Mac Pro trapcode particular with Cs4 install problems

hi
im on mac with leo installed.I'm trying to install particular 1.5 with cs4 but no luck so far.
it just doesnt show up in AE effects panel any ideas?
thx

There is only one installer.
No, there isn't. If downloading the original ZIP file from Red Giant Software, it contains a set of sub-folders with different versions. CS4 is intel only. Unlike CS3 it does no longer support PPC code. Therefore any such plug-ins will not show up in CS4 unless you install the correct version, which is what you do when installing from the sub-folder I mentioned. So by all means, run that installer.
Mylenium

Similar Messages

  • Hot Synch does not work, Treo 755p, USB, 17" Mac Pro Laptop, even with RevD installed and Allow other HotSynch applications preference check box checked

    Hi,
    I am a long time Palm enthusiast who is frustrated.  No more Palm products for me or anyone I speak to until I solve this problem.  Someone at Palm should be paying attention to their long time cusotmers.  I bought Palms in 2002 and 2003.
    The support literature coming with two Treo 755p that I bought was so poor that never saw the fine print that there was three months of support if I registered the devices.  The registration page does not let me register.  All the fields are ghosted after I put in the serial number.  I bought one in June 2008 and the other in early 2008.  So never registered and can get no help from Palm now it seems.
    So beside that gripe below is the problem issue info.
    I can't get a Verizon Treo 755p to USB cable Hot Synch with my daughters 17" Mac Pro Laptop.  It is using OS 10.5x  She lives in another city so I am trouble shooting this remotely.
    Did - Revd Palm upgrage has been installed.
    PalmDesktopMac421Revd.dmg (17MB)
    http://kb.palm.com/SRVS/CGI-BIN/WEBCGI.EXE/,/?St=4518,E=0000000000255177998,K=6239,Sxi=3,case=obj(33...
    Did in advanced settings on the Treo select in the Synch preferences allow other Hot Sync applications.
    That process worked however on my own Treo 755p Verizon as below:
    After much work, hours over several months, I got my my Treo 755p Verizon to Hot Synch with a QuickSilver desk top Mac running os 10.5x. 
    Did the RevD upgrade.
    Did in advanced settings on the Treo select in the Synch preferences allow other Hot Sync applications.   Otherwise the Wireless Synch feature prevents a Hot Synch.
    Once those both were done than Hot Synch works fine, and Wireless Synch works fine and does not interfere.
    The Wireless on both PDAs is scheduled to be removed on both Treos due the economy on Feb. 4th, so I would like the HotSynch to be working so her Treo is backed up.
    Thanks so much to anyone who replies to help out.
    Best
    Post relates to: Treo 755p (Verizon)
    Post relates to: Treo 755p (Verizon)
    This question was solved.
    View Solution.

    Works now, she had created a user ID as prompted when installing the HotSynch Software, but it was not the same name of the Treo 755p.  The default ID was the one she from installing the software, so it showed nothing in address or contacts, but when she switched to the Treo ID than all her stuff was there.
    Post relates to: Treo 755p (Verizon)

  • I have Outlook 2011 installed on my Mac Pro, but I can not install it icloud. I can only get through imail, iCal and Address Book in Mac native anyone know teach me how to work with Outlook 2011 icloud? thank you

    I have Outlook 2011 installed on my Mac Pro, but I can not install it icloud. I can only get through imail, iCal and Address Book in Mac native anyone know teach me how to work with Outlook 2011 icloud? thank you

    "iCloud requires iOS 5 on iPhone 3GS or later, iPod touch (3rd and 4th generation), iPad, or iPad 2; a Mac computer with OS X Lion; or a PC with Windows Vista or Windows 7 (Outlook 2007 or 2010 or an up-to-date browser is required for accessing email, contacts, and calendars). Some features require a Wi-Fi connection. Some features are not available in all countries. Access to some services is limited to 10 devices."
    From here >  http://www.apple.com/icloud/

  • My Early 2009 Mac Pro won't restart after installing Mavericks

    I have installed Mavericks on my Early 2009 Mac Pro and all seemed to install just fine but when I restart the Mac then it won't get past a grey screen with Apple logo. It seems that it does get reasonabley far into the startup, it gets passed the grey screen with cricling progress thingmy under the Apple logo, then it flashes very quickly and after that it is a grey screen with the Apple logo and no further.
    I did try installing Mavericks when it first came out and I had this problem so I just abandoned and reinstalled Mountain Lion from my Time Machine backup. However I thought that with Mavericks now at 9.1, maybe it would work okay this time but no change. However this time I do want to get it working because the lastest Final Cut Pro X requires Mavericks and I do a lot of video editing.
    Here are the things I've tried which have made no difference:
    Removed all peripherals, so that now nothing is plugged in except the original Apple Keyboard, my Apple trackpad and my Eizo monitor.
    I tried starting it in Safe Boot mode but this made no difference.
    I started it up in Recovery mode and it will start in Recovery mode. While in Recovery mode I checked the startup hard drive with Disk Utility, the drive is fine, as and I repaired disk permisions which made no difference.
    I zapped the PRAM.
    I connected it to my MacBook Pro in Target Disk mode and used ProSoft's Drive Genius 3 to check over the startup hard drive again and check disk permissions and all is well.
    It still will not startup
    I would be most grateful if someone could assist.

    Take each of these steps that you haven't already tried. Stop when the problem is resolved.
    Step 1
    The first step in dealing with a boot failure is to secure your data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since your last backup, you can skip this step.   
    There are several ways to back up a Mac that is unable to boot. You need an external hard drive to hold the backup data.
         a. Boot into the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.”
    b. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, boot the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
    c. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
    Step 2
    Sometimes a boot failure can be resolved by resetting the NVRAM.
    Step 3
    If you use a wireless keyboard, trackpad, or mouse, replace or recharge the batteries. The battery level shown in the Bluetooth menu item may not be accurate.
    Step 4
    If there's a built-in optical drive, a disc may be stuck in it. Follow these instructions to eject it.
    Step 5
    Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to boot, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can boot now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
    If you've booted from an external storage device, make sure that your internal boot volume is selected in the Startup Disk pane of System Preferences.
    Step 6
    Boot in safe mode. Note: If FileVault is enabled, or if a firmware password is set, or if the boot volume is a software RAID, you can’t do this. Post for further instructions.
    Safe mode is much slower to boot and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
    The login screen appears even if you usually log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
    When you boot in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, your boot volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 6.
    If you can boot and log in now, empty the Trash, and then open the Finder Info window on your boot volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then reboot as usual (i.e., not in safe mode.)
    If the boot process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
    Step 7
    Launch Disk Utility in Recovery mode (see Step 1.) Select your startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
    This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then reboot as usual.
    Step 8
    Reinstall the OS. If your Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
    Step 9
    Repeat Step 6, but this time erase the boot volume in Disk Utility before installing. The system should automatically reboot into the Setup Assistant. Follow the prompts to transfer your data from a Time Machine or other backup.
    Step 10
    This step applies only to older Macs (not current models) that have a logic-board ("PRAM") battery. Both desktop and portable Macs used to have such a battery. The logic-board battery, if there is one, is separate from the main battery of a portable. A dead logic-board battery can cause a boot failure. Typically the failure will be preceded by loss of the settings for the startup disk and system clock. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
    Step 11
    If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store, or go to another authorized service provider.

  • My Mac Pro (Late 2013) with an Apple SSD as the only storage will not restart

    I have a Mac Pro (Late 2013) with an APPLE SSD SM0256F as the only storage.  When I restart all I get is the spinning bars. I have to manually hold the power button down to force shutdown. I have let it try to restart for as long as 30 minutes. It will start just fine from a shutdown.  I am running Yosemite 10.10.2 (14C1510). I have used Disk Utility with no errors. The only time I need to restart is after a system upgrade. I have tried, as others have suggested, selecting the drive from the Startup Drive preferences with no difference. Any help is much appreciated!

    Try resetting the SMC and NVRAM
    Intel-based Macs: Resetting the System Management Controller (SMC)
    About NVRAM and PRAM
    Next note the time of text problem and then after reboot open the Console app and look for log entries at that time. Post suspicious ones here

  • Is it possible for Mac Pro 724 Windows xp to install?

    Is it possible for Mac Pro 724 Windows xp to install?

    I really don't like any "closed" or sealed technology.
    About half way down the page are bare 2.5" enclosures for $50 range
    http://eshop.macsales.com/shop/firewire/add-ons-and-hubs/enclosure-kits
    http://eshop.macsales.com/shop/firewire/on-the-go
    Grief! Yes, that is costly "solution" I looked on Amazon for USB2 for SATA drives and $40.
    For that kind of price, MacGurus specializes in some hot-swap FW/USB/eSATA cases so you can use it with multiple drives (giant floppy).

  • HT1338 mac pro runs slow since I installed mountain lion

    mac pro runs slow since i installed mountain lion

    First, back up all data immediately, as your boot drive might be failing.
    There are a few other possible causes of generalized slow performance that you can rule out easily.
    If you have many image or video files on the Desktop with preview icons, move them to another folder.
    If applicable, uncheck all boxes in the iCloud preference pane.
    Disconnect all non-essential wired peripherals and remove aftermarket expansion cards, if any.
    Otherwise, take the steps below when you notice the slowdown.
    Step 1
    Launch the Activity Monitor application in any of the following ways:
    ☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
    ☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
    ☞ Open LaunchPad. Click Utilities, then Activity Monitor in the icon grid.
    Select the CPU tab of the Activity Monitor window.
    Select All Processes from the menu in the toolbar, if not already selected.
    Click the heading of the % CPU column in the process table to sort the entries by CPU usage. You may have to click it twice to get the highest value at the top. What is it, and what is the process? Also post the values for % User, % System, and % Idle at the bottom of the window.
    Select the System Memory tab. What values are shown in the bottom part of the window for Page outs and Swap used?
    Next, select the Disk Activity tab. Post the approximate values shown for Reads in/sec and Writes out/sec (not Reads in and Writes out.)
    Step 2
    If you have more than one user account, you must be logged in as an administrator to carry out this step.
    Launch the Console application in the same way you launched Activity Monitor. Make sure the title of the Console window is All Messages. If it isn't, select All Messages from the SYSTEM LOG QUERIES menu on the left. If you don't see that menu, select
    View ▹ Show Log List
    from the menu bar.
    Select the 50 or so most recent entries in the log. Copy them to the Clipboard (command-C). Paste into a reply to this message (command-V). You're looking for entries at the end of the log, not at the beginning.
    When posting a log extract, be selective. Don't post more than is requested.
    Please do not indiscriminately dump thousands of lines from the log into this discussion.
    Important: Some personal information, such as your name, may appear in the log. Anonymize before posting. That should be easy to do if your extract is not too long.

  • How fast does the mac pro run xp with 3d apps

    Hi all am planing to upgrade to a mac pro, but am not sure how it will run xp and some animations softwares on the xp side,
    i was just wondering if any one knows the speed and fast the mac pro can render with 3d max mental ray. and the problems it will encounter when running xp.

    If your plan is to run XP with 3D, why not BYO and go after an Intel X58 Core i7.
    Otherwise, keep your eye on Apple Specials (ref'd) units.
    http://store.apple.com/us/browse/home/specialdeals/mac/mac_pro
    http://www.barefeats.com/harper7.html
    http://www.barefeats.com/harper.html
    Save. And hope the new Intel Core I7 "Nehalem" arrives soon.

  • I have a Mac Pro using Lion, with a SSD for system.  Restored drive from backup.  Now logon password doesn't work.  Account password still works.  Changing password in user group preferences no longer works to change logon password.

    I have a Mac Pro using Lion, with SSD for system drive.  Drive stopped booting, but otherwise appeared healthy.  Restored from system backup.  Now drive seems to work properly, BUT my logon password no longer works.  Password OK for account; can access system preferences, and change user password there BUT logon still refuses to accept password.  No luck changing password for that account after adding new administrator account and logging on from that account.  Suggestions?  Thanks.

    If you redirect Accounts to another location (not on the Boot Drive) you need to direct them back there again after a restore.
    SystemPreferences > Accounts/User&Groups > ...
    ... Unlock the lock, then hold down Control as you click on an Account to get access to the Advanced Options pane.

  • Why won't my Mac Pro sleep after Lion is installed?

    Why won't my Mac Pro sleep after Lion is installed?

    Tell us, what hardware add ons?
    old software? that required PowerPC/Rosetta maybe.
    Look for any apps, process that used powerpc and look for updates, check out RoaringApps for a table of Lion compatible programs
    does it happen iwth a clean install?
    how about if you do a Safe Boot?

  • HT201343 How can I make my 2013 Mac Pro been compatible with airplay & mirroring display

    How can I make my 2013 Mac Pro been compatible with airplay & mirroring display ?
    Thanks for any help !

    2013 Mac Pro would be compatible
    http://support.apple.com/kb/ht5404

  • With CS4 installed already, can I uninstall InDesignCS3 without affecting the CS4 suite?

    With CS4 installed already, can I uninstall InDesignCS3 without affecting the CS4 suite?
    InDesignCS3 was downloaded from the internet. CS4 suite was installed from CDs. Both are currently on my computer. How can I uninstall InDesignCS3?

    Just use the add/remove programs feature in the control panel, but I would strongly suggest that you don't do this. If you ever need to supply a CS3 file you'll be sorry you uninstalled it.
    Bob

  • Mac pro grey screen with spinning wheel

    mac pro grey screen with spinning wheel

    Gray screem appears during startup:
    http://support.apple.com/kb/TS2570?viewlocale=en_US

  • HT1338 my mac pro is running with the OS X version 10.6.8. I cloud requires version 10.7 or later. How can I update my version?

    Good evening,
    My mac pro is running with OS X version 10.6.8. I would like to update the software to the version 10.8 or later...
    Could you please let me know how can i do it?
    Thank you
    Best regards
    Giorgio

    http://www.apple.com/osx/how-to-upgrade/
    Read the system requirements carefully.
    Regards.

  • Does my new mac pro retina come with antivirus. And, for how long

    does my new mac pro retina come with antivirus? And, for how long?

    Yes it does.
    It's called OS X Lion - fully updated.
    There are no known viruses for MAC OS.
    Your current OS is your best protection
    If however, you want to feel more secured, download ClamX AV and do a scan once a week to give you peace of mind.
    Good luck

Maybe you are looking for