Mac Pro 3,1 and NVIDIA GeForce GT 120
Do The "NVIDIA GeForce GT 120" and the MacPro 3,1 2008 work together?
The NVIDIA GeForce GT 120 is made for the 2009 MacPro
Snow Leopard when it came out caused grief and "broke" as in dropped support, for some MacBook Pro owner's external drives.
10.3.0 Jaguar shipped with a known and fixed bug that was resolved in the testing and GM stage but got shipped and that one DID wipe out Firewire drives on install.
NTFS drivers (but not Paragon's) have stopped working or not been supported and updated so those using NTFS are a special case and vendors try to get new drivers out when there is a new OS. Trouble has been that for all the testing and early build access, the final product that ships is often far enough different that vendors have felt burned all too often and hold off investing time until they are certain. But many are ready or close to ready.
It is the old "1.0 is to be avoided" syndrome. Wait for 1.1 or so.
And always have two or more backup sets. Anyone that has lost a drive should have a spare and backup (and one set should be on the shelf and safe).
"Was hoping problem they had was fixed" with a new OS is wishful. But not if there is hardware or file system or a bad install or directory.
I think I have seen where some Apple GC's just don't have the support and drivers, or support features in a new OS that didn't exist 5-6 years ago.
Every new OS has improved but often something that was marginal or seemed to work, is pushed off the edge. Which is why that old RAM is now "bad RAM."
The more specific the easier it is to rule out or find out why. I think we often play "20 Questions" or "Whack a mole" to get to the bottom.
Similar Messages
-
Why can't I use my mid 2010 macbook pro with 8GB memoir and NVIDIA GEForce GT 330M 256MB to run 3D in photoshop CC?
3-D is very memory intensive.
System requirements | Photoshop
Mac OS
Multicore Intel processor with 64-bit support
Mac OS X v10.7, v10.8, or v10.9
2 GB of RAM (8 GB recommended)
3.2 GB of available hard-disk space for installation; additional free space required during installation (cannot install on a volume that uses a case-sensitive file system or on removable flash storage devices)
1024x768 display (1280x800 recommended) with 16-bit color and 512 MB of VRAM (1 GB recommended)**
OpenGL 2.0–capable system
Internet connection and registration are necessary for required software activation, membership validation, and access to online services.*
** 3D features are disabled and some Mercury Graphics Engine enhanced features may not work with less than 512 MB VRAM. Read the Help article.
Bottom line, you don't have enough VRAM
Nancy O. -
I have a mid 2007 MacBook Pro with 2GB of RAM and NVIDIA GeForce 8600M graphics card. Is it possible to upgrade the RAM and the graphics card?
The RAM can be upgraded as indicated below. The Graphics card can not be upgraded.
Maximum Memory
6.0 GB (Actual) 4.0 GB (Apple)
Memory Slots
2 - 200-pin PC2-5300 (667MHz) DDR2 SO-DIMM -
ere are the specs on the Mac I need more power on.
Mac Tower
Processor 2 x 2.26 GHz Quad-Core Intel Xeon
Memory 6 GB 1066 MHz DDR3 ECC
Graphics NVIDIA GeForce GT 120 512 MB
Serial Number H00354XF20G
Software OS X 10.8.5 (12F45)
Harddive 640 GB
SATA Disk
(2) Harddrives 1 TB
SATA Disk
RAM 6 slots total -- 6 are filled with 1GB
(3) UAD Quad cards installed
I use this computer stictly for audio recording.
Pro Tools 10.3.7
Interface Apollo 16
Pro Tools is curretnly not compatible with Maverick. Also, I believe that Pro Tools 10 only allows 4GB ram to be utilized (not sure )
I know Pro Tools 11 allows more, but not sure how much more. Also not sure if the upgrade to Pro Tools 11 I will have to purchase all new plug ins or if my existing ones will continue to work in it.
The platform changes from 32 bit to 64 with the upgrade to 11
If it is as simple as adding more ram, what mode-part #l would you recomeend. Can the processor be upgraded also ?
The new tube like Macs are non compatible with UAD Cards. Those cards a must my sessionsYou can use Activity Monitor to check if apps run as 32 or 64 bit - simply look at the "Kind" column (you may need to select it under View -> Columns) and see if the app in question is listed as "Intel" i.e. 32 bit or as "Intel (64 bit)".
While in Activity Monitor you can also check if Pro Tools is close to the 3-4 GB limit of a 32 bit app - if you aren't you will probably not benefit from more RAM.
Your MacPro (it appears to be a Early 2009 model) should have come with a small booklet showing how to install RAM and what kind of RAM that you need. Any RAM that fulfills the requirements should work but your safest choice is probably to buy from a retailer/online store that supports Macs as they will usually know what kind of RAM you need for your mac model.
Upgrading the CPUs should be possible, but I haven't seen Apple document how to do this, so you will probably have to google around a bit to find instructions and CPU part numbers.
Your choice of CPUs will also be limited by the motherboard and CPU socket so you may be limited to faster version of your current CPU chip and some slightly newer versions.
Going from your current CPU to the fastest version included in the 2009 MacPros would be going from 2.26 GHz to 2.93 GHz. This would only give a modest 30% speed boost. Using newer and highly clocked CPUs might boost this somewhat more maybe to 50% ? -
Mac Pro (Early 2008) and HP LP3065 30" display compatibility issue
Hello!
Is there FIX / Workaround to Mac Pro (Early 2008) and HP LP3065 30" display compatibility issue ? ( +w/ ATI Radeon HD 2600 XT display adapter+ ). Its really annoying problem :-/.
Main problem is when i start my Mac, my 30" HP screen dosen't wake up, it always on suspend mode. Sometimes it wakes up on the 3rd try orso, sometimes it ruins my motivation, ideas and i give up (talk about inspiration killer). If i connect PC Laptop to that screen, sreen wakes up straight away. ATI says display adapters "drivers" are included on the OSX install. Great. Weird thing is i didn't recognize this problem at all 6-8 months ago, so i thought my system is fine. So i can't return my HP screen anymore.
My choices are to buy another 30" screen or buy different display adapter; there's two choices atm i think;
*-ATI Radeon HD 3870 512MB PCI-E for Mac Pro (~200€)*
*-EVGA GeForce GTX 285 Mac Edition 1GB (~500€)* (this one has seperate OSX drivers).
_Can anyone confirm if those display adapters work with HP 3065 30" screen ?._
http://forums.macrumors.com/showthread.php?t=687624
http://discussions.apple.com/message.jspa?messageID=9388978
http://discussions.apple.com/thread.jspa?threadID=1794155&tstart=60
Br,
PetriThanks for all information. I haven't been Mac user very long . I just want to get rid of my annoying problem. I'll do music composing mainly on my Mac Pro. So, it dosen't really matter what display card i'm using, i want to just make sure it works with HP 3065 .
-
Upgrading Mac Pro (2009) from to NVIDIA Quadro 4000, what PCI slot to use ?
I am upgrading my Mac Pro (2009) from the Nvidia GT120 (stock) to the Nvidia Quadro 4000 for Mac. The GT120 was installed in the PCI Slot #1 and I would like to install the Nvidia Quadro 4000 in the PCI Slot #2, that way the Fan in the Graphics Card (Quadro 4000) will have better air circulation, is there any limitation or recommendation regarding the PCI slot to use ?, thanks a lot
I have an early Mac Pro 3,1.
The user manual I downloaded states:
Slot 1 PCI Express 2.0 16-lane
Slot 2 PCI Express 2.0 16-lane
So I'm assuming that means both slots 1 and 2 are the same and it doesn't matter which of my two graphics cards go in which slots?
Also, my second graphics card is a Quadro 4000 which is for Adobe Applications that use the CUDA engine. I don't have any monitors hooked up to it. -
My MacBook Pro 15-inch with NVIDIA GeForce 8600M GT graphics processors just failed. Do you guys know if apple still fixes them?
I tried last week. The best I could get was a discount on the repair, but the damage to my logic board by the GPU caused it to no longer boot. The program ended in December last year, but it has been extended in the past.
If you have no other damage you might be able to get a flat rate tier 1 repair if you are in the USA. -
I have a Mac Pro Mid 2010 and 2012 both running OS 10.8.5. Both using ATI Radeon HD 5770 1052 MB vid cards.
Using the standard Display that came with the Macs, everytime I'm working in Ilustrator CS5 or 6, the Document I am working on gets transparent, and I when I try to move a pallete or the Document itself, the pallet or doc leaves trails from where it was to where I moved it. The only way I can resolve it is to open the Display prefs, choose a lower res, then switch it back to the "Best for Display" option. This started happening on both machines after the 10.8.5 update. I have since gone through all the Pram and Board resets, even had Apple replace the Vid Card and nothing helps. Anybody have this issue. It only happens in Illustrator.Hi Marco@JustALittle,
I really apologise for the inconvenience.
I will have someone from the senior team reach out to you shortly.
Can you please send a private message to me with your contact number and the best time to reach you.
If you dont know how to do that refer : http://forums.adobe.com/thread/1184148 -
I have a mac pro for work and they made it log on windows at start up. how can i switch back to Mac as well so i will use the i cloud fetures ?
Is a version of Mac OS running on this Mac? Reboot and hold down the option key.
-
Radeon HD 5770 graphics card works perfectly with my MAC Pro 1,1 and Adobe CS6. However, I upgraded to Adobe CC and Photoshop CC disabled some filters and 3D functionality. The preference panel for Performance/Graphics Card in Photoshop CC is greyed out and inaccessible and shows this message -
"Photoshop detected an error in your display driver. Update or reinstall the driver and check Use Graphics Processor to retry."
I still have Photoshop CS6 installed and it still works perfectly. Anyone else with this issue? Is there a driver update for this compatable with my setup?
OS 10.7.5
Mac Pro 1,1
20gb ram
ATI Radeon HD 5770 Graphics Card
30" Apple Cinema HD displayafter going round with this Adobe was able to find the fix....opened the "show content" folder for the application Photoshop CC (control click on the application folder) and navigate to the sniffer file and rename it by putting a tilda ~ in front of the name..." ~sniffer ", close and open PhotoshopCC...and voila, problem solved... Thankyou Adobe support
-
I have a Mac Pro 1.1 and want to add one or two HD displays or HDTVs to my computer. I do a lot of work with Photoshop and need a larger work area.
What do I need to up grade my computer? Which displays and or HDTV's might be the most cost effective to get?Disk drive using native SATA bus interface will allow the drive to copy and always present and ready.
But once you have backup any hourly changes should be smaller and as long as the NAS and your switch should allow enough.
You should always have off line backups and don't rely on just one backup set or just TimeMachine.
WD RED models are designed for RAID and NAS and 7.2k instead of your more standard slower green 5400 rpm green models while still costing less than WD Blacks.
http://www.amazon.com/gp/product/B008JJLW4M/
How to clone your system:
http://macperformanceguide.com/Mac-HowToClone-backup.html
http://macperformanceguide.com/Mac-HowToClone.html
http://www.macupdate.com/app/mac/7032/carbon-copy-cloner
Using Cloning as a Backup Strategy
http://www.macupdate.com/app/mac/7032/carbon-copy-cloner
http://www.bombich.com/software/updates/ccc-3.5.html
Clone to internal, TimeMachine to NAS is one way to go at it. -
New Mac Pro with Lion and can't install FCP.
I got a new Mac Pro with Lion and can't install FCP that worked fine in SL. Is it not compatible? Is it really a PowerPC program??? I'm a videographer and rely on this software and to spend $300 to continue to use it after spending a lot more for this software 4 years ago! Tell me this is not the case and there is a solution to installing FCP.
How to run FCP 6 (FCS 2) under Lion.
The installer for FCP 6 (FCS 2) is a PPC app. The Programs themselves are Intel. If your trying to install FCP 6 (FCS 2) this work-around will work...
First you need to install Rosetta from your Snow Leopard OS installation disc:
http://docs.info.apple.com/article.html?path=Mac/10.6/en/27987.html
After doing that you can install FCP 6 (FCS 2). Remember, after installing FCP 6 (FCS 2) you need to apply the updates. This has been discuss many times in the Final Cut Studio forum.
If your trying to install FCP version 5.1 (FCS 1) (a PPC app) and below your out of luck....
If you need further help, here is the URL for the Final Cut Studio forum:
https://discussions.apple.com/community/professional_applications/final_cut_stud io?view=discussions
R -
Since installing Premiere Pro CC 2014 upgrade, Mac Pro jumpy video and freezes constantly
Since installing Premiere Pro CC 2014 upgrade, Mac Pro jumpy video and freezes constantly. Worked perfectly before. Anyone else finding these issues? I'm running a quad core Mac Pro, so it's definitely not the hardware.
I've maxed out the memory assignment, but this isn't a memory problem per se.
It looks like certain Premiere Pro conditions are associated with a huge increase in kernel_task memory, zeroing out any available free memory. In my case it seems to be associated with effects applied to titles or jpgs or imported psd (Photoshop) files.
Program restart pulls kernel memory back to the 1.3gb normal size.
Here's where I am at startup:
Within three minutes: -
First time user trying to set up new Mac pro, wireless mouse and wireless keyboard together?
So I just bought a new Mac Pro, wireless keyboard and mouse. i am a first time Mac user. How do I even get started......connect the wireless mouse and key board to the Mac Pro desktop to even get started??
Just turn on the mouse and keyboard and observe that the green light comes on and starts to blink then turn on the Mac. The Mac should give you on-screen instructions.
-
Mac pro 3,1 and ati hd5870 overheating (shut down issues)
Hi all I have an early 2008 mac pro 16gig ram and the ati hd 5870 on dual boot windows 7 64bit, it has been running brill for about a year but then I started getting random shut downs in windows and the occasional one in macOS 10.7 I upgrade to 10.8 loved some of the new features but the shuts down became unbareable in both OS I would also just get black screen on startup and have to do forced reboots etc.
If I took out the hd5870 and put back inthe original ati card everything worked as normal except the orginal card isnt supported in fcpX and I need this for my work when I take out the hd5870 card it is boiling hot so I have done some research and it appears I am not the only one with over heating issues.
I have seen there are several third party graphic card cooling options but mac being mac I dont seem to have any free additional power outputs to power a third party cooling device, so my question is this
1, is anyone selse having these issues and has figured out a way to stop the shut downs
2. has anyone or does anyone know how i can keep my card cool?
inside my mac is squeaky clean and so is the graphics card.
ps, typical it is just outside the 1 year warranty and the card is so expensive i didn;'t want to buy 1 every single year@ Hatter
Yup prior card was 8800gt and new card is nice and snug. 10.8 was not clean install, was upgrade. Ill try safeboot although not sure how/why that will fix any long term issues i have (which are random).. Trying 10.7 i had the same issues and was hoping that 10.8 wld fix.. Why go back to 10.6.8 when it should work in todays day and age? :(
@ Grant
Have done that now although not sure why something like this is not in the owners manual?!
Thanks for the help/suggestions so far guys, much apprec.. Feels like my pro is dying on me slowly but surely...
Any other bright ideas?
Maybe you are looking for
-
Certain Maintenance Plan not getting scheduled in the background job
Hi Gurus, I am facing an issue here. A weekly background job (RISTRA20) runs every weekend and schedules the maintenance plans. But we have noticed that some maintenance plans are not getting scheduled. i.e no orders or schedule is getting generated.
-
Java application doesn't work with utf8 encoding in linux?
I use Linux OS and local i18n resource file for Java internalization. Below is my source code. The Frame title can be internalized without any problem, but the button text can't be shown correctly. What is the problem with my code? It works fine in W
-
How can I sync my texts to my mac
How can I transfer text messages from my iPhone to my MacBook Pro?
-
Oracle 9i Automatic PGA Memory Management
Hello, my team and me, we are facing difficulties to change the size of the PGA used by our server processes for HASH JOIN, SORT... operators, here you can see the results of "select * from v$pgastat": [pgastat dynamic view results|http://pastebin.co
-
How to replace string with image( Say Smiley).........????
Hello To All Experts !! I wanna looking for some help in displaying image in my text area when should i type ":)" in text field..... I got some program through forums.... import java.util.*; import javax.swing.ImageIcon; public class TokenizeSmiley {