Mac Pro 2008 Apple Cinema Displays are black and there are start up issues

I have a Mac Pro 2008 Dual quad 2.8 GHz. I have two Apple Cinema Displays (graphics are the standard ATI Radeon HD 2600 – 2 dual link DVI. I have 4 2-GB RAM sticks (8 GB total).
Neither of my displays are showing anything. Their power lights are on but they are completely black throughout the start up process. In addition when I try to boot up with both graphics cards installed, I get nothing – no beeps no chimes. If just one card is installed (either card in either slot) the computer beeps, chimes and makes the sounds of booting up, but not a flicker on the displays. RAM does not seem to be the issue as I have tried booting with several configurations of RAM sticks with no negative or positive effects. I tried booting up with Hard Drives 1 & 2 removed with no effect. I have tried several different start up moods and have reset PRAM.
My guess is that there is something wrong with the motherboard. Or is it possible that both graphics cards are bad?

The "least intensive" thing you can do is hold down Alt/Option at Startup. Thsi invokes the all-in-ROM Startup Manager, which will light up the screen gray or blue, then attempt to draw an Icon for each potentially-bootable Volume attached (if any). It works as if in slow motion, so you must be patient. If no activity after about two minutes you may count that as a failure.
The next most intensive is to attempt to boot from an incorruptible source of software, such as an Installer/Utilities DVD. This again uses the "one-size-fits-all" display driver, and attempts to load software off the DVD. The dark colored Apple is loaded off a drive -- it is not present inside your Mac.
The next most intensive step is to attempt to boot into Safe Mode. This also uses the "one-size-fits-all" display Driver, and does a disk check as it starts up, adding five minutes to the startup time. It then drwas a login screen and deamds your username and password, even if you normally auto-login.

Similar Messages

How do i connect my Fujitsu Tablet + mac Pro to Apple Cinema Display 23'?

Dear Mac users
thanks in advance for your help.
I currently own:
• Fujitsu T 4220 (tablet) – Mobile Intel 965 Express – 60 Hertz – goes up to 1680*1050 (guess SXGA) – (it has the following other supported resolutions: 1400*1050, 1280*1024, 1280*768, 1280*720, 1024*768, and 800*600)
• Mac Pro
• Apple Cinema Display 23’
What I would like to do is, please refer to the jpeg posted on http://www.flickr.com/photos/34831802@N06/3234336204/, connect – at the same time – my tablet pc and my Mac Pro to the 23' Apple Cinema Display and switch (when I need) from tablet to MacPro using the same 23’ ACD. Top would be to be able to switch for one to the other while they’re both switched on. Usually on 2 pc’s with vga I’d use a switch A → B (in the jpeg it would be I → E) with a selector.
Have been reading different posts such as: http://discussions.apple.com/thread.jspa?messageID=8000641&#8000641 or http://discussions.apple.com/thread.jspa?messageID=6530475&#6530475 or
http://discussions.apple.com/thread.jspa?messageID=7417258&#7417258
+ others on the net and have (hopefully) understood that:
a) from Vga to Dvi I need a converter such as Geffen’s or similar
b) the problem with ACD 23’ is that it has only 3 resolutions: 1024*640, 1280*800 or 1920*1200
In the attached image I guessed a connection in order to connect – at the same time – both the machines to the 23’ ACD:
1) my fujitsu tablet (i in the image) has to be connected, with a Vga cable (h), to the Vga → Dvi converter (g).
2) from the Vga → Dvi converter (g) I need to connecto to the Dvi switch (c)
3) easier is connecting the Mac Pro (e), since I only need a Dvi cable (d) to connecto to the Dvi switch (c)
4) the Dvi switch (c) will then be connected to the 23’ ACD with a Dvi cable
Now, my questions are:
a) is the solution described above (Vga cable (h) to the Vga → Dvi converter (g)) a good solution or should I use, instead, a docking statione that comes with a Fujitsu Port Replicator (FPCPR65) which has a 1 x DVI-D port?
b) Given the 3 resolution accepted by the 23’ ACD (1024*640, 1280*800 or 1920*1200), I do not understand if I can use my tablet through a Vga to Dvi Converter and at which resolution (my tablet has the following other supported resolutions: 1680*1050, 1400*1050, 1280*1024, 1280*768, 1280*720, 1024*768, and 800*600).
c) Is there a way, also using an external video card or converter, to bring my resolution from 1680*1050 to 1920*1200? (the 16:10 ratio is in fact the same = WXGA (1280x800), WXGA+ (1440x900), WSXGA+ (1680x1050), WUXGA (1920x1200)
d) Talking about Vga → Dvi converter (g), am aware of the gefen product. Can you please list some others that might be good as well?
e) And how about the DVI switch? Any will work? Any particular suggestion?
Thank you very much for your help.
If you have any other suggestion, please let me know.
Regards,
Emil

Noone to help me?
No ideas?
Thanks,
Emil

Macbook Pro 2008. My screen stayed black and is unresponsive.

Macbook Pro 2008. My screen stayed black and is unresponsive and sleep light is on. I shut down and then restarted and nothing happened on screen but sleep light came on and is solid.

It could possibly be the video card, or the logic board. You could try a smc reset if you have not done s yet. smc reset:
http://support.apple.com/kb/HT3964
I had an issue similar to this, and there was a bad logic board, hard drive and video card.
You might want to bring it in to the Apple store, they do the diagnostic for free and give you a repair price.
They offer a flat repair rate, which they fix what ever is wrong as long it was due to liquid damage.
The repair cost me about 1/3rd the price of a new machine and the machine has been fine ever since.
It's worth getting it checked out.
ATB

I converted some songs in iTunes to work with an eMusic device. I'd like to delete them, but I'm not sure which of the duplicated songs to delete. Some titles are black and some are gray.

I converted some songs in iTunes to work with an eMusic device. I'd like to delete them, but I'm not sure which of the duplicated songs to delete. Some titles are black and some are gray.

let's just doublecheck some things quickly. do any of the affected songs play in itunes at the moment? if so, when you play them, do they ask to be authorised?
if so, does the authorisation go through successfully, or do you get an error message? (if you get an error message, let us know what it says. include error message numbers if you're getting any.)
if the authorisation seems to go through successfully, with the authorised songs sync to the ipod?

Some photos in iphoto are missing and there are blank thumbnails which when i try to open them show an exclamation sign

some photos in iphoto are missing and there are blank thumbnails which when i try to open them show an exclamation sign

The exclamation make is an indication that iPhoto has broken the file path to the original photo.
Make a temporary, backup copy (if you don't already have a backup copy) of the library and apply the two fixes below in order as needed:
Fix #1
Launch iPhoto with the Command+Option keys held down and rebuild the library.
Select the options identified in the screenshot.
Fix #2
Using iPhoto Library Manager to Rebuild Your iPhoto Library
Download iPhoto Library Manager and launch.
Click on the Add Library button, navigate to your Home/Pictures folder and select your iPhoto Library folder.
Now that the library is listed in the left hand pane of iPLM, click on your library and go to the File ➙ Rebuild Library menu option
In the next window name the new library and select the location you want it to be placed.
Click on the Create button.
Note: This creates a new library based on the LIbraryData.xml file in the library and will recover Events, Albums, keywords, titles and comments but not books, calendars or slideshows. The original library will be left untouched for further attempts at fixing the problem or in case the rebuilt library is not satisfactory.
OT

Dual Display Problem - Mac Pro / 23" Apple Cinema

Hey guys, I'm having a bit of a hard time right now. Here's my situation. I'm using my Mac Pro with a primary HD Apple Cinema Display 23". I just recently stumbled upon a Sony HS95P. I've used this monitor before as a second display a few years back. I bought a " DVI 24+1 male to VGA female adapter DVI-D DVI-I DVI-A " and plugged it into my computer, no problem. Display shows up in system preferences, when I check mirror displays it takes the resolution of the 2nd display and the Sony flashes. However no screen, Blacked on the Sony. When I set up the displays to run into eachother, I can venture my mouse over onto where the other monitor would be, however it's black on the Sony.
What could be the problem? I didn't buy the Apple adapter, but could this REALLY be that serious of an issue? I didn't use it in the past, atleast I don't think I did.. Also could it be the OS? I'm using 10.6.8. Any help or advice/things to try would be awesome... I have two DVI slots in the back of my Mac Pro, gfx card is a NVIDIA GeForce 7300 GT. Thanks guys.

I'm back. Got my Mac Pro back from repair today. Ahhh...25" screen. However, they (the Apple Repair People) have put a new GeForce 8800GT in, to replace the old one.
And the final bill was $380 CDN ($40 for work, the rest for the card, around $300.)
What's Apple's policy on graphics card replacement, even if the customer is paying for it? I thought I asked for a new ATI 5770 card, but maybe I was wrong. I don't think I can take her back in and ask 'em to put a better card in there, and only ask for a bit more to cover the difference in price. I've got a feeling it doesn't work like that.....
thanks
John B

23" Apple Cinema Displays gos black when routed through DVI extenders boxes

I have an ATI radeon 9650 with two DVI ports. My new set up requires my Mac to be further than the dvi connector's present lenght to my 2 HD cinema displays. I purchased 2 DVI extender boxes. Once connected the Utilities does not show the displays as Cinema HD Displays. And worse yet they both go black and the power light blinks. When I hook up the 23" directly through DVI to the G5 both displays come on. However the one connected through the extender box still shows the wrong display profile.
I have check and re-checked the cables, extender boxes, my graphic card and all seems to test out properly. I know this because I have another G5 with same specks that I have tested these hardwares on. Finally I thought it was my Bootup drive so I did a full erase and clean reinstall. the monitors worked fine for 10 minutes and then when I clicked on Displays in system pref window they both went black again. I can only conclude that the DVI extender box is somehow changing the signature of the HD Displays and the the system freaks out!
THE MODEL OF THE DVI extenders are DAS 101,and 101R
www.cooldrives.com/cadvexcat5dv.html ;
I am at my wits end. I need to get to work before I loose all my clients. PLEASE SOMEBODY HELP!
PS total lenght of CAT5 DVI extenders from Mac to Display 15ft max

Naelm G, I just read your first post a little more carefully. Is it true you are only trying to place the Cinema displays 15 feet away from the Mac? That's not very far. If you don't care about also extending the Firewire and USB, then you might be able to get away with a simple 10 foot DVI extension cable like this:
http://www.monoprice.com/products/product.asp?cid=102&cp_id=10209&cs_id=1020903&pid=2406&seq=1&format=2
The combinded length of the Cinema's built-in cable plus the 10 foot extension cable will be more than 15 feet. This would be the cheapest way to go by far.
Or if you want to extend the Firewire and USB along with the the video, then Gefen makes an extender that will do that:
http://www.gefen.com/kvm/cables/applecombocable.jsp

How to use Mac Mini & Mac Pro on same Cinema Displays?

Does it have a tool?

Hi,
you can use the display with both of the machines, however you require a Display Switch,

Bridge CS5.1 Tools are missing and there are no startup scripts available.

Brand new MBP with Creative Suite CS5. Not sure what happened to the Bridge Image Processing Tools that where readily available in CS4. I looked for the Startup Scripts mentioned in other forum posts but this folder is empty: Library > Application Support > Adobe > Bridge CS5.1.
Why make us hunt for Startup Scripts?

I think you may be misunderstanding me.
With many advantages with using mail for this forum the disadvantage sometimes is you don't have oversight in the whole thread.
I was merely reacting on Curt with the CS5 and CS5.5 solution that solved some problems earlier this year but reading the thread again that seems not related to yours.
Shortly before Curt his post I read your post about renaming the default folder name (which to me sounds bad). Hence my reference to a solution of an older problem that was solved by creating a new folder with the 5.1 addition and copy the scripts in there
However I still don't understand why you are not able to have a normal setup after clean install.
Without having experience with Lion I really would try the Recovery Disk for resetting your user account. With Pre Lion you could do an Archive and Install and it seems Lion also has such an option.

All of the webpages are showing up "strange" not all the colors are showing, not all the correct boxes are showing, and there are numerous errors in the error console (which doesn't help me)! Is there just a way to reset everything to go back to normal??

Some of the error codes are:
filter
background
border radius
box shadow
height

See:
* http://kb.mozillazine.org/Website_colors_are_wrong
* http://kb.mozillazine.org/Websites_look_wrong
Other things that need attention:
Your above posted system details show outdated plugin(s) with known security and stability risks that you should update.
# Shockwave Flash 10.0 r45
# Next Generation Java Plug-in 1.6.0_20 for Mozilla browsers
Update the [[Managing the Flash plugin|Flash]] plugin to the latest version.
*http://www.adobe.com/software/flash/about/
Update the [[Java]] plugin to the latest version.
*http://www.oracle.com/technetwork/java/javase/downloads/index.html (Java Platform: Download JRE)

How can I run a 27" Apple Cinema Display and another monitor from my MacBook Pro?

Hi everyone,
I recently purchased a brand new 15" MacBook Pro to replace my old one. I was told when ordering it that I would be able to hook up two external monitors to it using the Matrox DualHead2Go hardware. So, I also bought a 27" Cinema Display (non-Thunderbolt since it wouldn't work with the DH2Go). However, when I contacted Matrox they said their products don't support screens as large as the 27" ACD.
Bummer!
So, my question is: does anyone know how I can hookup a 27" Apple Cinema Display at 2560x1440 and a Acer 22" monitor at 1685x1050 (or, anything less really) to my new MacBook Pro?
I've looked around and haven't been able to find a good answer.
Thanks for your help!

Will something like this work? A USB to VGA adapter? Can I use this at the same time that I have a Cinema Display plugged into the Mini-DVI port and will they both work at the same time? Anyone know?
http://www.amazon.com/StarTech-Monitor-External-Adapter-USB2VGAE2/dp/B002FJQXXC/ ref=sr_1_2?s=electronics&ie=UTF8&qid=1329870330&sr=1-2

Bridge CS5 preview / slideshow not working on 27" Apple Cinema Display

I'm using my 2009 (black key) MacBookPro and Mac OS X 10.6.7 running Snow Leopard.
2.4 GHz Intel Core 2 Duo
4 GB 1067 MHz DDR3
Adobe Bridge CS5 works beautifully on my MBP, my photography workflow depends on Bridge.
However, when I attach my 27" Apple Cinema Display and try to preview images by hitting the space bar I get a gray screen. Likewise, the slideshow renders only gray.
It's not the "black out other monitor". I've cleared the cache to re-render all the previews.
I've scoured these forums as well as the Apple ones, and the helpful folks currently at Photoshop World in Orlando advised me that, collectively, the kind people here know everything. I know I can't be the only photographer who uses this configuration. I'd like to use the display for client previews/ordering.
I would so appreciate any tips you may have for me; thank you in advance for your time.
Warmly,
Darcy
http://hisandhersphoto.net

Yes, thank you. I found that post - among others when researching before I asked. I tried all the suggestions in that one and in the others.
My issue isn't low quality rendering in the preview and slideshow - my issue is NO rendering at all in slideshow and preview. It's just blank. Gray.
I deleted the cache in my library and through the Bridge program itself to rebuild the previews. I tried the various options of "software rendering" on and off, and different configurations in the preferences and none seem to make the preview or slideshow work. I have all the updates from Adobe and from Mac.
I tried importing the photos I need to show my clients (who are coming to my studio this evening!) into Lightroom 3, and the LR slideshow works. But using LR and having to import photos into it is an extra step not in my workflow.
Ideally, I can make Bridge work instead of making yet another resource-consuming copy of these photos on this computer via the Lr library.
So - current state is unsolved.
Lightroom 3 slideshow and preview works, but isn't ideal since it involves importing the images into Lr. Since that works - would that mean my video card is acceptable?
Bridge can show thumbnails on the 27" display but no preview or slideshow.
Bridge preview and slideshow works perfectly on my 15" MacBook Pro.
I'm so disappointed since I bought the 27" Apple Cinema Display this week and was told it would work with my computer "out of the box" - I was sure to ask several times, "so there's nothing else I need to buy or do to make this work with my programs? Just plugin and go?" and several times I was assured, "Yes... plugin and go."
I sure would appreciate anyone who's made Adobe Bridge work with a 27" display. Thank you!
Darcy

2008 Mac Pro and Apple Cinema Display 27"

Is there some sort of adapter that would allow me to plug the new Apple Cinema Display 27" with a 2008 Mac Pro? Or what change would I have to make to be able to work this out?

Adrian - did you end up getting an adapter and using it? I purchased the Atlona DVI to Mini DisplayPort Converter (AT-DP200) to connect my 2008 MacbookPro (with GeForce 8600M GT) to the new 27 in. Cinema display, and though it works, it looks a bit fuzzy in terms of resolution. Having read the response here about making sure it is a DUAL link converter, I was going to try to return it for the AT-DP400.
Then I read another thread on here that seemed to indicate that the AT-DP400 would not work at all with the 2008 Macbook Pro.
http://discussions.apple.com/thread.jspa?threadID=2585380&tstart=0
So now I'm confused. Just wondering what your experience is, if you ended up with getting the display and converter.

Hi, I have a mac pro 2008 and I was wondering if it possible to connect to the apple cinema 27'' display

Hi, I have a mac pro 2008 eand I was wondering if it possible to connect to the apple cinema 27'' display.

Yes using an apple 5770 video card and a dual link DVI adapter like the Atlona DP400 adapter.
Look at the hits in this google search for lots of other discussions on this topic.

No video on Mac Pro 266 + 20" Apple Cinema Display + ADC to DVI Adapter

When I boot my Mac Pro, I don't get a video signal. I currently have a 20" Apple Cinema Display (clear case) connected via an ADC to DVI adapter. I have connected the monitor/adapter on a Powerbook G4 wihout any issues, which rules out the monitor. I've tried everything: resetting PRAM/NVRAM, motherboard reset button, unplugging everything...nothing works.
Any help would be greatly appreciated!

Are you guys using the ADC to DVI adapter or the DVI to ADC adapter?
I have a clear 23" cinema display and I was thinking of getting a new Mac Pro... From what I can tell, you need the DVI to ADC adapter that sells for $100+. Is that correct?

Mac Pro 2008 Apple Cinema Displays are black and there are start up issues

Similar Messages

Maybe you are looking for