Mac pro 5,1 optical drive connection

Hi, it's me, John B again (sigh)
I am getting my new Mac Pro 5,1 ready for use and it's almost there....
I would liike to swap optical drives. I already bought a blu-ray drive fitted with a sata to ATAPI board for my older 2008 Mac pro, and it works fine. I am led to understand that the optical drive in the newer mac pro is SATA. I'm concerned that the Optical drive cable harness is a bit on the short side. It works, sure, but there isn't much slack at all. My fingers aren't that delicate and graceful , so is there such a thing as an optical drive connector extender cable? and I'd be needing two of them. Basically what I"m trying to ask is what kind of connector is it? I'm guessing SATA but I don't know for sure. So, I presume if I wanted to swap drives, I'd take the board off of the blu ray drive and fit it in my newer Mac Pro, and the stock superdrive would have the board fitted to it and go in my 2008 Mac pro and everything would be peachy ( I hope-fingers crossed)
thanks
John B

what kind of connector is it?
A single SATA power + data cable with a large, stiff connector on a cable oriented perfectly and exactly the right length. The cable for each drive seems to "hover" over the connector end of the drives until pressed into place on the drive. To install, slide the drive sub-enclosure halfway into place, press the cable(s) onto the end of the drive(s), then slide the drive sub-enclosure the rest of the way into its space.
[extension cable?] I'd be needing two of them.
An extension cable is not needed and would not be helpful. Also, there is no room in the 2009 and later model for a paddle-board of any description.

Similar Messages

Mac Pro 3.1 Optical Drives not recognized.

My Mac Pro (2008 2 x 2.8 Quad Core) 3.1 running OS X 10.10.1 has always had 2 optical drives. The first an Apple Superdrive as shipped and a second optical dvd/cd drive. Both have worked for years, although in recent tears, the 2nd drive experienced problems where it would not open. Finally it died all together and I removed it. I have added a replacement IDE optical drive and now neither optical drive works or is even recognised by the OS X. My system info shows "No Drives", yet both are installed and connected. I have rebooted many times, I have reinstalled OS X Yosemite, yet both drives are still missing as far as the computer is concerned.
Does anyone know how I may diagnose this problem further, or better still, how can I fix this issue.
Regards
Nermie

After checking connections, I would try a NVRAM reset:
http://support.apple.com/kb/HT1379
If it still doesn't show, I'd pull it and connect it to a different machine.
If it does't show there, I'd call it dead.
Oh, and as for the jumper, I wouldn't change it without changing the second drive as well.

Will my mac pro support 10 Optical drives?

I have a mid 2010 Mac Pro that currently has two Optical drives installed. I believe its the Two 2.4GHz Quad-Core Intel Xeon E5620 “Westmere” processors. I installed a Samaung 840 Evo for the operating system and I have a 6 TB raid installed with 16gb of ram. I am going to be using it to burn dvds on location for my events. I have a high volume of customers and I really like to get orders out before the weekend is over.
My question is can I daisy chain 10 optical drives to my mac pro? How do I gauge how much it can handle?
And if you can give me a comparrison between that and the new mac pro that would be great. I know that the new model is going to be a lot faster and if my 2010 model can't support 10 drives but the new one can then it will be time to make a change!
Thanks for your time

So there are duplicators that have multiple targets? I have a 10 set duplicator already so when I have clients purchase as groups I can duplicate but most of our orders are specific to just one customer. So I have the duplication.
My previous setup was 4-5 macbook pros all networked to a shared drive and I burned that way but our system is changing and we are putting the Mac Pro into play and so it would be easier just to have a set of drives all stacked in my road case instead of pulling the macbooks from other stations and then having to pack them up and etc. So if each drive could burn a differenct disc that would be great.
I use toast and I read somewhere that you can just duplicate it and then from there I would label all of the drives to match the toast duplicate it was running from.

Creative inspire t6300 5.1 surround on mac pro 1.1, optical out to 5.1 audio gear (digital sound decoder).

Hi there,
Been searching and trying a lot but no luck so far. I have a surroundset Creative Inspire t6300
to be able to add some more fun to movies and a few games on my mac.
I own an upgraded Mac Pro 1.1 under Snow leopard, 2.33 gHz, dual processor, 8 core, 8 gb memory.
Even though it`s a piece for the museum, it works very well for designwork I do for work. No real need
to update for me, so....
As I understand, the optical out is standard 5.1. (By the way, the only other ports are the basic sound ports out
and in on the Mac). So after some research I found and got the 5.1 audio gear decoder. I connected this with
an opticle cable and used the 3,5 jackets from the surroundset to connect to (from left to right) cen/sw, (yellow
jacket) fl/fr (green jacket), sl/sr (black jacket) on the decoder. All perfectly understandable and it seemed to work well.
But when I tested with some of the testfile you find when googling on that, I think there is something wrong,
the typical surround effect is not there, it rather sounds more like stereo or even 5 mono`s.
I`ve tried Soundflower and JackPilot, but couldn`t get it right. With Soundflower I was able to choose 5.1 setting
(was not possible before) but testing it didn`t work.
There is an extensive test of the decoder on the net by someone who really is deep into the technics of it all but
no luck there either.
Back to basics: is it right that the optical out is truely 5.1 on the mac? With several tests the unit SFE does not react.
But when I play some music with iTunes, it works (loud and clearly :-)). Maybe I need a visit to the audiologist ;-) ?
Anyone?
tested with: http://www.youtube.com/watch?v=eL9-sIZRDHg&channel=alexnosenko
http://www.youtube.com/watch?v=sMh_zvCw6us
https://www2.iis.fraunhofer.de/AAC/multichannel.html

Hello John, I figured it was a signal issue. All the speakers fire and the sound is great. I was running the speakers thru a Dell PC with a Creative X-Fi Elite Pro, THX Certified, 7.1 soundcard using a fiber optic from the Mac Pro to the Z906's, it worked great until the Dell died!!! When I bought the soundcard from Creative I also bought the GigaWorks S750, THX Certified, 700 watt, 7.1 speaker system, used the speakers for 11 years and then the woofer/amp said "I QUIT" Creative quit making the speaker system and the sound card. The satellite speakers from the Creative GigaWorks speaker system still sound great (rated at 78 watt each) and are a little better speaker than the one's that came with the Z906 and the wattage from the 906 is sufficient to drive the satellites without any distortion. Thank you for addressing my issue, you confirmed what I suspected all along, just needed to hear it from someone with the same setup.
One last question, I purchased a Diamond Multimedia USB Soundcard, can't use the fiber optic(not supported by Mac) but the green, tan and black RCA's plug in and produces adequetly. When you plug your 906's into the Mac Pro using the fiber optic how do you set your speaker configuration? When I plug into the mac pro with fiber optic the 'Audio Midi Setup' does not seem to see the 5.1 configuration. Any thoughts there?
Carl

I have a new Mac Pro. I want to use my old Mac Pro as a storage drive for photos and old documents, linked to my new Mac Pro. How do I set up the old computer?

I have a new Mac Pro. I want to use my old Mac Pro as a storage drive for photos and old documents, linked to my new Mac Pro. How do I set up the old computer? Both computers have OS X10.9.3. Currently they are connected by a Firewire 800 cable.

You certainly could keep the old Mac Pro in Firewire mode (hold down the T key on its keyboard as you boot) to show its drives on the new MP. This is basically as fast as putting the drives into a Firewire enclosure.
Or you could boot it normally and share its files over the network using the Sharing panel of System Preferences. If you turn on both File and Screen Sharing, you don't even need to have a monitor attached - you can do all administration using screen sharing. However, this method requires that you open all files over the network, which will be slower than the direct-connect method above, and may also not work with all applications.
Matt

After updating to mountain lion on my mac pro I am unable to connect my g-raid

After updating to mountain lion on my mac pro I am unable to connect my g-raid 1T external hard drive using the firewire connection? I have 4 places to plug the firewire into, none work. All ports used to work with Snow leopard?

Try this:
Boot into Safe Mode then restart normally.
Repair the Hard Drive and Permissions - Lion/Mountain Lion
Boot to the Recovery HD:
Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
Repair
When the recovery menu appears select Disk Utility. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported then click on the Repair Permissions button. When the process is completed, then quit DU and return to the main menu. Select Restart from the Apple menu.
If this does not work to fix the problem, then:
Reinstalling Lion/Mountain Lion Without Erasing the Drive
Boot to the Recovery HD: Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
Repair the Hard Drive and Permissions: Upon startup select Disk Utility from the main menu. Repair the Hard Drive and Permissions as follows.
When the recovery menu appears select Disk Utility. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the main menu.
Reinstall Lion/Mountain Lion: Select Reinstall Lion/Mountain Lion and click on the Continue button.
Note: You will need an active Internet connection. I suggest using Ethernet if possible because it is three times faster than wireless.

Using Mac Pro in Target Disk Mode Connected to MacBook Pro

Hi all,
I am trying to set up two macs to run off of the same monitors/keyboard/mouse/etc. I know about KVMs, but they are too expensive for my current setup.
I want to know if it's possible to run a 2006 Mac Pro in target disk mode connected to a brand new MacBook Pro 13" via a firewire to thunderbolt converter.
I would need to access the files, but also run the applications from the Mac Pro on the MacBook Pro.
Would such a setup work? Would I have to reboot each time I wanted to switch machines? Would there be a significant lag in the Mac Pro's performance?
Any tips or links to articles/etc. would be appreciated.
Thanks,
Nick

Hi Niel,
Thanks for the speedy response.
I should have clarified that I know that I can access the drive like a firewire drive. I'm more curious as to whether I can either:
1. use it's applications in target disk mode (based on your answer -- No, unless all the necessary system components are identical between the two computers).
2. Boot from the Target Disk computer as if it were a separate drive of my main computer. If so, since this is Firewire and not SATA, will I notice a severe loss of processing power?
Nick

You can't use The following message is stopping me access my disk utility. 'this version of the application "Disk Utility" with this version of OS X.' not only that my Mac pro keeps dropping my internet connection and logs on to BT Open.

After installing Yosmite, The following message is stopping me accessing my disk utility. 'You can't use this version of the application “Disk Utility” with this version of OS X.' you have “Disk Utility” 12.1.1.
not only that my Mac pro keeps dropping my internet connection and logs on to BT Open.
Help

For whatever reason you don't have the Yosemite version of Disk Utility which is 13. I suggest you reinstall Yosemite.
Reinstalling OS X Without Erasing the Drive
Boot to the Recovery HD: Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
Repair the Hard Drive and Permissions: Upon startup select Disk Utility from the main menu. Repair the Hard Drive and Permissions as follows.
When the recovery menu appears select Disk Utility. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the main menu.
Reinstall OS X: Select Reinstall OS X and click on the Continue button.
Download and install the 10.10.1 update.
Note: You will need an active Internet connection. I suggest using Ethernet if possible because it is three times faster than wireless.
Check that you have the current version of Disk Utility.

I have a Mac Pro with four hard drives. I currently have Lion installed on one hard drive. I want to have the option to boot from either Lion or Snow Leopard. How can I do this?

I have a Mac Pro with four hard drives. I currently have Lion installed on one hard drive. I want to have the option to boot from either Lion or Snow Leopard. How can I do this?

It's best to install Snow Leopard on one of the three remain drives without an Operating System.
You can then install the applications you need from the original media. Create a User Account using Setup Assistant.
Do you want to migrate User Accounts from the OSX LIon boot drive, or are you keeping the User Accounts separate?
Dual-booting just requires holding the option key during startup and selecting either Lion or Snow Leopard.

How do I clear the Disk and reinstall the OS on my new Mac Mini without an Optical Drive?

How do I clear the Disk and reinstall the OS on my new Mac Mini without an Optical Drive?

If it's a new mini, should have Mtn Lion on it. In any case, restart into recovery mode, and follow the instructions.

How do i install office for mac 2008 to my new i mac which has no optical drive. I have the Office discs and product key

how do i install office for mac 2008 to my new i mac which has no optical drive. I have the Office discs and product key

You could purchase any commonly available external USB DVD/CD writer, such as the excellent LG brand units sold on Amazon, for about $30 US. I've used an LG writer for years to save wear and tear on my older Superdrive.

Is it possible to use one of the mac pro's internal hard drives as a external drive that can be accessed by a macbook etc?

is it possible to use one of the mac pro's internal hard drives as a external drive that can be accessed by a macbook etc?

Only if you move it to an external enclosure and let them both access it through a file server.

I currently run Mac Pro with three hard drives. Can I dual boot or even triple boot with Snow Leaopard on one drive and Mountain Lion or Lion on others?

I currently run Mac Pro with three hard drives. Can I dual boot or even triple boot with Snow Leopard on one drive and Mountain Lion or Lion on others?
I need to keep Snow Leopard so that I can run some old softward.

If you are careful you can put at least two on one drive, having Recovery from Lion and Mountain Lion on their own drives though.
CCC can clone Lion Recovery - great for moving or backup.

I dropped my mac pro. The disc drive plays but will not record. medium drive error. How hard is it to replace the drive my self. i see screws on the bottom. Could I just order a new internal drive and replace it? Or is it too complicated for the average ?

I dropped my mac pro. The disc drive plays but will not record. medium drive error. How hard is it to replace the drive my self. i see screws on the bottom. Could I just order a new internal drive and replace it? Or is it too complicated for the average person? Would be cheaper to buy an external drive than to replace internal one? Any advice is appreciated

How certain are you the superdrive ONLY is at fault?
That depends on your skill level, if you grew up tearing things apart and putting them together, its absurd how easy it is.
For some however its too daunting. On a general skill level for the "average" person its about a 3 out of 10 in difficulty.
Can you order same? yes.

My mac pro suddenly stops working (2011), connection to the monitor stops, but de tiny light on computer still on and all sound stops. what's the problem?

my mac pro suddenly stops working (2011), connection to the monitor stops, but de tiny light on computer still on and all sound stops. what's the problem?

When the display turns off, it is not clear whether the computer has halted, or whether the display subsystem has failed.
Those tests determine whether:
a) Your Mac software had stopped working OR
b) Only the display had stopped working
If the pressing the Caps lock light on the keyboard lights the Caps Lock light on the keyboard, some software is still running -- your Mac has not halted.
If pressing Control-Eject on the keyboard, followed by the Return key shuts down your Mac, the software was still running.
¿Software was still running?
--Yes, the problem is ONLY in the display subsystem
--No, this is a computer-wide problem such as a kernel panic

Mac pro 5,1 optical drive connection

Similar Messages

Maybe you are looking for