Mac Pro (early 2008) cannot startup

Today, I shut down my Mac Pro (early 2008) for about two hours and now it just refuses to startup.
This is the symptom:
Power-on LED illuminates when power button is pressed and fans spin continuously but there is no boot tone or video
Apple Service Guide
1. Reseat video card. (Make sure video card is fully inserted in connector and end of card is 1. secured by the connector latch.) For video cards that require power cables, check that they are connected.
I have two GPUs. NVidia GeForce 8800 GT and NVidia GeForce GT120. Tried them individually. Cards' fans spinning. Check diagnostic LED and LED 7 & 8 no light. Only LED 2 Yellow and LED 9 Green.
2. Verify speaker cable is fully seated.
No idea where this is.
3. Reset logic board. Refer to “Resetting the Logic Board” in this chapter.
Same symptom. LED 7 & 8 no light. Only LED 2 Yellow and LED 9 Green.
4. Check diagnostic LED 3 and/or LED 4 for processor connection.
Off.
5. If only one of the CPU Error LEDs (LED 3 or 4) comes on, try swapping the processors. If the Error LED follows the processor to the other processor location, replace that processor.
Since LED 3 & 4 are off, I guess CPUs are fine.
6. Replace logic board
This seems to be a standard fix suggestion for all startup failures in the service guide. Anyway, to check if it's a logic board issue?
I tried this too:
System Reset
Mac Pro (Early 2008) has a system reset switch on the logic board that may be used to restart the system while it is powered up. This switch can be used to determine if a computer that won’t consistently boot from a cold start has power supply issues. Follow these steps to reset the system:
1. With the computer powered up, press the SYS_RST switch located in the upper right-hand corner of the logic board. To press the switch, use the nylon probe tool (Apple part number 922-5065).
2. If the computer boots after you press the SYS_RST switch, try shutting the computer off and restarting by pressing the front power button. If the computer restarts when you press the SYS_RST switch but not from a cold start, the power supply may need to be replaced.
and I experienced 1. Can conclude not power supply issue? Did diagnostic check and still the same LED 7 & 8 no light. Only LED 2 Yellow and LED 9 Green.
I checked both memory riser cards. No red light. Half a year ago, I experienced the same no chime startup issue and found that Apple's supplied DIMMs were the culprits. I tested individual DIMM and still no go.
At loss now.
Apart from sending in for repair, no budget for that, and other steps to revive my Mac Pro?

had this exact problem yesterday. this is how i solved it although im no apple genius
My Mac pro 3,1 simply woudlnt boot normally no matter how i tried to reset it. power light was fine, no ram errors, just no chime and no video.
how i fixed it:
1. shut down and unplug
2. open side case (you should be using an antistatic wrist strap if you do this)
3. unplug EVERYTHING. (remove all 4 HDDs, video cards, Ram boards, power cable, USB cable, audio1/8" jack, firewire cables. leterally you want it bare bones. only thing i left in was my superdrives)
4. i removed the logic board battery and while unplugged held the power button for 1 min to drain all capacitors on the board. left it unplugged for 10-15min after this
5. after 15 mins, the only things i put back were the logic board battery, ram boards, the audio jack to check for a boot chime, and the power cable. ( no video cards, no hard drives, not even the boot drive, no keyboard etc.)
6. press power button to boot. HOPEFULLY you head a chime. if you do, hold power button to power off system.
7. now only insert the boot drive and one video card into pci slot one (power plug should be out to install things)
8. start the computer back up and look for video. hopefully it asks for a keybaord and mouse on the screen
9. shut down without reinserting keybaord, mouse, or anything else.
10. unplug system after power off, and reinstall and plug back in EVERYTHING
11. reboot and hopefully all is well????
-Mitch

Similar Messages

Mac Pro (Early 2008) freezes, reboots to recovery system, trouble locating startup disk

I have two issues which may or may not be related with my Mac Pro. First, off and on for several months is has been frozen when waking from sleep. I can hit a key and see my desktop with the windows I left open, but I get the spinning beach ball and the time is typically several hours behind. The only way I can get it to start is to restart from the power button. This typically happens overnight when my computer has been asleep for a long time. Sometimes I hear the fan run while the computer is asleep and I don't know if that is related. I've tried switching from Firefox to Chrome to see if that was the problem since I typically have a few tabs open on Firefox when it freezes, but that does not solve the problem. The next step I plan to try is to get a can of compressed air and clean the fan and check if the video card air intake might be clogged, based on information I have read in various forums. Does anyone have other suggestions for things to try to eliminate the freezing? Another suggestion I read was to get a new logic board battery installed but I hate to lug this thing into an Apple store unless I really have to. Most of the time I'm comfortable fixing things on my own.
The second issue is that when I reboot after shutting down the computer with the power button, it does not always load the startup disk. Sometimes I get the recovery system instead, and if I try disk repair, restore from backup, or the startup disk option from the apple menu, it cannot locate the startup disk. Usually after a few tries, I can restart it and get my desktop, but I'm not sure how long that will work. I hoped that resetting the NVRAM would take care of this but it has not fixed the issue. When I do disk repair, it says the drive is fine. I've also used idefrag to clean up the drive. I'm thinking my hard drive might be about to die and I should just get a new one, but I don't want to spend the money if that is not the issue. I have 83 GB free on the drive so space should not be an issue.
Any suggestions on fixing either or both of these issue would be very much welcome! I need to make this computer last at least a couple more years.
Specs:
Mac Pro early 2008
Processor 2 x 2.8 GHz Quad-Core Intel Xeon
Memory 8 GB 800 MHz DDR2 FB-DIMM
Graphics NVIDIA GeForce 8800 GT 512 MB
Software OS X 10.8.5 (12F37)

Back up all data immediately as your boot drive may be failing.
If you have more than one user account, these instructions must be carried out as an administrator. I've tested them only with the Safari web browser. If you use another browser, they may not work as described.
Triple-click anywhere in the line below on this page to select it:
syslog -k Sender kernel -k Message CReq 'Channel t|GPU D|I/O|n Cause: -' | tail | open -ef
Copy the selected text to the Clipboard (command-C).
Launch the Terminal application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Terminal in the icon grid.
Paste into the Terminal window (command-V).
The command may take a noticeable amount of time to run. Wait for a new line ending in a dollar sign (“$”) to appear.
A TextEdit window will open with the output of the command. Normally the command will produce no output, and the window will be empty. If the TextEdit window (not the Terminal window) has anything in it, post it — the text, please, not a screenshot. The title of the TextEdit window doesn't matter, and you don't need to post that.

Mac Pro (Early 2008) - Question about swtiching startup hardrive

I have a Mac Pro (Early 2008), let's call her A, that I have been using non-stop but both its video card and a set of memory sticks have failed. My buddy bought his Mac Pro at the same time, let's call her B, but he barely used it. I want to keep on using a Mac Pro so I bought my friend's machine B, with the intention of using some of its parts or even use it as is, because as I mentioned, he barely used it throughout these years and is working fine.
Would it be possible to take the start up hard drive from A and place it on B? Like I said, they are both from the same generation and share pretty much the same configuration, except B, my friend's, came with a better video card (he ordered it that way).
Thank you so much for your help on this matter,
Juan.

Hello The hatter,
Please let me know what to do?
I decided to go for option B and now I am running my friends Mac Pro. Uploaded all my software and and back to work. Only that I noticed that this machine now stalls a bit at start up (gray logo, no spinning wheel for a while).
I discovered that even though I installed a new set of memory sticks, now the machine only recognizes Riser A (Top?) with 2GB (1GB x2) and listed as EMPTY the Riser B (Bottom?). I know they are supposed to go in pairs...so I am so tired of dealing with so many issues and worries with so much work to get done.
I decided to order a new set from OWC of matching (hopefully) sticks to place them on the Riser B (Bottom?) ASAP and see what happens?
What do you think?
Help please, I have been following your posts because I can tell you are extremely experience on the matter and I need such help more than ever before.
Thanks a million!
Juan

Mac Pro Early 2008 Crash on Boot Up

I have a Mac Pro early 2008 running OSX 10.8.5, and yesterday morning for seemingly no reason I had a screen corruption and freeze up, a kernel panic and then it rebooted itself. I have tried all of the memory( no flashing LED over power switch), cleared and reset all of the PRAM via keyboard and motherboard etc etc and everytime I reboot it crashes at the same point with a screen corruption and reboot. When I tried to boot in safe mode it the bar got 50% of the way across and it rebooted. I booted in verbose mode and single user mode and on both the last entry related to 'Ambrosiaaudiosupport' (as best I can remember) before it rebooted itself again. I sent the Kernel Panic to Apple but as I cannot get back into the OS I cannot obtain another.
Is there a solution to this please, and if so what do I need to do to rectify it
Many thanks in advance
Alan

If you can't boot in the usual way, try a safe boot. During startup, you’ll see a progress bar, and then the login screen, which appears even if you normally log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin. If you have more than one user account, you must be logged in as an administrator to carry out these instructions. Safe mode is slower than normal, and some things won’t work at all. Note: If FileVault is enabled on some models, or if a firmware password is set, or if the startup volume is on a software RAID, you can’t boot in safe mode. If you're able to boot, launch the Console application in any of the following ways: ☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.) ☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens. ☞ Open LaunchPad. Click Utilities, then Console in the icon grid. Select the most recent panic log under the heading System Diagnostic Reports on the left. If you don't see that heading, select View ▹ Show Log List from the menu bar. Post the entire contents of the panic report — the text, please, not a screenshot. In the interest of privacy, I suggest you edit out the “Anonymous UUID,” a long string of letters, numbers, and dashes in the header and body of the report, if it’s present (it may not be.) Please don't post shutdownStall, spin, or hang reports.

Upgrade boot drive in MAC PRO Early 2008 to SSD

Looking to upgrade my boot drive on Mac Pro Early 2008.
Possibly with SSD, but wasnt sure of compatibility. Also, is it a huge sacrafice in storage?
I'd appreciate any assistance.
Thank you!!!
Lyle

Establish a Boot Drive on the fast SSD, and move all User files off to other drives. These articles may help:
Japamac's Blog: Make space for performance -- Moving the Home Folder
http://chris.pirillo.com/how-to-move-the-home-folder-in-os-x-and-why/
OSX Tips: Setting-up a new Mac from an old one or its Backups
Transferring Home Folders not on a Startup volume
be sure to heed Pondini's warning:
If you do put home folders on a separate volume, it's strongly recommended that an Admin account and its home folder remain on the Startup volume. If there isn't one, and you have a problem with the separate home folder volume, you cannot log on to your Mac! And in some cases it will greatly complicatetransferring to a new Mac.
So if you're transferring from an available Mac that doesn't have an Admin account on its Startup volume, create one via System Preferences > Accounts before starting.
I have created a new User Tip with this information in it:
User Tip: Creating a lean, fast Boot Drive

Mac Pro (Early 2008) shuts down unexpectedly

I have a recurring problem with my Mac Pro (Early 2008). I put the computer to sleep; then, when I tap a few keys on the keyboard to wake it up, I hear the start-up sound and it boots up as if it were shut down.
This is particularly strange, because I do not have to use the "power" button on the tower to turn it on. When I tap the keys on the keyboard, as if to wake it from sleep, it makes the start-up sound and boots. I am guessing that somehow it is shutting off when I first try to wake it from sleep, and then must re-boot. But this is odd behavior that I've never seen from any Mac, and I've been using them for almost 20 years.
Any ideas? I'm going to call Apple Support but I always dread those long wait times and often fruitless conversations. I did not migrate information from my previous system; I took the time to manually migrate my files and reinstalled all apps from DVD specifically to avoid problems like this. Very frustrating.

I've noticed the same problem for one day with my new MP 2.8 dualquad, got a reboot after every sleep.
This solved the issue for me:
• Reset the PRAM (Boot the machine and hold ALTCOMMAND+PR for 3 startup gongs)
• Reset the SMC -> http://docs.info.apple.com/article.html?artnum=304123-en
Good luck

Mac Pro (early 2008) keyboard stops working

My Mac Pro (early 2008) has the Apple USB extended keyboard go no ops after the computer has been on for a while. This has been happening for quite a while and began shortly after I installed 10.6. It seemed to disappear for a while after 10.6.6 showed up but has returned since 10.6.8 has arrived. It seems to happen only when the computer goes to sleep but it does not happen every time. But it does happen most times. It appears that all USB ports on the back of my Apple monitor become unusable when this happens.
Anyone have any ideas? This has the feel of the sleep issue this model had with an early OS a few years ago.
MacPro3,1, 10.6.8, 32 GB RAM, dual 32 GHz quad-core Xeon chips, 4 bays populated, 1 TB, 2 TB, 2 TB, 2 TB

Scott..
Try a Safe Mode boot...
Startup your Mac in Safe Mode
A Safe Mode boot takes a longer than a normal boot so be patient.
Once you are in Safe Mode, click Restart from the Apple () menu.
Then try the keyboard.
A Safe Mode deletes some system caches that may help, especially after an update.

Mac Pro Early 2008 will not boot off Win7 Install DVD

Hello,
I am hoping someone out there will have encountered something similar and have some suggestions or ideas, because at this point I can't think of anything else to try.
I have a 2.8 Ghz 8-core Mac Pro (Early 2008) with an Nvidia 8800GT Graphics card. I am running OS 10.6.2, fully patched and updated.
I am attempting to install Windows 7 Ultimate via Boot Camp, and am encountering a rather odd problem.
Once I have launched Boot Camp Assistant it allows me to partition the drive and does so correctly, but when it attempts to reboot off the Windows 7 installation DVD, I encounter a blank grey-white screen similar to that which you normally get on startup but without the Apple logo. This continues for some time (it seems to vary), and then the screen goes dark and the monitor says it is receiving no signal. The fans on the Mac Pro go for a while, then it goes to sleep. I've tried leaving it for a couple hours, no dice.
I've tried both the 32-bit and 64-bit Windows install disks. I had the release candidate for Windows 7 installed previously, and it worked perfectly. I have since tried that same install DVD that I used to install the release candidate, and it encounters the exact same issue. Booting up off the Snow Leopard Install DVD works fine.
I tried doing a clean install of Snow Leopard on a spare drive, booting off that, and then starting from square 1 using Boot Camp Assistant to re-partition that same drive. Same problem. No matter what I do or try, my Mac Pro does not want to boot off this install disc. I have yet to try the disc in another machine to see if it works there, and I will as soon as I can, but the fact that the RC disc worked a few months back and now will not seems to rule out the boot discs as defective. I've also tried both my internal optical drives with no change, and no other discs have any issues.
I've already spent an hour and a half talking to Apple Technical Support, and they seemed stumped, so I'm hoping someone will have a notion. If not, I understand and appreciate you taking the time to read this- I have no idea at this point, and I'm generally a pretty knowledgeable user.
- Andrew

Thank you for your reply,
Pull all the drives you have other than the one that you will install Windows 7 to.
I think I will try this next.
Don't put Windows 7 on the same drive as OS X, give it its own.
That was initially what I started out doing.
And you don't even need Boot Camp Assistant.
True, but it's what Apple suggests using.
Might also want to try moving the monitor cable to the other card port.
Hmm, I think I'll try that.
Any other PCI cards or devices attached or installed should also be questioned or disconnected.
I've disconnected everything I could.
Always a good idea to start fresh which I assume you are doing (not trying to upgrade over RC etc).
Yes, the drive was empty to start with.
Honestly it seems like the Mac Pro is generally refusing to boot from any Windows disc. Things I've tried since my initial post:
- Loaded Windows 7 Install disc into my room mate's windows PC... loaded up fine, got to install screen
- Tried his OEM copy of Windows Vista 32-bit, same issue
At this point it seems like maybe some kind of firmware issue or some kind or graphics driver issue, but I'm pretty much grasping at straws at this point. It doesn't seem like it's even getting to the point where hard drives or anything matters.
It does recognize that I have a Windows 7 install disc inserted when I use the boot selector/startup disk chooser.
Thanks for the ideas, I'll try those out and see if any of them help,
-Andrew

Mac Pro (early 2008) No chime, pixelated white apple screen

My Mac Pro (early 2008) stopped working this morning. It was working fine yesterday, but did not start today.
i Press the power button, and there is no chime. The fan whirls around and the cd disc drive makes a noise. The startup screen shows up with Pixelated black bars across the whole screen.
this his stays onscreen, freezes for a few minutes, then restarts And continues the cycle of freezing and restarting.
iI've tried to reset the smc and pram and that hasn't done anything.
i've cleaned the inside of the computer, checked the RAM and graphics card, they seem to be in good working order.
does anyone know what's wrong with it?

Hi BDAqua
i tried safe boot. The white apple screen still comes up pixelated but with a grey loading bar at the bottom. Once the bar has loaded fully, nothing happens. it stays frozen on that screen until I have to force it to shutdown by pressing and holding the power button on the front of the tower.
i Tried holding the alt key. It brings up the devices, the screen is still pixelated. Pressing either one of the disk drives, didn't do anything new Unfortunately.
https://mobile.twitter.com/SundeepToor/status/559966340883415040/photos
hopefully you can see what my screen looks like in the link.

Mac Pro Early 2008 not booting

Hey guys!
I walked into a problem with a Mac Pro early 2008 model.
I got this Mac Pro from somebody since it wasn't working anymore. I was told there could be a graphic card (Nvidia) issue which I think should at least be correct but I am also having trouble with loading EFI. The following things happen:
When I turn on the mac using a DVI to VGA adapter i have no screen at all. (I don't have any other options atm)
There is no HD inserted.
PRAM and SMC reset won't do anything, i'm not even sure it reads keyboard commands.
The fans all work even the one on the GPU.
Front LED just burns steady.
No lights on my USB (non Apple) Keyboard turn on.
The lights of the mouse just flashes on start up.
RAM LEDS light up on startup.
Motherboard reset button doesn't make anything change.
When I Press the button for the diag LED's, the Trickle Power and the Good Power led come on, the GPU LED stays off. The EFI LED is off aswel.
No RAM errors show up. Tried switching RAM and disconnecting RAM and GPU.
No startup chime what so ever.
I figured there could be something wrong with the EFI firmware (or logic board is just broken). I am trying to restore the firmware with a firmware restoration cd, but I can't get the cd tray to open. I pressed the on button and kept pressing it for a long time. All it does is makes my status LED flash a couple of times real fast, but then it goes back to normal state. No cd tray is opening and its not flashing 3 times fast, 3 time slow, 3 times fast as it probely should be doing.
You guys have any idea what to try next or how to restore the firmware?
Thanks in advance.

there's a boot code to run with the older machines
Pike wrote this code
Using this code will get you around the efi/boot issue and move on to OS 10.10.02
Installing Yosemite just prior to entering the efi/boot, then restart twice.
You'll need to research Pike's code, but your 2006 to 2008 machines are long ways from trash.
I'm upgrading my 2006 to 8 cores, Yosemite and 32 gig of ram.
Long live these early Mac Pros
https://www.google.com/url?sa=t&rct=j&q=&esrc=s&source=web&cd=1&cad=rja&uact=8&v ed=0CB8QFjAA&url=http%3A%2F%2Fforums.mac…
maybe your issue is not related

Mac Pro (early 2008) black screen after 2015-004 Mavericks security update

Hi,
My Mac Pro (early 2008) does not start up after 2015-004 security update last week. I can't
get anything on my monitors. I can hear it starts booting, but not sure if does so fully, because the screen
stays black. Have tried all the different booting options, e.g. safe boot, but no effect. Is there a way to revert
the update or even do a clean OS install, even if I can't see anything on the monitor?
I just noticed that Apple has released a supplemental update today for Yosemite 10.10.3,
"that will fix video driver issuesthat will prevent your mac from starting up when running certain apps that capture video"
I am wondering if this is my problem, even if I use Mavericks. Any thoughts?

Try booting to Recovery and repairing the the startup disk via Disk Utility.
OS X: About OS X Recovery - Apple Support
Next try resinstalling the OS
OS X Mavericks: Reinstall OS X

What's the best graphic card for FCP X and a Mac Pro (early) 2008?

I have a Radeon HD 3870 in my Mac Pro, it seems that I cannot use this configuration with Final Cut Pro X. Then what's the best graphic card for FCP X usable in a Mac Pro (early) 2008?
Thx,
Phil

You can get a 5770 radeon ATI MAC card
Avoid the 5770 cards on ebay and Amazon - many are black market or manipulated cards.
Buy it from Apple online store or B&H photo or Macconection
And in my case, I was able to sell my old 2600 XT card on ebay for $65 and put that money toward a 5770 card (Which was about $230 minus the $65)
I installed the 5770 in my early Mac Pro 2 x 2.8 and it works great

Mac Pro Early 2008 - random reboots!

Hello!
I have a problem with my Mac Pro Early 2008...
Processor 2 x 2.8 GHz Quad-Core Intel Xeon
Memory 10 GB 800 MHz DDR2 FB-DIMM
Graphics NVIDIA GeForce 8800 GT 512 MB
Software OS X 10.8.4 (12E55)
...ther screen will break up into random blocky pattern (like the video card freezes) and the Mac will reboot, kernel panic basically...
...3 months ago i updated the RAM from 6gb to 10gb, but haven't done anything else to the **** thing.
...it's done it five times in the last two days now.
...here is my lates panic report...this happened 10 minutes ago.
...does this report make sense to anyone?
===================================
Interval Since Last Panic Report: 1997046 sec
Panics Since Last Report:          3
Anonymous UUID:                    E39A1BFB-D1E1-D614-7991-B49386694DC1
Wed Jul 24 16:56:33 2013
panic(cpu 1 caller 0xffffff801669e53b): "TLB invalidation IPI timeout: " "CPU(s) failed to respond to interrupts, unresponsive CPU bitmap: 0x4, NMIPI acks: orig: 0x0, now: 0x0"@/SourceCache/xnu/xnu-2050.24.15/osfmk/x86_64/pmap.c:2337
Backtrace (CPU 1), Frame : Return Address
0xffffff813feeb960 : 0xffffff801661d626
0xffffff813feeb9d0 : 0xffffff801669e53b
0xffffff813feeba50 : 0xffffff80166a3a3a
0xffffff813feebae0 : 0xffffff80166a53a6
0xffffff813feebb00 : 0xffffff8016664406
0xffffff813feebbf0 : 0xffffff801666706c
0xffffff813feebce0 : 0xffffff801666b0e0
0xffffff813feebd10 : 0xffffff8016665bdf
0xffffff813feebd40 : 0xffffff8016717554
0xffffff813feebd70 : 0xffffff80167197c3
0xffffff813feebdc0 : 0xffffff801691184f
0xffffff813feebdf0 : 0xffffff80169062e6
0xffffff813feebea0 : 0xffffff80166fa0af
0xffffff813feebed0 : 0xffffff80166f37a7
0xffffff813feebf30 : 0xffffff80166fa029
0xffffff813feebf50 : 0xffffff80169e16aa
0xffffff813feebfb0 : 0xffffff80166ce9c3
BSD process name corresponding to current thread: launchd
Mac OS version:
12E55
Kernel version:
Darwin Kernel Version 12.4.0: Wed May 1 17:57:12 PDT 2013; root:xnu-2050.24.15~1/RELEASE_X86_64
Kernel UUID: 896CB1E3-AB79-3DF1-B595-549DFFDF3D36
Kernel slide:     0x0000000016400000
Kernel text base: 0xffffff8016600000
System model name: MacPro3,1 (Mac-F42C88C8)
System uptime in nanoseconds: 14846309182590
last loaded kext at 3120916610267: com.apple.filesystems.smbfs    1.8.4 (addr 0xffffff7f98562000, size 229376)
last unloaded kext at 410364773343: com.apple.driver.StorageLynx    3.1.7 (addr 0xffffff7f9853e000, size 8192)
loaded kexts:
com.Logitech.Control Center.HID Driver    3.6.0
com.metakine.handsoff.driver    2.0.8
com.apple.filesystems.smbfs    1.8.4
com.apple.driver.Oxford_Semi    3.1.7
com.apple.driver.AppleHWSensor    1.9.5d0
com.apple.driver.AudioAUUC    1.60
com.apple.filesystems.autofs    3.0
com.apple.driver.AppleUpstreamUserClient    3.5.10
com.apple.driver.AppleHDA    2.3.7fc4
com.apple.driver.AppleMCCSControl    1.1.11
com.apple.iokit.CSRBluetoothHCIControllerUSBTransport    4.1.4f2
com.apple.GeForce    8.1.2
com.apple.iokit.IOUserEthernet    1.0.0d1
com.apple.iokit.IOBluetoothSerialManager    4.1.4f2
com.apple.driver.AppleLPC    1.6.0
com.apple.Dont_Steal_Mac_OS_X    7.0.0
com.apple.driver.AppleMCEDriver    1.1.9
com.apple.driver.ApplePolicyControl    3.4.5
com.apple.driver.ACPI_SMC_PlatformPlugin    1.0.0
com.apple.iokit.SCSITaskUserClient    3.5.5
com.apple.driver.XsanFilter    404
com.apple.iokit.IOAHCIBlockStorage    2.3.1
com.apple.driver.AppleIntel8254XEthernet    3.1.1b1
com.apple.driver.AppleUSBHub    5.5.5
com.apple.driver.AppleFWOHCI    4.9.6
com.apple.AppleFSCompression.AppleFSCompressionTypeDataless    1.0.0d1
com.apple.AppleFSCompression.AppleFSCompressionTypeZlib    1.0.0d1
com.apple.BootCache    34
com.apple.driver.AppleAHCIPort    2.5.2
com.apple.driver.AppleIntelPIIXATA    2.5.1
com.apple.driver.AppleUSBEHCI    5.5.0
com.apple.driver.AppleUSBUHCI    5.2.5
com.apple.driver.AppleEFINVRAM    1.7
com.apple.driver.AppleACPIButtons    1.7
com.apple.driver.AppleRTC    1.5
com.apple.driver.AppleHPET    1.8
com.apple.driver.AppleSMBIOS    1.9
com.apple.driver.AppleACPIEC    1.7
com.apple.driver.AppleAPIC    1.6
com.apple.driver.AppleIntelCPUPowerManagementClient    196.0.0
com.apple.nke.applicationfirewall    4.0.39
com.apple.security.quarantine    2.1
com.apple.driver.AppleIntelCPUPowerManagement    196.0.0
com.apple.iokit.IOSCSIBlockCommandsDevice    3.5.5
com.apple.iokit.IOFireWireSerialBusProtocolTransport    2.1.1
com.apple.iokit.IOFireWireSBP2    4.2.2
com.apple.kext.triggers    1.0
com.apple.driver.DspFuncLib    2.3.7fc4
com.apple.iokit.IOAudioFamily    1.8.9fc11
com.apple.kext.OSvKernDSPLib    1.6
com.apple.driver.AppleSMBusController    1.0.11d0
com.apple.nvidia.nv50hal    8.1.2
com.apple.NVDAResman    8.1.2
com.apple.iokit.IOSurface    86.0.4
com.apple.iokit.AppleBluetoothHCIControllerUSBTransport    4.1.4f2
com.apple.iokit.IOSerialFamily    10.0.6
com.apple.driver.AppleHDAController    2.3.7fc4
com.apple.iokit.IOHDAFamily    2.3.7fc4
com.apple.iokit.IOFireWireIP    2.2.5
com.apple.driver.AppleGraphicsControl    3.4.5
com.apple.iokit.IONDRVSupport    2.3.7
com.apple.iokit.IOGraphicsFamily    2.3.7
com.apple.driver.AppleSMC    3.1.4d2
com.apple.driver.IOPlatformPluginLegacy    1.0.0
com.apple.driver.IOPlatformPluginFamily    5.3.0d51
com.apple.driver.AppleUSBHIDKeyboard    170.2
com.apple.driver.AppleHIDKeyboard    170.2
com.apple.driver.IOBluetoothHIDDriver    4.1.4f2
com.apple.iokit.IOBluetoothFamily    4.1.4f2
com.apple.iokit.IOUSBHIDDriver    5.2.5
com.apple.driver.AppleUSBMergeNub    5.5.5
com.apple.driver.AppleUSBComposite    5.2.5
com.apple.iokit.IOSCSIMultimediaCommandsDevice    3.5.5
com.apple.iokit.IOBDStorageFamily    1.7
com.apple.iokit.IODVDStorageFamily    1.7.1
com.apple.iokit.IOCDStorageFamily    1.7.1
com.apple.iokit.IOATAPIProtocolTransport    3.5.0
com.apple.iokit.IOSCSIArchitectureModelFamily    3.5.5
com.apple.iokit.IOUSBUserClient    5.5.5
com.apple.iokit.IOFireWireFamily    4.5.5
com.apple.iokit.IONetworkingFamily    3.0
com.apple.iokit.IOAHCIFamily    2.3.1
com.apple.iokit.IOATAFamily    2.5.1
com.apple.iokit.IOUSBFamily    5.6.0
com.apple.iokit.IOHIDFamily    1.8.1
com.apple.driver.AppleEFIRuntime    1.7
com.apple.iokit.IOSMBusFamily    1.1
com.apple.security.sandbox    220.3
com.apple.kext.AppleMatch    1.0.0d1
com.apple.security.TMSafetyNet    7
com.apple.driver.DiskImages    345
com.apple.iokit.IOStorageFamily    1.8
com.apple.driver.AppleKeyStore    28.21
com.apple.driver.AppleACPIPlatform    1.7
com.apple.iokit.IOPCIFamily    2.7.3
com.apple.iokit.IOACPIFamily    1.4
com.apple.kec.corecrypto    1.0
System Profile:
Model: MacPro3,1, BootROM MP31.006C.B05, 8 processors, Quad-Core Intel Xeon, 2.8 GHz, 10 GB, SMC 1.25f4
Graphics: NVIDIA GeForce 8800 GT, NVIDIA GeForce 8800 GT, PCIe, 512 MB
Memory Module: DIMM Riser B/DIMM 1, 2 GB, DDR2 FB-DIMM, 800 MHz, 0x0D9B, 0x000000000000000000000000000000000000
Memory Module: DIMM Riser B/DIMM 2, 2 GB, DDR2 FB-DIMM, 800 MHz, 0x0D9B, 0x000000000000000000000000000000000000
Memory Module: DIMM Riser A/DIMM 1, 2 GB, DDR2 FB-DIMM, 800 MHz, 0x802C, 0x3138484632353637324A4438304545314434
Memory Module: DIMM Riser A/DIMM 2, 2 GB, DDR2 FB-DIMM, 800 MHz, 0x802C, 0x3138484632353637324A4438304545314434
Memory Module: DIMM Riser A/DIMM 3, 1 GB, DDR2 FB-DIMM, 800 MHz, 0x80AD, 0x48594D5035313241373243503844332D5335
Memory Module: DIMM Riser A/DIMM 4, 1 GB, DDR2 FB-DIMM, 800 MHz, 0x80AD, 0x48594D5035313241373243503844332D5335
Bluetooth: Version 4.1.4f2 12041, 2 service, 18 devices, 1 incoming serial ports
Network Service: Ethernet 1, Ethernet, en0
PCI Card: NVIDIA GeForce 8800 GT, sppci_displaycontroller, Slot-1
Serial ATA Device: ST3500630AS P, 500.11 GB
Parallel ATA Device: PIONEER DVD-RW DVR-112D
USB Device: hub_device, 0x0409 (NEC Corporation), 0x005a, 0xfd400000 / 2
USB Device: Keyboard Hub, apple_vendor_id, 0x1006, 0xfd410000 / 4
USB Device: USB Laser Mouse, 0x046d (Logitech Inc.), 0xc069, 0xfd413000 / 6
USB Device: Apple Keyboard, apple_vendor_id, 0x0221, 0xfd412000 / 5
USB Device: EIZO USB HID Monitor, 0x056d (Eizo), 0x0002, 0xfd430000 / 3
USB Device: Bluetooth USB Host Controller, apple_vendor_id, 0x8206, 0x5d200000 / 2
FireWire Device: built-in_hub, 800mbit_speed
FireWire Device: OEM ATA Device 00, G-TECH, 800mbit_speed
==============================

...and this is my report from yesterday when it last happened to me...
==============================
Tue Jul 23 22:05:20 2013
panic(cpu 5 caller 0xffffff80156b8655): Kernel trap at 0xffffff7f96aed154, type 14=page fault, registers:
CR0: 0x0000000080010033, CR2: 0x0000000000000010, CR3: 0x00000000238e8000, CR4: 0x0000000000000660
RAX: 0x0000000000000001, RBX: 0xffffff811be18000, RCX: 0xffffff802e224e98, RDX: 0xffffff813df6ba38
RSP: 0xffffff813df6bb60, RBP: 0xffffff813df6bb60, RSI: 0x0000000000000000, RDI: 0x0000000000000000
R8: 0x0000000000000000, R9: 0x00000000000003ff, R10: 0xffffffffffffffff, R11: 0x00000000ffffffff
R12: 0xffffff811be18000, R13: 0x0000000000000000, R14: 0x0000000000000002, R15: 0x0000000000000000
RFL: 0x0000000000010246, RIP: 0xffffff7f96aed154, CS: 0x0000000000000008, SS: 0x0000000000000010
Fault CR2: 0x0000000000000010, Error code: 0x0000000000000000, Fault CPU: 0x5
Backtrace (CPU 5), Frame : Return Address
0xffffff813df6b800 : 0xffffff801561d626
0xffffff813df6b870 : 0xffffff80156b8655
0xffffff813df6ba40 : 0xffffff80156ce17d
0xffffff813df6ba60 : 0xffffff7f96aed154
0xffffff813df6bb60 : 0xffffff7f96ad6844
0xffffff813df6bbb0 : 0xffffff7f96ad679a
0xffffff813df6bbd0 : 0xffffff7f96ab228e
0xffffff813df6bc00 : 0xffffff7f95c913a0
0xffffff813df6bc40 : 0xffffff7f95c9130f
0xffffff813df6bc60 : 0xffffff7f95c9675c
0xffffff813df6bcf0 : 0xffffff7f95c8ee50
0xffffff813df6bd20 : 0xffffff7f95ce01cf
0xffffff813df6bd70 : 0xffffff8015a33efb
0xffffff813df6bdc0 : 0xffffff8015a65297
0xffffff813df6be30 : 0xffffff801569874f
0xffffff813df6be80 : 0xffffff8015620b3d
0xffffff813df6beb0 : 0xffffff8015610448
0xffffff813df6bf00 : 0xffffff801561961b
0xffffff813df6bf70 : 0xffffff80156a6536
0xffffff813df6bfb0 : 0xffffff80156ce9e3
      Kernel Extensions in backtrace:
         com.apple.iokit.IOGraphicsFamily(2.3.7)[990D1A42-DF16-3AB9-ABC1-6A88AC142244]@0 xffffff7f95c85000->0xffffff7f95cbcfff
            dependency: com.apple.iokit.IOPCIFamily(2.7.3)[1D668879-BEF8-3C58-ABFE-FAC6B3E9A292]@0xffff ff7f95c46000
         com.apple.NVDAResman(8.1.2)[96AE69DE-8A37-39D0-B2D3-D8446A6AA670]@0xffffff7f95c dc000->0xffffff7f95f81fff
            dependency: com.apple.iokit.IOPCIFamily(2.7.3)[1D668879-BEF8-3C58-ABFE-FAC6B3E9A292]@0xffff ff7f95c46000
            dependency: com.apple.iokit.IONDRVSupport(2.3.7)[6C8CFC18-75F0-3DEF-86C7-CEB2C1FD6BB1]@0xff ffff7f95cc8000
            dependency: com.apple.iokit.IOGraphicsFamily(2.3.7)[990D1A42-DF16-3AB9-ABC1-6A88AC142244]@0 xffffff7f95c85000
         com.apple.GeForce(8.1.2)[7EC545A4-4B57-32F1-8DC3-C31023AFBDCB]@0xffffff7f96aae0 00->0xffffff7f96b7bfff
            dependency: com.apple.NVDAResman(8.1.2)[96AE69DE-8A37-39D0-B2D3-D8446A6AA670]@0xffffff7f95c dc000
            dependency: com.apple.iokit.IONDRVSupport(2.3.7)[6C8CFC18-75F0-3DEF-86C7-CEB2C1FD6BB1]@0xff ffff7f95cc8000
            dependency: com.apple.iokit.IOPCIFamily(2.7.3)[1D668879-BEF8-3C58-ABFE-FAC6B3E9A292]@0xffff ff7f95c46000
            dependency: com.apple.iokit.IOGraphicsFamily(2.3.7)[990D1A42-DF16-3AB9-ABC1-6A88AC142244]@0 xffffff7f95c85000
BSD process name corresponding to current thread: WindowServer
Mac OS version:
12E55
Kernel version:
Darwin Kernel Version 12.4.0: Wed May 1 17:57:12 PDT 2013; root:xnu-2050.24.15~1/RELEASE_X86_64
Kernel UUID: 896CB1E3-AB79-3DF1-B595-549DFFDF3D36
Kernel slide:     0x0000000015400000
Kernel text base: 0xffffff8015600000
System model name: MacPro3,1 (Mac-F42C88C8)
System uptime in nanoseconds: 43990035275
last loaded kext at 33162859687: com.apple.driver.AudioAUUC    1.60 (addr 0xffffff7f96d60000, size 32768)
loaded kexts:
com.Logitech.Control Center.HID Driver    3.6.0
com.metakine.handsoff.driver    2.0.8
com.apple.driver.AudioAUUC    1.60
com.apple.iokit.IOBluetoothSerialManager    4.1.4f2
com.apple.driver.AppleTyMCEDriver    1.0.2d2
com.apple.driver.AppleHDAHardwareConfigDriver    2.3.7fc4
com.apple.driver.AppleHDA    2.3.7fc4
com.apple.driver.AppleUpstreamUserClient    3.5.10
com.apple.driver.AppleMCCSControl    1.1.11
com.apple.filesystems.autofs    3.0
com.apple.iokit.IOUserEthernet    1.0.0d1
com.apple.GeForce    8.1.2
com.apple.iokit.CSRBluetoothHCIControllerUSBTransport    4.1.4f2
com.apple.Dont_Steal_Mac_OS_X    7.0.0
com.apple.driver.ApplePolicyControl    3.4.5
com.apple.nvidia.NVDAStartup    8.1.2
com.apple.driver.AppleMCEDriver    1.1.9
com.apple.driver.AppleLPC    1.6.0
com.apple.driver.ACPI_SMC_PlatformPlugin    1.0.0
com.apple.driver.CSRHIDTransitionDriver    4.1.4f2
com.apple.driver.AppleFireWireStorage    3.1.7
com.apple.driver.initioFWBridge    3.1.7
com.apple.driver.IOFireWireSerialBusProtocolSansPhysicalUnit    3.1.7
com.apple.driver.LSI_FW_500    3.1.7
com.apple.driver.Oxford_Semi    3.1.7
com.apple.driver.StorageLynx    3.1.7
com.apple.driver.PioneerSuperDrive    3.1.7
com.apple.iokit.SCSITaskUserClient    3.5.5
com.apple.driver.XsanFilter    404
com.apple.driver.AppleFileSystemDriver    3.0.1
com.apple.AppleFSCompression.AppleFSCompressionTypeDataless    1.0.0d1
com.apple.AppleFSCompression.AppleFSCompressionTypeZlib    1.0.0d1
com.apple.BootCache    34
com.apple.iokit.IOAHCIBlockStorage    2.3.1
com.apple.driver.AppleUSBHub    5.5.5
com.apple.driver.AppleIntel8254XEthernet    3.1.1b1
com.apple.driver.AppleFWOHCI    4.9.6
com.apple.driver.AppleAHCIPort    2.5.2
com.apple.driver.AppleIntelPIIXATA    2.5.1
com.apple.driver.AppleUSBEHCI    5.5.0
com.apple.driver.AppleUSBUHCI    5.2.5
com.apple.driver.AppleEFINVRAM    1.7
com.apple.driver.AppleACPIButtons    1.7
com.apple.driver.AppleRTC    1.5
com.apple.driver.AppleHPET    1.8
com.apple.driver.AppleSMBIOS    1.9
com.apple.driver.AppleACPIEC    1.7
com.apple.driver.AppleAPIC    1.6
com.apple.driver.AppleIntelCPUPowerManagementClient    196.0.0
com.apple.nke.applicationfirewall    4.0.39
com.apple.security.quarantine    2.1
com.apple.driver.AppleIntelCPUPowerManagement    196.0.0
com.apple.iokit.IOSerialFamily    10.0.6
com.apple.driver.DspFuncLib    2.3.7fc4
com.apple.iokit.IOAudioFamily    1.8.9fc11
com.apple.kext.OSvKernDSPLib    1.6
com.apple.driver.AppleSMBusController    1.0.11d0
com.apple.kext.triggers    1.0
com.apple.nvidia.nv50hal    8.1.2
com.apple.NVDAResman    8.1.2
com.apple.iokit.IOSurface    86.0.4
com.apple.iokit.AppleBluetoothHCIControllerUSBTransport    4.1.4f2
com.apple.driver.AppleHDAController    2.3.7fc4
com.apple.iokit.IOHDAFamily    2.3.7fc4
com.apple.driver.AppleGraphicsControl    3.4.5
com.apple.iokit.IONDRVSupport    2.3.7
com.apple.iokit.IOGraphicsFamily    2.3.7
com.apple.iokit.IOFireWireIP    2.2.5
com.apple.driver.AppleSMBusPCI    1.0.11d0
com.apple.driver.AppleSMC    3.1.4d2
com.apple.driver.IOPlatformPluginLegacy    1.0.0
com.apple.driver.IOPlatformPluginFamily    5.3.0d51
com.apple.iokit.IOSCSIBlockCommandsDevice    3.5.5
com.apple.driver.AppleUSBHIDKeyboard    170.2
com.apple.driver.AppleHIDKeyboard    170.2
com.apple.driver.IOBluetoothHIDDriver    4.1.4f2
com.apple.iokit.IOBluetoothFamily    4.1.4f2
com.apple.iokit.IOUSBHIDDriver    5.2.5
com.apple.iokit.IOFireWireSerialBusProtocolTransport    2.1.1
com.apple.iokit.IOFireWireSBP2    4.2.2
com.apple.driver.AppleUSBMergeNub    5.5.5
com.apple.driver.AppleUSBComposite    5.2.5
com.apple.iokit.IOSCSIMultimediaCommandsDevice    3.5.5
com.apple.iokit.IOBDStorageFamily    1.7
com.apple.iokit.IODVDStorageFamily    1.7.1
com.apple.iokit.IOCDStorageFamily    1.7.1
com.apple.iokit.IOATAPIProtocolTransport    3.5.0
com.apple.iokit.IOSCSIArchitectureModelFamily    3.5.5
com.apple.iokit.IONetworkingFamily    3.0
com.apple.iokit.IOUSBUserClient    5.5.5
com.apple.iokit.IOFireWireFamily    4.5.5
com.apple.iokit.IOAHCIFamily    2.3.1
com.apple.iokit.IOATAFamily    2.5.1
com.apple.iokit.IOUSBFamily    5.6.0
com.apple.iokit.IOHIDFamily    1.8.1
com.apple.driver.AppleEFIRuntime    1.7
com.apple.iokit.IOSMBusFamily    1.1
com.apple.security.sandbox    220.3
com.apple.kext.AppleMatch    1.0.0d1
com.apple.security.TMSafetyNet    7
com.apple.driver.DiskImages    345
com.apple.iokit.IOStorageFamily    1.8
com.apple.driver.AppleKeyStore    28.21
com.apple.driver.AppleACPIPlatform    1.7
com.apple.iokit.IOPCIFamily    2.7.3
com.apple.iokit.IOACPIFamily    1.4
com.apple.kec.corecrypto    1.0
==============================

MAC PRO (Early 2008) RAID CARD ISSUE - SYSTEM FREEZEHello (hopefully someone can shed some light on my issue) I own as above a MAC PRO (Early 2008) this has a RAID card installed along with two 15k.7 cheetah hdd (320gb) and a spare drive, (which i m

Hello (hopefully someone can shed some light on my issue)
I own as above a MAC PRO (Early 2008) this has a RAID card installed along with two 15k.7 cheetah hdd (320gb) and a spare drive, (which i made a regular drive)
a while ago i had to replace the RAID card battery, so i did this, over a year later the same thing happened again, but as previous just left it and the system seemed fine for ages, until last night i was working in PHOTOSHOP and everything just froze and the screen kind of appeared GREEN, could not do a single thing. So restarted the mac, this time grey screen for ages and a message appeared, (macs version of blue screen) (see attached).
I restarted the machine and this time a flashing question mark folder!
could not do a thing.
so i found my copy of snow leopard and got the computer to run this and at least launch the DISK UTILITY and (Interestingly in the drop down menu RAID UTILITY was also in the menu) but it did not matter which utility i used the (RAID or DISK) neither could see any of drives, just the dvd drive.
so looked around on you tube and various forums and discovered if i take out the RAID CARD and re-plug the main lead from the RAID card back in to the LOGIC BOARD I would be reverting the MAC to a normal regular non-RAID computer.
After performing this HARDWARE task and inserting all three HDD, and running the DISK utility from the drop down menu via the SNOW LEOPARD disc.
(interestingly since the RAID card had been removed the RAID UTILITY from the drop down menu no longer appeared). running disk utility I can now only see the regular (spare) hdd and DVD Drive, but the two RAID HDD , again, still do not show up DISK UTILITY?
O.K. so i could chuck out the RAID card (AND RAID HDD) and just go with a regular set-up, and run a back restore from Time Machine on a NEW hdd purchased.
but what is wrong with the RAID, is the card at fault or are both HDD used for the RAID knackered? can i perform any tests, to see whats what?
thanks for your help in advanced.

hello people, the issue was in fact the GRAPHICS card nothing to do with the HDD or RAID system ( although this did cause issues with the RAID system it basically lost its way) below is my replay to another similar problem some one else had!
working in photoshop and then everything stopped working and the lot froze! only option was to force shutdown (via button).
and try to restart, hoping all was fine, this was not the case :-(
I had the added issue of the RAID card system, that i have, this was confused to say the lease and would not behave or work, causing the start up to hang.
so i thought the HDD must be bust and the root cause. ( but soon learnt it was not the cause )
...bought a new HDD removed the RAID card and replugged the cable from RAID card into LOGIC board, ( making the computer act like any normal non-RAID system). I managed to install the OSX, using the snow leopard disk way. once the mac was running, i started to notice the screen would flicker and started to see 'artefacts'. so i started to reveal my symptoms to the web and forums and soon discovered that my graphics card could be the issue all along?.
(nvidia geforce 8800gt 2x dvi).
I read up on that a fix, could be either A. reply the thermal paste, as the card could be over heating or B. stick the card in the oven trick.
Tried option A. first and nothing still issues, so last night took the plunge carried out option B. and ta da it worked! i even managed to run
from my new HDD my lasted install OS X, absolutely fine. I then thought, maybe i could repair my RAID so replugged all the HARDWARD back in and
carried out a disk repair and disk permissions on drives( took a small amount of time), via the SNOW LEOPARD disc - (Disk utilities) and this worked and now have my system working as it was just over 6 days ago.
what was the cost to get this? bought a new hdd so 40.00gbp and thermal paste and cleaner kit ( your still need to do this ) search video card trick on you tube.
and renew thermal paste, approx 15.00gbp, technically i don't need the new HDD, but it was all part of the trial and error way i went. ( i do have extra storage as a result!)"

Can't install montain lion, mavericks or yosemite on my mac pro early 2008 8core

I tried installing mountain lion mavericks and yosemite on my mac pro early 2008 I upgraded the video card to see if that was the problems and still the same the problem is that after installing even during install the mouse moves super slow and the keyboard won't work at all so I can't entern
any information this is with a clean install and even if I update lion it does the same everything works fine on lion 10.7.5 problems there does any one know what could be the issue here? I'm only running one monitor and its the 30 inch cinema display here are the specst of my machine excuse my grammar and spelling it was never my favorite subject
Model Name: Mac Pro
Model Identifier: MacPro3,1
Processor Name: Quad-Core Intel Xeon
Processor Speed: 2.8 GHz
Number of Processors: 2
Total Number of Cores: 8
L2 Cache (per Processor): 12 MB
Memory: 8 GB
Bus Speed: 1.6 GHz
Boot ROM Version: MP31.006C.B05
SMC Version (system): 1.25f4
Serial Number (system): G881111VXYK
Hardware UUID: 714C0BE4-9A35-5C33-BF74-0F55F7C31B5F
AMD Radeon HD 6870:
Chipset Model: AMD Radeon HD 6870
Type: GPU
Bus: PCIe
Slot: Slot-1
PCIe Lane Width: x16
VRAM (Total): 1024 MB
Vendor: ATI (0x1002)
Device ID: 0x6738
Revision ID: 0x0000
ROM Revision: 007-NETKAS-ORG
EFI Driver Version: 01.00.507
Displays:
Cinema HD:
Display Type: LCD
Resolution: 2560 x 1600
Pixel Depth: 32-Bit Color (ARGB8888)
Display Serial Number: CY03018WXMP
Main Display: Yes
Mirror: Off
Online: Yes
Rotation: Supported
ECC: Enabled
DIMM Riser B/DIMM 1:
Size: 2 GB
Type: DDR2 FB-DIMM
Speed: 667 MHz
Status: OK
Manufacturer: 0x014F
Part Number: 0x5453324741504D41435038502D5420202020
Serial Number: 0x00031CFB
DIMM Riser B/DIMM 2:
Size: 2 GB
Type: DDR2 FB-DIMM
Speed: 667 MHz
Status: OK
Manufacturer: 0x014F
Part Number: 0x5453324741504D41435038502D5420202020
Serial Number: 0x00031CFB
DIMM Riser A/DIMM 1:
Size: 1 GB
Type: DDR2 FB-DIMM
Speed: 667 MHz
Status: OK
Manufacturer: 0x80AD
Part Number: 0x48594D5035313241373243503844332D5335
Serial Number: 0x01431026
DIMM Riser A/DIMM 2:
Size: 1 GB
Type: DDR2 FB-DIMM
Speed: 667 MHz
Status: OK
Manufacturer: 0x80AD
Part Number: 0x48594D5035313241373243503844332D5935
Serial Number: 0x57656411
DIMM Riser B/DIMM 3:
Size: Empty
Type: Empty
Speed: Empty
Status: Empty
Manufacturer: Empty
Part Number: Empty
Serial Number: Empty
DIMM Riser B/DIMM 4:
Size: Empty
Type: Empty
Speed: Empty
Status: Empty
Manufacturer: Empty
Part Number: Empty
Serial Number: Empty
DIMM Riser A/DIMM 3:
Size: 1 GB
Type: DDR2 FB-DIMM
Speed: 667 MHz
Status: OK
Manufacturer: 0x80AD
Part Number: 0x48594D5035313241373243503844332D5335
Serial Number: 0x01172313
DIMM Riser A/DIMM 4:
Size: 1 GB
Type: DDR2 FB-DIMM
Speed: 667 MHz
Status: OK
Manufacturer: 0x80AD
Part Number: 0x48594D5035313241373243503844332D5335
Serial Number: 0x01172714
Intel ESB2 AHCI:
Vendor: Intel
Product: ESB2 AHCI
Link Speed: 3 Gigabit
Negotiated Link Speed: 3 Gigabit
Description: AHCI Version 1.10 Supported
WDC WD5000AAKS-00A7B0:
Capacity: 500.11 GB (500,107,862,016 bytes)
Model: WDC WD5000AAKS-00A7B0
Revision: 01.03B01
Serial Number:     WD-WMASY0158891
Native Command Queuing: Yes
Queue Depth: 32
Removable Media: No
Detachable Drive: No
BSD Name: disk2
Medium Type: Rotational
Bay Name: Bay 1
Partition Map Type: GPT (GUID Partition Table)
S.M.A.R.T. status: Verified
Volumes:
disk2s1:
Capacity: 209.7 MB (209,715,200 bytes)
BSD Name: disk2s1
Content: EFI
HD:
Capacity: 499.25 GB (499,248,103,424 bytes)
Available: 484.82 GB (484,820,348,928 bytes)
Writable: Yes
File System: Journaled HFS+
BSD Name: disk2s2
Mount Point: /Volumes/HD
Content: Apple_HFS
Recovery HD:
Capacity: 650 MB (650,002,432 bytes)
BSD Name: disk2s3
Content: Apple_Boot
WDC WD5000AAKS-00A7B0:
Capacity: 500.11 GB (500,107,862,016 bytes)
Model: WDC WD5000AAKS-00A7B0
Revision: 01.03B01
Serial Number:     WD-WMASY0158891
Native Command Queuing: Yes
Queue Depth: 32
Removable Media: No
Detachable Drive: No
BSD Name: disk2
Medium Type: Rotational
Bay Name: Bay 1
Partition Map Type: GPT (GUID Partition Table)
S.M.A.R.T. status: Verified
Volumes:
disk2s1:
Capacity: 209.7 MB (209,715,200 bytes)
BSD Name: disk2s1
Content: EFI
HD:
Capacity: 499.25 GB (499,248,103,424 bytes)
Available: 484.82 GB (484,820,348,928 bytes)
Writable: Yes
File System: Journaled HFS+
BSD Name: disk2s2
Mount Point: /Volumes/HD
Content: Apple_HFS
Recovery HD:
Capacity: 650 MB (650,002,432 bytes)
BSD Name: disk2s3
Content: Apple_Boot
Intel ESB2 AHCI:
Vendor: Intel
Product: ESB2 AHCI
Link Speed: 3 Gigabit
Negotiated Link Speed: 3 Gigabit
Description: AHCI Version 1.10 Supported
HDS725050KLA360:
Capacity: 500.11 GB (500,107,862,016 bytes)
Model: HDS725050KLA360
Revision: K2AOAB5A
Serial Number:       KRVN67ZBHBEEAH
Native Command Queuing: Yes
Queue Depth: 32
Removable Media: No
Detachable Drive: No
BSD Name: disk1
Medium Type: Rotational
Bay Name: Bay 2
Partition Map Type: MBR (Master Boot Record)
S.M.A.R.T. status: Verified
Volumes:
UNTITLED 1:
Capacity: 500.11 GB (500,107,860,992 bytes)
Available: 449.41 GB (449,412,988,928 bytes)
Writable: Yes
File System: MS-DOS FAT32
BSD Name: disk1s1
Mount Point: /Volumes/UNTITLED 1
Content: DOS_FAT_32
HDS725050KLA360:
Capacity: 500.11 GB (500,107,862,016 bytes)
Model: HDS725050KLA360
Revision: K2AOAB5A
Serial Number:       KRVN67ZBHBEEAH
Native Command Queuing: Yes
Queue Depth: 32
Removable Media: No
Detachable Drive: No
BSD Name: disk1
Medium Type: Rotational
Bay Name: Bay 2
Partition Map Type: MBR (Master Boot Record)
S.M.A.R.T. status: Verified
Volumes:
UNTITLED 1:
Capacity: 500.11 GB (500,107,860,992 bytes)
Available: 449.41 GB (449,412,988,928 bytes)
Writable: Yes
File System: MS-DOS FAT32
BSD Name: disk1s1
Mount Point: /Volumes/UNTITLED 1
Content: DOS_FAT_32
Intel ESB2 AHCI:
Vendor: Intel
Product: ESB2 AHCI
Link Speed: 3 Gigabit
Negotiated Link Speed: 3 Gigabit
Description: AHCI Version 1.10 Supported
HDS725050KLA360:
Capacity: 500.11 GB (500,107,862,016 bytes)
Model: HDS725050KLA360
Revision: K2AOAB5A
Serial Number:       KRVN67ZAK1RKSF
Native Command Queuing: Yes
Queue Depth: 32
Removable Media: No
Detachable Drive: No
BSD Name: disk0
Medium Type: Rotational
Bay Name: Bay 3
Partition Map Type: GPT (GUID Partition Table)
S.M.A.R.T. status: Verified
Volumes:
disk0s1:
Capacity: 209.7 MB (209,715,200 bytes)
BSD Name: disk0s1
Content: EFI
machd:
Capacity: 499.25 GB (499,248,103,424 bytes)
Available: 372.42 GB (372,419,407,872 bytes)
Writable: Yes
File System: Journaled HFS+
BSD Name: disk0s2
Mount Point: /
Content: Apple_HFS
Recovery HD:
Capacity: 650 MB (650,002,432 bytes)
BSD Name: disk0s3
Content: Apple_Boot
HDS725050KLA360:
Capacity: 500.11 GB (500,107,862,016 bytes)
Model: HDS725050KLA360
Revision: K2AOAB5A
Serial Number:       KRVN67ZAK1RKSF
Native Command Queuing: Yes
Queue Depth: 32
Removable Media: No
Detachable Drive: No
BSD Name: disk0
Medium Type: Rotational
Bay Name: Bay 3
Partition Map Type: GPT (GUID Partition Table)
S.M.A.R.T. status: Verified
Volumes:
disk0s1:
Capacity: 209.7 MB (209,715,200 bytes)
BSD Name: disk0s1
Content: EFI
machd:
Capacity: 499.25 GB (499,248,103,424 bytes)
Available: 372.42 GB (372,419,407,872 bytes)
Writable: Yes
File System: Journaled HFS+
BSD Name: disk0s2
Mount Point: /
Content: Apple_HFS
Recovery HD:
Capacity: 650 MB (650,002,432 bytes)
BSD Name: disk0s3
Content: Apple_Boot
Intel ESB2 AHCI:
Vendor: Intel
Product: ESB2 AHCI
Link Speed: 3 Gigabit
Description: AHCI Version 1.10 Supported
Intel ESB2 AHCI:
Vendor: Intel
Product: ESB2 AHCI
Link Speed: 3 Gigabit
Description: AHCI Version 1.10 Supported
Intel ESB2 AHCI:
Vendor: Intel
Product: ESB2 AHCI
Link Speed: 3 Gigabit
Description: AHCI Version 1.10 Supported

Try this:
clone your system and repair it with Disk Warrior instead
Or try a clean test system install on another drive
A must: SmcFanControl 2.2 - a mere 400 rpm extra to keep air cooling up
Try to run w/o externals. MyBook included.
Is that a 7200.11 1TB? they had a lot of issues.
Run AHT off your OEM DVD.
2008 had to have EFI and SMC updates to deal with freezes on wake from sleep, and like all models, high inrush current. Hopefully you have a UPS and is 1500VA unit.
When you do hard restart from power button, you almost certainly add more directory errors and to files requiring immediate attention to repair and rebuild the directory; and to scan and repair and delete cache and temp files and folders. A must. Invest in bootable backups SuperDuper along with Disk Warrior (or TechTool Pro 6, maybe Drive Genius 3 but I'd rate that #3).
TimeMachine has its own bad habits, especially with Green drives and some externals.
Try to rule out everything and then add back one at a time.
And it may just be time to replace the 8800, very common, a couple threads this week, and it is 3 yrs old. Might want ATI 5870 or 5770.

Mac Pro (early 2008) cannot startup

Similar Messages

Maybe you are looking for