Mac os X 10.6.2 Update v Mac os X 10.6.2 Combined update
Hello -
Dumb question I am sure but what is the difference between the two 10.6.2 updates?
Is one for clients that have 10.6 and the other for clients that have 10.6.1?
Thanks,
Andrew
Hi
Apart from a minor difference in their sizes. Yes.
http://support.apple.com/kb/DL959
http://support.apple.com/kb/DL958
Right hand column. The bit that says "System Requirements". For the Server the Combo Update appears to have two extra 'fixes' not included in the other update. Probably because the previous 10.6.1 update included those extra 'fixes'?
Tony
Similar Messages
-
HT3606 Mac OS X v10.5.8 Combined Update stalls updating my G4 1.25
Mac OS X v10.5.8 Update stalls updating my G4 1.25. A peek at the files being installed was reference to "standalone i386 efi" which has no place on a PPC. Are there different versions of the combined update? There are different sizes of the combined update.
Some general advice on updating Leopard:
It is worth noting that it is an extreme rarity for updates to cause upsets to your system, as they have all been extensively beta-tested, but they may well reveal pre-existing ones, particularly those of which you may have been unaware. If you are actually aware of any glitches, make sure they are fixed before proceeding further.
So before you do anything else:
If you can, make a full backup first to an external hard disk. Ideally you should always have a bootable clone of your system that enables you to revert to the previous pre-update state.
Turn off sleep mode for both screen and hard disk.
Disconnect all peripherals except your keyboard and mouse.
1. Repair Permissions (in Disk Utility)
2. Verify the state of your hard disk using Disk Utility. If any faults are reported, restart from your install disk (holding down the C key), go to Disk Utility, and repair your startup disk. Restart again to get back to your startup disk.
At least you can now be reasonably certain that your system does not contain any obvious faults that might cause an update/upgrade to fail.
3. Download the correct version of the COMBO update from the Apple download site.
The Combo updater of Leopard 10.5.8 can be found here:
http://support.apple.com/downloads/Mac_OS_X_10_5_8_Combo_Update
If you prefer to download updates via Software Update in the Apple menu (which would ensure that the correct version for your Mac was being downloaded), it is not recommended to allow SU to install major (or even minor) updates automatically. Set Software Update to just download the updater without immediately installing it. There is always the possibility that the combined download and install (which can be a lengthy process) might be interrupted by a power outage or your cat walking across the keyboard, and an interrupted install will almost certainly cause havoc. Once it is downloaded, you can install at a time that suits you. You should make a backup copy of the updater on a CD in case you ever need a reinstall.
Full details about the 10.5.8 update here: http://support.apple.com/kb/HT3606
More information on using Software Updater here:
http://support.apple.com/kb/TA24901?viewlocale=en_US
Using the Combo updater ensures that all system files changed since the original 10.5.0 are included, and any that may have been missed out or subsequently damaged will be repaired. The Delta updater, although a temptingly smaller download, only takes you from the previous version to the new one, i.e. for example from 10.5.7 to 10.5.8. Software Update will generally download the Delta updater only. The preferable Combo updater needs to be downloaded from Apple's download site.
Now proceed as follows:
4. Close all applications and turn off energy saving and screensaver.
5. Unplug all peripherals except your keyboard and mouse.
6. Install the update/upgrade. Do not under any circumstances interrupt this procedure. Do not do anything else on your computer while it is installing. Be patient.
7. When it ask for a restart to complete the installation, click restart. This can take longer than normal, there are probably thousands of files to overwrite and place in the correct location. Do nothing while this is going on.
8. Once your Mac is awake, repair permissions again, and you should be good to go!
If your Mac seems slightly sluggish or ‘different’, perform a second restart. It can’t hurt and is sometimes efficacious! In fact a second restart can be recommended.
9. Open a few of your most used applications and check that all is OK. In this connection please remember that not all manufacturers of third party applications and plug-ins, add-ons, haxies etc, will have had time to do any necessary rewrites to their software to make them compliant with the latest version of your operating system. Give them a week or two while you regularly check their websites for updates.
N.B. Do not attempt to install two different updates at the same time as each may have different routines and requirements. Follow the above recommendations for each update in turn.
Lastly, Apple's own article on the subject of Software Update may also be useful reading:
http://docs.info.apple.com/article.html?artnum=106695
[b]If you are updating Safari (or just have):[/b]
Input Managers from third parties can do as much harm as good. They use a security loophole to reach right into your applications' code and change that code as the application starts up. If you have installed an OS update and Safari is crashing, the very [i]first[/i] thing to do is clear out your InputManagers folders (both in your own Library and in the top-level /Library), log out and log back in, and try again.
So, disable all third party add-ons before updating Safari, as they may not have been updated yet for the new version. Add them back one by one. If something goes awry, remove it again and check on the software manufacturer's website for news of an update to match your version of Safari.
Most errors reported here after an update are due to an unrepaired or undetected inherent fault in the system, and/or a third party add-on.
Additional tips on software installation here:
http://docs.info.apple.com/article.html?artnum=106692
To reiterate, Input Managers reach right into an application and alter its code. This puts the behavior of the affected application outside the control and responsibility of its developers: a recipe for problems. That's not to say that issues absolutely will ensue as a result of Input Managers, but you, as a user, must decide. If the functionality of a specific Input Manager or set thereof is really important to you, you may well choose to assume the associated risk.
Again, the advice is to remove all Input Managers from the following directories:
/Library/InputManagers
~/Library/InputManagers
especially prior to system updates (they can always be added back one-by-one later).
Solutions for troubleshooting installation, startup, and login issues in Mac OS X v10.5
http://support.apple.com/kb/TS1541?viewlocale=en_US -
Adobe Photoshop CS2 Error messages after update to mac os 10.4.6
After updated to mac os 10.4.6 everytime I use Photoshop CS2 I receive an error message "Could not complete your request because of a program error"
I did all the workarounds that were described in document 331627 from Adobe's website and nothing worked.
I also subscribe to maxosx.com support and someone suggested removing the legal.localized/Tien...file from the photoshop cs2/legal directory, but everytime I tried to select the directory "legal" from within the finder view, it disappeared and closed the finder window.
HELP!Did you upgrade from a previous version of OS X like 10.3.x or 10.2.x or from a prior version of 10.4.x? If the former, there are probably some files in your previous system folder that need to be restored.
Otherwise, double click Photoshop when it's closed, and then IMMEDIATELY hold Command + Option + Shift. You'll get a box for resetting the settings. Select Yes and maybe that will help.
--Ryan -
Camera Raw 6.7 Update for Mac OS 10.10: Installation Failed error message.
Camera Raw 6.7 Update for Mac: Installation Failed error message. Update downloaded directly from Adobe website. Newly purchased Mac Workbook Pro, OS 10.10, using Photoshop CS5. Other updates successfully accomplished. Camera Raw 6.7 Update was downloaded multiple times with multiple installation attempts. Any recommendations?
thanks for the prompt response...i appreciate it. according to the link you listed, that's correct. the strange thing is that prior to the upgrad to mac os 10.8.4, photoshop CS5 was working just fine and i was able to open my canon raw files with my current camera raw plug-in version 6.7 which adobe has indicated is the last camera raw update they'll be offering for cs 5
so it's clearly an issue related to the "upgrade" of the os. seems like every solution creates 6 new problems...further evidence for the notion that if it ain't broke don't fix it! thanks again. -
After the last update on Mac os 10.9.2 end of April - I
After the last update on Mac os 10.9.2 end of April - I opened Pagemaker and my whole system crashed after talkign with Apple, I had to erase everything on my hard drive. I finally got it fixed and re-installed pagemaker cs5 and a few other program that I HAD to have while I was on vacation. When I got home, I tried installing CC and various programs (pagemaker, indesign, photoshop etc. Had to erase all of the other adobe programs and start from scratch. Every time I open ANY adobe products all of my "white space" is pink and white vertical striped in EVERY program. Apple mail, contacts etc. If I completely shut down the computer and then restart everything is fine until I open an adobe product again. I can't seem to get any help out of Adobe, does any one have any suggestions before I cancel my subscription entirely?
Thank you in advance,
JanieYou may need to ask for help in the individual program forums
This forum is about the Cloud as a delivery process, not about using individual programs
If you start at the Forums Index https://forums.adobe.com/welcome
You will be able to select a forum for the specific Adobe product(s) you use
Click the "down arrow" symbol on the right (where it says All communities) to open the drop down list and scroll -
Hi - I am looking for the Adobe Illustrator 2014 1.2 (or .0.2) bugfix update for Mac - and it is not visible in the Adobe Creative Cloud Packager (Mac version). The only update visible is Illustrator CC 2014.1 - which is what introduced the bugs.
The only thing that I can think of that might be causing the issues that I have a Mac Mini on Mavericks.
DaveHi
I have discovered that my question above is a non-question. A user triggered by looking at the below article about Illustrator 2014 cc 17.0.2
http://helpx.adobe.com/illustrator/release-note/illustrator-17-0-2-release-notes.html
He had recently upgraded from wht we now know is 18.0 to 18.1 which is the latest version. He read the above artic
le and supposed that it was a bug fix release for his version - because the v17 ov18 number is not often displayed. It is usually just 2014 CC.
I have asked him to post a bug report about Adobe Illustrator CC 2014.1
Dave -
I just purchased a mac, I've made an apple id. But now when i try to update my mac. I need to login to itunes stroe.Whenever i try that i can login, then i need to confirm my details. And suddenly the mail adress is no longer valid.
How do I solve this problem?You've posted to the iTunes Match forum, which your questions do not appear to be about. Perhaps you would get better help by posting in the iTunes for Mac forum.
-
How to update my mac book pro??
how to update my mac ???
Software Update under the Apple menu (upper left corner).
If you are at 10.6.8 then the only way to update would be purchasing Mountain Lion via the App Store application. -
How to update my mac book pro from 10.5.8 to the leatest version
how to update my mac book pro from 10.5.8 to the leatest version
Upgrading to Snow Leopard, Lion, or Mountain Lion
Upgrading to Snow Leopard
You can purchase Snow Leopard by contacting Customer Service: Contacting Apple for support and service - this includes international calling numbers. The price is $19.99 plus tax. You will receive physical media - DVD - by mail.
Third-party sources for Snow Leopard are:
Snow Leopard from Amazon.com
Snow Leopard from eBay
After you install Snow Leopard you will have to download and install the Mac OS X 10.6.8 Update Combo v1.1 to update Snow Leopard to 10.6.8 and give you access to the App Store.
Before upgrading check that you computer meets the minimum requirements:
Snow Leopard General requirements
1. Mac computer with an Intel processor
2. 1GB of memory
3. 5GB of available disk space
4. DVD drive for installation
5. Some features require a compatible Internet service provider; fees may
apply.
6. Some features require Apple’s MobileMe service; fees and terms apply.
Upgrading to Lion
First, you need to upgrade to Snow Leopard 10.6.8 as stated above.
You can purchase Lion by contacting Customer Service: Contacting Apple for support and service - this includes international calling numbers. The cost is $19.99 (as it was before) plus tax. It's a download. You will get an email containing a redemption code that you then use at the Mac App Store to download Lion. Save a copy of that installer to your Downloads folder because the installer deletes itself at the end of the installation.
Before upgrading check that you computer meets the minimum requirements:
Lion System Requirements
1. Mac computer with an Intel Core 2 Duo, Core i3, Core i5, Core i7, or
Xeon processor
2. 2GB of memory
3. OS X v10.6.6 or later (v10.6.8 recommended)
4. 7GB of available space
5. Some features require an Apple ID; terms apply.
Upgrading to Mountain Lion
Be sure your computer meets the minimum requirements:
Apple - OS X Mountain Lion - Read the technical specifications.
Macs that can be upgraded to OS X Mountain Lion
1. iMac (Mid 2007 or newer)
2. MacBook (Late 2008 Aluminum, or Early 2009 or newer)
3. MacBook Pro (Mid/Late 2007 or newer)
4. MacBook Air (Late 2008 or newer)
5. Mac mini (Early 2009 or newer)
6. Mac Pro (Early 2008 or newer)
7. Xserve (Early 2009)
Are my applications compatible?
See App Compatibility Table - RoaringApps - App compatibility and feature support for OS X & iOS.
Am I eligible for the free upgrade?
See Apple - Free OS X Mountain Lion upgrade Program.
For a complete How-To introduction from Apple see Apple - Upgrade your Mac to OS X Mountain Lion. -
Question typed in subject space. Sorry!
Hi there Amy,
You may want to take a look at the article titled "Troubleshooting Mac OS X installation and software updates (Mac OS X v10.6 and earlier)"
There is a specific section that includes this information:
Software Updates for Mac OS X and Apple applications for Mac OS X are often available in different ways:
Software Update preferences
Standalone installer from Apple Downloads.
Try getting the software from a different source, or download it again.
Hope that helps,
- Griff W. -
updated my mac to mountain lion 10.7.8.3 and now my app store, mail or facetime won't open. Also, I am not longer able to play videos through firefox. I tried downloading the combo for mountain lion and it refuses to install saying that I need to see developer. Whenever I try to open my appstore, mail or facetime it says that the programmes need to be installed and might not be compatible with this version of mac operating system. Can anyone help me?
It's not a bad install of Mountain Lion. I've had the same thing happen to me, but it affected not only Mail, but a variety of other programs including iPhoto and MS Office, where I had to delete preferences, caches, and reinstall the OS as well as the program itself. I'm still having issues with Mail, so I've gone to another program.
Everything was fine upon the initial install. I restarted my iMac about two weeks after the install, and that's when the issues began to happen. I've reinstalled Mountain Lion twice, but the same issues arise.
As I mentioned above, you'll need to figure out which preferences are causing the issue, then reinstall the program, as a fresh reinstallation will do you no good unless you wipe the drive completely.
Here's a thread that helped me with iPhoto:
https://discussions.apple.com/thread/4794375?start=0&tstart=0 -
I update my Mac to version 10.9.2 and now my printer does not work anymore. I did all the software updates and I do not understand why my mac does not recognize the printer anymore?
Go to the website of the manufacturer of your printer and check to see if they have released an updated driver for your particular model.
-
Hi,
My Adobe CS 4 ran perfectly find up until I updated my MAC OS from Mavericks to the new YOSIMITE. When I launch illustrator CS4 I get a window message the reads "some plug-ins in the additional Plug-ins folder are conflicting with application or user plug-ins. It will skip loading plug-ins from additional plug-ins folder." there is a OK button that I must click on to close the message window and then illustrator will continue loading process, then a second window will appear reading "Error loading plug-ins. PhotoshopImport.aip" there is a OK button that I must click on to close the message window and then illustrator will continue loading and launch.
The problem is when I open a current file that has a psd link I will get a window message reading "could not find a plug-in to read the link file _______ choose repair to locate the missing file, replace to select another file, or ignore to leave the link unchange." When selecting a psd link /file it is greyed out which I cannot select it. I can not select, choose, import or open any files/links that is a psd.
Would someone please help me resolve this issue please!!!I have the same issue! Did you get a solution yet?
-
i just updated my mac and when i went to open iphoto it says it "can not open because of a problem" how do i fix this?
To re-install iPhoto
1. Put the iPhoto.app in the trash (Drag it from your Applications Folder to the trash)
2a: On 10.5: Go to HD/Library/Receipts and remove any pkg file there with iPhoto in the name.
2b: On 10.6: Those receipts may be found as follows: In the Finder use the Go menu and select Go To Folder. In the resulting window type
/var/db/receipts/
2c: on 10.7 they're at
/private/var/db/receipts
A Finder Window will open at that location and you can remove the iPhoto pkg files.
3. Re-install.
If you purchased an iLife Disk, then iPhoto is on it.
If iPhoto was installed on your Mac when you go it then it’s on the System Restore disks that came with your Mac. Insert the first one and opt to ‘Install Bundled Applications Only.
If you purchased it on the App Store you can find it in your Purchases List. -
I have Microsoft Office 2004 on my MacBook (2.4 GHz Intel Core 2 Duo). It is currently up to date with Microsoft updates. I am running Mac OS 10.6.8. I just updated my Mac software with "Security Update 2012-001". I am now unable to print (Epson NX510 printer) from Excel or Word. When I click on the Print menu item in Excel, there is a flash in the background like it is trying to open the print window, but nothing else. I am able to print from other programs like TextEdit, Mail or KakeidaGraph. As far as I know I have the latest Epson print driver.
Also, I am also unable to open an existing Excel or Word file from the open menu - both programs lock up and do not respond. I have to force quit. After I restart Excel or Word I can open an existing file by double clicking on the file, but if I again try to open another file from the open menu, Excel or Word lock up.
Any similar problems?Howdy,
Apparently some are reporting that this causes the older PowerPC (PPC) applications that are supported in 10.6 via 'Rosetta' to crash upon attempting to open/save/print using any dialog box, or fail in other similar ways such as simply not printing or quitting, or freezing/hanging/crashing of the application.
I have read of some companies that have indeed submitted proper bug reports to Apple, but that is not a guarantee of a bug-fix being issued.
You might wish to read:
http://www.macintouch.com/readerreports/snowleopard/index.html#d02feb2012
If you are unsure if you are still using PowerPC apps, if the application is currently running, look under the 'Activity Monitior' (in Applications -> Utilities), or alternatively you could check in the System Profiler, Applications. Check the column "Type".
Here is a fairly simple way you can restore you system and restore you applications functionality again, if you don't have a recent clone or good Time Machine backup that you can restore from. If you do, restore from your backup prior to having installed the Security Update 2012-001.
Time Machine restore: http://support.apple.com/kb/ht1427
If you are restoring a backup made by a Mac to the same Mac
With your backup drive connected, start up your Mac from the Lion recovery partition (Command-R at startup) or Mac OS X v10.6 installation disc. Then use the "Restore From Time Machine Backup" utility. Select the backup prior to your issues, and it will be restored back to the state it was in at that time.
If you can't easily restore from a backup, you can instead do the following:
- You first start by reinstalling your OS X 10.6.x, this will preserve all your user data, your applications, no worries there.
- Then install the Mac OS X 10.6.8 Update Combo v1.1 (links provided below)
- Make sure you're printers are showing up correctly in your system preferences, if not, re-add the printers
- Then finally, run the Apple Software Update (by pulling down the Apple Menu), and install any and all remaining updates, except do not then re-install the Security Update 2012-001. It is possible that you may have to reboot after installing some of the updates, and you may even need to run it a 2nd time to make sure that you've got all updates, except NOT the Security Update 2012-001.
Links for 10.6.8 Update Combo v1.1:
http://support.apple.com/kb/DL1399
or the link to directly download this 1.09GB combo updater:
http://support.apple.com/downloads/DL1399/en_US/MacOSXUpdCombo10.6.8.dmg
Cheers,
Daniel Feldman
=======================
MacMind
Certified Member of the
Apple Consultants Network
Apple Certified (ACHDS)
E-mail: [email protected]
Phone: 1-408-454-6649
URL : www.MacMind.com
======================= -
I updated my Mac Book Pro to Yosemite, now it says it's not compatible with my Cannon copier. Any ideas how to fix this problem so I can use my Cannon copier again? Thanks for any help!
If MF4150 is correct...
http://www.usa.canon.com/cusa/home
search MF4150
click >Drivers & Software
Verify or choose Yosemite 10.10 - then click the [+]
Again verify Yosemite > click agree > click [DOWNLOAD]
The rest should be self-explanatory
ÇÇÇ
Maybe you are looking for
-
when i try to uninstall quicktime it says that there is a fatal error and wont uninstall! anyone know what i can do to get quick time completely off my computer? ive tried deleting the two files and all that. when i install the new itunes, i try to o
-
I am new to Pagemaker and Im trying to create a little flyer for my youth group. The images are all jpegs, and when I use the 'Place' option they were showing up fuzzy. So I changed the view to 'high resolution' and now they look great on screen. But
-
How do i find the list of data achived in the system. i mean is ther any specific table or program for that
-
Hi All, I have a configured data guard in my local system . Please find the below configuration of the Data guard Data Guard Type : - Physical Standby (Oracle version 11g) Service Responsible for Log Transport : - ARCH No Standby Redo log : - Neithe
-
Updating HRP1001 while running actions
Hi Experts, While running actions the om infotypes like IT1001 is updated. Could You please tell me as where this configurations are made? Like while running a hire action there is a P-A008-S relation created in HRP1001, where is it configured that w