both a Leopard and a Snow Leopard disc. I'm not positive whether these were for the iMac, or my old Macbook Pro. I assume this makes a difference.

Question (?) Mark, Blinking Folder, or Gray Screen at Startup
These are related but not identical issues. Their causes are outlined in Intel-based Mac- Startup sequence and error codes, symbols. Solutions may be found in:
A flashing question mark appears when you start your Mac
A flashing question mark or globe appears when you start your Mac
Mac OS X- Gray screen appears during startup
In most cases the problems may be caused by one or more of these:
a. Problem with the computer's PRAM - See Resetting your Mac's PRAM and NVRAM.
b. Boot drive's directory has been corrupted - Repair with Disk Utility.
c. Critical system files are damaged or deleted - Reinstall OS X.
d. The disk drive is physically non-functional - Replace the hard drive.
Note that the information I have provided is what Apple recommends, If other users suggest different solutions than found here, then be sure what they recommend does not impact on your warranty, if any, or ability to get continuing Apple service.
Please don't start removing drives or changing cables unless you know what you are doing and have exhausted other non-invasive alternatives outlined here. If you perform any work yourself that is unapproved by Apple, then you will void any warranty you may have and lose all further Apple Support.
Repair the Hard Drive and Permissions
Boot from your Snow Leopard Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer.
If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
The main difference if you are using Lion or Mountain Lion is that you must first boot from the Recovery HD. Simply boot from the Recovery HD to perform the above.
Reinstall Snow Leopard Without Erasing The drive
1. Repair the Hard Drive and Permissions
Boot from your Snow Leopard Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer.
If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
2. Reinstall Snow Leopard
If the drive is OK then quit DU and return to the installer. Proceed with reinstalling OS X. Note that the Snow Leopard installer will not erase your drive or disturb your files. After installing a fresh copy of OS X the installer will move your Home folder, third-party applications, support items, and network preferences into the newly installed system.
Download and install Mac OS X 10.6.8 Update Combo v1.1.
Reinstalling Lion/Mountain Lion Without Erasing The Drive
Boot to the Recovery HD: Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
Repair the Hard Drive and Permissions: Upon startup select Disk Utility from the main menu. Repair the Hard Drive and Permissions as follows.
When the recovery menu appears select Disk Utility. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the main menu.
Reinstall Lion/Mountain Lion: Select Reinstall Lion/Mountain Lion and click on the Continue button.
Note: You will need an active Internet connection. I suggest using Ethernet if possible because it is three times faster than wireless.

Brand new Mac, had to erase drive through disk utility as time machine back up failed. Now disk utility only has the option to install Mountain Lion which my Mac won't allow. Anyone any ideas as my Mac won't load anything up but disc utility!

Brand new Mac, had to erase drive through disk utility as time machine back up failed on initial setup, USB cable popped out Now can only access disk utility as won't load to log in screen. The only has the option in disc utility is to re-install Mountain Lion which my Mac won't allow or loading another time machine back up but after an hour of it processing, that didn't resolve the issue either! The time machine back up is the latest back up of my Mac Book Pro which was using OS X Maverix. I'm guessing I'm going to have to take my Mac to the store but that would be a hassle so does anyone have any ideas?

Follow this guide using another Mac.
Insert your newly created Mavericks USB into you Mac, press the power button and then hold down 'option,' until it gives you an option to boot from the USB. You will then be able to erase the internal disk with Disk Utility and reinstall Mavericks straight after.
After that you should be able to use Migration Assistant to restore your applications and user data.

After Server Administration Software for 10.6.8 install on my mac- Now I can't use Disk Utility ?

I installed ServerAdministrationSoftware for 10.6.8 on my mac- NOW I can't use Disk Utility - get Dyld Error Message: Library not loaded: /System/Library/PrivateFrameworks/PlatformHardwareManagement.framework/Versions /A/PlatformHardwareManagement? Also, the only reason I installed this was for the Workgroup Monitor which kicks out the same error.
Any help would be appreciated!

FireFox can't open lots of files it isn't suposed to. DMG is opened by the Mac osx as a virtual volume file you just drag the FireFox icon to where you want it installed. Check your desktop for a FireFox volume... like a drive. Double click the DMG file if it is not there. This is how Mac works it has nothing to do with FireFox, many apps install this way!

I tried partitioning my HD to install linux, the installion was not successful and now I can't boot my mac, I tried internet recovery, it was not helpfull as the disk utility cannot delete the partition I created.

I tried partitioning my HD to install linux, the installion was not successful and now I can't boot my mac, I tried internet recovery, it was not helpfull as the disk utility cannot delete the partition I created. It was only showing me an error message "EFI files are missing", I realized that it is trying to boot from the new partition I created for the installation of the linux I intended to do.

It sounds like you may have multiple problems, but none of them are likely to be caused by malware.
First, the internet-related issues may be related to adware or a network compromise. I tend to lean more towards the latter, based on your description of the problem. See:
http://www.adwaremedic.com/kb/baddns.php
http://www.adwaremedic.com/kb/hackedrouter.php
If investigation shows that this is not a network-specific issue, then it's probably adware. See my Adware Removal Guide for help finding and removing it. Note that you mention AdBlock as if it should have prevented this, but it's important to understand that ad blockers do not protect you against adware in any way. Neither would any kind of anti-virus software, which often doesn't detect adware.
As for the other issues, it sounds like you've got some serious corruption. I would be inclined to say it sounds like a failing drive, except it sounds like you just got it replaced. How did you get all your files back after the new drive was installed?
(Fair disclosure: I may receive compensation from links to my sites, TheSafeMac.com and AdwareMedic.com, in the form of buttons allowing for donations. Donations are not required to use my site or software.)

External hard drive not visible in disk utility or finder

Hi all,
I have had a good look through previous discussions and I can't seem to find an issue relevant to mine.
My external hard drive has 2 partitions (1 time machine back up, 1 general hard drive). The issue is that the HD is running when it is plugged in however it is not visible in either disk utility or finder.
I am running OS X 10.10 (Yosemite) on a 2010 MacBook Pro. I also have parallels desktop running windows 7. When I boot windows and plug in the HD I usually get the option to mount the HD to either OS X or Windows. With this issue the option window appears for a split second (not enough time to select either) and then disappears. It seems that the HD may be ejecting itself as soon as it is registered by the computer. I have tried using a different power cable for the HD and also a different usb cable, this doesn't help.
The external HD is a Samsung D3 Station, which i have had for 6 months now and never had an issue with.
Any help is appreciated
Thanks,
Bruce

An update for anyone who can help me:
I have tried the external hard drive in other computers (mac and windows), each time I get the same problem above.
I have removed the HD from the enclosure and purchased a docking station for it (3.5" SATA). When I plug it in to the laptop it disconnects itself straight away before it is visible. With the windows computers it installs the drivers and says that the device is ready to use, then disconnects before it shows up.
As the HD is not visible there is no option to re-format or anything.
This is very frustrating as I was using the HD with no issues and it randomly disconnected and I have not been able to access since.
Thanks in advance for any help.
Bruce

Disk Utility Cannot Be Opened Because Of A Problem

When trying to launch Disk Utility I get the following error message. Does anyone have any suggestions on how to fix this? I'm running 10.6.4. Thanks in advance for any help.
Disk Utility cannot be opened because of a problem.
Check with the developer to make sure Disk Utility works with this version of Mac OS X. You may need to reinstall the application. Be sure to install any available updates for the application and Mac OS X.
Process: Disk Utility [342]
Path: /Applications/Utilities/Disk Utility.app/Contents/MacOS/Disk Utility
Identifier: com.apple.DiskUtility
Version: ??? (???)
Build Info: DiskUtility-2980100~37
Code Type: X86-64 (Native)
Parent Process: launchd [131]
Date/Time: 2010-08-21 18:44:20.863 -0400
OS Version: Mac OS X 10.6.4 (10F569)
Report Version: 6
Interval Since Last Report: 2359004 sec
Crashes Since Last Report: 75
Per-App Crashes Since Last Report: 5
Anonymous UUID: 93489452-CA67-4296-AA9A-2228E825BA2F
Exception Type: EXC_BREAKPOINT (SIGTRAP)
Exception Codes: 0x0000000000000002, 0x0000000000000000
Crashed Thread: 0
Dyld Error Message:
Library not loaded: /System/Library/PrivateFrameworks/PlatformHardwareManagement.framework/Versions /A/PlatformHardwareManagement
Referenced from: /System/Library/PrivateFrameworks/ServerFoundation.framework/Versions/A/ServerF oundation
Reason: no suitable image found. Did find:
/System/Library/PrivateFrameworks/PlatformHardwareManagement.framework/Versions /A/PlatformHardwareManagement: no matching architecture in universal wrapper
Model: iMac8,1, BootROM IM81.00C1.B00, 2 processors, Intel Core 2 Duo, 2.66 GHz, 4 GB, SMC 1.29f1
Graphics: ATI Radeon HD 2600 Pro, ATI Radeon HD 2600 Pro, PCIe, 256 MB
Memory Module: global_name
AirPort: spairportwireless_card_type_airportextreme (0x14E4, 0x8C), Broadcom BCM43xx 1.0 (5.10.91.27)
Bluetooth: Version 2.3.3f8, 2 service, 19 devices, 1 incoming serial ports
Network Service: Ethernet, Ethernet, en0
Serial ATA Device: ST3320820AS_Q, 298.09 GB
Parallel ATA Device: OPTIARC DVD RW AD-5630A
USB Device: Built-in iSight, 0x05ac (Apple Inc.), 0x8502, 0xfd400000
USB Device: Keyboard Hub, 0x05ac (Apple Inc.), 0x1006, 0xfa200000
USB Device: Apple Optical USB Mouse, 0x05ac (Apple Inc.), 0x0304, 0xfa230000
USB Device: Apple Keyboard, 0x05ac (Apple Inc.), 0x0220, 0xfa220000
USB Device: IR Receiver, 0x05ac (Apple Inc.), 0x8242, 0x5d100000
USB Device: BRCM2046 Hub, 0x0a5c (Broadcom Corp.), 0x4500, 0x1a100000
USB Device: Bluetooth USB Host Controller, 0x05ac (Apple Inc.), 0x820f, 0x1a110000
FireWire Device: unknown_device, Unknown

Reinstall Disk Utility from your Snow Leopard DVD. If your DVD does not install 10.6.4 then use the Combo Updater to update back to 10.6.4.
How to Use Pacifist to Replace Deleted or Missing OS X Components
Insert the OS X Installer DVD into the optical drive. Use a simple utility like TinkerTool to toggle invisibility so you can see invisible items. Alternatively, open the Terminal application in your Utilities folder and at the prompt enter the following:
defaults write com.apple.finder AppleShowAllFiles Yes
Press RETURN.
To turn off the display of invisible files repeat the above command substituting No for Yes.
The install packages are located in the /System/Installation/ folder on the DVD.
Download the shareware utility Pacifist from VersionTracker or MacUpdate. Use it to extract a fresh copy of the missing item(s) from the file archives on your OS X installation DVD. The file archives are in the /System/Installations/ folder (use Go to Folder option in the Go menu of the Finder.)
Here are Four Basic ways to use Pacifist (courtesy of George Orville.)
A. Drag a .pkg icon onto the Pacifist window .....proceed to step 7.
B. Click on “Open Package ....” and navigate to package desired and click “Open” in the open/save window.....proceed to step 7.
C. Insert Mac OS X installer CD and when it mounts, navigate to .... Menu->Go->Go to Folder.
In the path field enter or paste ....
/Volumes/disc name/System/Installation/Packages (where disc name is the name of the CD/DVD that you inserted.
• Click on the "Go" button .....
• Drag a .pkg to Pacifist..... proceed to step 7.
The package you'll need will have to be discovered by trial and error, but for most applications you should start with the Essentials.pkg and/or Additional Essentials.pkg.
D. Insert your Mac OS X install disk 1 .... and open Pacifist.
1. In Pacifist, select "Open Mac OS X Install Packages" ... dialog may appear asking for disk 2, then disk 3 and finally disk 1 again.... {if DVD is not used)...If “Stop Loading” is selected...the procedure will stop!!!
2a. When loading is complete, a new window appears, click the triangle to display contents of each package...Select item and proceed to step 7.
2b. or click the “Find” icon in the Pacifist window and type the name of the software you need.
3. In the list that comes back, click the top most entry for the item that you want. ..... that is the one for the English language.
4. On the top of the Pacifist window, click “verify” .... you will probably be prompted for your password.
5. Enter checks for.... “verify permissions” and “verify file contents.” and click “verify” ....enter password when prompted.... you will get back output which may look like this:
20 files were scanned.
20 of 20 files were present on the hard disk.
0 of 20 files had file permissions that did not match those specified in the package.
0 of 20 files had checksums that did not match those specified in the package.
6. Click “close”. Go to step 7.
Extract or Install........
7. In the Toolbar (upper left), you now have the option to extract or install. Click a file in the lower list and those two icons will be enabled.
8. If “Extract to...” is selected.... navigate to the location where the file will be placed, select “choose”, select “extract” in new dialog that appears,authenicate , if prompted, click “OK”.
9. In the next dialog, click “Extract”.
10. If “Install” is selected... dialog will appear with the location/path of the installed software. Click “Install”
11. Type in your password, click “OK”
• Pacifist will begin to extract files.
12. In steps 8/10ß.... you also have the choice to “cancel”
Notes.....
• Pacifist may find that a file it is installing already exists on the hard disk. Pacifist will present you with an alert panel....
Stop
Leave original alone
Update ..... Default selection
Replace .... Replace option should only be used on full install packages

Disk Utility can't format new HDD

So I just got a new 4TB drive (WD4003FZEX 4TB 7200 RPM) for my Mac Pro that I'd like to partition... one volume for Time Machine on the boot drive, the other volume for back-up for the two other drives I have in there. I just installed it and initialized the HDD, formatted to Mac OS Extended, but since that finished, I now have two problems:
1.) Disk Utility cannot/will not format the drive (the HDD itself, not the volume). It's not that the Erase option is greyed out or not working, it isn't even there. When I select the disk, it only has two options... First Aid and Partition.
2.) Partition only works partially. I can add a partition, but the Name, Format, and Size fields are all greyed out, so I can't rename the volume or adjust it's size.
What am I missing here?

Never mind. Found this thread, did what it said, and it all works fine now.
https://discussions.apple.com/thread/5039921

My HD needs to be reformatted according to Disk Utility, but even when I use an external device for startup, Disk Utility cannot reformat the HD

I have a Macbook with a 500 GB Hard Drive. A routine check on Disk Utility told me the disk needed to be reformatted. I restarted from an external USB drive, but when I try to use Disk Utility to repair the HD or to reformat it, Disk Utility is unable to do anything with the HD (cannot repair, cannot erase,cannot reformat the HD). Is there a utility App that can help me with this, or is the HD unrecoverable?

Hi
Thanks very much for your reply. We have been starting up from a backup (USB) drive and use the disk utility that is on the backup drive so the internal (problem) HD is not being used for anything (except for wanting to repair it). Still Disk Utility cannot reformat or repair the drive. I have also run Onyx but it tells me everything is OK on the drive.
But I have made a little progress. Using my old install disk for Snow Leopard (10.6.3) I have managed to do a fresh install of the system on the internal HD. Unfortunately, I also asked the install disk to transfer/migrate the settings and documents from the backup drive back onto my internal HD. The install appeared to work, but then it got hung up on copying the documents from my backup drive to the HD. After letting it sit for 2 days without going anywhere, I stopped the install process. I am going to try again, just using my Snow Leopard CD to install Snow Leopard, and nothing else. If that works, I will then get on to the problem of copying the rest of the settings and documents from my backup.
But since the Mac works OK off the USB backup, and will also run off the install CD, I am guessing the problem is with the HD and the only solution might be to replace it if I can't repair it. But the macbook is several years old, and I am not sure it is worth buying a new HD for it.

Disk Utility won't add new partition

I have an external 250GB hard drive connected via USB to my Mac Mini (Early 2009) computer. The drive has a GUID partition table that was created using Windows Vista SP 1. The first partition on the disk is a 128MB Microsoft Reserved partition. The second partition is a 120GB NTFS partition. When I try to use Disk Utility to partition the remaining 112GB of space as a Mac OS Extended Journaled partition I keep getting an error message stating "MediaKit reports no such partition". How do I get around this bug in Apple's Disk Utility application?

techguy378,
As they always do, Microsoft has undoubtedly created "their own" proprietary implementation of the GUID partition table. The effect, in this particular case, is that Disk Utility cannot see that unused space. That doesn't mean this is a Disk Utility "bug."
If one were to do the same thing with Disk Utility- create 2 partitions on a drive that do not fill the drive- that empty space would be included in the partition map. Simple. In your case, however, it appears that Vista has just excluded that empty space from the map entirely. Neat trick, huh?
I think your only solution will be to add a partition in Vista, if that is possible without destroying the current volumes. You can then reformat the new partition in Disk Utility.
Scott

Disk Utility cannot repair startup volume, and where's my AppleCare cover?

Hi all,
The 250GB SATA drive on my Power Mac G5 Dual 2.5GHz has some 'issues' that Disk Utility cannot repair. It says, "Invalid sibling" and something about "key not found" or "keys out of order". I've run fsck -fy in single-user mode but it drops out saying "(4, 18880) error".
I have AppleCare Protection for it until November, but when I log into Apple's site, it says I have no current agreements. I'm at work at the moment and don't have my serial number, so I can't really call them up (and I don't have their phone number to hand...).
Is the hard drive covered under AppleCare?
I don't want to purchase any more software to fix the disk, i.e. Alsoft's DiskWarrior, unless it can be delivered instantly and will work on these problems?
Any help is much appreciated :o)

Thanks for that.
I was willing last night to re-install the OS to see if it was a software problem, but booting into the Tiger install DVD reported the same problems, however it was a little more informative than fsck. It says there are issues on the first two partitions on the boot drive. (I have OS X, Apps and Games partitions on that drive.)
I tried repairing the partitions in different orders, just in case it would help, but it still failed.
If I were to call AppleCare while at work, without the serial number, would they be able to locate my agreement and sort out a repair? APP was bought with the machine and I assumed it would've been registered at that time, but the website says I have no agreements...? Anyone got their phone number?

Mac OS X 10.4. 11 Disk Utility - Cannot find Brand New HardDrive

Similar Messages

Maybe you are looking for