Mac Pro 1,1 Ati X1900xt black screen on cold boots

I am having trouble with my video on cold boots. The video does not respond when directly booting into OS X but I can boot into bootcamp blindly and then I can restart into OS X. Kinda a back door entrance to OS X. I cannot tell if it is the Video Card (ATI x1900xt) or if it is in the Monitor as they both work under windows then back into OS X. As soon as I shut down, everything goes black sceen and I get no video input. I have tried three brand new different adapter from DVI-d to VGA on the computer all of them do the same thing. If there is ANYONE that might be able to shed some light on this, PLEASE HELP!!!!
Here is Everything I have tried...
1. nvram reset - done
2. SMC reset - done
3. pulled all ram and video card out - done.
4. pulled all extra drives out - done.
5. re installed OS X - Done.
6. checked DIAG-TEST - all LED's respond normally.
7. tried talking to the "genius techie" at MAC store to no avail - he was completely useless.
Thanks in advance.

This is now a three week plus old question.
There are tips on video cards like this:
http://www.xlr8yourmac.com/
To pull the card every 3-4 months to remove dust clogging the card's air chamber;
To boost system 3 of 4 fans to improve cooling and air flow.
Problems with that card and WoW have been around since early days on WoW forum.
And that there is a recall for some of the Mac Pro X1900s, also found on above web site.
AT this point in time, I'd skip ebay for ATI 5770 as long as you run 10.6.5 as you won't be able to boot anything lower than 10.6.4, so you need some good bootable backup strategy and more.
I have the 8800GT 1st gen (from Apple) $279 though there are/were tips on flashing too.
And ebay 'macvideo' or something has had 8800s if you want to go that route.

Similar Messages

My Mac Pro Freeze or just go black screen when i squeeze the might mouse,

At the side, and some times i seems to see black lines about two across the screen, could this be my Graphic card acting up or could it be a faulty hard drive as at one time i could hear a spinning which sounded like the H.D was going mad.
But after i reboot its okay until i squeeze the mouse again it happens sometimes.
X1900 is my Graphic-Card.
Fr.BlayZay.

Hi NOTHING SPECIAL, and a warm welcome to the forums!
How much free space is on the Hard Drive?
Have you done any OS or Disk Maintenance?
At this point I think you should get Applejack...
http://www.versiontracker.com/dyn/moreinfo/macosx/19596
After installing, reboot holding down CMD+s, (+s), then when the DOS like prompt shows, type in...
applejack AUTO
Then let it do all 5 of it's things.
At least it'll eliminate some questions if it doesn't fix it.
The 5 things it does are...
Correct any Disk problems.
Repair Permissions.
Clear out Cache Files.
Repair/check several plist files.
Dump the VM files for a fresh start.
See if it does better then after a restart or two.

My macbook wont come on. black screen saying insert boot disc please help

Just tried to turn on my mac book. came up with a black screen and insert boot disc. never done this before. cant find my serial number on the mac book so cant find the support i need. please help

Mandalizabeth39 wrote:
thank you that worked great
You never answered my question, and if you have not changed anything then this will happen again
What choices were presented by the boot manager

Mac book pro won't turn on black screen and capslock key on

Macbook pro won't turn on - black screen and caps lock light is on

Hi Daleobrien73,
Welcome to Apple Support Communities.
You may find some useful suggestions for troubleshooting your MacBook Pro in these articles:
Apple computers: Troubleshooting issues with video on internal or external displays
http://support.apple.com/kb/HT1573
Troubleshooting: My computer won't turn on
http://support.apple.com/kb/ts1367
Best,
Jeremy

I have a 30 inch monitor on my mac pro tower that just went black, what do I do to fix it?

I have a 30 inch monitor on my mac pro tower that just went black, how can I get it back on?

He's asking what are those things you are using, i.e., ...
What video card are you using?
What version of OSX are you using?
What model of mac pro are you using (e.g., 2010 Mac Pro is 5,1).
And also,
Try smc and pram reset.
And see if the monitor lites up if you boot in safe mode.
It is possible your monitor simply failed -- its power supply or something else.

Hi...m using a mac pro quad core.....its not booting up...i can only see the apple logo and a circle loading...could not get into the login screen

hi...m using a mac pro quad core.....its not booting up...i can only see the apple logo and a circle loading...could not get into the login screen...any suggestions please.....m in the middle of a project and now i have got this one
regards,
v.s.bharan

Welcome to Apple Discussions!
Do you keep your data backed up?
If not, you should always do so*:
http://www.macmaps.com/backup.html
You never know when a hard drive or a directory might go bad. Having a bootable clone is a must.
That link also shows you some tools you can use to recover data.
If you aren't backed up, try buying those tools first, before attempting to repair the directory.
Directory issues can be fixed with these tools*:
http://www.macmaps.com/directoryfaq.html

Is FCPX usable with late 2007 Mac Pro's with ATI HD3870 (or OEM graphics cards?

I have a late 2007 Mac Pro with an ATI Radeon HD3870 Mac&PC (3870 ROHS 512mB) graphics card. This card is wupposed to be OpenCL hardware capable. Will it work with FCPX? I'm not aware of any current enhanced graphics cards that will work with that vintage MacPro. I'm currently using FCP7, but has anyone tried this system with FCPX?

nfoo wrote:
According to Apple it is compatible.
Just go ahead and try to buy it: the App Store will detect if your card is compatible and will refuse to let you buy FCPX if it isn't. So there's no risk.
If you want to upgrade your gfx card, the Ati 5770 and 5870 are both compatible with all Mac Pro Models.
Apple says no. The Store says mid 2010 for 5770.
I just got confirmation from someone on the LAFCPUG forum that they have MacPro 1.1 (2006) with 5770 installed and they were able to purchase FCPX.

I bought my Mac Air 13' in August. Black screen problems constantly happens. I asked some of my friends who also use Air. They share the same experience. Overall, it is a pretty good computer. But it bothers me when I do work and it suddenly goes black.

I bought my Mac Air 13' in August. Black screen problems constantly happens. I asked some of my friends who also use Air. They share the same experience. Overall, it is a pretty good computer. But it bothers me when I do work and it suddenly goes black. What should I do about it?

without more information, I assume you mean a blackout from sleep issue.
Go to system preferences > energy settings > raise the "turn display off" setting up to as needed, say 5 mins. or 10 mins.
AND ...
unchecked the "Put hard disks to sleep when possible" in both the battery and power adapter tabs.
test it and check back

I opened my MacBook Pro to a dark gray/black screen. Rebooted several times to no success. Pressed the "sunrise" button to no success. Computer only 14 months old. Any suggestions to get this puppy working?

I opened my MacBook Pro to a dark gray/black screen. Rebooted several times with no success. Pressed the "sunrise" key several times with no success. Any suggestions to fix this?

Do you have AppleCare? Even if you don't, take to the Apple store and tell them what happened. They should help even though it's a few months out of warranty. You might have to talk to a manager or different higher up.

I currently run Mac Pro with three hard drives. Can I dual boot or even triple boot with Snow Leaopard on one drive and Mountain Lion or Lion on others?

I currently run Mac Pro with three hard drives. Can I dual boot or even triple boot with Snow Leopard on one drive and Mountain Lion or Lion on others?
I need to keep Snow Leopard so that I can run some old softward.

If you are careful you can put at least two on one drive, having Recovery from Lion and Mountain Lion on their own drives though.
CCC can clone Lion Recovery - great for moving or backup.

Mac Pro (ATI X1900) black screen at boot

Hey there,
I've been seeing some problems with my early Mac Pro when booting. Upon the first boot of the day, the machine sounds like it's starting up however the display remains black for upto 15 minutes before kicking in.
The problem used to happen occasionally but it's just been getting worse over the last 6 months.
It's got to the stage that if you put the machine into sleep mode, then come back 30 minutes later I'll have to wait for another 15 minutes before I can log back in.
If the machine has been running for a while and you perform a regular reboot, you can see the system booting and the login window comes up straight away.
I've tried a fresh install of Leopard on an external drive, problem still exists.
I also tried hooking up another display to the system just to check it wasn't the existing monitor and sure enough the problem remains.
Recently the display has been blanking for a few seconds when I've been using the system.
Searching to forums seems to suggest a whole bunch of issues with the ATI X1900 card, which is installed in this system.
Does anyone think the ATI card is the fault here?
In addition, I know the system is out of its initial years warranty but it seems like the ATI card has some known problems, so what's the likelyhood of Apple helping me out here?

You are chasing down the wrong rabbit hole is my best guess, as bad as the X1900 might be.
Rule out marginal RAM, Seagate drives, 3rd party USB/FW devices, controllers (other than X1900), even modem/router. All it takes is a bad USB or FW (or probably RJ45) cable.
No need to reinstall. Now that you have, clone your system for backup and testing with SuperDuper and run Disk Warrior, too, and try that. Might want to rerun the last combo update. And I always run the combo update from another drive than the system being updated.
SuperDuper forces the newly cloned system to rebuild all the temp files, logs, caches and such that are best done by itself when first booted.
Other things to try are reset the SMC RESET button on pre-2008 Mac Pro (on 2008 model, leave it unplugged overnight, no cables attached to clear or reset the SMC) and then zap NVRAM on cold boot.
See this article:
http://www.macfixit.com/article.php?story=20060131080021235

Monitor goes dark on 2008 Mac Pro Tower with ATI Radeon 5870 Card

I have a 2008 Quad Core Intel Mac Pro Tower running 10.6.8.
The original graphics card had trouble with HD movies of any kind and eventually my screen would sometimes not turn on (stayed black) when the computer was turned on.
So I replaced the graphics card for both reasons to a ATI Radeon 5870 PCIe with a GB rather than the 256 that came with the machine.
The problem was solved. I got a new monitor, one that is like the latest ones and all has been working great for a few years.
Then recently the monitor started going dark while the computer was on. (no screen saver or anything like that, I can be in the middle of work on a photo or video).
Trouble shooting I have tried.
A forum said drag the mouse to the hot corner for a while and then back. Well, I tried, assuming I was dragging the mouse to the corner. Didn't work.
I tried using the keyboard commands to shut down the computer. It didn't work.
I tried plugging the keyboard into other USB ports and tried to shut down the computer. No luck.
The only thing that works is shutting down the computer with the power button.
on start up the monitor is back on.
Sometimes it works for days like this, other times the monitor stays on only minutes.
The monitor is fine. Tested my old monitor on the computer to make sure it wasn't my new monitor.
So the questions are:
Can it be over heating?
is it worn out, toast, done and or dead and dieing?
Should I buy a replacement graphics card VS finally upgrading and getting a new computer (lots of $$$$ but then I do work in HD Video so....)
any help is appreciated
thanks
john

Replacing FBDIMMs would be today inexpensive and worth doing.
No one knows if heat is an issue without your using thermal sensor monitor. Probably want to up the default fan speeds while at it.
And because you don't have Lion+ then even more reason to setup a small maintenace volume on another drive with OS X basic system for repairs. In fact you should always have a bootable backup or two you can rely on.
Restarting may work, or it may be you have now new issue with corrupt fies or directory that a safe boot even is no guarantee of fixing.
When in doubt, try a clean new OS install on another drive.
And FBDIMMs: $25 for a 2x2GB set on Amazon.com
You want to get the most out of what you have, a small investment in RAM, maybe recycle those drives for 2-4TB units. And an SSD will have system responding better and perform better.
My guess, the 5870 wasn't needed and was overkill and a 5770 for almost half would have been more than adequate.

When I boot up my Mac Pro, I get a small black puzzle looking piece on the lower right side of my thunderbolt

Brand new Mac Pro, 2 thunderbolt monitors;
I get a small black puzzle looking piece on the lower right side of my 1st thunderbolt monitor when I boot up. It goes away once the computer fully boots, it is only on there for a second or so. Does anyone have a similar issue?
These are only 1 month old.

It has been seen before, when hardware was malfunctioning:
Re: hello, I turn on my mac and I see a figure over the right part of the screen, do anybody knows what is that?
Re: bootup symbol

MacBook Pro Locks up w/ unresponsive Black Screen, Stuttering sound.

Hello,
Having searched high and low, I can't seem to find a solution to my predicament.
I have a Mid-2010 15" i5 MacBook Pro, and when I run programs that kick my GPU onto the nVidia card, I will randomly get a completely black screen. This is not apparently the more common "black screen of doom" because I cannot do anything at all to the computer - I see no mouse pointer, I can't adjust the screen intensity, and the only resolution is to force shutdown and reboot. My sound also loops the last second or so of audio if anything was playing at that time, and the force shutdown produces a audible 'pop' most times, which sounds like it might be from the HD. When I do so I get a message about Mac OS X unexpectedly crashing, and a check of the Console seems to indicate that it's some sort of kernel panic. I've reset PRAM, SMC, etc and run all the normal disk checks and nothing has come up. It's only been repeatable when I put the computer to sleep, then log back in, and log into a Minecraft server. It has happened on other occasions randomly, such as when Safari had chewed up a great deal of RAM, or during when I was playing Oolite. It would appear, judging by the amount of time each one of these instances takes, that it's something to do with RAM usage possibly, but the kernel log indicates something might be awry on the nVidia card side of things.
Here's the log. I'm really at a loss here, and this is quite annoying to keep losing my work when I happen to absentmindedly open a game up after a long session of writing, etc. I'm afraid that ultimately I'm going to have to take it into the shop, but as a college student with no nearby Apple store, I just can't afford to not have it with me - I'm using it constantly for my work.
Interval Since Last Panic Report: 16181 sec
Panics Since Last Report: 2
Anonymous UUID: AB5E6E2A-652F-452D-BC74-386B74C54957
Sun Feb 13 20:50:44 2011
panic(cpu 0 caller 0x9f8bfa): NVRM[0/1:0:0]: Read Error 0x00000100: CFG 0x0a2910de 0x00100000 0x00000000, BAR0 0xc0000000 0x7ee1c000 0x0a5480a2, D0, P3/4
Backtrace (CPU 0), Frame : Return Address (4 potential args on stack)
0x92e13888 : 0x21b50c (0x5d4438 0x92e138bc 0x223974 0x0)
0x92e138d8 : 0x9f8bfa (0xc0e2bc 0xc7e940 0xc1d424 0x0)
0x92e13978 : 0xb13640 (0x9acd404 0x85aa004 0x100 0x86)
0x92e139c8 : 0xb0a639 (0x85aa004 0x100 0x92e139f8 0x9e86d7)
0x92e139f8 : 0x171b9ce (0x85aa004 0x100 0x438004ee 0x5508e0)
0x92e13b38 : 0xb322bd (0x85aa004 0x9327004 0x0 0x0)
0x92e13b78 : 0xa01e63 (0x85aa004 0x9327004 0x0 0x0)
0x92e13c18 : 0x9fe46f (0x0 0x9 0x0 0x0)
0x92e13dc8 : 0xa0033e (0x0 0x600d600d 0x702a 0x92e13df8)
0x92e13e98 : 0x994582 (0xc1d0001c 0xaa910001 0x20802040 0x92e13ee0)
0x92e13ef8 : 0xd544eb (0x9161400 0x92e13f4c 0x0 0x7)
0x92e13f58 : 0xd54696 (0x9271c00 0xd5bb54 0x92e13f78 0x2a358d)
0x92e13f78 : 0x22fd09 (0x9271c00 0x0 0x0 0x0)
0x92e13fc8 : 0x2a06cc (0x863ea0 0x0 0x10 0xd3e0cc0)
Kernel Extensions in backtrace (with dependencies):
com.apple.driver.AGPM(100.12.19)@0xd51000->0xd5bfff
dependency: com.apple.iokit.IOGraphicsFamily(2.2)@0x963000
dependency: com.apple.iokit.IONDRVSupport(2.2)@0x985000
dependency: com.apple.iokit.IOPCIFamily(2.6)@0x952000
com.apple.nvidia.nv50hal(6.2.6)@0x15e5000->0x19f9fff
dependency: com.apple.NVDAResman(6.2.6)@0x992000
com.apple.NVDAResman(6.2.6)@0x992000->0xc7ffff
dependency: com.apple.iokit.IOPCIFamily(2.6)@0x952000
dependency: com.apple.iokit.IONDRVSupport(2.2)@0x985000
dependency: com.apple.iokit.IOGraphicsFamily(2.2)@0x963000
BSD process name corresponding to current thread: kernel_task
Mac OS version:
10J567
Kernel version:
Darwin Kernel Version 10.6.0: Wed Nov 10 18:13:17 PST 2010; root:xnu-1504.9.26~3/RELEASE_I386
System model name: MacBookPro6,2 (Mac-F22586C8)
System uptime in nanoseconds: 1056892162111
unloaded kexts:
com.apple.driver.AppleUSBUHCI 4.1.5 (addr 0x1446000, size 0x65536) - last unloaded 125618059448
loaded kexts:
com.vmware.kext.vmnet 3.1.2
com.vmware.kext.vmioplug 3.1.2
com.vmware.kext.vmci 3.1.2
com.vmware.kext.vmx86 3.1.2
com.paragon-software.filesystems.ntfs 82
at.obdev.nke.LittleSnitch 2.2.05
com.apple.driver.AppleHWSensor 1.9.3d0 - last loaded 31366624745
com.apple.filesystems.autofs 2.1.0
com.apple.driver.AGPM 100.12.19
com.apple.driver.AppleMikeyHIDDriver 1.2.0
com.apple.driver.AppleMikeyDriver 1.9.9f12
com.apple.driver.AppleHDA 1.9.9f12
com.apple.driver.AudioAUUC 1.13
com.apple.driver.AppleUpstreamUserClient 3.4.5
com.apple.driver.AppleMCCSControl 1.0.17
com.apple.driver.IOBluetoothBNEPDriver 2.3.8f7
com.apple.driver.SMCMotionSensor 3.0.0d4
com.apple.kext.AppleSMCLMU 1.5.0d3
com.apple.DontSteal_Mac_OSX 7.0.0
com.apple.iokit.CHUDUtils 201
com.apple.iokit.CHUDProf 216
com.apple.driver.AudioIPCDriver 1.1.6
com.apple.driver.ACPISMCPlatformPlugin 4.5.0d5
com.apple.driver.AppleGraphicsControl 2.8.68
com.apple.driver.AppleLPC 1.4.12
com.apple.GeForce 6.2.6
com.apple.driver.AppleIntelHDGraphics 6.2.6
com.apple.driver.AppleIntelHDGraphicsFB 6.2.6
com.apple.driver.AppleUSBTCButtons 200.3.2
com.apple.driver.AppleUSBCardReader 2.5.8
com.apple.driver.AppleIRController 303.8
com.apple.driver.AppleUSBTCKeyboard 200.3.2
com.apple.iokit.SCSITaskUserClient 2.6.5
com.apple.BootCache 31
com.apple.AppleFSCompression.AppleFSCompressionTypeZlib 1.0.0d1
com.apple.iokit.IOAHCIBlockStorage 1.6.3
com.apple.driver.AppleUSBHub 4.1.7
com.apple.driver.AppleFWOHCI 4.7.1
com.apple.driver.AirPortBrcm43224 426.36.1
com.apple.iokit.AppleBCM5701Ethernet 2.3.9b6
com.apple.driver.AppleEFINVRAM 1.4.0
com.apple.driver.AppleSmartBatteryManager 160.0.0
com.apple.driver.AppleUSBEHCI 4.1.7
com.apple.driver.AppleAHCIPort 2.1.5
com.apple.driver.AppleACPIButtons 1.3.5
com.apple.driver.AppleRTC 1.3.1
com.apple.driver.AppleHPET 1.5
com.apple.driver.AppleSMBIOS 1.6
com.apple.driver.AppleACPIEC 1.3.5
com.apple.driver.AppleAPIC 1.4
com.apple.driver.AppleIntelCPUPowerManagementClient 105.13.0
com.apple.security.sandbox 1
com.apple.security.quarantine 0
com.apple.nke.applicationfirewall 2.1.11
com.apple.driver.AppleIntelCPUPowerManagement 105.13.0
com.apple.driver.AppleProfileReadCounterAction 17
com.apple.driver.DspFuncLib 1.9.9f12
com.apple.driver.AppleProfileTimestampAction 10
com.apple.driver.AppleProfileThreadInfoAction 14
com.apple.driver.AppleProfileRegisterStateAction 10
com.apple.driver.AppleProfileKEventAction 10
com.apple.driver.AppleProfileCallstackAction 20
com.apple.driver.AppleSMBusController 1.0.8d0
com.apple.iokit.IOFireWireIP 2.0.3
com.apple.iokit.IOSurface 74.2
com.apple.iokit.IOBluetoothSerialManager 2.3.8f7
com.apple.iokit.IOSerialFamily 10.0.3
com.apple.iokit.CHUDKernLib 208
com.apple.iokit.IOAudioFamily 1.8.0fc1
com.apple.kext.OSvKernDSPLib 1.3
com.apple.driver.AppleHDAController 1.9.9f12
com.apple.iokit.IOHDAFamily 1.9.9f12
com.apple.iokit.AppleProfileFamily 41
com.apple.driver.AppleSMC 3.1.0d3
com.apple.driver.IOPlatformPluginFamily 4.5.0d5
com.apple.driver.AppleSMBusPCI 1.0.8d0
com.apple.nvidia.nv50hal 6.2.6
com.apple.NVDAResman 6.2.6
com.apple.iokit.IONDRVSupport 2.2
com.apple.iokit.IOGraphicsFamily 2.2
com.apple.driver.BroadcomUSBBluetoothHCIController 2.3.8f7
com.apple.driver.AppleUSBBluetoothHCIController 2.3.8f7
com.apple.iokit.IOBluetoothFamily 2.3.8f7
com.apple.iokit.IOSCSIBlockCommandsDevice 2.6.5
com.apple.iokit.IOUSBMassStorageClass 2.6.5
com.apple.driver.AppleUSBMultitouch 206.6
com.apple.iokit.IOUSBHIDDriver 4.1.5
com.apple.driver.AppleUSBMergeNub 4.1.5
com.apple.driver.AppleUSBComposite 3.9.0
com.apple.iokit.IOSCSIMultimediaCommandsDevice 2.6.5
com.apple.iokit.IOBDStorageFamily 1.6
com.apple.iokit.IODVDStorageFamily 1.6
com.apple.iokit.IOCDStorageFamily 1.6
com.apple.driver.XsanFilter 402.1
com.apple.iokit.IOAHCISerialATAPI 1.2.5
com.apple.iokit.IOSCSIArchitectureModelFamily 2.6.5
com.apple.iokit.IOUSBUserClient 4.1.5
com.apple.iokit.IOFireWireFamily 4.2.6
com.apple.iokit.IO80211Family 312
com.apple.iokit.IONetworkingFamily 1.9
com.apple.iokit.IOUSBFamily 4.1.7
com.apple.iokit.IOAHCIFamily 2.0.4
com.apple.driver.AppleEFIRuntime 1.4.0
com.apple.iokit.IOHIDFamily 1.6.5
com.apple.iokit.IOSMBusFamily 1.1
com.apple.kext.AppleMatch 1.0.0d1
com.apple.security.TMSafetyNet 6
com.apple.driver.DiskImages 289
com.apple.iokit.IOStorageFamily 1.6.2
com.apple.driver.AppleACPIPlatform 1.3.5
com.apple.iokit.IOPCIFamily 2.6
com.apple.iokit.IOACPIFamily 1.3.0
Model: MacBookPro6,2, BootROM MBP61.0057.B0C, 2 processors, Intel Core i5, 2.53 GHz, 4 GB, SMC 1.58f16
Graphics: NVIDIA GeForce GT 330M, NVIDIA GeForce GT 330M, PCIe, 256 MB
Graphics: Intel HD Graphics, Intel HD Graphics, Built-In, 288 MB
Memory Module: global_name
AirPort: spairportwireless_card_type_airportextreme (0x14E4, 0x93), Broadcom BCM43xx 1.0 (5.10.131.36.1)
Bluetooth: Version 2.3.8f7, 2 service, 19 devices, 1 incoming serial ports
Network Service: Ethernet, Ethernet, en0
Network Service: AirPort, AirPort, en1
Serial ATA Device: Hitachi HTS545050B9SA02, 465.76 GB
Serial ATA Device: MATSHITADVD-R UJ-898
USB Device: Hub, 0x0424 (SMSC), 0x2514, 0xfd100000
USB Device: Built-in iSight, 0x05ac (Apple Inc.), 0x8507, 0xfd110000
USB Device: IR Receiver, 0x05ac (Apple Inc.), 0x8242, 0xfd120000
USB Device: Hub, 0x0424 (SMSC), 0x2514, 0xfa100000
USB Device: Internal Memory Card Reader, 0x05ac (Apple Inc.), 0x8403, 0xfa130000
USB Device: BRCM2070 Hub, 0x0a5c (Broadcom Corp.), 0x4500, 0xfa110000
USB Device: Bluetooth USB Host Controller, 0x05ac (Apple Inc.), 0x8218, 0xfa113000
USB Device: Apple Internal Keyboard / Trackpad, 0x05ac (Apple Inc.), 0x0236, 0xfa120000
-Thanks.
Message was edited by: GoreLeech

GoreLeech wrote:
Hello,
Having searched high and low, I can't seem to find a solution to my predicament.
Sun Feb 13 20:50:44 2011
panic(cpu 0 caller 0x9f8bfa): NVRM[0/1:0:0]: Read Error 0x00000100:
Graphics: NVIDIA GeForce GT 330M, NVIDIA GeForce GT 330M, PCIe, 256 MB
Hi there, GoreLeech,
as per above extract from your error log, you have experienced a kernel panic due to problems with your Nvidea GeForce GT 330 M graphics card that has a 256 MB memory.
This may be due to the card not having enough memory for what you are doing, the only thing, I can suggest here is to call Apple, and get the machine checked out. You can run the Apple hardware test at home but I'd recommend getting it booked in with Apple. What is worse: A computer that randomly malfunctions, or doing without it for up to one week (often they repair it within a day!)?

Help MacBook Pro 13" early 2011 suddenly black screen in Windows 7 SP1. EFI 2.2.

Hi, everyone, I need help here.
Apple MacBook Pro 13" early 2011 preinstall Lion version, EFI 2.2, Boot Camp 4.0. suddenly black screen in Windows 7 SP1 (black screen and also no sound at all, need to press power button to off). What happen?? Please someone tell me what to do?
I have delete bootcamp HD and reinstall windows 7 but the problem is still here, I have reset PRAM and SMC too.
The video on the black screen: (http://www.youtube.com/watch?v=z3dLTFSD-v8)

Oh I actually have the problem in Mac OS, not even using the Bootcamp or Windows 7
Csound1 wrote:
lokiman wrote:
I am having the exact same problem with my 13" early 2011 Macbook Pro. I have 10.6.8. I used the disk that came with the laptop to restore the OS to 10.6.7 but the problem existed there too. I have now updated it back to 10.6.8. The problem still exists. This doesn't seem to be limited to an OS version and seems like an issue with device driver or with hardware. I will try to take it to the Apple store and see if this gets resolved.
You too have a black screen in Windows 7. ?

Mac Pro 1,1 Ati X1900xt black screen on cold boots

Similar Messages

Maybe you are looking for