Mac OSX 10.7.5 update failed to save?

Hi,
I've been getting this message every single time i try to update my software and it's driving me mental!
''The update could not be verified. It may have been corrupted or tampered with during downloading. The update will be downloaded and checked again the next time that Software Update runs.''
I honestly have no idea on what to do. All the discussions about this issue date back to 2012, I was wondering if anyone had a more up to date solution/advice?
Greatly appreciated!

If you have more than one user account, these instructions must be carried out as an administrator.
Launch the Console application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Console in the icon grid.
Select "/var/log/install.log" from the file list on the left. If you don't see that list, select
View ▹ Show Log List
from the menu bar. Then select the messages from the last installation or update attempt, starting from the time when you initiated it. If you're not sure when that was, start over and note the time. Copy them to the Clipboard (command-C). Paste into a reply to this message (command-V).
If there are runs of repeated messages, post only one example of each. Don’t post many repetitions of the same message.
When posting a log extract, be selective. Don't post more than is requested.
Please do not indiscriminately dump thousands of lines from the log into this discussion.
Important: Some private information, such as your name, may appear in the log. Edit it out by search-and-replace in a text editor before posting.

Similar Messages

Mac OSX 10.5.6 update fails every time

Hi,
I recently did a defrag on my macbook pro and reinstalled it from the leopard disk. And so it was reset to mac OSX 10.5, now every time I try the combined update to 10.5.6 it fails, I tried twice with the updated deleting in after the first try. I then downloaded it from the downloads but to no avail.

Hello and welcome to the discussions. Just recently the 10.5.6 combo update was revised to allow the update from 10.5.0. Before it was required 10.5.1 to update using the 10.5.6 combo. Try updating to 10.5.1 then run the 10.5.6 combo.
You can download 10.5.1 here:
http://support.apple.com/downloads/MacOS_X_10_5_1Update
Hope it works for you,
Glynn

Installing dreamweaver on mac air osx. Message appears update failed the patch is not applicable to you

Can't install dreamweaver on new mac air osx Keep getting message Update failed This patch is not applicable to you.

Dreamweaver download prob which version of Dreamweaver are you trying to install? What version of Mac OS do you have installed on your new MacBook Air? Finally what specific update is failing?

Stuck with Apple Mac OSX 1.7.2 update!

My MacBook Pro Early 2011 is stuck on the Mac OSX 1.7.2 update.
I ordered Lion OSX from App Store about 2/3 months ago.
It says:
Software Update
Installing 3 items
Progress Bar
This may take a few minutes; do not shut down your computer.
And it has been going about 45min. on the same screen.
And i don't have a Time Machine recovery and don't want to lose my data.
PLEASE HELP!!!

I have solved my problem!
I just shut it down with the power button.
Waited 10 minutes (i kept trying before but did not start up).
I started it then it restarted about 4 times then it started up with all my data.

Hi on MAC OSX 10.7.4 update on Aperture 3.3.1 has been done, still gget the error message "By opening the databank for the Mediathek „~/Pictures/Aperture Library.aplibrary" is an error" is anybody out there to help me?

Hi on MAC OSX 10.7.4 update on Aperture 3.3.1 has been done, still gget the error message "By opening the databank for the Mediathek „~/Pictures/Aperture Library.aplibrary“ is an error" is anybody out there to help me?

Alex,
did you just upgrade from an Aperture 3.2.x version to Aperture 3.3.1? This error message usually occures after the upgrade to 3.3.1, when Aperture cannont convert the library format to 3.3. format.
I'd try to repair the Aperture Library (Mediathek), before upgrading it. Hold down the option-command key combination (⌥⌘) while double-clicking Aperture. This will bring the "Aperture Library First Aid Tools" panel forward. Select "Rebuild Database" and see, if it will resolve the the problem.
Good luck
Léonie

Issue with the recent MAC OSX 10.7.5 update

The recent MAC OSX 10.7.5 update rendered my WD external backup disk unusable. The iMAC only recognizes it as read-only now despite having 2 TB of available space. It doesn't even show on my desktop anymore. I have tried disk repair but it couldn't be repaired. Any suggestions?

Copy these commands into TextEdit, replace the bracketed part with your username and the quoted parts with the ext HD's name, retaining the quotes.
sudo chflags 0 /Volumes/"name of ext HD"
sudo chmod a+rx /Volumes/"name of ext HD"
sudo chown -R <your username w/o brackets>:admin /Volumes/"name of ext HD"
Launch the Terminal app in /Applications/Utilities, copy and paste the first one into the window that pops up, and hit the return key. When the Password: prompt pops up, carefully type in your admin password, since nothing shows on the screen, and hit the return key. Copy & paste the other two, one at a time, following each with hitting the return key. You won't get the password prompt, since the initial one's good for five minutes.
Quit the Terminal app and you should be able to read and write to the ext HD. This assumes there's no OS or Time Machine backup on the HD. If there is, don't run the third command.

HT1338 MAC OSX 10.4.11 update to run CS6

MAC OSX 10.4.11 update to run CS6 Photoshop, Illustrator and InDesign I have been told I may have to update to Lion - cheers Paul
Processor
2 x 3 Ghz Quad-Core Intel Xeon
Memory
3Gb 667 MHz DDR2 FB-DIMM
Hardware Overview:
Model Name:          Mac Pro
Model Identifier:          MacPro2,1
Processor Name:          Quad-Core Intel Xeon
Processor Speed:          3 GHz
Number Of Processors:          2
Total Number Of Cores:          8
L2 Cache (per processor):          8 MB
Memory:          3 GB
Bus Speed:          1.33 GHz
Boot ROM Version:          MP21.007F.B06
SMC Version:          1.15f3

Start by checking if you can run Snow Leopard:
Requirements for OS X 10.6 'Snow Leopard'
http://support.apple.com/kb/SP575
The OS 10.6 Snow Leopard install DVD is available for $19.99 from the Apple Store:
http://store.apple.com/us/product/MC573/mac-os-x-106-snow-leopard
and in the UK:
http://store.apple.com/uk/product/MC573/mac-os-x-106-snow-leopard
but nobody knows for how long it will be available.
When you have installed it, run Software Update to download and install the latest updates for Snow Leopard to bring it up to 10.6.8, or download the combo update from here:
http://support.apple.com/kb/DL1399
Check via Software Update whether further updates are required.
You should now see the App Store icon, and you now need to set up your account:
http://support.apple.com/kb/HT4479
To use iCloud you have to upgrade at least to Lion, but some functions are only available in Mountain Lion:
http://support.apple.com/kb/HT4759
You can also purchase the code to use to download Lion (Lion requires an Intel-based Mac with a Core 2 Duo, i3, i5, i7 or Xeon processor and 2GB of RAM, running the latest version of Snow Leopard), or you can purchase Mountain Lion from the App Store - if you can run that:
http://www.apple.com/osx/specs/

HT3775 How can i play my avi formatted movies with the new mac OSX 10.9.2 update?

How can i play my avi formatted movies with the new mac OSX 10.9.2 update?

Try using VLC or installing both QuickTime 7 and Perian. Nothing will work with all AVIs; some of them require codecs not available for Mac OS X.
(105507)

Mac OSX very Slow after update iLife

Dear all;
I just faced problem with my Mac OSX 10.8.4 after upgrade the iLife, the OS freeze then logout from the system
any ideas how to solve this problem?
Regards;

Please read this whole message before doing anything.
This procedure is a diagnostic test. It’s unlikely to solve your problem. Don’t be disappointed when you find that nothing has changed after you complete it.
The purpose of the test is to determine whether the problem is caused by third-party software that loads automatically at startup or login, or by a peripheral device.
Disconnect all wired peripherals except those needed for the test, and remove all aftermarket expansion cards. Boot in safe mode and log in to the account with the problem. Note: If FileVault is enabled, or if a firmware password is set, or if the boot volume is a software RAID, you can’t do this. Ask for further instructions.
Safe mode is much slower to boot and run than normal, and some things won’t work at all, including sound output andWi-Fi on certain iMacs. The next normal boot may also be somewhat slow.
The login screen appears even if you usually log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin. Test while in safe mode. Same problem? After testing, reboot as usual (i.e., not in safe mode) and verify that you still have the problem. Post the results of the test.

Mac OS 10.7.5 update fails on Macbook

Trying to update to 10.7.5 from 10.7.4 fails on about three different Macbooks I have.
I have tried through Software Update.
I have tried downloading the update from apple.com/downloads
I have tried downloading the combo update from apple.com/downloads
I have tried formatting the drive and reinstalling Lion and then repeating all of the above.
They all fail.
The most useful output I could get from it was using the installer command:
bash-3.2# installer -pkg ./MacOSXUpdCombo10.7.5.pkg -tgt /
installer: Package name is Mac OS X Update Combined
installer: Upgrading at base path /
2013-01-30 21:37:49.948 installer[612:7803] PackageKit: Missing bundle path, skipping: <bundle id="com.apple.airport.airportutility"></bundle>
2013-01-30 21:37:49.955 installer[612:7803] PackageKit: Missing bundle path, skipping: <bundle id="com.apple.PodcastCapture"></bundle>
2013-01-30 21:37:49.985 installer[612:7803] PackageKit: Missing bundle path, skipping: <bundle id="com.apple.NetworkUtility"></bundle>
2013-01-30 21:37:50.029 installer[612:7803] PackageKit: Missing bundle path, skipping: <bundle id="com.apple.XsanAdmin"></bundle>
installer: The upgrade failed (The Installer encountered an error that caused the installation to fail. Contact the software manufacturer for assistance.)
The missing bundles don't necessarily surprise me since they sound like fairly specialized applications. There seems to be no other indication of WHY it failed however, and no contact information to find out what to do next.
Help? This is affecting about 5 Macbooks that I have tested so far, so probably another 15 that I haven't tested yet.

After researching older questions and answers it came down to the battery. Sure enough my battery was warped on the inside and the outside. The inside warp presses on the underside of the trackpad and click bar causing all sorts of misadventure with the trackpad and click bar. So I answered my own questions.

Mac OSX 10.4.8 Update Breaks Raid Striping -- System will no longer boot

Hi,
I'm a newbie from the PC world with a Mac Pro. For the last 8 hours I've been trying to get a Raid-0 configuration to work with no success.
The Raid array constructs ok and the system boots. Once that's done the Software Update screen arrives and I would select install all... then the machine would not boot. I get a Grey Shade like affect and the message to power off and restart. Powering off does nothing.
So I started again for the Nth time and added each Software Update individually. All loaded and rebooted successfully until the 10.4.8 Update.
As soon as that loads, installs and restarts the machine will not boot.
I called Apple's Tech Support and they told me they do NOT support RAID on this machine. I said what are you talking about. They put me on hold talked to a supervisor and came back with the same story. I just don't get it...
So anyone have any insight and advice on why the update breaks my Raid-0? What can I do to get over the problem (I'd like to have the RAID...)?
Thanks for the assistance.
Mac Pro Mac OS X (10.4.8)

Yes, you needed an emergency boot drive anyway to repair your RAID boot drive. Just use the same one in addition to a working clone or backup of your regular system.
Apple made it easy to install or update security updates and system updates from an alternate drive (but you will have to use the stand-alone (combo preferably) updaters instead - which many use already as normal part of upgrades for years now (they seem more useful and reliable).
My preference is a dedicated boot drive with OS and apps and minimal home directory - no media files - and fast, like 10K Raptor. I use RAID for my home directory so it isn't on the boot drive for years to improve performance and keep the OS separate. Never a problem and nice mix.

Firefox 3.6.15 is not downloading on MAC OSX, not via software update nor via manual download. It claims i do not have full admin rights which is not true.

If I do a manual download via FF website, it starts to install, asking if I want to replace an older version of FF. If I then continue, it says that it cannot process as I do not have access to 'certain components'????
I have full admin rights, it is f... my computer. I am running a Macbook Pro on OSX 10.6.6.
FF is giving me more problems lately, a.o. not showing certain flash elements (have latets flashplayer). Anyone else getting annoyed with FF?

I eventually did an archive and install to get 10.4.7 installed on my MBP the last time around. Now 10.4.8 is doing the same thing. Neither via Software Update nor manual downloads of Intel delta or combo updaters will apply. Arg!
Has anyone else seeen this? I've tried applying the update while booted regularly and also in safe boot to no avail.
Mike

Dreamweaver CS6 crashes after Mac OSX 10.9.3 update.

Updated today to Dreamweaver CC, and the issue persists. My 'local' files are stored on a Windows Vista server on the LAN.
Everything worked OK until 2 days ago, so I'm almost sure the issue is related to the OS update.
I can open a file, work on it for a while, and after a few minutes, Dreamweaver 'hangs' and can take up to 10 minutes to be responsive again.

You will probably get better help in Dreamweaver support forum
EXCEPT... there are LOTS of messages concerning 10.9.3 so read below
Mac 10.9.3 workaround https://forums.adobe.com/thread/1489922
Mac 10.9.3 and CS6 https://forums.adobe.com/thread/1480238
Enable Mac Root User https://forums.adobe.com/thread/1156604
-more Root User http://forums.adobe.com/thread/879931
-and more root user http://forums.adobe.com/thread/940869?tstart=0
The Cloud forum is not about using individual programs
The Cloud forum is about the Cloud as a delivery & install process
If you will start at the Forums Index https://forums.adobe.com/welcome
You will be able to select a forum for the specific Adobe product(s) you use
Click the "down arrow" symbol on the right (where it says All communities) to open the drop down list and scroll

Dreamweaver CS6 / CC crashes after Mac OSX 10.9.3 update.

Updated today to Dreamweaver CC, and the issue persists. My 'local' files are stored on a Windows Vista server on the LAN.
Everything worked OK until 2 days ago, so I'm almost sure the issue is related to the OS update.
I can open a file, work on it for a while, and after a few minutes, Dreamweaver 'hangs' and can take up to 10 minutes to be responsive again.

Hi Rudolfo,
Welcome to Adobe forums. See Prompted to install Java SE 6 Runtime | Mac OS 10.9 and Unresponsive on Mac OS 10.9. If you sill have problems, reach out to me over a private message providing your Adobe ID, location, and contact details (email ID, phone number).
Thanks,
Preran

Mac OSX 10.8.3 update problem

Ok, so I followed through with the OSX update (I have mountain lion) and let it do it's thing - came back to it hours later......STILL in the apple screen with rotating gear wheel thing....so I shut it down, power off. Then I restart it, it comes up with the same screen, this time with a grey progress bar.....and then 20 seconds later it shuts itself off. Now everytime I turn it on, it ends up shutting itself off....WHAT?! Anyone else having a similar or the same issue?! I'm so frusterated....anyone, help?? >_<

Ok, so I followed through with the OSX update (I have mountain lion) and let it do it's thing - came back to it hours later......STILL in the apple screen with rotating gear wheel thing....so I shut it down, power off. Then I restart it, it comes up with the same screen, this time with a grey progress bar.....and then 20 seconds later it shuts itself off. Now everytime I turn it on, it ends up shutting itself off....WHAT?! Anyone else having a similar or the same issue?! I'm so frusterated....anyone, help?? >_<

Mac OSX 10.7.5 update failed to save?

Similar Messages

Maybe you are looking for