Mac Pro and Firewire busses
In preparation for purchase of a Mac Pro, I tried to determine how many firewire bussess are available for the 4 ports. According to one piece of information, there is only one bus(!!) supporting all four ports.
http://developer.apple.com/documentation/HardwareDrivers/Conceptual/HWTechFireWire/Articles/FireWimplementation.html
This setup could result in some real issues when using multiple FW devices, such as cameras, etc.
Have any Mac Pro users noticed problems in using multiple FW devices or is the configuration very different than previous Mac towers?
G4 Powermac Dual Mac OS X (10.4.7) 1G RAM,200GB scratch int, FCPS, LaCie Ext FW DL DVDburner
In most cases, the 'single firewire bus problem' is overstated. Many of us use not only the built-in single bus connected to cameras, decks and drives, but are also multiplying those ports though hubs.
I have a FW400 hub with about five drives and a camera and deck hanging off it, some looped through, and a FW800 hub with another five drives hanging off it, again, some looped through. The other FW ports are also full. I've never had a single hiccup with this setup on both a Dual G4 and Quad G5, and I would expect the MacPro to be no different. (I am exclusively talking about DV-rez work - I certainly would not expect this setup to handle higher rez material).
Specifically, it seems Canon cameras do not play well with single-bus setups - there have definitely been problems reported with them.
Similar Messages
-
Mac Pro and FireWire M-Audio 1814
Can some one please HELP ME configure my Mac System with my Fire Wire?
all I need help with is hooking up the Speakers to the fire wire then the fire wire to the Mac so I can get the sound Out.
many thanks in advance..Dear Mr. Zarzowski, I'll do what I can. first try going to m-audio.com and under 'support' type in the model # of your thing...ah, I see. the M-audio has ts/trs connectors which use headphone style plugs (the big ones) so, depending on what connector your speakers have, you'd need a speaker connector to 1/4 inch adapter
as for the fireWire, you'd have to go into audio, then input/output, select the FireWire unit, then maybe output over Firewire. Also go into midi setup and make sure that's setup correctly, ie the output and input should be FireWire and not line in/line out. I presume the unit comes with software, ie a FireWire control panel? You might want to install that, too
HOpe that helped--JOhn B---considering a career in helpdesk
if it did, please reply, if it didn't, keep trying -
I have interface M Audio 400 with 400 firewire new Mac Pro has firewire 800 Do you think an adaptor will provide the same quality? Will the M audio 400 work with lion and new system or do I need new software? Thanks so much
If you have a little Firewire adaptor, everything should work fine. It does on my system.
-
I just replaced the hard drive for my Mac Pro, and I am trying to restore what is on my Time Capsule, but it wont connect, and only is giving me the pinwheel of death. What do i do?
You will need to boot from some alternate boot device to accomplish this, if you did not initialize the drive before installing it.
If you have another Mac, you may be able to use FireWire target disk mode.
If your MacBook has a DVD reader and you have a Mac OS X Installer/Utilities DVD, such as the one that shipped with it, you can boot from that DVD, answer only the "what Language" question, and wait a quarter minute for the MenuBar to be drawn. Then examine the Utilities menu or the Installer menu and Find Disk Utility. -
Going between Mac Pro and G4 laptop
Hi - I am needing to go out of town for a month and I need to keep working as business as usual with my system. In the past, I would clone my older G4 tower system drive to my G4 Powerbook and then back again when I returned home. This worked perfectly.
(Using 10.5.7)
Recently I upgraded to a Mac Pro and I know that with the Intel processor I cannot clone back and forth anymore since my Powerbook is a G4.
How can I keep my computer, mostly Mail, Dreamweaver and iCal, synced so I can keep my workflow with a good transition? My data is on a separate external drive that travels with me. I'm not worried about applications as I still have them installed on my Powerbook pretty much in the same way as my MP is set up.
#1 - I really need to have all of my Mail accounts (pop3) data - the sent and received messages - to be duplicated between the two systems before I leave and then when I return to the MP system. My Dreamweaver account settings would be important as well since I need to manage about over 100 different accounts and it helps to keep them current as I am frequently adding and editing account login data.
Suggestions?If you copy the entire user folder you will also copy the /Home/Library/ folder. Although this isn't necessarily a problem, if you have PPC plug-ins for contextual menus, preference panes, or input managers they will no longer work on an Intel machine. You would need to replace them with universal binary versions for compatibility. For more about migration from a PPC see the following:
A Basic Guide for Migrating to Intel-Macs
If you are migrating a PowerPC system (G3, G4, or G5) to an Intel-Mac be careful what you migrate. Keep in mind that some items that may get transferred will not work on Intel machines and may end up causing your computer's operating system to malfunction.
Rosetta supports "software that runs on the PowerPC G3, G4, or G5 processor that are built for Mac OS X". This excludes the items that are not universal binaries or simply will not work in Rosetta:
Classic Environment, and subsequently any Mac OS 9 or earlier applications
Screensavers written for the PowerPC
System Preference add-ons
All Unsanity Haxies
Browser and other plug-ins
Contextual Menu Items
Applications which specifically require the PowerPC G5
Kernel extensions
Java applications with JNI (PowerPC) libraries
See also What Can Be Translated by Rosetta.
In addition to the above you could also have problems with migrated cache files and/or cache files containing code that is incompatible.
If you migrate a user folder that contains any of these items, you may find that your Intel-Mac is malfunctioning. It would be wise to take care when migrating your systems from a PowerPC platform to an Intel-Mac platform to assure that you do not migrate these incompatible items.
If you have problems with applications not working, then completely uninstall said application and reinstall it from scratch. Take great care with Java applications and Java-based Peer-to-Peer applications. Many Java apps will not work on Intel-Macs as they are currently compiled. As of this time Limewire, Cabos, and Acquisition are available as universal binaries. Do not install browser plug-ins such as Flash or Shockwave from downloaded installers unless they are universal binaries. The version of OS X installed on your Intel-Mac comes with special compatible versions of Flash and Shockwave plug-ins for use with your browser.
The same problem will exist for any hardware drivers such as mouse software unless the drivers have been compiled as universal binaries. For third-party mice the current choices are USB Overdrive or SteerMouse. Contact the developer or manufacturer of your third-party mouse software to find out when a universal binary version will be available.
Also be careful with some backup utilities and third-party disk repair utilities. Disk Warrior 4.1, TechTool Pro 4.6.1, SuperDuper 2.5, and Drive Genius 2.0.2 work properly on Intel-Macs with Leopard. The same caution may apply to the many "maintenance" utilities that have not yet been converted to universal binaries. Leopard Cache Cleaner, Onyx, TinkerTool System, and Cocktail are now compatible with Leopard.
Before migrating or installing software on your Intel-Mac check MacFixit's Rosetta Compatibility Index.
Additional links that will be helpful to new Intel-Mac users:
Intel In Macs
Apple Guide to Universal Applications
MacInTouch List of Compatible Universal Binaries
MacInTouch List of Rosetta Compatible Applications
MacUpdate List of Intel-Compatible Software
Transferring data with Setup Assistant - Migration Assistant FAQ
Because Migration Assistant isn't the ideal way to migrate from PowerPC to Intel Macs, using Target Disk Mode, copying the critical contents to CD and DVD, an external hard drive, or networking
will work better when moving from PowerPC to Intel Macs. The initial section below discusses Target Disk Mode. It is then followed by a section which discusses networking with Macs that lack Firewire.
If both computers support the use of Firewire then you can use the following instructions:
1. Repair the hard drive and permissions using Disk Utility.
2. Backup your data. This is vitally important in case you make a mistake or there's some other problem.
3. Connect a Firewire cable between your old Mac and your new Intel Mac.
4. Startup your old Mac in Target Disk Mode.
5. Startup your new Mac for the first time, go through the setup and registration screens, but do NOT migrate data over. Get to your desktop on the new Mac without migrating any new data over.
If you are not able to use a Firewire connection (for example you have a Late 2008 MacBook that only supports USB:)
1. Set up a local home network: Creating a small Ethernet Network.
2. If you have a MacBook Air or Late 2008 MacBook see the following:
MacBook (13-inch, Aluminum, Late 2008) and MacBook Pro (15-inch, Late 2008)- Migration Tips and Tricks;
MacBook (13-inch, Aluminum, Late 2008) and MacBook Pro (15-inch, Late 2008)- What to do if migration is unsuccessful;
MacBook Air- Migration Tips and Tricks;
MacBook Air- Remote Disc, Migration, or Remote Install Mac OS X and wireless 802.11n networks.
Copy the following items from your old Mac to the new Mac:
In your /Home/ folder: Documents, Movies, Music, Pictures, and Sites folders.
In your /Home/Library/ folder:
/Home/Library/Application Support/AddressBook (copy the whole folder)
/Home/Library/Application Support/iCal (copy the whole folder)
Also in /Home/Library/Application Support (copy whatever else you need including folders for any third-party applications)
/Home/Library/Keychains (copy the whole folder)
/Home/Library/Mail (copy the whole folder)
/Home/Library/Preferences/ (copy the whole folder)
/Home /Library/Calendars (copy the whole folder)
/Home /Library/iTunes (copy the whole folder)
/Home /Library/Safari (copy the whole folder)
If you want cookies:
/Home/Library/Cookies/Cookies.plist
/Home/Library/Application Support/WebFoundation/HTTPCookies.plist
For Entourage users:
Entourage is in /Home/Documents/Microsoft User Data
Also in /Home/Library/Preferences/Microsoft
Credit goes to Macjack for this information.
If you need to transfer data for other applications please ask the vendor or ask in the Discussions where specific applications store their data.
5. Once you have transferred what you need restart the new Mac and test to make sure the contents are there for each of the applications.
Written by Kappy with additional contributions from a brody.
Revised 1/6/2009 -
Last Mac Pro with Firewire 400?
The new Mac Pro's look nice, but without Firewire 400 they're useless to me... Can anyone tell me when the last Mac Pro with Firewire 400 was released?...and what the speeds were on them? Thanks in advance if anyone can help.
Fair points, to be sure. I just think that, given the number of common/popular devices that are FW400 only, the removal of FW400 ports is a bit premature at this time. Like the OP said, it would be frustrating to buy a very expensive computer, and immediately have to expand in order to make use of fairly standard and not yet out-dated gear.
Dave Sawyer wrote:
Sorry to disagree, but to me, expecting a company to go to the expense of engineering in a different physical port just to save someone from having to use a simple, inexpensive cable adaptor seems a bit silly.
It couldn't be that hard/expensive, given that previous models had both. Though I certainly understand the idea of reducing cost wherever possible. -
Have just got a Mac Pro (and am also new to Macs). I have a two year old Panasonic NV-GS15 digital video camera attached via firewire, I can't pick up the camera at all...in i-movie, Final Cut Pro (5.1) or even see it when looking under the firewire port. Have been on Panasonic website and the driver information I found was related to PC/Windows. Have emailed Panasonic but they aren't replying.
Any suggestions/answers/wishes of luck?
Mac Pro Mac OS X (10.4.7) 2 x 2.66 Dual Core Intel Xeon, 2GB 667 MHzI have same problem with Mac Pro and Panasonic PV-GS120. I went to Apple store and tried Mac Pros over there and they all had the problem. PowerBooks (G4 and Intel) as well as iMacs can all see the camcoder fine and iMovie imports clips without problems. System Profiler does not show any FireWire devices once the camcoder is attached Mac Pro and /var/log/system.log reports that FireWire has been reset multiple times in the last minute. I've filled in the form to escalate issue to Apple but I have no idea when the issues is going to be addressed.
Mac Pro Mac OS X (10.4.7) -
I have an early 2008 Mac Pro and want to install a 3TB internal hard drive. Is this compatible? The manual indicates 1 TB per bay, but I have already installed two 2 TB hard drives in two other bays, and have had no problems. Any suggestions?
RE: SATA Bus speed:
Typical Rotating drives available today, whatever their SATA spec, can source data off the spinning platters no faster than about 125MBytes/sec.
SATA 3 is rated at 6G bits/sec, which theoretically is about 750 Mega Bytes/sec
SATA 2 is rated at 3G bits/sec, which is theoretically about 375 Mega Bytes/sec
SATA 1 is rated at 1.5G bits/sec, which is theoretically about 187.5 Meg Bytes/sec
None of the SATA Busses is a bottleneck for consumer Rotating drives you can buy today. Trying to speed up the SATA Bus will not provide any real-world performance increases for Rotating Drives.
https://discussions.apple.com/message/22690384 -
" help me please" I have Windows 7 32 bit installed on my mac pro and Bought Mini DisplayPort to VGA Adapter to connect to lcd tv But it does not work? why? please help me
I have to boot with a Windows
When I use the Mac operating system not have a problem and DisplayPort to VGA Adapter Working properly
why does not work with windows ?
What should I do؟
I'm grateful to give advice
tanks
[email protected]Someone in another section answered this. Thanks.
-
I have photoshop C6 on my MAC Pro and want to install it on my new MAC desktop. I sent the files with AirDrop but photoshop wont open I get an error message that it cant find the Library. Any thoughts?
download the installation files and install using your serial number or adobe id,
Downloads available:
Suites and Programs: CC 2014 | CC | CS6 | CS5.5 | CS5 | CS4 | CS3
Acrobat: XI, X | 9,8 | 9 standard
Premiere Elements: 12 | 11, 10 | 9, 8, 7
Photoshop Elements: 12 | 11, 10 | 9,8,7
Lightroom: 5.5 (win), 5.5 (mac) | 5.4 (win), 5.4 (mac) | 5 | 4 | 3
Captivate: 8 | 7 | 6 | 5
Contribute: CS5 | CS4, CS3
Download and installation help for Adobe links
Download and installation help for Prodesigntools links are listed on most linked pages. They are critical; especially steps 1, 2 and 3. If you click a link that does not have those steps listed, open a second window using the Lightroom 3 link to see those 'Important Instructions'. -
I have mac pro and firefox 3.0.19
I am trying to download a video from youtube.?
I can see the video. I want to download it and save in my computer to see it again.
I have download helper. While the 3 red,blue,and yellow sphere are turning, It gives me the choice of place to save,and when I click and choose desktop , for example, this message comes ."Conversion requires an external application that appears to be missing on your system. Configure conversion ?
When I click on okay, another page comes, which says" converter and a box next to it . in the box is written FFMpeg. but I can change it to MEncoder. In another box, says configure conversion rules. When I click on it, nothing happen.Thanks for your help.
== This happened ==
Every time Firefox opened
== I want to download a video from youtubeNo, this reply is not helpful. It simply generates this little gem:
"This service requires the conversion feature to be enabled.
Configure conversion ?"
And the same clicking on buttons that makes nothing happen and going around in circles with the escape key. -
i have a long-existing iPhone 4s with one apple id and started a job where I received a macbook with another apple id. how do i get my phone to sync with the Mac Pro and secondly how do i get my music on there?
No not bothered about sycing apps etc it is all about calendars and maybe notes. IN terms of how its done I just want it the easiest way and preferably so that if an entry is made on one calendar then it populates the other.
Thgius is beacuse I have my work diary on outlok, which I then link with my ical. I want to make sure that information is then shared with her.
Chris -
My 5yr old iMac will not connect to the Internet. All other computers at home will, including my Mac Pro and iPad. I'm at my wits end. What should I do?
Which OS are you using (update your user profile).Try a
SMC RESET
http://support.apple.com/kb/HT3964
Shut down the computer.
Unplug the computer's power cord and ALL peripherals.
Wait 15 seconds.
Attach the computers power cable.
Wait another 5 seconds and press the power button to turn on the computer.
The 5 second timing is important to a successful reset. -
IPhone not showing in iTunes on Mac Pro, and BLOWS keyboard on two Macs!
I have an extremely annoying issue since I upgraded my original iPhone to 2.0 and 2.1:
- I've got an iPhone (8GB, first gen) with 2.1 firmware
- Mac Pro early 2008
- Aluminium Keyboard (standard)
- iTunes 8
Whenever I attach my iPhone, the keyboard goes dead. Totally. Only way to re-animate it is by unplugging the iPhone and wait 5 seconds, then re-plug the keyboard. This is on a newly created Admin account on the Mac Pro and the iPhone that has been through a total factory reset back to 2.1 today...
And a newly re-installed iTunes 8 on (all computers).
Note my iPhone is no longer recognized in iPhoto or Aperture or iTunes on the Mac Pro either.
However, the iPhone works fine on a Mac Book Pro (newest model).
It does show up and sync on an iMac Intel 2.0 GHy, but kicks the Aluminum keyboard on that machine as well...
What is going on??
I will have to double-post this in iTunes and iPhone section, apologies in advance, but this is just too ridiculous... someone must have an answer to this. At least an explanation. I have been through every single USB port on my Mac Pro.
Apple "Genius" in Apple Store Regent Street recommended an archive & install of Leopard 10.5.x. Yeah right. I am working on this machine, I have not got time for that silly idea...
The thing is, this all worked fine before the 2.0/2.1 update... but why is the bl oo dy thing working on a new MacBook Pro and not on my Mac Pro?// Apologies for cross-posting this in three threads, but as it - at least for myself - provided an instant solution to a nagging problem, it should be alright. //
Alrighty, here we go - today I FINALLY made successful progress WITHOUT having to re-install my entire system...
I figured it was very weird that my iPod Mini would work fine on my Mac Pro USB ports, as all other small devices did too, but that the iPhone (first gen) would simply not trigger any reaction whatsoever.
The iPhone could be ruled out from being the funny one as it was instantly recognized on Macs in the Apple Shop. As I really did not feel I had time to archive & install and whatnot on my work machine, and the fact that I always thought my Mac Pro should have a few more (USB) ports, I researched suitable internal USB expansion boards.
After reading up about it, I decided to get this one: *Sonnet Allegro Express USB* - this card installs in seconds - you simply sht down your Mac Pro, pull the mains plug, take off the side door, unscrew the two thumbscrews holding the blind plates towards the back, take out one of the blinds, push the card in carefully but all the way in, re-attach the blind-holding plate and fire up your machine.
I plugged my regular iPhone dock into the back, pushed in my iPhone, and was instantly greeted by the short humming of the iPhone! Starting iTunes, the iPhone popped up in the side bar again - my precious iPhone is back alive and happy to sync contents!
Very happy to finally have found a solution.
If anyone tries this, I really hope it works as good for you as it did for me - if it doesn't, then for about $50 you've at least got those extra four USB ports on the back of your Mac Pro you always wanted
Good luck! -
I have moved from a G5 Powermac to an Intel Mac Pro and selectively porting over items from a backup hard drive.
How can I access and use documents and drawings created on the PC based computer ?Clarisworks, you need Appleworks, which will only work with Mac OS X10.6.8 or earlier. See this tip if you must go newer. Mac Pros with newer hardware configuration than July 20, 2011 can't use Mac OS X 10.6.8 or earlier without this tip and then it would be Mac OS X Server. I'm not sure if the new black Mac Pro supports that configuration or not.
iPhoto, there is an iPhoto for all versions of Mac OS X.
iTunes, there is an iTunes for all versions of Mac OS X. Note with iTunes versions 11 and later, which are needed for syncing with iOS 7 or or later, you will lose coverflow, if you liked that feature. Sadly you can't run an older version of iTunes from within Mac OS X 10.9 or later.
Sketchup: http://help.sketchup.com/en/article/60107 shows the versions that will work with intermediate Mac OS X versions, and this shows the latest version: http://help.sketchup.com/en/article/36208 be sure to click on the operating system you choose to use.
GIF - Viewing GIFs Apple's Preview can do that. Editing them, I like http://www.lemkesoft.com/ Graphicconverter.
DMG is able to be opened by all versions of Mac OS X. This are just "disk images" which store programs on a virtual disk that will open when double clicked. Frequently you'll find the installer of the said program inside. To find out if the program itself is compatible with 10.7 through 10.9, see http://www.roaringapps.com/
Otherwise see the resources on:
https://discussions.apple.com/docs/DOC-2455
If you end up deciding to stick with Snow Leopard.
Maybe you are looking for
-
FB 4.7 crashes on Building workspace (usually at 40%)
Happens several times a day, after saving a file when FB starts "building workspace". I'm on Windows 8. Any ideas, anyone? Cheers!
-
How do I stop y jpg email file from going to word?
-
CRM MSA 4.0: Instant Reporting
Dear all, when I run Sales Transactions --> Search; the system display a list with result and, all date fields have a corrent format (dd/mm/yyyy). If I use mouse right-button on the list, I can export the list into excel sheet, but, the date field
-
Hi, I am getting this error message when I try and join a meeting (this is after I have input the meeting ID and entry code given to me by the host): Live meeting cannot connect to the meeting. Try again in a few minutes. If you still can't connect
-
"Unrecognisable Format" when trying to open file in EXCEL for Mac
Hi guys, The other night I left my comp on, with a microsoft excel file open, and the battery went flat. Obviously the computer closed down, but the next day when I tried to open this particular file, all I can get is "This file is in an unrecognisab