Mac OSX will not boot, when I log in, it shuts down after grey screen and grey loading bar show up: PLEASE HELP (:

So here is a lowdown on my problem.
I start my mac OSX, I hold down the alt/option key and load my MAC osx drive (which is the only drive available; however, when i do not hold down the alt/option key it will go to a black screen that says "no bootable device, press a key when device inserted").  Continuing, it then goes to my login screen where I have my username, and I can enter my password like usual.  I enter my password, hit the enter button (like I always do), and this is where my problem begins.
After I enter my login and hit enter, the screen goes grey, with a little apple symbol in the middle and a different shade of grey loading bar underneath.  This grey loading bar shows up for about 10 seconds, fills up about 10-20 percent, and then shuts my computer down. 
No matter what I do, this process repeats over and over, and heres where the problem gets worse, and this part is VERY IMPORTANT and is the most depressing, stressful part of the process.
NONE of the startup/boot commands work except holding the alt/option key.  I can't hold: Command plus r; command pr  to reset PRAM; shift to enter safe mode.
I really dont know what to do here :/.  I have files that I want on the hard drive, that are pretty important but not critical.  I gave up on wanting the files back but now I want to simply WIPE my computer and re-install a clean version of OSX onto the computer, but I CANNOT GET TO THE REINSTALLER :(.
More information that may be helpful:
          I do have a partition on the HDD that I was going to use for Bootcamp, but it does not have anything installed on it (thus causing the "no bootable device" screen to load, and probably causing the boot commands not to work).
          My version of Mac OSX is 10.8.4. "MBP 15.4/2.8/16GB/768 flash"
          The last time I restarted my computer, my mac OSX RAM was down to 1.75 GB, with nothing open.  Usually when nothing is open the free RAM is around 10-13 GB (I know this because I have the activity monitor always open, and I use my computer a lot).
          Again, boot commands will not work, except for holding the alt/option key.
So if anyone can help me fix my problem(s), which are:
1: using boot commands; 2: reinstalling mac OSX; or 3: getting my files,
I would love you forever.  I would really prefer 1 or 2.  Thanks for reading this.

Oh and one more thing, I do not have a disc drive in the mac osx.  The version I have comes without one.
I am very puzzled about what to do right now.

Similar Messages

  • Satellite M40X-169 when connected to wireless unit shuts down with blue screen and restarts

    Hello.
    I got the problem with my notebook when i'm connecting and getting connected to the wireless network. My notebook is shutting down with blue screen error and then restarts.
    Maybe you can help me to solve this problem, because i can normaly work when i need to be connected.
    Plaese help me.

    Hi
    It is not easy to give you some precise answer but try to remove WLAN card from device manager and restart the unit. You can also check Toshiba download page and try to install the latest WLAN card driver.

  • I have a new mac pro.  i may have changed the settings and now when i log on it shuts off after 10 seconds. not long enough to check settings.

    i am new to mac book pro.  i was checking out the settings and must have changed something as now when i log on, it shuts down within 10 seconds and i don't have time to get into the settings. the top tool bar is red/pink.  please help!

    Close all windows and quit all applications.
    Hold the option key down and click the "Go" menu in the Finder menubar.
    Select "Library" from the dropdown, then "Preferences" folder.
    Look for these two files.
    com.apple.desktop.plist
    com.apple.systempreferences.plist
    Right click each  one of those and select " Move To Trash" from the contextual menu.
    Restart the computer.

  • Will not boot up to log in screen

    will not boot up to log in screen when powered up, all I get is a grey screen with apple logo in middle and spinning timer
    I have tried resetting SMC
    I have tried starting up in Safe Mode (it won't do that either)
    I have gotten into disk utility to repair disk
    I have tried resetting PRAM
    nothing... we are on a network in a school district so my next step is to re-image it but wondering if there is something else I should try first
    if not then how do I backup files that are needed before I re-image
    thanks, Cindy

    Take each of these steps that you haven't already tried. Stop when the problem is resolved.
    Step 1
    The first step in dealing with a startup failure is to secure the data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since the last backup, you can skip this step.   
    There are several ways to back up a Mac that is unable to start. You need an external hard drive to hold the backup data.
         a. Start up from the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.” The article refers to starting up from a DVD, but the procedure in Recovery mode is the same. You don't need a DVD if you're running OS X 10.7 or later.
    b. If Step 1a fails because of disk errors, and no other Mac is available, then you may be able to salvage some of your files by copying them in the Finder. If you already have an external drive with OS X installed, start up from it. Otherwise, if you have Internet access, follow the instructions on this page to prepare the external drive and install OS X on it. You'll use the Recovery installer, rather than downloading it from the App Store.
    c. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, start the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
    d. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
    Step 2
    If the startup process stops at a blank gray screen with no Apple logo or spinning "daisy wheel," then the startup volume may be full. If you had previously seen warnings of low disk space, this is almost certainly the case. You might be able to start up in safe mode even though you can't start up normally. Otherwise, start up from an external drive, or else use the technique in Step 1b, 1c, or 1d to mount the internal drive and delete some files. According to Apple documentation, you need at least 9 GB of available space on the startup volume (as shown in the Finder Info window) for normal operation.
    Step 3
    Sometimes a startup failure can be resolved by resetting the NVRAM.
    Step 4
    If you use a wireless keyboard, trackpad, or mouse, replace or recharge the batteries. The battery level shown in the Bluetooth menu item may not be accurate.
    Step 5
    If there's a built-in optical drive, a disc may be stuck in it. Follow these instructions to eject it.
    Step 6
    Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to start up, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can start up now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
    Step 7
    If you've started from an external storage device, make sure that the internal startup volume is selected in the Startup Disk pane of System Preferences.
    Start up in safe mode. Note: If FileVault is enabled, or if a firmware password is set, or if the startup volume is a Fusion Drive or a software RAID, you can’t do this. Post for further instructions.
    Safe mode is much slower to start and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
    The login screen appears even if you usually log in automatically. You must know the login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
    When you start up in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, the startup volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 11. If you ever have another problem with the drive, replace it immediately.
    If you can start and log in in safe mode, empty the Trash, and then open the Finder Info window on the startup volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then restart as usual (i.e., not in safe mode.)
    If the startup process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
    Step 8
    Launch Disk Utility in Recovery mode (see Step 1.) Select the startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
    This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then restart as usual.
    Step 9
    If the startup device is an aftermarket SSD, it may need a firmware update and/or a forced "garbage collection." Instructions for doing this with a Crucial-branded SSD were posted here. Some of those instructions may apply to other brands of SSD, but you should check with the vendor's tech support.   
    Step 10
    Reinstall the OS. If the Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
    Step 11
    Do as in Step 9, but this time erase the startup volume in Disk Utility before installing. The system should automatically restart into the Setup Assistant. Follow the prompts to transfer the data from a Time Machine or other backup.
    Step 12
    This step applies only to models that have a logic-board ("PRAM") battery: all Mac Pro's and some others (not current models.) Both desktop and portable Macs used to have such a battery. The logic-board battery, if there is one, is separate from the main battery of a portable. A dead logic-board battery can cause a startup failure. Typically the failure will be preceded by loss of the settings for the startup disk and system clock. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
    Step 13
    If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store, or go to another authorized service provider.

  • Hello, mac mini will not boot. I get a file symbol with a question mark, then a white screen, Hello, mac mini will not boot. I get a file symbol with a question mark, then a white screen

    Hello, My mac mini will not boot. When I turn it on, I get the chime, then the white screen, then the apple symbol, then a file symbol with a question mark, then the white screen and then it stays like that.
    Is this a bad hard drive?

    Sounds like it.  Try booting from your OSX restore DVDs - startup and hold down "C".  This will take AGES! Then run Disk Utility from the menu. 
    The flashing ? means your system is corrupt, dead, not there, on a dying HD, etc...

  • 2009 Mac Pro will not boot up under Windows

    I have an Early 2009 Mac Pro system (Mac Pro 4,1) and I've had this system for 3 years already and have been working under OS X with this system ever since I purchased it.
    However, when I tried to boot off my Windows disk, something very interesting happens. The Mac Pro WILL NOT boot up off the Windows disk or a known working Windows partition if two monitors are connected. Upon holding down the option key and selecting the Windows partition, I will get a black screen on one monitor (the one connected via Mini Displayport) and the other screen receives no signal and will enter standby and the system is halted. It does not respond to keystrokes, there is no hard drive activity, no measured power increase on the UPS, no apparent network activity, nothing. The only way to exit this scenario (from what I can tell) is to power off the machine, disconnect the display on DVI, power on the machine again, select the Windows partition wait for the system to reach the login window and reconnect the DVI monitor (at which time Windows recognizes it immediately and the system works fine again).
    My question to the community is, does anybody know why this is happening and is there a known fix for this? Quite frankly, having to disconnect a monitor just to restart is very tedious and frustrating. 
    I have two Samsung P2350 monitors attached to an ATI Radeon HD 4870 (512MB, from Apple). One is monitor is connected via directly DVI and the other is using a Mini Displayport to DVI adapter. Both monitors work fine under OS X with no issue. At first, I thought that this may be a driver issue on the Windows side and after installing all the latest updates and drivers the issue is still apparent. From what I can tell, this doesn't seem like a software issue but rather a firmware or EFI issue as this happens before Windows even loads.
    If anyone knows of a fix or what to do in this situation, or if you are also having this issue, I would love to hear your input!
    Thank you!
    For the record, I am running all the latest software builds on the OS X side (10.7.4, not that it would really matter at this point). I have also disconnected all unnecessary equipment in a trial and error scenario but the results are still the same.
    The system passes all ASD testing.
    The full specification of the computer and all connected equipment are as follows:
    2009 Mac Pro (4,1) 8-Core
    2x Intel Xeon Nehalem 2.66GHz Quad-Core CPUs
    16GB DDR3 ECC 1066MHz RAM (Apple Branded)
    Two OWC 120GB SSDs (One for OS X, the other for Windows 7 x64) - These are in place of my optical drives.
    4x 2TB WD Black Hard drives for storage.
    Two Samsung P2350 Monitors connected via DVI. (One using a Mini Displayport to DVI adapter).

    In Windows I am using the latest (12.4) Catalyst Software Suite, 64 bit of course, downloaded directly from AMD's site after installing the drivers from Boot Camp.
    As for installing Windows I used an original (not burned) installation media (Disk is in a pristine condition). And yes, Windows is fine, the problem just seems to be getting the system to boot up Windows with that second monitor. However if the "problem monitor" is disconnected the system boots fine 100% of the time and connecting it later after booting the system will still operate properly.
    For the sake of arguement I swapped monitor cables and connected the "second" monitor to the mini displayport adapter to verify that it wasn't a cabling issue and I'm still yielding the same issues.
    As for GPU testing, I've played games (Crysis, Grand Theft Auto IV, Battlefield 3, etc.) and I've had no issues with the card or stability.
    You would think that Apple would try to find a fix for this, especially considering the caliber of this machine.

  • Replaced Optical Drive now Mac book will not boot up

    I bought a second hand Mac Book Pro A1150 model.  It did not have an optical drive so I bought one, installed it and now my Mac Book will not boot up.  When I take the drive out the Mac Book boots up fine.  I was told that the optical drive although used was tested and work when it was shipped out.  I'm a little new to Macs but not new to working on computers.  Is it common for a possible defective optical drive to casue a Mac Book pr to not boot up or does this sound like an issue with the optical drive cable, or possibly the logic board?

    That is true.  I cannot think of any way to test the Optical Drive without swapping it into a known correctly operating MBP.
    A thought which probably may not be an issue.  When I installed an Optical Drive in my old (2006) MBP, I remember seeing in the instruction manual an item called a grounding pad (which looked like a tiny steel brillo pad with out soap) which was missing in mine.  The MBP worked and I essentially ignored it.  Perhaps that may not be case with your situation.
    My thoughts are that the Optical Drive is malfunctioning and the cause of your problem.  Perhaps you should consider getting a new replacement from OWC.  But that entails a $100 risk with no guarantees of success.
    Ciao.

  • 210-4125 will not boot when windows 7 x64 is installed

    i have posted this problem a while ago "210-4125 will not boot when windows 7 x64 is installed"
    hoping that some one new might have had the same problem
    HP.......................................HP MINI PC  210-4125
    model ................................210-4125
    Bios ...................................F08
    ser no................................ [edited Serial Number by Moderator]
    product no.........................A8V56EA#ABU
    Ram ..................................4.0 GB
    system board ID............... 338d
    processor .........................Atom(TM) CPU N2800 1.86GHz
    Product configuration ID..0797200000204600000300100
    acording to INTEL the cpu is X64 bit, but the bios will not let a X64 boot up only a x32 bit ?
    and i get a message on black screen  "you are trying to load an opperating system not compatable" or some thing like that
    it would seem that the bios is the problem and not the CPU ? the 08 bios update only covers x32 bit and not x64
    if any one out there is running x64 bit windows 7 on the 210-400 range of netbook   can you tel me
    1. model no
    2.CPU
    3.Ram installed
    4 bios No
    thank you
    JB

    thank you George
    i will bear that in mind next time
    i see that you work for HP ? do you have any suggestion's for my problem ?
    as i mentioned before the notebook works faultlessly when X64 windows 7 is installed via the OEM disk in the external DVD drive , but if i disconnect the DVD drive it will not boot, but gets stuck in boot loop , then if i connect the drive with any windows installation disc loaded in it , it loads perfect and works perfect even if i disconnect when loaded  , but i can not keep the drive connected ?
    i have tried to use a USB flash drive to install X64 windows 7 but it comes back that the present CPU is not compatible ??
    when it clearly states on Intel web site that it is and it works perfect when loaded ?? even the Windows update manager confirms that it will run all X64 windows OS
    i understand the the bios "InsydeH20" is a very difficult bios to work with, and that Insyde have blocked the "hidden menu" via software ? i have exhausted all the software functions to open the complete bios that i can find at the moment  ,  i think it is locked out from out side the bios and not from inside.?
    any  pointers in the right direction would be very helpful  ,
    many thanks
    John

  • Mac Mini will not boot OS, can I get to files with another Mac?

    My mac mini will not boot the OS proserly, it goes to a screen that tells me that some root folder can not be found.
    The install CD works and I can boot to it. The disk utility reports no problems, all disk repairs done and OK.
    The computer still will not boot to the OS.
    How can I get the files I need off the drive before I reinstall the OS?
    I have other Macs and fire wire cables, cross over cables, regular eithernet cables. What can I do?
    Thanks!

    How can I get the files I need off the drive before I reinstall the OS?
    Connect it to another Mac with a FireWire cable and start it up with the T key held down.
    (40535)

  • My Mac pro will not boot. it gets stuck on the grey screen.

    My Mac pro will not boot. it gets stuck on the grey screen. What can I do?

    Mac OS X: Gray screen appears during startup
    If using 10.7 or later, the Installer/Utilities DVD has been replaced with a special emergency partition on the Hard drive called "Recovery_HD"

  • W520 will not boot when docked; blue screen

    W520 fails to boot 100% of the time when docked. Blue screen shows SYSTEM_SERVICE_EXCEPTION, STOP x0000003B for nvlddmkm.sys
    nvlddmkm.sys is the NVIDIA driver, which is version 8.17.12.9620, the latest shown on the NVIDIA and Lenovo websites. BIOS is also the latest.
    Systems boots fine if I remove it from the dock, but it will not boot when docked.
    Windows 7 PRO SP1
    2 external monitors via DVI
    Any suggestions?

    Boot with Option held down. After the cursor changes to an arrow, Command-. (Command Period) should open and close the optical drive. After you insert the disc, click the curved arrow to have it re-scan the discs for boot volumes. Then select the optical drive and click the straight right-pointing arrow to start.
    Try it with the Apple Hardware Test disc first and run Extended Tests.

  • ITunes quits when I'm trying to open it. I have installed the latest version and another user on the same Mac can use their iTunes when they log in. I have tried deleting iTunes and re-installing but it still won't open. Any ideas?

    iTunes quits when I'm trying to open it. I have installed the latest version and another user on the same Mac can use their iTunes when they log in. I have tried deleting iTunes and re-installing but it still won't open. Any ideas? Thanks.

    Hold down the option key while starting iTunes and make an new library.  Will it open then? If so, you have a bad library.  With the new library import the library.xml version of the file in your iTunes folder.  This will make it 90% like before (some metadata are not identical, but I don't know which ones).
    iTunes: How to re-create your iTunes library and playlists - http://support.apple.com/kb/ht1451

  • Hello. Please help. for unknow reasons, I am not getting any of my mail on anything, nothing on my iphone, my outlook or even when I log into icloud online ???   any one else having troble??   please help   I need my mail

    Hello. Please help. for unknow reasons, I am not getting any of my mail on anything, nothing on my iphone, my outlook or even when I log into icloud online>???
    any one else having troble??
    please help
    I need my mail

    Hello, DragonStudios. 
    Thank you for visiting Apple Support Communities.
    Here are a couple troubleshooting resources I would recommend when experiencing issues with iCloud Mail.
    iCloud: Troubleshooting iCloud Mail
    http://support.apple.com/kb/TS4002
    iCloud: Account troubleshooting
    http://support.apple.com/kb/TS3988
    Cheers,
    Jason H.

  • Autoplay window will not open when I connect Iphone 6 plus with Ver 8.1 and running windows 8.1 on pc.

    Autoplay window will not open when I connect Iphone 6 plus with Ver 8.1 and running windows 8.1 on pc.

    Hi, sstroec,
    How about your problem now? Is arnavsharma's suggestion helpful? If you need any further assistance, please feel free let us know.
    Roger Lu
    TechNet Community Support

  • My iPhone will not charge when I plug it first, I have to unplug it and when I plug it again, then it charges

    My iPhone 4 (GSM) will not charge when I plug it first, I have to unplug it and when I plug it again, then it charges... It is very weird... Has this happened to anyone?
    Thank you in advance for the answer.

    It is yet happening to me. In my case it happens when I plug it to any kind of charger: socket, car... I have to pull it out the phone and plug it in again so it reacts and starts charging.
    Of course, I tried cleaning with a soft, dry brush. This had no effect.
    Thanks again and best regards.

Maybe you are looking for