Mac OS X Server: Stuck on grey screen

I installed a Mac OS Server 10.5.4 onto Mac Pro Duo core workstation it has 2GB RAM. I'm using this machine as a storage machine for video. I have a Lacie Big Drive firewire and 5big Network hard drive. I disconnected the drives. I ran a disk utilities to repair permission then reboot. I used Energy Saver Schedule to reboot the machine once a week, and I notice it was reindex the whole time. It tried to reboot, but it got stuck during the boot up and I see grey Apple with spinning dial. I tried to do a cold boot three times and no luck. Also I tried safe which I don't fully understand it or succeeded in being that mode. I'm a novice at Mac OS X server.
Does anyone have any solution?
Thanks
Luis
Message was edited by: Luis Casale

I have not follow this method. I install the simple version of installation and setup groups, users. Since, I did not have the time do to any maintenance and spotlight was trying to reindexing, we had tons of videos files. Before grey went to grey screen, Spotlight was trying to re-indexing. I went ahead to schedule a restart once a week on Saturday. I found the machine with the grey screen and I waited for for two hours. I decide to try cold boot, didn't work and I even tried the started up disk. No luck! I been searching online for answers. Thank you for responding. I'm new on the server side. Don't have any one else who is an expert on Mac Server.
Thanks
Luis

Similar Messages

Mac won't boot, stuck on grey screen if the external hdd plugged in

as the title.
if i plug my external drive, via usb port, the mac won't boot and stuck at grey screen.
unplugging it, the boot process will continue.
the hdd is a LaCie mobile hdd
any help?

Hello jason(?)
It's a LaCie external mobiel hdd, formatted as exFAT. without adapter. take power directly from usb port.
i tested it on my iMac and it works fine. boot up as normal. the only difference is my iMac is on 10.6.8 and my Air is on 10.7.2
I tested on both USB port on my Air and the problem still persist.
the read/write speed is normal (bought it like a day ago).
another thing is I don't have this problem with my external WD drive.
One thing to notice is that, I accidentally left like for like 2-3 mins and it boots. So why the question now is why it's taking so long to boot? normally it just takes <20 seconds. Seems like it tried to boot from the external hdd, doesn't it?

Mac Pro 3,1 Stuck on Grey screen for 1 min during boot

I have a Late 2008 Mac Pro 3,1 and have started experiencing a very slow boot up. The computer gets stuck for over a minute on the initial gray screen after the first boot chime. Once the apple logo finally appears the boot goes normally. Once running it seems OK. The shut down seems normal with a grey screen for a few seconds with the "clock" logo.
Symptom:
After the chime I see a blank gray screen for in excess of 1 minute, it used to last only a couple of seconds.
Once the dark grey Apple logo appears the boot goes at normal speed
I have a number of different hard drives with older systems and booting from each of then gives the problem - so it does not seem to be system/disc related
Two partitions (Mavericks and ML) are on SSD's installed on a Sonnet PCIe Card and showed the same problem as the spinning hard discs.
I tried: (following a trawl of the bb's etc)
I repaired permissions and repaired all discs for all my boot partitions (10.5, 10.6, 10.7, 10.8 and 10.9) using the appropriate Disc Utility
Zapping the Pram - this was very strange as I had to keep the cmd alt P R held down for around a minute before the second chime occurred, the time of the grey screen stays stuck
Resetting the SMC
Booting in Verbose Safe Mode: Again I had to hold the Alt V down for a minute on the gray screen before the screen went black and the text appeared
I looked on the console log but could see nothing obvious, additionally from the verbose safe mode boot the text log seems to start from when the grey screen disappears. The time stamps show the boot finishing in well under the minute I wait.
Any suggestions you may have are very welcome.
Regards
Dave

Thanks The Hatter for that information. The blank gray screen is now lasting 3 mins before the Apple appears. When I restarted the system log is as below. As you can see there is just over a three minute gap between the shut down and the boot, indicating to me that it is not something in the system software after the boot but a problem at the very start. It does look like it could be something to do with the hardware as you suggest. I have verified all the discs with the disc utility and they report as OK and their SMART status is also OK. I have disconnected the external drives with no change so I will now have to do a thorough check and systematically remove the internal ones but that will have to wait for the weekend.
I have Mavericks on the Samsung 840 Pro and ML on a Crucial SSD (Crucial_CT240M500SSD1 Media) on a PCIe card. The Mavericks install I think was an upgrade, not a clean install done quite a while ago. I only noticed the problem this week when I re-booted in an ML to run some software not compatible with Mavericks. I have made a system back up as a precaution to an external disc just in case my main drive is dying!
There are some firmware updates for both the SSD discs that I have not applied these yet but I will leave them out of the mix until I have tried simplifying my configuration with a single disc.
Apr 21 22:09:26 Davids-Mac-Pro.local shutdown[952]: reboot by _spotlight:
Apr 21 22:09:26 Davids-Mac-Pro kernel[0]: Kext loading now disabled.
Apr 21 22:09:26 Davids-Mac-Pro kernel[0]: Kext unloading now disabled.
Apr 21 22:09:26 Davids-Mac-Pro.local shutdown[952]: SHUTDOWN_TIME: 1429650566 934799
Apr 21 22:09:26 Davids-Mac-Pro kernel[0]: Kext autounloading now disabled.
Apr 21 22:09:26 Davids-Mac-Pro kernel[0]: Kernel requests now disabled.
Apr 21 22:09:26 Davids-Mac-Pro.local Mediatap[297]: XPC error messaging com.apple.IconServicesAgent: Connection interrupted
Apr 21 22:09:26 Davids-Mac-Pro.local Mediatap[297]: XPC error messaging com.apple.IconServicesAgent: Connection invalid
Apr 21 22:13:02 localhost bootlog[0]: BOOT_TIME 1429650782 0
Apr 21 22:13:04 localhost syslogd[18]: Configuration Notice:
ASL Module "com.apple.appstore" claims selected messages.
Those messages may not appear in standard system log files or in the ASL database.
Apr 21 22:13:04 localhost syslogd[18]: Configuration Notice:
ASL Module "com.apple.authd" sharing output destination "/var/log/system.log" with ASL Module "com.apple.asl".
Output parameters from ASL Module "com.apple.asl" override any specified in ASL Module "com.apple.authd".

TS2570 My Mac is stuck on grey screen what's wrong with it and am I going to lose everything

My Mac is stuck on grey screen what's wrong with it and am I going to lose everything

Hopefully you have a backup, but...
Could be many things, we should start with this...
"Try Disk Utility
1. Insert the Mac OS X Install disc, then restart the computer while holding the C key.
2. When your computer finishes starting up from the disc, choose Disk Utility from the Installer menu at top of the screen. (In Mac OS X 10.4 or later, you must select your language first.)
*Important: Do not click Continue in the first screen of the Installer. If you do, you must restart from the disc again to access Disk Utility.*
3. Click the First Aid tab.
4. Select your Mac OS X volume.
5. Click Repair Disk, (not Repair Permissions). Disk Utility checks and repairs the disk."
http://docs.info.apple.com/article.html?artnum=106214
Then try a Safe Boot, (holding Shift key down at bootup), run Disk Utility in Applications>Utilities, then highlight your drive, click on Repair Permissions, reboot when it completes.
(Safe boot may stay on the gray radian for a long time, let it go, it's trying to repair the Hard Drive.)
If perchance you can't find your install Disc, at least try it from the Safe Boot part onward.

Mac book air stuck on grey screen with apple logo and spinning wheel

I had a lot of tabs open and several applications as well. things really slowed up when I added El media player to the mix. finally computer froze completely and now can't get it to restart (stuck on grey screen) tried SMR plus PRAM procedures without success.

Hmm... try doing this:
1) Force your Mac to shut down by pressing and holding the power button for about 5 sec.
2) Start in Safe Mode. Press the power button to turn it on, and before you hear the Startup "Dummmmm" chime, hold down the Shift key. For a few sec, you won't see the Apple logo. Keep pressing the Shift key until you see it. If you press it after the Apple logo appears, start from Step 1 again.
3) This time, your Mac should take longer to boot. (Like a minute or 2 longer as it is going thru the necessary files to boot from, and not just everything like in Normal Startup mode; which caused it to hang)
4) Does your Mac boot sucessfully to the Login Screen or Desktop? The login Screen should show SAFE MODE in red at the top. The Desktop should have Sound disabled and seems a lot slower. If you see either of these, backup ALL your files (if you have not already done so) on to an External HDD. Create a new User Account in System Preferences>Accounts with about the same info as your current account (The name will have to be different though, if your previous account was John, this time, add your last name as in John Appleseed.) Make sure it is an Admin account. Then, login into the new account and delete your previous account. Copy all your files over to your new account and restart your Mac correctly by going to Apple Menu>Restart.
5) This time, don't press anything and let it boot normally. Does your Mac boot correctly? I hope that helps you a little. Get back to me if it does not work!

Mac Pro Stuck at Grey Screen, then will only boot into OS X Utilities.

My Mac Pro is stuck at Gray Screen. When I reset PRAM, it loads the OSX Utilities screen, prompting me Restore from Time Machine, Reinstall OS X, Get Help, or Disk Utility. I ran Disk Repair and Repair Premissions, same thing.... stuck at grey screen.
What will happen to the data on my HD if I choose to Reinstall the OS X? IS that the best choice? Thanks.

Off hand I think your drive may be bad. But to find out you need to erase the drive, so you will need to have a recent, bootable backup.
Install or Reinstall Lion/Mountain Lion from Scratch
Be sure you backup your files to an external drive or second internal drive because the following procedure will remove everything from the hard drive.
Boot to the Recovery HD:
Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
Erase the hard drive:
1. Select Disk Utility from the main menu and click on the Continue button.
2. After DU loads select your startup volume (usually Macintosh HD) from the
      left side list. Click on the Erase tab in the DU main window.
3. Set the format type to Mac OS Extended (Journaled.) Optionally, click on
        the Security button and set the Zero Data option to one-pass. Click on
      the Erase button and wait until the process has completed.
4. Quit DU and return to the main menu.
Reinstall Lion/Mountain Lion: Select Reinstall Lion/Mountain Lion and click on the Install button.
Note: You will need an active Internet connection. I suggest using Ethernet if possible
            because it is three times faster than wireless.
If this does not work, then you need to replace your hard drive.

My old mac powerbook g4 wont boot up, it wont show apple logo and spinner aswell just stuck on grey screen while booting please help me

i have a old powerbook g4 which i usally use to store some photos and to listen music. the battery of my powerbook is completly dead so i used to use my powerbook using charger adapter so whenever my power cuts down my laptop will be shutdown.
one day i had just bootedup my powerbook and some date notificateion poped up so i press enter and suddenly my power went off and laptop shuted down. and next time when i tried to boot its stuck at grey screen , i even cant reach the apple logo and spinner. please helppp me :!!!!!!!!!!!!!!!

Resetting PRAM and NVRAM is not working
and i cann't boot it on safemode holding shift button and while holding option or c button at startup i can only see three things 1 is refresh button, 2 macintosh HD with X under it, 3 arrow forward button please help me

Need Help For iMac G5 Stuck On Grey Screen Or Apple Logo No Spinning Gear!

Hello everyone i'm new here and i'm new for using iMac for some reason i was trying to clean or to fresh installation the iMac that my brother gave it to me that he bought it into the flea market without the original disk on it! when i erase the Macintosh HD and some of the partition o iMac then reboot it now the iMac stuck on grey screen or apple logo no spinning wheel shown. and i also try to search and try all the tips of all mac user's like all the command key's and follow the instruction of them but still nothing happen..
Holding CMD & R just to go disk utilities nothing shown up only apple logo and the noisy fan.
Holding alt and it go to blue screen and show my mouse Pointer Refresh Logo, Hard drive Icon, Arrow Sign.
i can click Arrow Sign and it go Apple Logo and within 2-3 seconds and it change to Power Sign Logo,
i can click Refresh Logo but nothing happen .
i can't click the Hard Drive icon.
CMD, Option, P & R to Reset i also try and it's the same nothing change.
CMD, Option, ESC no action shown.
Is there anyway to fix this issue or problem please and thank you for help.
Hoping to get result for all of you guys P.S
iMac G5
v10.5.8
Leopard

You need to have the install DVD that was issued with the iMac
You can call Apple at 1-800-275-2273

Powermac G5 stuck on grey screen start up and fans running wild

Hi All
I also have the recurring problem all of a sudden - yesterday all seems well, today am stuck on grey screen and fans getting stronger by the minute. NOTHING works - have been through all sorts of forums and the most I got was to try disk utility - which says all is well - replaced the battery - tried just about anything short of pouring some acid on the **** thing, won't boot from original install CD either - I really need this machine as I earn my living with it and cant afford a new one and why as it was working just perfect - now this mess. In a way don't know why the excellerating fans are not built to simply pick up speed and then eat into the PC board and CPU - at lest this way we know for sure there is nothing we can do.
Does no one here know why the mac is doing this - not even the mac fundies? Unbelievable. I live in Namibia and Apple Mac support here is similar to that on this website - might as well write this on a wall - that is why I am really frustrated... **** Mac

Follow these steps in order:
http://support.apple.com/kb/TS2570
The G5 is also subject to solder failure around the RAM slots and memory controller.
It is a fatal condition, but one that can sometimes be temporarily sidestepped by heating the logic board between the RAM slots with a hair dryer.
Heat the board until very warm (hot) then start.
If your machine starts after heating, then you better just leave the machine on all the time.
You never know when the trick won't work......

STUCK ON GREY SCREEN! !PLEASE HELP!

!!HELP!! STUCK ON GREY SCREEN
I have a MacBook 10.5. Its a few years old anyway it seemed to be working fine up until a couple of weeks ago then it started taking ages to startup.
I started it in singlemode then typed /sbin/fsck -fy then a message came up "harddrive appears to be ok" next i typed "reboot" and the system started booting.It started as normal with the apple logo and spinning chime,next the screen turns blue where the login screen normally appears but then the screen turns grey with no logo with just the pointer arrow on it and it doesn't seem to load past that point.Can anybody please help me solve this problem i have my kids photos and stuff on it that are unreplaceable.
Hopefully there's a command line that can help also I don't have a installation disk so is there a way I can download 1 onto USB??
THANKS HEAPS!!!!!

Hi Eug07349,
Thanks for visiting Apple Support Communities.
It sounds like you may be experiencing a software issue. I'd suggest trying the first two steps in this article (Disconnect, test peripheral devices and network cables, Perform a Safe Boot):
Mac OS X: Gray screen appears during startup
http://support.apple.com/kb/ts2570
Best,
Jeremy

Powermac g5 won't boot mac os 10.5 stuck at logo screen

Anyone experience this problem? How do I fix it?
PowerMac G5 wont startup. gets stuck on grey screen with apple logo with no turning gears, then fans start blowing really loud.
Using latest Mac OS 10.5
It will not start up from an install disc, but will run the hardware tests.
All tests pass in G5 hardware test disc.
Hard drives have passed all tests, been rebuilt and repaired permissions.
I have tried starting up in safe mode, holding down the option key to select a drive and holding down the c key to startup with an install disc.
The battery was dead so I replaced it but it still wont boot.
I tried zapping the PRAm still not booting up.
I have attempted to use terminal but get the following message then there is no response.
Darwin Kernel Version 9.8.0: Wed Jul 15 16:57:01 PDT 2009;
root: xnv-1228.15.4~1/Release_PPC
Standard timeslicing quantum is 10000 US
VM_page_bootstrap: 1021219 free pages and 27,357 wired pages
mig_table_max_displ = 79
Extension "com.apple.driver.Apple Mac Risc4PE" has immediate dependencies on both com.apple.kernel and com.apple.kpi components use only one style
Loading security extension com.apple.security. TmSafetyNet
calling mpo_policy_init for TmSafetyNet
Security policy loaded Sfety net for Time Machine (tmSafetyNet)
Loading security extension com.apple.nke.applicationfirewall
Loading security extension com.apple.security seatbelt
calling mpo_policy_init for mb
Seatbelt MACF policy initialized
Security policy loaded: seatbelt policy (mb)
Copyright (c) 1982 1986 1989 1991 1993 The Regents of the University of California. All rights researved
Mac Framework successfully initialized
Using 16384 buffer headers and 4096 cluster 10 buffer headers
DART enabled

Mac OS X: Gray screen appears during startup

Macbook pro retina 2012 mid year stuck on grey screen

Hi everyone.
I've just update for the lastest mac os x mountain lion update, when half way the progress and it goes stucked. All the function are unable to function, so i've force shut it down. After mac shutted down and i tried to boots it back it stuck on grey screen which below apple logo forever loading icon. i've tried Reset the PRAM, but it still not working for me. Also, i tried when when start up hold with cmd + r to reinstall the os x , but it just won't let me to reinstall it , it wrote you can't upgrade this version of OS X because a newer version is installed?
Help please! need a solution that wont delete all my files at the same time

Take each of these steps that you haven't already tried. Stop when the problem is resolved.
Step 1
The first step in dealing with a boot failure is to secure your data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since your last backup, you can skip this step.
There are several ways to back up a Mac that is unable to boot. You need an external hard drive to hold the backup data.
a. Boot into the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.”
b. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, boot the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
c. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to boot, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can boot now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
If you've booted from an external storage device, make sure that your internal boot volume is selected in the Startup Disk pane of System Preferences.
Step 3
Boot in safe mode. Note: If FileVault is enabled on some models, or if a firmware password is set, or if the boot volume is a software RAID, you can’t do this. Post for further instructions.
Safe mode is much slower to boot and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
When you boot in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, your boot volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 5.
If you can boot and log in now, empty the Trash, and then open the Finder Info window on your boot volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then reboot as usual (i.e., not in safe mode.)
If the boot process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 4
Sometimes a boot failure can be resolved by resetting the NVRAM.
Step 5
Launch Disk Utility in Recovery mode (see Step 1.) Select your startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then reboot as usual.
Step 6
Reinstall the OS. If your Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Step 7
Repeat Step 6, but this time erase the boot volume in Disk Utility before installing. The system should automatically reboot into the Setup Assistant. Follow the prompts to transfer your data from a Time Machine or other backup.
Step 8
This step applies only to older Macs (not current models) that have a logic-board ("PRAM") battery. Both desktop and portable Macs used to have such a battery. The logic-board battery is separate from the main battery of a portable. A dead logic-board battery can cause a gray screen at boot. Typically the boot failure will be preceded by loss of the startup disk and system clock settings. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
Step 9
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store to have the machine tested. If you can't get to an Apple Store, go to another authorized service provider.

10.6 won't boot; stuck on grey screen

I know this is covered here to some degree, at least, but I haven't been able to find a complete solution/answer, so here goes:
(Please, redirect me to the right source of information, if you know where to look, but not before reading through my post. Thanks! Oh, and I'm no computer expert, so, please, bear with me.)
First of all, my equipment: 17" iMac (serial #: w86262cru2n, emc #: 2104), running (ran?) 10.6 (w/updates)
So, as my title says, my iMac won't boot up and gets stuck on the grey startup screen with the  and the spinning wheel. I can wait and wait, but it never gets past this point.
Here are some things I've tried (nothing has worked so far; "no success" = stuck on grey screen). These steps are also laid out here.
- Tried normal startup (no success)
- Tried Safe Boot (no success)
- Tried booting without connected peripherals (no success)
- Tried alternate outlet (power source) (no success)
- Tried resetting PRAM & NVRAM (no success)
- Tried boot from 10.6 Install Disk (no success)
- Tried replacing original RAM (no success)
- Tried mounting internal drive as Target Disk on my 10.5 MacBook (mounts fine; used 10.6 install disk to verify, says disk is "ok")
- Tried booting to MacBook via Target Disk (i.e. iMac is external drive connected by FireWire) (no success)
- Tried booting from cloned copy of 10.6 disk on an external USB drive (yes, this can be done; I've done it before). This drive was verified "ok" in the same way the internal disk was (see above). (no success)
My next step appears to be to erase the original internal HD and reinstall 10.6. This is where my my ignorance begins to rear it's head. Since I can seem to boot from the iMac, can I do this through my MacBook, viz. mount the original, internal, 10.6 disk on my MacBook and erase it and install 10.6 from there (e.g. through Disk Utility on the 10.5 MacBook)?
Assuming this is possible, can someone step me through the process?
Assuming this last step isn't possible, does this all point to a faulty logic board (sounds like a 'worst case' to me)?
Any ideas? Suggestions?
Many, many thanks, BTW, to all who have posted here and whose help I've availed myself of anonymously many times. And thanks in advance to anyone with helpful ideas.

Try a SMC reset and follow the steps again in the support doc for grey screen
https://support.apple.com/kb/ht3964
https://support.apple.com/kb/TS2570
Your 10.6 install disk seems unreadable if it won't "hold c or option" boot.
Clean the bottom with a alcohol and a very soft cloth and lightly polish until there is no streaks.
Don't touch the bottom or place the disk onto something that will mar the bottom.
If the disk still fails to work, get a replacement, as your going to need it. Get a jeweled plastic case for it.
To make copies of your Snow Leopard install disk, follow these directions.
http://www.walterjessen.com/make-a-bootable-backup-snow-leopard-install-disc/
Once you can hold c and boot off a working 10.6 install disk, simply reinstall OS X without using Disk Utility to Erase and Format the drive, this will replace the OS X installed (and bundled programs) with the disk versions, then reboot and immediately use Software Update to get current.
Your user files, third party programs will remain untouched, except for ones installed in OS X/root system files, those will have to be reinstalled with updated copies.
All else fails:
Grab a copy of your recent user file folders via FireWire target disk mode first or from a hold option bootable clone on a external drive
If you have to completely erase and reformat the drive, reinstall 10.6, there are some things you need to know.
1: The free iLife that came with your 10.5 install disks are not on the 10.6 retail disks
So to get that you need to select the drive makers name in Disk Utility, erase and install with the 10.5 disks first (warning, wipe entire drive)
2: Name the boot drive the same name as before in Disk Utility when formatting.
3: When you go through inital "Welcome to Mac" setup, use the same username as before, (different password)
4: Once in OS X 10.5 stick a working 10.6 installer disk in and upgrade. Once rebooted, immediately Software Update to current version.
5: Install programs from fresh sources next and update.
6: Finally, return the backup copies of your user file folders (Music, Documents, Pictures, etc., not Library) to their respective folders on the new configuration. Because you used the same hard drive and user name as before you should have little complications with things like iTunes song locations/playlists and other hard references to files on your drive.
By installing the OS first, then upgrading, then programs, then finally user files last, keeps the drive optimized as the drive is faster on the data installed first than data installed later. Since users files change size often, having them towards the end where they can grow or shrink keeps the performance of the computer up as much as possible for the OS and applicaitons. Eventually though with OS X updates it can get a bit more defragmented, but not much.

Hello my Mac Air is frozen on the grey screen (with the apple symbol, sleeping mode, restart-and off button), once you turn it on.

hello my Mac Air is frozen on the grey screen (with the apple symbol, sleeping mode, restart-and off button), once you turn it on. I Can`t press any button.My Mouse still works. Battery is charged. Alt-cmd-escape doesn`t work It even after a forced shutting off, the problem is the same.   what should i do? Thank you for your help.

Take each of these steps that you haven't already tried. Stop when the problem is resolved.
Step 1
The first step in dealing with a boot failure is to secure your data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since your last backup, you can skip this step.
There are several ways to back up a Mac that is unable to boot. You need an external hard drive to hold the backup data.
     a. Boot into the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.”
b. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, boot the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
c. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to boot, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can boot now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
If you've booted from an external storage device, make sure that your internal boot volume is selected in the Startup Disk pane of System Preferences.
Step 3
Boot in safe mode. Note: If FileVault is enabled, or if a firmware password is set, or if the boot volume is a software RAID, you can’t do this. Post for further instructions.
Safe mode is much slower to boot and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
When you boot in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, your boot volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 5.
If you can boot and log in now, empty the Trash, and then open the Finder Info window on your boot volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then reboot as usual (i.e., not in safe mode.)
If the boot process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 4
Sometimes a boot failure can be resolved by resetting the NVRAM.
Step 5
Launch Disk Utility in Recovery mode (see Step 1.) Select your startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then reboot as usual.
Step 6
Reinstall the OS. If your Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Step 7
Repeat step 6, but this time erase the boot volume in Disk Utility before installing. The system should automatically reboot into the Setup Assistant. Follow the prompts to transfer your data from a Time Machine or other backup.
Step 8
This step applies only to older Macs (not current models) that have a logic-board ("PRAM") battery. The battery is distinct from the main battery of a portable. A dead logic-board battery can cause a gray screen at boot. Typically the boot failure will be preceded by loss of the startup disk and system clock settings. See the user manual for replacement instructions.
Step 9
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store to have the machine tested.

Intel-based iMac stuck in grey screen with spinning wheel. SMC::smcReadKeyAction ERROR THOP kSMBadArgumentError(0x89)

Hi guys,
since yesterday my Intel-Based iMac doesn't boot normally, its stuck in grey screen with a spinning wheel.
Its an Intel-based iMac 21.5'' purchased in 2011, and i recently (2 months ago) upgraded it to Mavericks.
-2 weeks ago, i installed smcFanControl app
-Tried start up in Safe Mode by holding Shift but its not working. i think i hear fans are working more than they were before the problem occurs.
-entered Single User Mode and i get an error
SMC ::smcReadKeyAction ERROR THOP kSMCBadArgumentError(0x89) fKeyHashTable=0x0xffffff8029fa1000
-followed some instructions found online, but can execute the correct commands in SingleUserMode
tried to remove FanControl as explained here: http://apple.stackexchange.com/questions/110667/errorr-kernel-smcsmcreadkeyactio n-in-console
any ideas what may caused this and how can i fix this?
Thanks in advance

Take each of these steps that you haven't already tried. Stop when the problem is resolved.
Step 1
The first step in dealing with a startup failure is to secure the data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since the last backup, you can skip this step.
There are several ways to back up a Mac that is unable to start. You need an external hard drive to hold the backup data.
a. Start up from the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.” The article refers to starting up from a DVD, but the procedure in Recovery mode is the same. You don't need a DVD if you're running OS X 10.7 or later.
b. If Step 1a fails because of disk errors, and no other Mac is available, then you may be able to salvage some of your files by copying them in the Finder. If you already have an external drive with OS X installed, boot from it. Otherwise, if you have Internet access, follow the instructions on this page to prepare the external drive and install OS X on it. You'll use the Recovery installer, rather than downloading it from the App Store.
c. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, start the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
d. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
If the startup process stops at a blank gray screen with no Apple logo or spinning "daisy wheel," then the startup volume may be full. If you had previously seen warnings of low disk space, this is almost certainly the case. You might be able to start up in safe mode even though you can't start up normally. Otherwise, start up from an external drive, or else use the technique in Step 1b, 1c, or 1d to mount the internal drive and delete some files. According to Apple documentation, you need at least 9 GB of available space on the startup volume (as shown in the Finder Info window) for normal operation.
Step 3
Sometimes a startup failure can be resolved by resetting the NVRAM.
Step 4
If you use a wireless keyboard, trackpad, or mouse, replace or recharge the batteries. The battery level shown in the Bluetooth menu item may not be accurate.
Step 5
If there's a built-in optical drive, a disc may be stuck in it. Follow these instructions to eject it.
Step 6
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to start up, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can start up now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
Step 7
If you've started from an external storage device, make sure that the internal startup volume is selected in the Startup Disk pane of System Preferences.
Start up in safe mode. Note: If FileVault is enabled, or if a firmware password is set, or if the startup volume is a Fusion Drive or a software RAID, you can’t do this. Post for further instructions.
Safe mode is much slower to start and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know the login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
When you start up in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, the startup volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 10. If you ever have another problem with the drive, replace it immediately.
If you can start and log in in safe mode, empty the Trash, and then open the Finder Info window on the startup volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then restart as usual (i.e., not in safe mode.)
If the startup process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 8
Launch Disk Utility in Recovery mode (see Step 1.) Select the startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then restart as usual.
Step 9
Reinstall the OS. If the Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Step 10
Do as in Step 9, but this time erase the startup volume in Disk Utility before installing. The system should automatically restart into the Setup Assistant. Follow the prompts to transfer the data from a Time Machine or other backup.
Step 11
This step applies only to models that have a logic-board ("PRAM") battery: all Mac Pro's and some others (not current models.) Both desktop and portable Macs used to have such a battery. The logic-board battery, if there is one, is separate from the main battery of a portable. A dead logic-board battery can cause a startup failure. Typically the failure will be preceded by loss of the settings for the startup disk and system clock. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
Step 12
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store, or go to another authorized service provider.

Mac OS X Server: Stuck on grey screen

Similar Messages

Maybe you are looking for