Mac Pro never sleeps after upgrading to Mavericks

Hi Folks
Just realised that after upgrading to Mavericks from Mountain Lion, my Mac Pro never goes into sleep mode after the time set for it in System Preferences > Energy Saver.
This never happened with Mountain Lion.
Any body here having the same issue?
FYI - This is a 2012 Mac Pro having duo 6-cores, 64 GB RAM, 1 x SSD and 3 x HDD.
Thanks you for your comments.
B

Test after each of the following steps that you haven’t already tried:
Step 1
Take all the steps suggested in this support article. That's the starting point for any further effort to solve the problem. Skipping any of those steps may mean that the problem won't be solved. Note that, as stated in the article, the computerwill not sleep if Internet Sharing is enabled.
Step 2
From the menu bar, select
 ▹ System Preferences ▹ Accessibility ▹ Speakable Items: Off
Step 3
Select
 ▹ System Preferences ▹ Bluetooth ▹ Advanced...
and uncheck both boxes marked
Open Bluetooth Setup Assistant at startup if...
Step 4
Reset the SMC.
Step 5
Boot in safe mode and log in to the account with the problem. Note: If FileVault is enabled on some models, or if a firmware password is set, or if the boot volume is a software RAID, you can’t do this. Post for further instructions.
The login screen appears even if you usually log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
Safe mode is much slower to boot and run than normal. Don’t launch any applications at first. If sleep still doesn’t work properly, back up all data and reinstall the OS. After that, if you still have the issue, make a “Genius” appointment at an Apple Store to have the machine tested.
If sleep now works as expected, go on to the next step.
Step 6
Still in safe mode, launch the usual set of applications that are running when you have the problem, including your login items, one at a time, testing after each one. Some applications may not work; skip them. You might be able to identify the cause of the problem this way.
Step 7
If sleep is still working after you’ve launched all the usual applications, reboot as usual (not in safe mode) and test again. If sleep still works, you’re done, at least for the moment.
If you still have the sleep issue after booting out of safe mode, post again.

Similar Messages

Mac Pro runs slow after upgrading to mavericks?

I can't figure it out..
Been a mac user sinc Macintosh then mac plus.
First time i have no explanation.
I upgraded my 2010 Dual Quad Mac Pro 96gb ram, ran so very very fast with Sonnet 4 port eSATA and MOTU PCIE 424 card.
Ever since i upgraded it is so SLLLLOOOWWW!!. I have tired re-installing, contacted all the hardware vendors and software vendors, got all the updates.
I cant figure out why it is running like a 20 year old computer?. I get the wheel, Finder hangs allot, will not relaunch. I take out ALL THE THIRD PARTY CARDS, and boot, still runs like a turtle. Adobe creative suite slow, Aperature takes hrs to update library. Tried creating a new library. Still slow. Avid Media composer, Final Cut Pro X is so slow at rendering i can drive to Santa Cruz from Santa Barbara to MAvericks surf spot go surfing and come home to find out it is 95% done. Also copying large 20 gig folders from one internal to another takes hrs. used to take minuts.
I need help! It is so unpleasent using my mac pro now, , miserable user experience. I dread booting as it takes 5 min to go. I have dual monitors. Apple NVIDA card. could it be CUDA? no updates availble. I removed all the third party cards, and nothing happens. Removed all usb, FW, etc pluged in usb mouse from Apple Factory.
What ever happend there must be a patch or fix? all of my friends with Macs all having same slow issue. Please offer some fixes.
1. Is there a way to __Un-install Mavericks? and return my computer back to previous OS? without ruining or formating HD?
It seems like the only solution. I would Purchase a new MAc Pro, but none of my studio takes thunderbolt, and it is so exspensive i am cornerd. I would be so happy if i could just remove Mavericks, instead of taping aspirine all over my Macs. Please Apple send an update that fixes this. Just google it 100,00's of users? we all love Apple, we need you to help us help you! anyone? please help.
Please help!!
Kiind Regards
B

1. This procedure is a diagnostic test. It changes nothing, for better or worse, and therefore will not, in itself, solve your problem.
2. If you don't already have a current backup, back up all data before doing anything else. The backup is necessary on general principle, not because of anything in the test procedure. There are ways to back up a computer that isn't fully functional. Ask if you need guidance.
3. Below are instructions to run a UNIX shell script, a type of program. All it does is to gather information about the state of your computer. That information goes nowhere unless you choose to share it on this page. However, you should be cautious about running any kind of program (not just a shell script) at the request of a stranger on a public message board. If you have doubts, search this site for other discussions in which this procedure has been followed without any report of ill effects. If you can't satisfy yourself that the instructions are safe, don't follow them.
Here's a summary of what you need to do: Copy a line of text from this web page into the window of another application. Wait for the script to run. It usually takes a couple of minutes. Then paste the results, which will have been copied automatically, back into a reply on this page. The sequence is: copy, paste, wait, paste again. Details follow.
4. You may have started the computer in "safe" mode. Preferably, these steps should be taken in “normal” mode. If the system is now in safe mode and works well enough in normal mode to run the test, restart as usual. If you can only test in safe mode, do that.
5. If you have more than one user, and the one affected by the problem is not an administrator, then please run the test twice: once while logged in as the affected user, and once as an administrator. The results may be different. The user that is created automatically on a new computer when you start it for the first time is an administrator. If you can't log in as an administrator, test as the affected user. Most personal Macs have only one user, and in that case this section doesn’t apply.
6. The script is a single long line, all of which must be selected. You can accomplish this easily by triple-clicking anywhere in the line. The whole line will highlight, though you may not see all of it in your browser, and you can then copy it. If you try to select the line by dragging across the part you can see, you won't get all of it.
Triple-click anywhere in the line of text below on this page to select it:
PATH=/usr/bin:/bin:/usr/sbin:/sbin; clear; Fb='%s\n\t(%s)\n'; Fm='\n%s:\n\n%s\n'; Fr='\nRAM details:\n%s\n'; Fs='\n%s: %s\n'; Fu='user %s%%, system %s%%'; PB="/usr/libexec/PlistBuddy -c Print"; A () { [[ a -eq 0 ]]; }; M () { find -L "$d" -type f | while read f; do file -b "$f" | egrep -q XML\|exec && echo $f; done; }; Pc () { o=`grep -v '^ *#' "$2"`; Pm "$1"; }; Pm () { [[ "$o" ]] && o=`sed '/^ *$/d; s/^ */ /' <<< "$o"` && printf "$Fm" "$1" "$o"; }; Pp () { o=`$PB "$2" | awk -F'= ' \/$3'/{print $2}'`; Pm "$1"; }; Ps () { o=`echo $o`; [[ ! "$o" =~ ^0?$ ]] && printf "$Fs" "$1" "$o"; }; R () { o=; [[ r -eq 0 ]]; }; SP () { system_profiler SP${1}DataType; }; id | grep -qw '80(admin)'; a=$?; A && sudo true; r=$?; t=`date +%s`; clear; { A || echo $'No admin access\n'; A && ! R && echo $'No root access\n'; SP Software | sed '8!d;s/^ *//'; o=`SP Hardware | awk '/Mem/{print $2}'`; o=$((o<4?o:0)); Ps "Total RAM (GB)"; o=`SP Memory | sed '1,5d; /[my].*:/d'`; [[ "$o" =~ s:\ [^O]|x([^08]||0[^2]8[^0]) ]] && printf "$Fr" "$o"; o=`SP Diagnostics | sed '5,6!d'`; [[ "$o" =~ Pass ]] || Pm "POST"; o=`SP USB | sed -n '1d; /:$/{s/ *:$//;x;s/\n//p;}; /V.*[(]/{s/^[^(]*/ /;H;}; /Apple/{s/.//g;h;}'`; Pm "USB"; o=`pmset -g therm | sed 's/^.*C/C/'`; [[ "$o" =~ No\ th|pms ]] && o=; Pm "Thermal conditions"; o=`pmset -g sysload | grep -v :`; [[ "$o" =~ =\ [^GO] ]] || o=; Pm "System load advisory"; o=`nvram boot-args | awk '{$1=""; print}'`; Ps "boot-args"; d=(/ ""); D=(System User); for i in 0 1; do o=`cd ${d[$i]}L*/L*/Dia* && ls | awk -F_ '!/ag$/{$NF=a[split($NF,a,".")]; print}' | tail`; Pm "${D[$i]} diagnostics"; done; o=`syslog -F bsd -k Sender kernel -k Message CReq 'GPU |hfs: Ru|I/O e|n Cause: -|NVDA\(|pagin|SATA W|ssert|timed? ?o' | tail -n25 | awk '/:/{$4=""; $5=""};1'`; Pm "Kernel messages"; o=`df -m / | awk 'NR==2 {print $4}'`; o=$((o<5120?o:0)); Ps "Free space (MiB)"; o=$(($(vm_stat | awk '/eo/{sub("\\.",""); print $2}')/256)); o=$((o>=1024?o:0)); Ps "Pageouts (MiB)"; s=( `sar -u 1 10 | sed '$!d'` ); [[ s[4] -lt 85 ]] && o=`printf "$Fu" ${s[1]} ${s[3]}` || o=; Ps "Total CPU usage" && { s=(`ps acrx -o comm,ruid,%cpu | sed '2!d'`); o=${s[2]}%; Ps "CPU usage by process \"$s\" with UID ${s[1]}"; }; s=(`top -R -l1 -n1 -o prt -stats command,uid,prt | sed '$!d'`); s[2]=${s[2]%[+-]}; o=$((s[2]>=25000?s[2]:0)); Ps "Mach ports used by process \"$s\" with UID ${s[1]}"; o=`kextstat -kl | grep -v com\\.apple | cut -c53- | cut -d\< -f1`; Pm "Loaded extrinsic kernel extensions"; R && o=`sudo launchctl list | sed 1d | awk '!/0x|com\.(apple|openssh|vix\.cron)|org\.(amav|apac|calendarse|cups|dove|isc|ntp|post[fg]|x)/{print $3}'`; Pm "Extrinsic system jobs"; o=`launchctl list | sed 1d | awk '!/0x|com\.apple|org\.(x|openbsd)|\.[0-9]+$/{print $3}'`; Pm "Extrinsic agents"; o=`for d in {/,}L*/Lau*; do M; done | grep -v com\.apple\.CSConfig | while read f; do ID=$($PB\ :Label "$f") || ID="No job label"; printf "$Fb" "$f" "$ID"; done`; Pm "launchd items"; o=`for d in /{S*/,}L*/Star*; do M; done`; Pm "Startup items"; o=`find -L /S*/L*/E* {/,}L*/{A*d,Compon,Ex,In,Keyb,Mail/B,P*P,Qu*T,Scripti,Servi,Spo}* -type d -name Contents -prune | while read d; do ID=$($PB\ :CFBundleIdentifier "$d/Info.plist") || ID="No bundle ID"; [[ "$ID" =~ ^com\.apple\.[^x]|Accusys|ArcMSR|ATTO|HDPro|HighPoint|driver\.stex|hp-fax|\.hpio|JMicron|microsoft\.MDI|print|SoftRAID ]] || printf "$Fb" "${d%/Contents}" "$ID"; done`; Pm "Extrinsic loadable bundles"; o=`find -L /u*/{,*/}lib -type f | while read f; do file -b "$f" | grep -qw shared && ! codesign -v "$f" && echo $f; done`; Pm "Unsigned shared libraries"; o=`launchctl getenv DYLD_INSERT_LIBRARIES`; Pm "Inserted libraries"; o=`find -L {,/u*/lo*}/e*/periodic -type f -mtime -10d`; Pm "Modified periodic scripts"; o=`scutil --proxy | grep Prox`; Pm "Proxies"; o=`scutil --dns | awk '/r\[0\] /{if ($NF !~ /^1(0|72\.(1[6-9]|2[0-9]|3[0-1])|92\.168)\./) print $NF; exit}'`; Ps "DNS"; R && o=`sudo profiles -P | grep : | wc -l`; Ps "Profiles"; f=auto_master; [[ `md5 -q /etc/$f` =~ ^b166 ]] || Pc $f /etc/$f; for f in fstab sysctl.conf crontab launchd.conf; do Pc $f /etc/$f; done; Pc "hosts" <(grep -v 'host *$' /etc/hosts); Pc "User launchd" ~/.launchd*; R && Pc "Root crontab" <(sudo crontab -l); Pc "User crontab" <(crontab -l); R && o=`sudo defaults read com.apple.loginwindow LoginHook`; Pm "Login hook"; Pp "Global login items" /L*/P*/loginw* Path; Pp "User login items" L*/P*/*loginit* Name; Pp "Safari extensions" L*/Saf*/*/E*.plist Bundle | sed 's/\..*$//;s/-[1-9]$//'; o=`find ~ $TMPDIR.. $ -flags +sappnd,schg,uappnd,uchg -o ! -user $UID -o ! -perm -600 $ | wc -l`; Ps "Restricted user files"; cd; o=`SP Fonts | egrep "Valid: N|Duplicate: Y" | wc -l`; Ps "Font problems"; o=`find L*/{Con,Pref}* -type f ! -size 0 -name *.plist | while read f; do plutil -s "$f" >&- || echo $f; done`; Pm "Bad plists"; d=(Desktop L*/Keyc*); n=(20 7); for i in 0 1; do o=`find "${d[$i]}" -type f -maxdepth 1 | wc -l`; o=$((o<=n[$i]?0:o)); Ps "${d[$i]##*/} file count"; done; o=$((`date +%s`-t)); Ps "Elapsed time (s)"; } 2>/dev/null | pbcopy; exit 2>&-
Copy the selected text to the Clipboard by pressing the key combination command-C.
7. Launch the built-in Terminal application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Terminal in the icon grid.
When you launch Terminal, a text window will open with a line already in it, ending either in a dollar sign ($) or a percent sign (%). If you get the percent sign, enter
exec sh
in the window and press return. You should then get a new line ending in a dollar sign.
Click anywhere in the Terminal window and paste (command-V). The text you pasted should vanish immediately. If it doesn't, press the return key.
If you're logged in as an administrator, you'll be prompted for your login password. Nothing will be displayed when you type it. You will not see the usual dots in place of typed characters. Make sure caps lock is off. Type carefully and then press return. You may get a one-time warning to be careful. If you make three failed attempts to enter the password, the test will run anyway, but it will produce less information. In most cases, the difference is not important. If you don't know your password, or if you prefer not to enter it, just press return three times at the password prompt.
If you're not logged in as an administrator, you won't be prompted for a password. The test will still run. It just won't do anything that takes administrator privileges.
The test may take up to a few minutes to run, depending on how many files you have and the speed of the computer. A computer that's abnormally slow may take longer to run the test. While it's running, there will be nothing in the Terminal window and no indication of progress. Wait for the line "[Process completed]" to appear. If you don't see it within half an hour or so, the test probably won't complete in a reasonable time. In that case, close the Terminal window and report your results. No harm will be done.
8. When the test is complete, quit Terminal. The results will have been copied to the Clipboard automatically. They are not shown in the Terminal window. Please don't copy anything from there. All you have to do is start a reply to this comment and then paste by pressing command-V again.
If any private information, such as your name or email address, appears in the results, anonymize it before posting. Usually that won't be necessary.
When you post the results, you might see the message, "You have included content in your post that is not permitted." It means that the forum software has misidentified something in the post as a violation of the rules. If it happens, please post the test results on Pastebin, then post a link here to the page you created.
Note: This is a public forum, and others may give you advice based on the results of the test. They speak only for themselves, and I don't necessarily agree with them.
Copyright © 2014 Linc Davis. As the sole author of this work, I reserve all rights to it except as provided in the Terms of Use of Apple Support Communities ("ASC"). Readers of ASC may copy it for their own personal use. Neither the whole nor any part may be redistributed.

Mac pro cannot boot after upgrade to 10.8.3

My Mac Pro cannot boot after upgrade to 10.8.3. Anything firmware I can reset or how should I do.
I am using a early 2008 Mac Pro

Can you boot into safe mode? http://support.apple.com/kb/ht1455
If not, how about Recovery? http://support.apple.com/kb/ht4718
If you can, run Disk Utlity and repair the disk. You can try rebooting normally, but I would just reinstall after quitting Disk Utility.

Thunderbolt Display has issue with weird washed-out colors after waking from sleep (after upgrade to Mavericks)

I've got a Thunderbolt Display that I use with my Macbook Air (mid 2012) - usually in clamshell mode.
When I let the computer go to sleep, and then wake it up by clicking the mouse, the monitor turns back on but the colors are washed out and purple looking.
The display goes back to normal when I unplug and replug it to my laptop.
I first noticed this problem after upgrading to Mavericks.
I made a video demonstrating the issue here:
http://www.youtube.com/watch?v=19179-MVpWA&feature=youtu.be
Any ideas?
Thanks!
Will

Same thing for me too. Late 2012 13" MBP Retina. I have to unplug the Thunderbolt cable and plug it back in.
This has only started for me in the last two days. The first two weeks of Mavericks was ok.
Update: I just got back from a trip. I was using the laptop separate from the Thunderbolt display. I hadn't restarted since I returned and connected the monitor. I've just rebooted, and put the computer to sleep. After resuming from sleep, the display is ok. Maybe try rebooting? I'll update if it continues.

2009 Mac Pro not letting me upgrade to Mavericks nor 10.8

I have a 2009 Mac Pro with OS 10.7.5 installed, it running perfectly fine but for some reason it's not letting me update to 10.8 nor 10.9. Mavericks works totally fine from ssd card mounted on a usb dock but when I try to use the SSD inside or the hard drive the Mac Pro came with it does not boot up. I was getting a problem when trying to upgrade Mavericks from the store where Mac Pro wouldn't boot, it will just show a question mark so I reinstalled OS 10.7.5. When trying to install Mavericks from a usb drive, Mac Pro does not see none of the internal hard drives and for some reason does not even let me eject the optical bay, has this happen to anyone if yes, what you do to fix the problem.

"Image" was not a reference to the physical drive, but rather the actual bytes representing the version of Mac OS X on the drive.
• If you built Mac OS X on that drive from the Mac OS X that shipped with another Mac, it will be trouble.
• If you built the Mac OS X on that drive from a "Full Retail", "Purchased" (for $0, but it still counts as a purchase) version from the Mac App store, it has all Drivers and should work fine.

MacBook Pro Early 2008 won't go to sleep after upgrade to Mavericks

I have a MacBook Pro that is of the Early 2008 variety. Ever since I upgraded to OS X Mavericks two nights ago, it will no longer go to sleep. This is with me using either the power button or directly selecting sleep from the Apple menu. All that happens is it blanks the screen. If I hit a key it turns the screen on and asks for password. With screen off I can definitely hear the fans and harddrive still in operation. I have to shut down to make it turn off. How to fix this??

As soon as you wake up your display, launch Terminal from your Applications > Utilites folder and enter the following command.
pmset -g
in the resulting text, is there a reason next to sleep that says what activity is preventing it from sleeping?
eg:
sleep 20 (sleep prevented by mds, UserEventAgent)
Then in System Prefernces > Energy Saver, does clicking on Restore Defaults resolve the issue?
(This will reset any preset settings, but it may also clear the issue for you)

Mac is running slow after upgrading to maverick

My macbook pro is running very slow since I upgraded to 10.9

Here's my suggestion:
Fixing a Mavericks Installation Problem
How to manage a failed OS X Mavericks installation | MacFixIt - CNET Reviews.
1. Intel-based Macs: Resetting the System Management Controller (SMC).
2. Repair the Hard Drive and Permissions - Lion/Mountain Lion/Mavericks
Boot to the Recovery HD:
Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
Repair
When the recovery menu appears select Disk Utility. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported then click on the Repair Permissions button. When the process is completed, then quit DU and return to the main menu. Select Restart from the Apple menu.
3. Re-download and reinstall Mavericks.
Boot to the Recovery HD: Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
Repair the Hard Drive and Permissions: Upon startup select Disk Utility from the main menu. Repair the Hard Drive and Permissions as follows.
When the recovery menu appears select Disk Utility. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the main menu.
Reinstall Lion/Mountain Lion/Mavericks: Select Reinstall Lion/Mountain Lion/Mavericks and click on the Continue button.
Note: You will need an active Internet connection. I suggest using Ethernet if possible because it is three times faster than wireless.

Mac Pro keyboard issues after OS X Mavericks v 10.9.5 Update

My keyboard stopped functioning after the last OS X Mavericks v10.9.5 Update on 9/18/14. I'm unable to input my login information to start a remote access session. I need to fix this so I can resume working from home. Is their an easy fix to this problem?

Both, but you need to make sure your hardware is compatible.
http://gizmodo.com/heres-the-list-of-macs-compatible-with-os-x-mavericks-5125503 69

Macbook Pro Constantly Restarting after Upgrading to Mavericks

Upgraded this afternoon and Macbook will not stay up for more that 3 minutes before restarting and giving the message that it is restarting because of a problem.

Known GPU problems with MacBook Pro 15" Mid 2010 systems
https://discussions.apple.com/docs/DOC-5681

Wifi problem with Mac after upgrade to Mavericks

I just upgraded to Mavericks but something wrong with my wifi.
i can get internet through LAN link from Airport but not through wifi even i can receive an IP address
i tried connect to hotspot with my iphone5s and it works.
Other devices can use wifi just fine through Airport, just not my Mac using Mavericks
In conclusion,
Airport should be fine because my other devices works.
Mac wifi should be fine too because i can connect using hotspot.
so why it's not working when i connect Mac to Airport?

I was having problems connecting to Wifi with my Macbook Pro (!2010), after upgrading to Mavericks. I was on the phone repeateadly with AT&T because I have Uverse. Testing everything (channels, signal strength) and had techs come out to check the line, ports, switches, etc. When I hardwired the Mac into the Uverse router, it worked fine. This rulled out any problems with the line in.
I considered getting a repeater but then I read that repeaters are not really good and it is better to reconfigure a router to act as an access point on the network. Plunked down about $80 for a Belkin AC750 router at Best Buy. In the setup it has an option to set it up as an access point only. Clicked that, connected it to my Motorola NVG510 Uverse modem and then connected to the Belkin router from my Mac. Voila! It's been a solid 11+ Mbs ever since (my plan maxes at 12Mbs). Connection is still solid and life if good even though it ***** to plunk down another $80 for a second router. But it was worth it just to get rid of the headaches.
I think the wifi capabilities of the Motorola NVG510 modem are the cause of a lot of problems with AT&T Uverse issues, particularly for Mac owners. I think it was also causing my Airport Expresses to drop occasionally.... Few minutes of music then drop... music drop.... All gone now.
I don't know if you are on Uverse but if so, I highly recommend configuring a second router as an acces point (it can be any old router you still might have - the setup is just a bit trickier because you have to do it manually).
Good luck.

After upgrading to Mavericks on my Mac Pro, mail always requires that I type in my password when launching. How do I change that?

After upgrading to Mavericks on my Mac Pro, mail always requires that I type in my password when launching. How do I change that?

If your password is accepted, and Mail connects to the account, but you're prompted for the password repeatedly, take each of the following steps that you haven't already tried. Note: these steps don't apply if the server rejects the password. That's a different problem.
Step 1
When prompted for the password, check the box marked Remember this password in my keychain.
Step 2
Check that the keychain is working.
Step 3
Check that the default keychain is unlocked.

After upgrading to Mavericks my Mac Pro does not open my double CD drives when I hit eject in the menu bar it locks up (please Help)?

After upgrading to Mavericks my Mac Pro does not open my double CD drives when I hit eject in the menu bar it locks up (please Help)?

If you have more than one user account, these instructions must be carried out as an administrator.
Launch the Console application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Console in the icon grid.
Step 1
Make sure the title of the Console window is All Messages. If it isn't, select All Messages from the SYSTEM LOG QUERIES menu on the left. If you don't see that menu, select
View ▹ Show Log List
from the menu bar.
Enter "BOOT_TIME" (without the quotes) in the search box. Note the timestamps of those log messages, which refer to the times when the system was booted. Now clear the search box and scroll back in the log to the last boot time after you had the problem. Select the messages logged before the boot, while the system was unresponsive or was failing to shut down. Copy them to the Clipboard by pressing the key combination command-C. Paste into a reply to this message (command-V). Please include the BOOT_TIME message at the end of the log extract.
If there are runs of repeated messages, post only one example of each. Don’t post many repetitions of the same message.
When posting a log extract, be selective. In most cases, a few dozen lines are more than enough.
Please do not indiscriminately dump thousands of lines from the log into this discussion.
Important: Some private information, such as your name, may appear in the log. Anonymize before posting.
Step 2
Still in Console, look under System Diagnostic Reports for crash or panic logs, and post the entire contents of the most recent one, if any. In the interest of privacy, I suggest you edit out the “Anonymous UUID,” a long string of letters, numbers, and dashes in the header of the report, if present (it may not be.) Please don’t post any other kind of report — it will be very long and not helpful.

Mac book pro will not sleep after i installed mavericks

mac book pro will not sleep after i installed mavericks the sleep indicator light stays solid and fans still run but the display turns off

mac book pro will not sleep after i installed mavericks the sleep indicator light stays solid and fans still run but the display turns off

I'm using matchbook pro and I'm unable to find iPhoto after upgrading to Maverick os

I'm using matchbook pro and I'm unable to find iPhoto after upgrading to Maverick os

Open the Mac App Store application and see if iPhoto is under your "Purchases" tab.
Clinton

My macbook pro is running really slow after upgrade to Mavericks

my macbook pro is running really slow after upgrading to Mavericks....any ideas?

OS X Mavericks: If your Mac runs slowly
The above link is not very useful, so if it doesn't help read on.
There are many potential reasons that a Mac may be running slower than expected, but more information is required to begin troubleshooting, much more.
Back up your documents and everything else important to you before proceeding. It is premature to conclude your hard disk is failing, but the symptoms you describe may presage an impending disk failure, and you should have backups anyway.
To help determine the possible causes of this behaviour read the following. None of what follows is intended to fix anything, but it will provide the additional information required to advance troubleshooting:
Boot OS X Recovery by holding ⌘ and r (two fingers) while you start your Mac. At the Mac OS X Utilities screen, select Disk Utility. Select your startup volume (usually named "Macintosh HD") and click the Repair Disk button. Describe any errors it reports in red.
When it finishes restart your Mac and test again for operation. If it's still not behaving as you expect it should, please post the results of EtreCheck in accordance with the following instructions:
Apple Support Communities contributor etresoft wrote a very useful app to quickly gather certain system information that may help point to a cause of this problem. Go to his website, download and run EtreCheck:
http://www.etresoft.com/etrecheck
Etrecheck will be in your Downloads folder. Open it from there. You may see the following dialog box:
Click Open - etresoft contributes to this forum frequently and can be considered a trustworthy developer.
It will take a moment to run as it collects its data.
Copy and paste its output in a reply.
Do not be concerned about anything that says "Problem" or “failed” or anything else that may appear in red.
EtreCheck was designed to remove any personal information (such as your computer's name and serial numbers) but if you see anything that looks like an email address or any other personal information that should not be divulged to others, please delete or obscure that information when you post the reply.
When you are finished with EtreCheck, quit the program. It occupies very little space, and you can keep it or drag it to the Trash as you wish.
After completing the above please determine if the problems also occur in "Safe Mode":
Safe Mode or "Safe Boot" is a troubleshooting mode that bypasses all third party system extensions and loads only required system components. Read about it: Starting up in Safe Mode
You must disable FileVault before you can start your Mac in Safe Mode.
Starting your Mac in Safe Mode will take longer than usual, graphics will not render smoothly, audio is disabled on some Macs, and some programs (iTunes for example) may not work at all.
Merely starting your Mac in Safe Mode is not intended to resolve the problem, it's to observe its performance without certain additional components.
To end Safe Mode restart your Mac normally. Shutdown will take longer as well.
System performance problems for reasons that cannot be isolated to any other cause justify an SMC reset. Be sure to read the procedure carefully and follow all the steps exactly as written, even if they seem inapplicable or trivial.

Mac Pro never sleeps after upgrading to Mavericks

Similar Messages

Maybe you are looking for