Mac Pro started running very slow
Just recently, my computer started taking a long time to load prgrams, and to quit programs (1 - 2 minutes). Plus programs have been crashing or not responding when I try to quit. I don't know what's going on.
I ran the disc utlility and the hard drive checked out fine. The drive is less than half full. Any ideas? Anyone?
EP
First, back up all data immediately, as your boot drive may be failing.
If iCloud is enabled, disable it.
Disconnect all wired peripherals except keyboard, mouse, and monitor, if applicable. Launch the usual set of applications you use when you notice the problem.
Step 1
Launch the Activity Monitor application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ If you’re running OS X 10.7 or later, open LaunchPad. Click Utilities, then Activity Monitor in the page that opens.
Select the CPU tab of the Activity Monitor window.
Select All Processes from the menu in the toolbar, if not already selected.
Click the heading of the % CPU column in the process table to sort the entries by CPU usage. You may have to click it twice to get the highest value at the top. What is it, and what is the process? Also post the values for % User, % System, and % Idle at the bottom of the window.
Select the System Memory tab. What values are shown in the bottom part of the window for Page outs and Swap used?
Step 2
You must be logged in as an administrator to carry out this step.
Launch the Console application in the same way as above. Make sure the title of the Console window is All Messages. If it isn't, select All Messages from the SYSTEM LOG QUERIES menu on the left.
Post the 50 or so most recent messages in the log — the text, please, not a screenshot.
Important: Some personal information, such as your name, may appear in the log. Edit it out before posting.
Similar Messages
-
HT1338 my mac pro started running very slow not all the time it is only 2 months old
My new macpro has been running very slow off and on (mostly on) it is only 2 months old I took it into the genius bar and they could not find anything wrong. I took it home and it ran fine for a short while then started up again. I have watched activity monitor and can see no direct corellation. Anyone have any ideas?
Did you install anything new lately?
Run any programs that purport to "clean", "speed up", or "optimize" your Mac -
My mac pro is running very slow and I have a pin wheel turning
My mac pro is running very slow and I have a pin wheel turning what can I do?
https://support.apple.com/kb/DL1433
https://www.apple.com/macosx/recovery/
http://support.apple.com/kb/HT4718 -
My MacBook Pro started running very slow. I did disk utility/repair
My MacBook Pro started running very slow. I did disk utility/repair and it helped but still very slow. Repair gave me this message, "SUID file 'System/Library/CoreServices/RemoteManagement/ARDAgent.app/Contents/MacOS/ARDAg ent has been modified and will not be repaired." Any suggestions on this message and/or what else I can do to get my computer back to the way it used to run? Thank you!
It says 199.15 GB free of 499.25 GB. Can I remove the Remote Management program to solve the other unrepairable problem?
-
My Mac pro is running very slow. Memory used 3.99 out of 4.00
Hello,
My mac is running very slow
- I have noticed that memory used is 3.99 out of 4.00 and the process taking most of it is safari web content. Problem also appears when I use Firefox
- this happens even I only have safari or firefox open. No other applications
- I have about 80Gb free disk space
Thanks for any suggestions1. This procedure is a diagnostic test. It changes nothing, for better or worse, and therefore will not, in itself, solve the problem. But with the aid of the test results, the solution may take a few minutes, instead of hours or days.
2. If you don't already have a current backup, back up all data before doing anything else. The backup is necessary on general principle, not because of anything in the test procedure. Backup is always a must, and when you're having any kind of trouble with the computer, you may be at higher than usual risk of losing data, whether you follow these instructions or not.
There are ways to back up a computer that isn't fully functional. Ask if you need guidance.
3. Below are instructions to run a UNIX shell script, a type of program. All it does is to collect information about the state of the computer. That information goes nowhere unless you choose to share it. However, you should be cautious about running any kind of program (not just a shell script) on the advice of a stranger. If you have doubts, search this site for other discussions in which this procedure has been followed without any report of ill effects. If you can't satisfy yourself that the instructions are safe, don't follow them. Ask for other options.
Here's a summary of what you need to do, if you choose to proceed:
☞ Copy a line of text in this window to the Clipboard.
☞ Paste into the window of another application.
☞ Wait for the test to run. It usually takes a few minutes.
☞ Paste the results, which will have been copied automatically, back into a reply on this page.
The sequence is: copy, paste, wait, paste again. You don't need to copy a second time. Details follow.
4. You may have started the computer in "safe" mode. Preferably, these steps should be taken in “normal” mode, under the conditions in which the problem is reproduced. If the system is now in safe mode and works well enough in normal mode to run the test, restart as usual. If you can only test in safe mode, do that.
5. If you have more than one user, and the one affected by the problem is not an administrator, then please run the test twice: once while logged in as the affected user, and once as an administrator. The results may be different. The user that is created automatically on a new computer when you start it for the first time is an administrator. If you can't log in as an administrator, test as the affected user. Most personal Macs have only one user, and in that case this section doesn’t apply. Don't log in as root.
6. The script is a single long line, all of which must be selected. You can accomplish this easily by triple-clicking anywhere in the line. The whole line will highlight, though you may not see all of it in the browser window, and you can then copy it. If you try to select the line by dragging across the part you can see, you won't get all of it.
Triple-click anywhere in the line of text below on this page to select it:
PATH=/usr/bin:/bin:/usr/sbin:/sbin:/usr/libexec;clear;cd;p=(Software Hardware Memory Diagnostics Power FireWire Thunderbolt USB Fonts 51 4 300 25 5120 ' KiB/s' 1024 85 % 5 1 ' MB/s' 25000 ' ports' 'com.autodesk.AutoCad com.evenflow.dropbox com.google.GoogleDrive' 'DYLD_INSERT_LIBRARIES DYLD_LIBRARY_PATH' -86 \< '>=' 'N\/A' down up 100 25 recvfrom sendto 'v[0]=' 'a=(' ';[[ "${v[0]}" ]]' ');v[0]=$a;ind=0' '(){ x=;[[ "$4" ]]&&x=\"${v[$4]}\";' '`eval "${c1[$1]} ${c2[$2]}" "$x"|' ' "${s[$3]}"`' ';};' CFBundleIdentifier 25 );f=('\n%s: %s\n' '\n%s\n\n%s\n' '\nRAM details\n%s\n' '\n%s: user %s%%, system %s%%\n' '%s\n\t(%s)\n' '%s %s' );s=('/^ *$|CSConfigDot/d;s/^ */ /;s/[-0-9A-Fa-f]{22,}/UUID/g;s/(ochat)\.[^.]+(\..+)/\1\2/;/Shared/!s/\/Users\/[^/]+/~/g' 's/^ *//;5p;6p;8p;12p' '/ Id/s/.+: //p;/Mem/{s/[^0-9]//g;p;}' '1,5d;/[Bmy].*:/d;H;${g;/s: [^EO]|x([^08]|02[^F]|8[^0])/p;}' '5h;6{H;g;/P/!p;}' '/Cy|Cond.*: [^N]/s/^.*://p' '/:$/{s/ *:$//;x;s/\n//;/Apple|Genesy|Intel|SMSC/d;s/\n.*//;/\)/p;};/^ *(V.+ [0N]|Man).+ /{s/ 0x.... //;s/[()]//g;s/(.+: )(.+)/ (\2)/;H;}' 's/^.*C/C/;H;${g;/No th|pms/!p;}' '/= [^GO]/p' '{$1=""};1' '/Of/!{s/^.+is |\.//g;p;}' '/(sh|ng|ic)$/p' '/:/{$4=""};1' 'NR==2{print $4}' '/po/{sub("\\.","");print int($2/256)}' '$p' 2p '$8~/[RW]/{print $4,$1,int($9/10000000)}' 's:^:/:p' '/\.kext\/(Contents\/)?Info\.plist$/p' 's/^.{52}//;s/ .+//p' '/Launch[AD].+\.plist$/p' '/\.xpc\/(Contents\/)?Info\.plist$/p' 'NR>1&&!/0x|\.[0-9]+$|com\.apple\.launchctl\.(Aqua|Background|System)$/{print $3}' '/\.(framew|lproj)/d;/plist:|:.+(M.+exec|scrip)/s/:[^:]+//p' '/root/p' '/\/Contents\/.+\/Contents|Applic|Autom|Frameworks/d;/Lib.+\/Info.plist$/p' '/^\/usr\/lib\/.+dylib$/p' '/\/etc\/(auto_m|hosts[^.]|peri)/s/^\.\/[^/]+//p' '/\/(Contents\/.+\/Contents|Frameworks)\//d;p' 's/\/(Contents\/)?Info.plist$//;p' '{gsub("^| ","||kMDItem'${p[43]}'=");sub("^.."," ")};1' p '{print $3"\t"$1}' 's/\'$'\t''.+//p' 's/1/On/p' '/Prox.+: [^0]/p' '/e:/{print $2}' '1d;/[^)]$/{s/^\(.+\) //;h;d;};/[^ ]\)$/{s/^.+: |.$//g;G;s/\n/:/p;}' '/r\[0\] /&&$NF!~/^1(0|72\.(1[6-9]|2[0-9]|3[0-1])|92\.168)\./{print $NF;exit}' '!/^T/{printf "(static)";exit}' 's/^.+://p' '(/k:/&&$3!~/(255\.){3}0/)||(/v6:/&&$2!~/A/)' '/lR/{print $2}' 'NR==2{print int($7/1024),int($10/1024)}' 'END{$3=int($3/10240);print}' 'END{if($5~/pro/)print$3}' 'BEGIN{L='${p[44]}'}!/^[[:space:]]*(#.*)?$/{l++;if(l<=L)f=f"\n\t"$0}END{print "\nContents of "FILENAME"\n"f;if(l>L)print"\n\tand "l-L" more line(s)"}' 'BEGIN{FS="= "}/Path/{print $2}' '/^ +B/{s/.+= |(-[0-9]+)?\.s.+//g;p;}' 'END{print NR}' '/id: N|te: Y/{i++}END{print i}' '/^F/!p' '/:/{$0="'"${p[28]}"'"};1' 'BEGIN{FS=":"}{n=split($3,a,".");sub(/_2.+/,"",a[n-1]);print($2,a[n-1],a[n],$1)|"sort";b=b$1}END{if(b)print("\n\t* Code injection")}' '/apsd|OpenD/!s/:.+//p' '$2>'${p[9]}'{$2=$2-1;print}' );c1=(system_profiler 'pmset -g' nvram fdesetup find syslog df vm_stat sar ps iostat 'sudo iotop' top pkgutil PlistBuddy whoami cksum kextstat launchctl 'sudo launchctl' crontab 'sudo defaults read' stat lsbom mdfind 'for i in ${p[24]};do ${c1[18]} ${c2[27]} $i;done' 'defaults read' scutil route networksetup 'sed -En' awk '/S*/*/P*/*/*/*/*/airport -I' netstat 'sudo dtrace' 'sudo profiles' 'sudo crontab' );c2=('com.apple.loginwindow LoginHook' '-c Print /L*/P*/loginw*' '-c Print L*/P*/*loginit*' '-c Print L*/Saf*/*/E*.plist' '~ $TMPDIR.. \( -flags +sappnd,schg,uappnd,uchg -o ! -user $UID -o ! -perm -600 \)' '.??* -path .Trash -prune -o -type d -name *.app -print -prune' '-c Print\ :'${p[43]}' 2>&1' '-c Print\ :Label 2>&1' '{/,}L*/{Con,Pref}* -type f ! -size 0 -name *.plist -exec plutil -s {} \;' "-f'%N: %l' Desktop L*/Keyc*" therm sysload boot-args status '-F bsd -k Sender kernel -k Message CReq "caug|dead[^l]|GPU |hfs: Ru|last value [1-9]|n Cause: -|NVDA\(|pagin|proc: t|Roamed|rror|ssert|Thrott|timed? ?o|WARN" -k Message Ane "SMC:" -o -k Sender fseventsd -k Message CReq "SL"' '-u 1 10' 'acrx -o comm,ruid,%cpu' '-C 10 1' '-f -pfc /var/db/*/*.{BS,Bas,Es,OSXU,Rem}*.bom' '{/,}L*/Lo*/Diag* -type f \( -exec grep -lq "^Thread c" {} \; -exec printf \* \; -o -true \) -execdir stat -f:%Sc:%N -t%F {} \;' '-L {/{S*/,},}L*/Lau* -type f' '-L /{S*/,}L*/StartupItems -type f -exec file {} +' '-L /S*/L*/{C*/Sec*A,E}* {/,}L*/{A*d,Compon,Ex,In,iTu,Keyb,Mail/B,P*P,Qu*T,Scripti,Sec,Servi,Spo}* -type f -name Info.plist' '/usr/lib -type f -name *.dylib' `awk "${s[31]}"<<<${p[23]}` " /e*/{auto_master,{cron,fs}tab,hosts,{launchd,sysctl}.conf} /u*/lo*/e*/per*/*/* .launchd.conf" list getenv '/Library/Preferences/com.apple.alf globalstate' --proxy '-n get default' -listnetworkserviceorder --dns -getdnsservers -getinfo '-b -I' '-m /' '' -n1 '-R -l1 -n1 -o prt -stats command,uid,prt' '--regexp --only-files --files com.apple.pkg.*|sort|uniq' -kl -l -P );N1=${#c2[@]};for j in {0..8};do c2[N1+j]=" SP${p[j]}DataType";done;N2=${#c2[@]};for j in 0 1;do c2[N2+j]="-n 'syscall::'${p[33+j]}':return {@[execname,uid]=sum(arg0)} tick-10sec {exit(0)}'";done;l=(Model 'RAM (GB)' 'RAM details' POST 'Battery cycles' 'Battery condition' 'Bad plists' 'High file counts' User Heat 'System load' 'boot args' FileVault 'Diagnostic reports' Log 'Free space (MiB)' 'Swap (MiB)' 'CPU total' 'CPU per process' 'Average I/O (MB/s)' 'I/O per process' 'Mach ports' kexts Daemons Agents launchd 'Startup items' 'Admin access' 'Root access' Bundles dylibs Apps 'Font issues' 'Inserted dylibs' Firewall Proxies DNS TCP/IP RSSI Profiles 'Elapsed time (s)' 'Root crontab' 'User crontab' 'Login hook' 'Global login items' 'User login items' 'Safari extensions' 'Restricted files' 'Hidden apps' );N3=${#l[@]};for i in 0 1 2;do l[N3+i]=${p[5+i]};done;N4=${#l[@]};for j in 0 1;do l[N4+j]="Average ${p[29+j]}stream data (KiB/s)";l[N4+2+j]="Current ${p[29+j]}stream data";done;A0(){ id -G|grep -qw 80;v[1]=$?;((v[1]==0))&&sudo true;v[2]=$?;v[3]=`date +%s`;clear;v[11]=$((v[3]-`sysctl -n kern.boottime|cut -c9-18`));};for i in 0 1;do for j in 0 1;do eval A$((1+i+2*j))"${p[39]}${p[35+j]}${p[40]}${c1[30+i]}${p[41]}${p[37+j]}${p[42]}";done;eval A$((5+i))'(){ v[0]=`while read i;do eval "${c1[$1]} ${c2[$2]}" \"$i\"|'${c1[30+i]}' "${s[$3]}";done<<<"${v[$4]}"`;[[ "${v[0]}" ]];};';eval A$((7+i))'(){ v[0]=`while read i;do '${c1[30+i]}' "${s[$1]}" "$i";done<<<"${v[$2]}"`;[[ "${v[0]}" ]];};';done;A9(){ v[0]=$((`date +%s`-v[3]));};B00(){ v[0]=${a[++ind]};};for j in 0 1; do eval B0$((1+j))'(){ v[0]=$((v[0]'${p[26+j]}'p[$1]?v[0]:0));};';eval B0$((3+j))'(){ a[$1]=${a[$1]%[.+-]*};((a[$1]'${p[26+j]}'p[$2]))||unset a;};';done;B05(){ v[0]=`tail -n${p[$1]}<<<"${v[0]}"`;};B06(){ [[ "${a[*]}" ]]&&a=("${a[$1]}" "${a[$2]}");};B07(){ unset a v[0] ind;((v[2]==0))||{ v[0]=No;false;};};B08(){ v[$1]="${v[0]}";};B09(){ a=(${v[0]});};B10(){ v[0]=`grep -F "${v[$1]}"<<<"${v[0]}"`;};B11(){ n=$((${#a[@]}-1));((n>2))||return;A="${a[*]}";B="${a[n-1]} ${a[n]}";a=("${A% $B}" $B);};B12(){ v[0]=;[[ "$a" ]]&&v[0]="$a (UID ${a[1]}) is using ${a[2]}${p[$1]}";};B13(){ v[0]=$((v[0]/v[$1]));};B14(){ v[$2]=`eval "sed -En '${s[$3]}'"<<<"${v[$1]}"`;};B15(){ v[$2]=`eval "awk '${s[$3]}'"<<<"${v[$1]}"`;};B16(){ v[$1]="${v[$1]}"$'\n'"${v[$2]}";};B17(){ v[0]=`paste -d: <(echo "${v[$1]}") <(echo "${v[$2]}")|awk -F: '{printf("'"${f[$3]}"'",$1,$2)}'`;};B18(){ unset a v[0] ind;((v[1]==0))||{ v[0]=No;false;};};B19(){ v[0]="${a[++ind]}";};B20(){ v[0]=`grep -Fv "${v[$1]}"<<<"${v[0]}"`;};C0(){ echo $'\n'"${v[0]}";};C1(){ [[ "${v[0]}" ]]&&printf "${f[$1]}" "${l[$2]}" "${v[0]}";};C2(){ v[0]=`echo ${v[0]}`;[[ "${v[0]}" != 0 ]]&&C1 0 $1;};C3(){ v[0]=`sed -E "${s[0]}"<<<"${v[0]}"`&&C1 1 $1;};C4(){ [[ "${a[*]}" ]]&&printf "${f[$1]}" "${l[$2]}" "${a[@]}";};A0;{ B18;C2 27;B18&&! B07&&C2 28;A1 15 37 25;C2 8;A1 0 $N1 1;C0;A3 0 $((N1+1)) 2;C2 0;B00;B01 10;C2 1;A1 0 $((N1+2)) 3;C3 2;A1 0 $((N1+3)) 4;C3 3;A3 0 $((N1+4)) 5;B02 11;C2 4;B00;C2 5;for i in 0 1 2;do A1 0 $((N1+5+i)) 6;C3 $((N3+i));done;A1 1 10 7;C3 9;A1 1 11 8;C3 10;A2 2 12 9;C2 11;A1 3 13 10;C2 12;A1 4 19 11;B15 0 0 54;C3 13;A2 5 14 12;B05 12;C3 14;A2 6 36 13;B01 13;C2 15;A2 7 37 14;B02 15;C2 16;A3 8 15 15;B03 4 16;B06 1 3;C4 3 17&&{ A3 9 16 16;B11;B12 17;C2 18;};A2 10 38 17;B02 18;C2 19;B07&&{ A2 11 17 17;B05 19;B09;B11;B04 2 19;B12 20;C2 20;};A3 12 39 15;B11;B04 2 21;B12 22;C2 21;A1 13 40 18;B08 4;B14 4 0 19;A5 14 6 52 0;B08 5;A1 17 41 20;B20 5;C3 22;B14 4 6 21;A5 14 7 52 6;B08 7;B14 4 0 22;A5 14 6 52 0;B08 8;B16 7 8;B07&&{ A2 19 26 23;B20 7;C3 23;};A2 18 26 23;B20 7;C3 24;A1 4 20 21;B20 6;B08 9;A6 14 7 53 9;B08 10;B17 9 10 4;C3 25;A1 4 21 24;C3 26;B14 4 12 26;B14 4 13 27;A1 4 22 29;B20 12;B08 14;A6 14 6 53 14;B08 15;B17 14 15 4;B14 0 0 30;C3 29;A1 4 23 27;B20 13;C3 30;A1 24 24 32;C3 31;A1 23 18 28;B08 16;A2 16 25 33;B20 16;B14 0 0 34;B08 21;A8 47 21&&C0;B07&&{ A1 21 0 32;C3 43;};for i in 0 1;do A2 14 $((1+i)) 48;C3 $((44+i));done;A1 14 3 49;C3 46;A2 4 4 50;C2 47;A1 4 5 32;C3 48;A2 0 $((N1+8)) 51;C2 32;A1 4 8 55;C3 6;A2 22 9 56;C3 7;B07&&{ A1 36 42 32;C3 41;};A2 20 42 32;C3 42;A1 25 37 32;C3 33;A1 26 28 35;C2 34;A1 27 29 36;C3 35;A2 28 30 37;B08 17;A1 29 31 38;B10 17;B14 0 18 41;A2 27 32 39&&{ B08 19;A2 29 33 40;B08 20;B17 19 20 5;};C2 36;A2 29 34 42 18;C3 37;A2 32 37 43;B01 25;C2 38;A4 33 35 44 17;for i in 0 1;do B13 11;B02 $((31+i));C2 $((N4+i));B19;done;B07&&for i in 0 1;do A4 34 $((N2+i)) 45;B11;B04 3 $((31+i));B12 14;C2 $((N4+2+i));done;B07&&{ A2 35 43 46;C2 39;};A9;C2 40;} 2>/dev/null|pbcopy;exit 2>&-
Copy the selected text to the Clipboard by pressing the key combination command-C.
7. Launch the built-in Terminal application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Terminal in the icon grid.
Click anywhere in the Terminal window and paste by pressing command-V. The text you pasted should vanish immediately. If it doesn't, press the return key.
8. If you see an error message in the Terminal window such as "syntax error," enter
exec bash
and press return. Then paste the script again.
9. If you're logged in as an administrator, you'll be prompted for your login password. Nothing will be displayed when you type it. You will not see the usual dots in place of typed characters. Make sure caps lock is off. Type carefully and then press return. You may get a one-time warning to be careful. If you make three failed attempts to enter the password, the test will run anyway, but it will produce less information. In most cases, the difference is not important. If you don't know the password, or if you prefer not to enter it, press the key combination control-C or just press return three times at the password prompt. Again, the script will still run.
If you're not logged in as an administrator, you won't be prompted for a password. The test will still run. It just won't do anything that requires administrator privileges.
10. The test may take a few minutes to run, depending on how many files you have and the speed of the computer. A computer that's abnormally slow may take longer to run the test. While it's running, there will be nothing in the Terminal window and no indication of progress. Wait for the line
[Process completed]
to appear. If you don't see it within half an hour or so, the test probably won't complete in a reasonable time. In that case, close the Terminal window and report the results. No harm will be done.
11. When the test is complete, quit Terminal. The results will have been copied to the Clipboard automatically. They are not shown in the Terminal window. Please don't copy anything from there. All you have to do is start a reply to this comment and then paste by pressing command-V again.
At or near the top of the results, there will be a line that begins with "System Version." If you don't see that, but instead see a mass of gibberish, you didn't wait for the "Process completed" message to appear in the Terminal window. Please wait for it and try again.
If any private information, such as your name or email address, appears in the results, anonymize it before posting. Usually that won't be necessary.
12. When you post the results, you might see the message, "You have included content in your post that is not permitted." It means that the forum software has misidentified something in the post as a violation of the rules. If that happens, please post the test results on Pastebin, then post a link here to the page you created.
Note: This is a public forum, and others may give you advice based on the results of the test. They speak only for themselves, and I don't necessarily agree with them.
Copyright © 2014 by Linc Davis. As the sole author of this work, I reserve all rights to it except as provided in the Use Agreement for the Apple Support Communities website ("ASC"). Readers of ASC may copy it for their own personal use. Neither the whole nor any part may be redistributed. -
My macbook pro started running very slow in the past few days
Don't know if freezes or run very slow, it always happen when i open the mac (i always leave it on sleep mode) it doesn't respond to anything and the cursor turns into the rainbow loading icon.
It takes like ten to twenty minutes to respond if i've clicked on safari or any aplication to open.
The solution i found to that was keep pressing the power button til the mac turn off , restarting seemed to solve the problem but now it took like 30 minutes to restart, when always was like 5 minutes.
What can i do?If you get your machine running, you should immediatly copy off any personal data to a Storage Drive (no TimeMachine!) because your boot drive is failing.
See emergency quick copy here
Most commonly used backup methods
If you have a copy of your data off the machine, if your able too you can replace the drive yourself or if under AppleCare or warranty take it in for service.
Install/upgrade RAM or storage drive in Mac's
Since you've upgraded to 10.7 on that machine, you have to make a Recovery USB or borrow a friends machine andcopy theirs, perhaps Apple will let you get a copy.
http://osxdaily.com/2011/08/08/lion-recovery-disk-assistant-tool-makes-external- lion-boot-recovery-drives/
It's because Recovery HD is used to reinstall 10.7+ on a new boot drive. Newer machines have Internet Recovery.
https://support.apple.com/kb/HT4718
Or else fresh install 10.6 from your disks and then option click on Purchases to redownload and install 10.7
How to erase and install Snow Leopard 10.6 -
Mac Pro laptop running very slow and freezing often
Recently my Mac has been acting funny. I will be surfing the net or just trying to check my email and the spinning wheel will come up and spin forever. Sometimes it stops and lets me continue, sometimes and stops for a few minutes and does it again, other times I have to restart the computer. I have plently of memory left. I have checked to see what programs are running, etc and nothing looks abnormal. However when I created a new user - everything works fine. So question - how do I fix my user so that works just as good as the new user?
How are checking your emails? I had a similar problem but surfing the web with Safari, then I discovered that there was an update for Safari, updated and the problem is gone. Working great.
-
Macbook Pro suddenly started running very slow
Hello All,
My Macbook Pro is running very slow for the past 2 days. Did disk repair, Erasing free space, deleted a lot of unwanted files and also restarting my machine multiple times. Kindly suggest a solution for my problem. Please find my ETRE check details below,
EtreCheck version: 1.9.15 (52)
Report generated September 1, 2014 at 11:21:27 PM GMT+10
Hardware Information: ?
MacBook Pro (13-inch, Early 2011) (Verified)
MacBook Pro - model: MacBookPro8,1
1 2.3 GHz Intel Core i5 CPU: 2 cores
8 GB RAM
Video Information: ?
Intel HD Graphics 3000 - VRAM: 512 MB
Color LCD 1280 x 800
System Software: ?
OS X 10.9.4 (13E28) - Uptime: 0 days 0:8:46
Disk Information: ?
TOSHIBA MK3265GSXF disk0 : (320.07 GB)
S.M.A.R.T. Status: Verified
EFI (disk0s1) <not mounted>: 209.7 MB
Macintosh HD (disk0s2) / [Startup]: 319.21 GB (69.49 GB free)
Recovery HD (disk0s3) <not mounted>: 650 MB
OPTIARC DVD RW AD-5970H
USB Information: ?
Apple Inc. FaceTime HD Camera (Built-in)
Apple Inc. BRCM2070 Hub
Apple Inc. Bluetooth USB Host Controller
Apple Inc. Apple Internal Keyboard / Trackpad
Apple Computer, Inc. IR Receiver
Thunderbolt Information: ?
Apple Inc. thunderbolt_bus
Gatekeeper: ?
Mac App Store and identified developers
Kernel Extensions: ?
[not loaded] com.ZTE.driver.ModemDriverMac (1.0.2d1) Support
[not loaded] com.seagate.driver.PowSecDriverCore (5.0.1) Support
[not loaded] com.seagate.driver.PowSecLeafDriver_10_4 (5.0.1) Support
[not loaded] com.seagate.driver.PowSecLeafDriver_10_5 (5.0.1) Support
[not loaded] com.seagate.driver.SeagateDriveIcons (5.0.1) Support
Startup Items: ?
EyeConnect: Path: /Library/StartupItems/EyeConnect
Problem System Launch Agents: ?
[loaded] com.paragon.NTFS.auth.plist Support
Launch Daemons: ?
[loaded] com.adobe.fpsaud.plist Support
[loaded] com.google.keystone.daemon.plist Support
[loaded] com.microsoft.office.licensing.helper.plist Support
[loaded] com.oracle.java.JavaUpdateHelper.plist Support
[running] com.parallels.desktop.launchdaemon.plist Support
[not loaded] com.teamviewer.teamviewer_service.plist Support
[failed] com.tvmobili.tvmobilisvcd.plist Support
Launch Agents: ?
[not loaded] com.adobe.AAM.Updater-1.0.plist Support
[running] com.canon.MFManager.plist Support
[loaded] com.citrix.AuthManager_Mac.plist Support
[running] com.citrix.ReceiverHelper.plist Support
[running] com.citrix.ServiceRecords.plist Support
[loaded] com.google.keystone.agent.plist Support
[failed] com.parallels.desktop.launch.plist Support
[loaded] com.parallels.DesktopControlAgent.plist Support
[running] com.parallels.vm.prl_pcproxy.plist Support
[running] com.seagate.SeagateStorageGauge.plist Support
[not loaded] com.teamviewer.teamviewer.plist Support
[not loaded] com.teamviewer.teamviewer_desktop.plist Support
[failed] com.tvmobili.artwork.plist Support
User Launch Agents: ?
[loaded] com.adobe.AAM.Updater-1.0.plist Support
[loaded] com.adobe.ARM.[...].plist Support
[failed] com.apple.CSConfigDotMacCert-[...]@me.com-SharedServices.Agent.plist
User Login Items: ?
iTunesHelper
Dropbox
SwitchResX Daemon
Android File Transfer Agent
Google Chrome
Actions Server
Content Manager Assistant
Internet Plug-ins: ?
LogitechHarmony: Version: 1.0.0.1 Support
JavaAppletPlugin: Version: Java 7 Update 67 Check version
o1dbrowserplugin: Version: 5.4.2.18903 Support
Default Browser: Version: 537 - SDK 10.9
Flip4Mac WMV Plugin: Version: 2.4.0.11 Support
net.juniper.DSSafariExtensions: Version: (null) Support
AdobePDFViewerNPAPI: Version: 11.0.07 - SDK 10.6 Support
FlashPlayer-10.6: Version: 14.0.0.176 - SDK 10.6 Support
Silverlight: Version: 5.1.10411.0 - SDK 10.6 Support
Flash Player: Version: 14.0.0.176 - SDK 10.6 Support
QuickTime Plugin: Version: 7.7.3
CitrixICAClientPlugIn: Version: 11.8.2 - SDK 10.7 Support
googletalkbrowserplugin: Version: 5.4.2.18903 Support
AdobePDFViewer: Version: 11.0.07 - SDK 10.6 Support
SharePointBrowserPlugin: Version: 14.4.1 - SDK 10.6 Support
DirectorShockwave: Version: 11.6.6r636 Support
Audio Plug-ins: ?
BluetoothAudioPlugIn: Version: 1.0 - SDK 10.9
AirPlay: Version: 2.0 - SDK 10.9
AppleAVBAudio: Version: 203.2 - SDK 10.9
iSightAudio: Version: 7.7.3 - SDK 10.9
iTunes Plug-ins: ?
Quartz Composer Visualizer: Version: 1.4 - SDK 10.9
User Internet Plug-ins ?
Picasa: Version: 1.0 Support
3rd Party Preference Panes: ?
Application Enhancer Support
EyeConnect
Flash Player Support
Paragon NTFS for Mac ® OS X Support
Time Machine: ?
Auto backup: YES
Volumes being backed up:
Macintosh HD: Disk size: 297.29 GB Disk used: 232.58 GB
Destinations:
TOSHIBA EXT [Local] (Last used)
Total size: 2 TB
Total number of backups: 12
Oldest backup: 2014-02-26 14:51:47 +0000
Last backup: 2014-07-22 12:36:09 +0000
Size of backup disk: Excellent
Backup size 2 TB > (Disk size 297.29 GB X 3)
Time Machine details may not be accurate.
All volumes being backed up may not be listed.
Top Processes by CPU: ?
10% CCleaner
7% Safari
4% WindowServer
2% Finder
2% prl_disp_service
Top Processes by Memory: ?
123 MB com.apple.IconServicesAgent
98 MB Safari
82 MB EyeConnect
82 MB CCleaner
74 MB Finder
Virtual Memory Information: ?
4.95 GB Free RAM
1.48 GB Active RAM
346 MB Inactive RAM
1.23 GB Wired RAM
317 MB Page-ins
0 B Page-outs1. This procedure is a diagnostic test. It changes nothing, for better or worse, and therefore will not, in itself, solve the problem. But with the aid of the test results, the solution may take a few minutes, instead of hours or days.
Don't be put off merely by the seeming complexity of these instructions. The process is much less complicated than the description. You do harder tasks with the computer all the time.
2. If you don't already have a current backup, back up all data before doing anything else. The backup is necessary on general principle, not because of anything in the test procedure. Backup is always a must, and when you're having any kind of trouble with the computer, you may be at higher than usual risk of losing data, whether you follow these instructions or not.
There are ways to back up a computer that isn't fully functional. Ask if you need guidance.
3. Below are instructions to run a UNIX shell script, a type of program. As I wrote above, it changes nothing. It doesn't send or receive any data on the network. All it does is to generate a human-readable report on the state of the computer. That report goes nowhere unless you choose to share it. If you prefer, you can read it yourself without disclosing the contents to me or anyone else.
You should be wondering whether you can believe me, and whether it's safe to run a program at the behest of a stranger. In general, no, it's not safe and I don't encourage it.
In this case, however, there are a couple of ways for you to decide whether the program is safe without having to trust me. First, you can read it. Unlike an application that you download and click to run, it's transparent, so anyone with the necessary skill can verify what it does.
You may not be able to understand the script yourself. But variations of the script have been posted on this website thousands of times over a period of years. The site is hosted by Apple, which does not allow it to be used to distribute harmful software. Any one of the millions of registered users could have read the script and raised the alarm if it was harmful. Then I would not be here now and you would not be reading this message.
Nevertheless, if you can't satisfy yourself that these instructions are safe, don't follow them. Ask for other options.
4. Here's a summary of what you need to do, if you choose to proceed:
☞ Copy a line of text in this window to the Clipboard.
☞ Paste into the window of another application.
☞ Wait for the test to run. It usually takes a few minutes.
☞ Paste the results, which will have been copied automatically, back into a reply on this page.
The sequence is: copy, paste, wait, paste again. You don't need to copy a second time. Details follow.
5. You may have started the computer in "safe" mode. Preferably, these steps should be taken in “normal” mode, under the conditions in which the problem is reproduced. If the system is now in safe mode and works well enough in normal mode to run the test, restart as usual. If you can only test in safe mode, do that.
6. If you have more than one user, and the one affected by the problem is not an administrator, then please run the test twice: once while logged in as the affected user, and once as an administrator. The results may be different. The user that is created automatically on a new computer when you start it for the first time is an administrator. If you can't log in as an administrator, test as the affected user. Most personal Macs have only one user, and in that case this section doesn’t apply. Don't log in as root.
7. The script is a single long line, all of which must be selected. You can accomplish this easily by triple-clicking anywhere in the line. The whole line will highlight, though you may not see all of it in the browser window, and you can then copy it. If you try to select the line by dragging across the part you can see, you won't get all of it.
Triple-click anywhere in the line of text below on this page to select it:
PATH=/usr/bin:/bin:/usr/sbin:/sbin:/usr/libexec;clear;cd;p=(Software Hardware Memory Diagnostics Power FireWire Thunderbolt USB Fonts SerialATA 4 1000 25 5120 KiB/s 1024 85 \\b%% 20480 1 MB/s 25000 ports ' com.clark.\* \*dropbox \*GoogleDr\* \*k.AutoCAD\* \*k.Maya\* vidinst\* ' DYLD_INSERT_LIBRARIES\ DYLD_LIBRARY_PATH -86 "` route -n get default|awk '/e:/{print $2}' `" 25 N\\/A down up 102400 25600 recvfrom sendto CFBundleIdentifier 25 25 25 1000 MB com.apple.AirPortBaseStationAgent 464843899 51 5120 files );N5=${#p[@]};p[N5]=` networksetup -listnetworkserviceorder|awk ' NR>1 { sub(/^\([0-9]+\) /,"");n=$0;getline;} $NF=="'${p[26]}')" { sub(/.$/,"",$NF);print n;exit;} ' `;f=('\n%s: %s\n' '\n%s\n\n%s\n' '\nRAM details\n%s\n' %s\ %s '%s\n-\t%s\n' );S0() { echo ' { q=$NF+0;$NF="";u=$(NF-1);$(NF-1)="";gsub(/^ +| +$/,"");if(q>='${p[$1]}') printf("%s (UID %s) is using %s '${p[$2]}'",$0,u,q);} ';};s=(' /^ *$|CSConfigDot/d;s/^ */ /;s/[-0-9A-Fa-f]{22,}/UUID/g;s/(ochat)\.[^.]+(\..+)/\1\2/;/Shared/!s/\/Users\/[^/]+/~/g ' ' s/^ +//;/de: S|[nst]:/p;' ' {sub(/^ +/,"")};/er:/;/y:/&&$2<'${p[10]} ' 1s/://;3,6d;/[my].+:/d;s/^ {4}//;H;${ g;s/\n$//;/s: [^EO]|x([^08]|02[^F]|8[^0])/p;} ' ' 5h;6{ H;g;/P/!p;} ' ' ($1~/^Cy/&&$3>'${p[11]}')||($1~/^Cond/&&$2!~/^N/) ' ' /:$/{ N;/:.+:/d;s/ *://;b0'$'\n'' };/^ *(V.+ [0N]|Man).+ /{ s/ 0x.... //;s/[()]//g;s/(.+: )(.+)/ (\2)/;H;};$b0'$'\n'' d;:0'$'\n'' x;s/\n\n//;/Apple[ ,]|Genesy|Intel|SMSC/d;s/\n.*//;/\)$/p;' ' s/^.*C/C/;H;${ g;/No th|pms/!p;} ' '/= [^GO]/p' '{$1=""};1' ' /Of/!{ s/^.+is |\.//g;p;} ' ' $0&&!/ / { n++;print;} END { if(n<200) print "com.apple.";} ' ' $3~/[0-9]:[0-9]{2}$/ { gsub(/:[0-9:a-f]{14}/,"");} { print|"tail -n'${p[12]}'";} ' ' NR==2&&$4<='${p[13]}' { print $4;} ' ' END { $2/=256;if($2>='${p[15]}') print int($2) } ' ' NR!=13{next};{sub(/[+-]$/,"",$NF)};'"`S0 21 22`" 'NR!=2{next}'"`S0 37 17`" ' NR!=5||$8!~/[RW]/{next};{ $(NF-1)=$1;$NF=int($NF/10000000);for(i=1;i<=3;i++){$i="";$(NF-1-i)="";};};'"`S0 19 20`" 's:^:/:p' '/\.kext\/(Contents\/)?Info\.plist$/p' 's/^.{52}(.+) <.+/\1/p' ' /Launch[AD].+\.plist$/ { n++;print;} END { print "'${p[41]}'";if(n<200) print "/System/";} ' '/\.xpc\/(Contents\/)?Info\.plist$/p' ' NR>1&&!/0x|\.[0-9]+$|com\.apple\.launchctl\.(Aqua|Background|System)$|'${p[41]}'/ { print $3;} ' ' /\.(framew|lproj)|\):/d;/plist:|:.+(Mach|scrip)/s/:[^:]+//p ' '/^root$/p' ' !/\/Contents\/.+\/Contents|Applic|Autom|Frameworks/&&/Lib.+\/Info.plist$/ { n++;print;} END { if(n<1100) print "/System/";} ' '/^\/usr\/lib\/.+dylib$/p' ' /Temp|emac/{next};/(etc|Preferences|Launch[AD].+)\// { sub(".(/private)?","");n++;print;} END { print "'${p[41]}'.plist\t'${p[42]}'";if(n<500) print "Launch";} ' ' /\/(Contents\/.+\/Contents|Frameworks)\/|\.wdgt\/.+\.([bw]|plu)/d;p;' 's/\/(Contents\/)?Info.plist$//;p' ' { gsub("^| |\n","\\|\\|kMDItem'${p[35]}'=");sub("^...."," ") };1 ' p '{print $3"\t"$1}' 's/\'$'\t''.+//p' 's/1/On/p' '/Prox.+: [^0]/p' '$2>'${p[43]}'{$2=$2-1;print}' ' BEGIN { i="'${p[26]}'";M1='${p[16]}';M2='${p[18]}';M3='${p[31]}';M4='${p[32]}';} !/^A/{next};/%/ { getline;if($5<M1) a="user "$2"%, system "$4"%";} /disk0/&&$4>M2 { b=$3" ops/s, "$4" blocks/s";} $2==i { if(c) { d=$3+$4+$5+$6;next;};if($4>M3||$6>M4) c=int($4/1024)" in, "int($6/1024)" out";} END { if(a) print "CPU: "a;if(b) print "I/O: "b;if(c) print "Net: "c" (KiB/s)";if(d) print "Net errors: "d" packets/s";} ' ' /r\[0\] /&&$NF!~/^1(0|72\.(1[6-9]|2[0-9]|3[0-1])|92\.168)\./ { print $NF;exit;} ' ' !/^T/ { printf "(static)";exit;} ' '/apsd|BKAg|OpenD/!s/:.+//p' ' (/k:/&&$3!~/(255\.){3}0/ )||(/v6:/&&$2!~/A/ ) ' ' $1~"lR"&&$2<='${p[25]}';$1~"li"&&$3!~"wpa2";' ' BEGIN { FS=":";p="uniq -c|sed -E '"'s/ +\\([0-9]+\\)\\(.+\\)/\\\2 x\\\1/;s/x1$//'"'";} { n=split($3,a,".");sub(/_2[01].+/,"",$3);print $2" "$3" "a[n]$1|p;b=b$1;} END { close(p) if(b) print("\n\t* Code injection");} ' ' NR!=4{next} {$NF/=10240} '"`S0 27 14`" ' END { if($3~/[0-9]/)print$3;} ' ' BEGIN { L='${p[36]}';} !/^[[:space:]]*(#.*)?$/ { l++;if(l<=L) f=f"\n "$0;} END { F=FILENAME;if(!F) exit;if(!f) f="\n [N/A]";"file -b "F|getline T;if(T!~/^(AS.+ (En.+ )?text$|(Bo|PO).+ sh.+ text ex)/) F=F" ("T")";printf("\nContents of %s\n%s\n",F,f);if(l>L) printf("\n ...and %s more line(s)\n",l-L);} ' ' /^ +[NP].+ =/h;/^( +D.+[{]|[}])/{ g;s/.+= //p;};' 's/0/Off/p' ' END{print NR} ' ' /id: N|te: Y/{i++} END{print i} ' ' / / { print "'"${p[28]}"'";exit;};1;' '/ en/!s/\.//p' ' NR!=13{next};{sub(/[+-M]$/,"",$NF)};'"`S0 39 40`" ' $10~/\(L/&&$9!~"localhost" { sub(/.+:/,"",$9);print $1": "$9;} ' '/^ +r/s/.+"(.+)".+/\1/p' 's/(.+\.wdgt)\/(Contents\/)?Info\.plist$/\1/p' 's/^.+\/(.+)\.wdgt$/\1/p' ' /l: /{ /DVD/d;s/.+: //;b0'$'\n'' };/s: /{ /V/d;s/^ */- /;H;};$b0'$'\n'' d;:0'$'\n'' x;/APPLE [^:]+$/d;p;' ' /^find: /d;p;' "`S0 44 45`" );c1=(system_profiler pmset\ -g nvram fdesetup find syslog df vm_stat sar ps sudo\ crontab sudo\ iotop top pkgutil 'PlistBuddy 2>&1 -c "Print' whoami cksum kextstat launchctl sudo\ launchctl crontab 'sudo defaults read' stat lsbom mdfind ' for i in ${p[24]};do ${c1[18]} ${c2[27]} $i;done;' defaults\ read scutil sudo\ dtrace sudo\ profiles sed\ -En awk /S*/*/P*/*/*/C*/*/airport networksetup mdutil sudo\ lsof test );c2=(com.apple.loginwindow\ LoginHook '" /L*/P*/loginw*' '" L*/P*/*loginit*' 'L*/Ca*/com.ap*.Saf*/E*/* -d 1 -name In*t -exec '"${c1[14]}"' :CFBundleDisplayName" {} \;|sort|uniq' '~ $TMPDIR.. \( -flags +sappnd,schg,uappnd,uchg -o ! -user $UID -o ! -perm -600 \)' '.??* -path .Trash -prune -o -type d -name *.app -print -prune' :${p[35]}\" :Label\" '{/,}L*/{Con,Pref}* -type f ! -size 0 -name *.plist -exec plutil -s {} \;' "-f'%N: %l' Desktop L*/Keyc*" therm sysload boot-args status " -F '\$Time \$Message' -k Sender kernel -k Message Req 'bad |Beac|caug|dead[^bl]|FAIL|fail|GPU |hfs: Ru|inval|jnl:|last value [1-9]|n Cause: -|NVDA\(|pagin|proc: t|Roamed|rror|ssert|Thrott|tim(ed? ?|ing )o|WARN' -k Message Rne 'Goog|ksadm|SMC:| VALI|xpma' -o -k Sender fseventsd -k Message Req 'SL' " '-du -n DEV -n EDEV 1 10' 'acrx -o comm,ruid,%cpu' '-t1 10 1' '-f -pfc /var/db/r*/com.apple.*.{BS,Bas,Es,J,OSXU,Rem,up}*.bom' '{/,}L*/Lo*/Diag* -type f -regex .\*[cgh] ! -name *ag \( -exec grep -lq "^Thread c" {} \; -exec printf \* \; -o -true \) -execdir stat -f:%Sc:%N -t%F {} \;|sort -t: -k2 |tail -n'${p[38]} '-L {/{S*/,},}L*/Lau* -type f' '-L /{S*/,}L*/StartupItems -type f -exec file {} +' '-L /S*/L*/{C*/Sec*A,E}* {/,}L*/{A*d,Ca*/*/Ex,Co{mpon,reM},Ex,Inter,iTu*/*P,Keyb,Mail/B,Pr*P,Qu*T,Scripti,Sec,Servi,Spo,Widg}* -path \\*s/Resources -prune -o -type f -name Info.plist' '/usr/lib -type f -name *.dylib' `awk "${s[31]}"<<<${p[23]}` "/e*/{auto,{cron,fs}tab,hosts,{[lp],sy}*.conf,pam.d/*,ssh{,d}_config,*.local} {,/usr/local}/etc/periodic/*/* /L*/P*{,/*}/com.a*.{Bo,sec*.ap}*t /S*/L*/Lau*/*t .launchd.conf" list getenv /Library/Preferences/com.apple.alf\ globalstate --proxy '-n get default' -I --dns -getdnsservers\ "${p[N5]}" -getinfo\ "${p[N5]}" -P -m\ / '' -n1 '-R -l1 -n1 -o prt -stats command,uid,prt' '--regexp --only-files --files com.apple.pkg.*|sort|uniq' -kl -l -s\ / '-R -l1 -n1 -o mem -stats command,uid,mem' '+c0 -i4TCP:0-1023' com.apple.dashboard\ layer-gadgets '-d /L*/Mana*/$USER&&echo On' '-app Safari WebKitDNSPrefetchingEnabled' "+c0 -l|awk '{print(\$1,\$3)}'|sort|uniq -c|sort -n|tail -1|awk '{print(\$2,\$3,\$1)}'" );N1=${#c2[@]};for j in {0..9};do c2[N1+j]=SP${p[j]}DataType;done;N2=${#c2[@]};for j in 0 1;do c2[N2+j]="-n ' syscall::'${p[33+j]}':return { @out[execname,uid]=sum(arg0) } tick-10sec { trunc(@out,1);exit(0);} '";done;l=(Restricted\ files Hidden\ apps 'Elapsed time (s)' POST Battery Safari\ extensions Bad\ plists 'High file counts' User Heat System\ load boot\ args FileVault Diagnostic\ reports Log 'Free space (MiB)' 'Swap (MiB)' Activity 'CPU per process' Login\ hook 'I/O per process' Mach\ ports kexts Daemons Agents launchd Startup\ items Admin\ access Root\ access Bundles dylibs Apps Font\ issues Inserted\ dylibs Firewall Proxies DNS TCP/IP Wi-Fi Profiles Root\ crontab User\ crontab 'Global login items' 'User login items' Spotlight Memory Listeners Widgets Parental\ Controls Prefetching SATA Descriptors );N3=${#l[@]};for i in 0 1 2;do l[N3+i]=${p[5+i]};done;N4=${#l[@]};for j in 0 1;do l[N4+j]="Current ${p[29+j]}stream data";done;A0() { id -G|grep -qw 80;v[1]=$?;((v[1]==0))&&sudo true;v[2]=$?;v[3]=`date +%s`;clear >&-;date '+Start time: %T %D%n';};for i in 0 1;do eval ' A'$((1+i))'() { v=` eval "${c1[$1]} ${c2[$2]}"|'${c1[30+i]}' "${s[$3]}" `;[[ "$v" ]];};A'$((3+i))'() { v=` while read i;do [[ "$i" ]]&&eval "${c1[$1]} ${c2[$2]}" \"$i\"|'${c1[30+i]}' "${s[$3]}";done<<<"${v[$4]}" `;[[ "$v" ]];};A'$((5+i))'() { v=` while read i;do '${c1[30+i]}' "${s[$1]}" "$i";done<<<"${v[$2]}" `;[[ "$v" ]];};';done;A7(){ v=$((`date +%s`-v[3]));};B2(){ v[$1]="$v";};for i in 0 1;do eval ' B'$i'() { v=;((v['$((i+1))']==0))||{ v=No;false;};};B'$((3+i))'() { v[$2]=`'${c1[30+i]}' "${s[$3]}"<<<"${v[$1]}"`;} ';done;B5(){ v[$1]="${v[$1]}"$'\n'"${v[$2]}";};B6() { v=` paste -d: <(printf "${v[$1]}") <(printf "${v[$2]}")|awk -F: ' {printf("'"${f[$3]}"'",$1,$2)} ' `;};B7(){ v=`grep -Fv "${v[$1]}"<<<"$v"`;};C0(){ [[ "$v" ]]&&echo "$v";};C1() { [[ "$v" ]]&&printf "${f[$1]}" "${l[$2]}" "$v";};C2() { v=`echo $v`;[[ "$v" != 0 ]]&&C1 0 $1;};C3() { v=`sed -E "$s"<<<"$v"`&&C1 1 $1;};for i in 1 2;do for j in 0 2 3;do eval D$i$j'(){ A'$i' $1 $2 $3; C'$j' $4;};';done;done;{ A0;D20 0 $((N1+1)) 2;D10 0 $N1 1;B0;C2 27;B0&&! B1&&C2 28;D12 15 37 25 8;A1 0 $((N1+2)) 3;C0;D13 0 $((N1+3)) 4 3;D23 0 $((N1+4)) 5 4;D13 0 $((N1+9)) 59 50;for i in 0 1 2;do D13 0 $((N1+5+i)) 6 $((N3+i));done;D13 1 10 7 9;D13 1 11 8 10;D22 2 12 9 11;D12 3 13 10 12;D23 4 19 44 13;D23 5 14 12 14;D22 6 36 13 15;D22 7 37 14 16;D23 8 15 38 17;D22 9 16 16 18;B1&&{ D22 35 49 61 51;D22 11 17 17 20;for i in 0 1;do D22 28 $((N2+i)) 45 $((N4+i));done;};D22 12 44 54 45;D22 12 39 15 21;A1 13 40 18;B2 4;B3 4 0 19;A3 14 6 32 0;B4 0 5 11;A1 17 41 20;B7 5;C3 22;B4 4 6 21;A3 14 7 32 6;B4 0 7 11;B3 4 0 22;A3 14 6 32 0;B4 0 8 11;B5 7 8;B1&&{ A2 19 26 23;B7 7;C3 23;};A2 18 26 23;B7 7;C3 24;A2 4 20 21;B7 6;B2 9;A4 14 7 52 9;B2 10;B6 9 10 4;C3 25;D13 4 21 24 26;B4 4 12 26;B3 4 13 27;A1 4 22 29;B7 12;B2 14;A4 14 6 52 14;B2 15;B6 14 15 4;B3 0 0 30;C3 29;A1 4 23 27;B7 13;C3 30;D13 24 24 32 31;D13 25 37 32 33;A2 23 18 28;B2 16;A2 16 25 33;B7 16;B3 0 0 34;B2 21;A6 47 21&&C0;B1&&{ D13 21 0 32 19;D13 10 42 32 40;D22 29 35 46 39;};D13 14 1 48 42;D12 34 43 53 44;D22 0 $((N1+8)) 51 32;D13 4 8 41 6;D12 26 28 35 34;D13 27 29 36 35;A2 27 32 39&&{ B2 19;A2 33 33 40;B2 20;B6 19 20 3;};C2 36;D23 33 34 42 37;B1&&D23 35 45 55 46;D23 32 31 43 38;D12 36 47 32 48;D13 20 42 32 41;D13 14 2 48 43;D13 4 5 32 1;D13 4 3 60 5;D12 26 48 49 49;B3 4 22 57;A1 26 46 56;B7 22;B3 0 0 58;C3 47;D22 4 4 50 0;D23 22 9 37 7;A7;C2 2;} 2>/dev/null|pbcopy;exit 2>&-
Copy the selected text to the Clipboard by pressing the key combination command-C.
8. Launch the built-in Terminal application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Terminal in the icon grid.
Click anywhere in the Terminal window and paste by pressing command-V. The text you pasted should vanish immediately. If it doesn't, press the return key.
9. If you see an error message in the Terminal window such as "Syntax error" or "Event not found," enter
exec bash
and press return. Then paste the script again.
10. If you're logged in as an administrator, you'll be prompted for your login password. Nothing will be displayed when you type it. You will not see the usual dots in place of typed characters. Make sure caps lock is off. Type carefully and then press return. You may get a one-time warning to be careful. If you make three failed attempts to enter the password, the test will run anyway, but it will produce less information. In most cases, the difference is not important. If you don't know the password, or if you prefer not to enter it, press the key combination control-C or just press return three times at the password prompt. Again, the script will still run.
If you're not logged in as an administrator, you won't be prompted for a password. The test will still run. It just won't do anything that requires administrator privileges.
11. The test may take a few minutes to run, depending on how many files you have and the speed of the computer. A computer that's abnormally slow may take longer to run the test. While it's running, there will be nothing in the Terminal window and no indication of progress. Wait for the line
[Process completed]
to appear. If you don't see it within half an hour or so, the test probably won't complete in a reasonable time. In that case, close the Terminal window and report what happened. No harm will be done.
12. When the test is complete, quit Terminal. The results will have been copied to the Clipboard automatically. They are not shown in the Terminal window. Please don't copy anything from there. All you have to do is start a reply to this comment and then paste by pressing command-V again.
At the top of the results, there will be a line that begins with the words "Start time." If you don't see that, but instead see a mass of gibberish, you didn't wait for the "Process completed" message to appear in the Terminal window. Please wait for it and try again.
If any private information, such as your name or email address, appears in the results, anonymize it before posting. Usually that won't be necessary.
13. When you post the results, you might see an error message on the web page: "You have included content in your post that is not permitted," or "You are not authorized to post." That's a bug in the forum software. Please post the test results on Pastebin, then post a link here to the page you created.
14. This is a public forum, and others may give you advice based on the results of the test. They speak only for themselves, and I don't necessarily agree with them.
Copyright © 2014 by Linc Davis. As the sole author of this work, I reserve all rights to it except as provided in the Use Agreement for the Apple Support Communities website ("ASC"). Readers of ASC may copy it for their own personal use. Neither the whole nor any part may be redistributed. -
Mac book pro is running very slow what can i do to speed it up?
mac book pro is running very slow what can i do to speed it up?
Things You Can Do To Resolve Slow Downs
If your computer seems to be running slower here are some things you can do:
Start with visits to: OS X Maintenance - MacAttorney;
The X Lab: The X-FAQs;
The Safe Mac » Mac Performance Guide;
The Safe Mac » The myth of the dirty Mac;
Mac maintenance Quick Assist.
Boot into Safe Mode then repair your hard drive and permissions:
Repair the Hard Drive and Permissions Pre-Lion
Boot from your OS X Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer.
Repair the Hard Drive - Lion/Mountain Lion/Mavericks
Boot to the Recovery HD:
Restart the computer and after the chime press and hold down the COMMAND and R keys until the Utilites Menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD disk icon and click on the arrow button below.
When the recovery menu appears select Disk Utility. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported, then click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the main menu. Select Restart from the Apple menu.
Restart your computer normally and see if this has helped any. Next do some maintenance:
For situations Disk Utility cannot handle the best third-party utility is Disk Warrior; DW only fixes problems with the disk directory, but most disk problems are caused by directory corruption; Disk Warrior 4.x is now Intel Mac compatible.
Note: Alsoft ships DW on a bootable DVD that will startup Macs running Snow Leopard or earlier. It cannot start Macs that came with Lion or later pre-installed, however, DW will work on those models.
Suggestions for OS X Maintenance
OS X performs certain maintenance functions that are scheduled to occur on a daily, weekly, or monthly period. The maintenance scripts run in the early AM only if the computer is turned on 24/7 (no sleep.) If this isn't the case, then an excellent solution is to download and install a shareware utility such as Macaroni, JAW PseudoAnacron, or Anacron that will automate the maintenance activity regardless of whether the computer is turned off or asleep. Dependence upon third-party utilities to run the periodic maintenance scripts was significantly reduced since Tiger. These utilities have limited or no functionality with Snow Leopard or later and should not be installed.
OS X automatically defragments files less than 20 MBs in size, so unless you have a disk full of very large files there's little need for defragmenting the hard drive.
Helpful Links Regarding Malware Protection
An excellent link to read is Tom Reed's Mac Malware Guide.
Also, visit The XLab FAQs and read Detecting and avoiding malware and spyware.
See these Apple articles:
Mac OS X Snow Leopard and malware detection
OS X Lion- Protect your Mac from malware
OS X Mountain Lion- Protect your Mac from malware
About file quarantine in OS X
If you require anti-virus protection I recommend using VirusBarrier Express 1.1.6 or Dr.Web Light both from the App Store. They're both free, and since they're from the App Store, they won't destabilize the system. (Thank you to Thomas Reed for these recommendations.)
Troubleshooting Applications
I recommend downloading a utility such as TinkerTool System, OnyX, Mavericks Cache Cleaner, or Cocktail that you can use for removing old log files and archives, clearing caches, etc. Corrupted cache, log, or temporary files can cause application or OS X crashes as well as kernel panics.
If you have Snow Leopard or Leopard, then for similar repairs install the freeware utility Applejack. If you cannot start up in OS X, you may be able to start in single-user mode from which you can run Applejack to do a whole set of repair and maintenance routines from the command line. Note that AppleJack 1.5 is required for Leopard. AppleJack 1.6 is compatible with Snow Leopard. Applejack does not work with Lion and later.
Basic Backup
For some people Time Machine will be more than adequate. Time Machine is part of OS X. There are two components:
1. A Time Machine preferences panel as part of System Preferences;
2. A Time Machine application located in the Applications folder. It is
used to manage backups and to restore backups. Time Machine
requires a backup drive that is at least twice the capacity of the
drive being backed up.
Alternatively, get an external drive at least equal in size to the internal hard drive and make (and maintain) a bootable clone/backup. You can make a bootable clone using the Restore option of Disk Utility. You can also make and maintain clones with good backup software. My personal recommendations are (order is not significant):
1. Carbon Copy Cloner
2. Get Backup
3. Deja Vu
4. SuperDuper!
5. Synk Pro
6. Tri-Backup
Visit The XLab FAQs and read the FAQ on backup and restore. Also read How to Back Up and Restore Your Files. For help with using Time Machine visit Pondini's Time Machine FAQ for help with all things Time Machine.
Referenced software can be found at MacUpdate.
Additional Hints
Be sure you have an adequate amount of RAM installed for the number of applications you run concurrently. Be sure you leave a minimum of 10% of the hard drive's capacity as free space.
Add more RAM. If your computer has less than 2 GBs of RAM and you are using OS X Leopard or later, then you can do with more RAM. Snow Leopard and Lion work much better with 4 GBs of RAM than their system minimums. The more concurrent applications you tend to use the more RAM you should have.
Always maintain at least 15 GBs or 10% of your hard drive's capacity as free space, whichever is greater. OS X is frequently accessing your hard drive, so providing adequate free space will keep things from slowing down.
Check for applications that may be hogging the CPU:
Pre-Mavericks
Open Activity Monitor in the Utilities folder. Select All Processes from the Processes dropdown menu. Click twice on the CPU% column header to display in descending order. If you find a process using a large amount of CPU time (>=70,) then select the process and click on the Quit icon in the toolbar. Click on the Force Quit button to kill the process. See if that helps. Be sure to note the name of the runaway process so you can track down the cause of the problem.
Mavericks and later
Open Activity Monitor in the Utilities folder. Select All Processes from the View menu. Click on the CPU tab in the toolbar. Click twice on the CPU% column header to display in descending order. If you find a process using a large amount of CPU time (>=70,) then select the process and click on the Quit icon in the toolbar. Click on the Force Quit button to kill the process. See if that helps. Be sure to note the name of the runaway process so you can track down the cause of the problem.
Often this problem occurs because of a corrupted cache or preferences file or an attempt to write to a corrupted log file. -
On my macbook pro I have a message on my homepage telling me that certain items want to use my keychain. I've pressed cancel the message will not go. The mac is now running very slow and iphoto and safari are not working. Can anyone help?
What version of Mac OS X?
What home page?
What browser? -
Mac book pro is running very slow. is there a way to do a disc cleanup?
mac book pro is running very slow. is there a way to do a disc cleanup?
First, back up all data immediately, as your boot drive might be failing.
Step 1
This diagnostic procedure will query the system log for messages that may indicate a hardware fault. It changes nothing, and therefore will not, in itself, solve your problem.
If you have more than one user account, these instructions must be carried out as an administrator. I've tested them only with the Safari web browser. If you use another browser, they may not work as described.
Triple-click anywhere in the line below on this page to select it:
syslog -k Sender kernel -k Message CReq 'Channel t|GPU D|I/O|n Cause: -' | tail | open -ef
Copy the selected text to the Clipboard (command-C).
Launch the Terminal application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Terminal in the icon grid.
Paste into the Terminal window (command-V).
The command may take a noticeable amount of time to run. Wait for a new line ending in a dollar sign (“$”) to appear.
A TextEdit window will open with the output of the command. Normally the command will produce no output, and the window will be empty. If the TextEdit window (not the Terminal window) has anything in it, stop here and post it — the text, please, not a screenshot. The title of the TextEdit window doesn't matter, and you don't need to post that.
Step 2
There are a few other possible causes of generalized slow performance that you can rule out easily.
Reset the System Management Controller.
If you have many image or video files on the Desktop with preview icons, move them to another folder.
If applicable, uncheck all boxes in the iCloud preference pane.
Disconnect all non-essential wired peripherals and remove aftermarket expansion cards, if any.
Check your keychains in Keychain Access for excessively duplicated items.
Boot into Recovery mode, launch Disk Utility, and run Repair Disk.
If you're booting from an aftermarket SSD, see whether there's a firmware update for it.
If you have a MacBook Pro with dual graphics, disable automatic graphics switching in the Energy Saverpreference pane for better performance at the cost of shorter battery life.
Step 3
When you notice the problem, launch the Activity Monitor application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Activity Monitor in the icon grid.
Select the CPU tab of the Activity Monitor window.
Select All Processes from the menu in the toolbar, if not already selected.
Click the heading of the % CPU column in the process table to sort the entries by CPU usage. You may have to click it twice to get the highest value at the top. What is it, and what is the process? Also post the values for % User, % System, and % Idle at the bottom of the window.
Select the System Memory tab. What values are shown in the bottom part of the window for Page outs and Swap used?
Next, select the Disk Activity tab. Post the approximate values shown for Reads in/sec and Writes out/sec (not Reads in and Writes out.)
Step 4
If you have more than one user account, you must be logged in as an administrator to carry out this step.
Launch the Console application in the same way you launched Activity Monitor. Make sure the title of the Console window is All Messages. If it isn't, select All Messages from the SYSTEM LOG QUERIES menu on the left. If you don't see that menu, select
View ▹ Show Log List
from the menu bar.
Select the 50 or so most recent entries in the log. Copy them to the Clipboard (command-C). Paste into a reply to this message (command-V). You're looking for entries at the end of the log, not at the beginning.
When posting a log extract, be selective. Don't post more than is requested.
Please do not indiscriminately dump thousands of lines from the log into this discussion.
Important: Some personal information, such as your name, may appear in the log. Anonymize before posting. That should be easy to do if your extract is not too long. -
Mac book pro is running very slow and won't connect to the Internet
Mac book pro is running very slow and won't connect to the Internet. Please help I'm rubbish with computers!
Mac book pro is running very slow and won't connect to the Internet. Please help I'm rubbish with computers!
-
My Mac book Pro is running very slow and the rainbow ball is appearing all the time. Any suggestions for clean up?? I have the OS X Lion system.
As well as what a brody asked :
- do you need more RAM? (run Activity Monitor and see how much free RAM - green - is available)
- do you Restart fairly regularly, e.g. at least once a week, to clear out any swap or temporary files?
- do you need to do maintenance, e.g. clearing out caches and unused logs, etc? -
We Recently had a few brief power failures. Since then, my Mac Pro has been very slow on startup. Any suggestions?
Like the man says:
Run Disk Utility > Repair ... (not just repair permissions) while booted from another drive. If you have a stronger utility like Disk Warrior, that would be even better.
If you find that the ONLY way you can do this is by booting from the DVD, The Hatter recommends you establish an emergency drive or partition on a drive other than the Boot drive and use that in the future. It makes emergency Repair, backup, and cloning much easier. -
My Macbook Pro started running really slow
This week my Macbook Pro started running super slow, taking ages to open programs and giving me the color wheel alllll the time. I've never had problems like this before! I'm not running many applications or doing anything unusual but it's just running extra slow. Once or twice it has also totally gone to sleep while I was in the middle of using it, and I had to wake it back up. It has also been getting really hot and the battery life seems worse...! This is all new, I'm using my computer just as I always have but it suddenly has issues.
The only thing it has been doing for a while is sometimes the screen will go blue - this either corrects itself within a few seconds or if I close my Macbook and then reopen it, the screen is back to normal. This is very rare though and I don't know if it's related to the slowness problem.
What can I do to fix this??
Mac OS X 10.6.8
2 GHz Intel Core i7
4 GB 133 MHz DDR3
I just ran EtreCheck -
Hardware Information:
MacBook Pro (15-inch, Early 2011)
MacBook Pro - model: MacBookPro8,2
1 2 GHz Intel Core i7 CPU: 4 cores
4 GB RAM
Video Information:
AMD Radeon HD 6490M - VRAM: 256 MB
Intel HD Graphics 3000 - VRAM: 384 MB
System Software:
Mac OS X 10.6.8 (10K549) - Uptime: 1 day 3:59:13
Disk Information:
Hitachi HTS725050A9A362 disk0 : (465.76 GB)
(null) (disk0s1) <not mounted>: 200 MB
Macintosh HD (disk0s2) / [Startup]: 465.44 GB (235.1 GB free)
MATSHITADVD-R UJ-898
USB Information:
Apple Inc. Apple Internal Keyboard / Trackpad
Apple Inc. BRCM2070 Hub
Apple Inc. Bluetooth USB Host Controller
Apple Inc. FaceTime HD Camera (Built-in)
Apple Computer, Inc. IR Receiver
FireWire Information:
Thunderbolt Information:
Apple, Inc. MacBook Pro
Kernel Extensions:
com.digidesign.iokit.DigiDal (8.0.3f1)
com.paceap.kext.pacesupport.snowleopard (5.7.2)
Startup Items:
DigidesignLoader: Path: /Library/StartupItems/DigidesignLoader
M-AudioFastTrack: Path: /Library/StartupItems/M-AudioFastTrack
PACESupport: Path: /Library/StartupItems/PACESupport
Problem System Launch Daemons:
[System] org.samba.winbindd.plist 3rd-Party support link
Launch Daemons:
[System] com.adobe.fpsaud.plist 3rd-Party support link
[System] com.google.keystone.daemon.plist 3rd-Party support link
[System] com.microsoft.office.licensing.helper.plist 3rd-Party support link
[System] org.eyebeam.SelfControl.plist 3rd-Party support link
[System] PACESupport.plist 3rd-Party support link
Launch Agents:
[System] com.google.keystone.agent.plist 3rd-Party support link
[System] com.hp.help.tocgenerator.plist 3rd-Party support link
[System] com.m-audio.mobilepremkii.helper.plist 3rd-Party support link
User Launch Agents:
[not loaded] com.apple.CSConfigDotMacCert-[...]@me.com-SharedServices.Agent.plist
[not loaded] com.facebook.videochat.[redacted].plist 3rd-Party support link
[not loaded] com.spotify.webhelper.plist 3rd-Party support link
User Login Items:
Flux
iTunesHelper
RescueTime
Internet Plug-ins:
o1dbrowserplugin: Version: 5.2.4.18058 3rd-Party support link
Unity Web Player: Version: UnityPlayer version 3.5.2f2 - SDK 10.6 3rd-Party support link
RealPlayer Plugin: Version: Unknown
Silverlight: Version: 5.1.20913.0 - SDK 10.6 3rd-Party support link
FlashPlayer-10.6: Version: 12.0.0.77 - SDK 10.6 3rd-Party support link
QuickTime Plugin: Version: 7.6.6
Flash Player: Version: 12.0.0.77 - SDK 10.6 3rd-Party support link
googletalkbrowserplugin: Version: 5.2.4.18058 3rd-Party support link
SharePointBrowserPlugin: Version: 14.3.9 - SDK 10.6 3rd-Party support link
AdobePDFViewer: Version: 10.1.1 3rd-Party support link
iPhotoPhotocast: Version: 7.0 - SDK 10.7
JavaAppletPlugin: Version: 13.9.8 - SDK 10.6 Outdated! Update
iTunes Plug-ins:
Quartz Composer Visualizer: Version: 1.2
3rd Party Preference Panes:
Flash Player 3rd-Party support link
Growl 3rd-Party support link
M-AudioFastTrack 3rd-Party support link
M-Audio MobilePre 3rd-Party support link
Old Applications:
None
Time Machine:
Time Machine information requires OS X 10.7 "Lion" or later.
Top Processes by CPU:
7% firefox
3% WindowServer
3% EtreCheck
2% hidd
0% coreservicesd
Top Processes by Memory:
397 MB firefox
106 MB mds
82 MB WindowServer
82 MB Mail
49 MB quicklookd
Virtual Memory Information:
1.04 GB Free RAM
1.04 GB Active RAM
1.03 GB Inactive RAM
907 MB Wired RAM
467 MB Page-ins
0 B Page-outsThe startup drive is failing, or there is some other internal hardware fault. The "etrecheck" output is irrelevant.
Back up all data on the drive immediately if you don't already have a current backup. There are ways to back up a computer that isn't fully functional — ask if you need guidance.
Make a "Genius" appointment at an Apple Store, or go to another authorized service provider.
If privacy is a concern, erase the data partition(s) with the option to write zeros* (do this only if you have at least two complete, independent backups, and you know how to restore to an empty drive from any of them.) Don’t erase the recovery partition, if present.
Keeping your confidential data secure during hardware repair
Apple also recommends that you deauthorize a device in the iTunes Store before having it serviced.
*An SSD doesn't need to be zeroed.
Maybe you are looking for
-
Cannot install Windows on my Satellite C660-162
I have a Satellite C660-162 and suddenly it was soo slow so I tried to install a new Windows but I could not install it and gives me this error Windows cannot be installed to disk 0 partition 1 or 2 and when I press it " Windows cannot be installed t
-
I have a Pages document on my iMac (Lion) that I want to copy to my iPhone4 (Verizon). I have the Pages App on my iPhone and want to edit the document on my iPhone. How do I get the document to the iPhone? I have tried moving the document to iTunes a
-
i am learning sap bw. i would like to know full details on the topic transformation in sab bw 7.0 Please search the forum before posting a thread. Edited by: Pravender on Jul 8, 2010 10:57 AM
-
with the OS 6.1.3 my Camera is not working the shutter is close out and My WiFi graied out need help Thanks
-
Imac finder slow to start - time incorrect after using windows via bootcamp
Everything works fine on my imac except for the following annoying thing that I would like to understand. After using bootcamp to use windows xp (that also works fine), after I reboot back into Macosx, "sometimes" the finder is noticeably relatively