Mac Pro Trips an "arch vault" in the electrical outlet

Mac Pro Trips an "arch vault" in the electrical outlet causing the breaker go. This is a problem for me, sometimes when my computer sleeps and when i wake it, the power gets shut off.
The election said it's because my house outlets are setup up with a blew "arch vault" system. Which he described as neither being good, bad, or beneficial in anyway. The problem he says is when i turn on my computer it trips the "arch vault" in the outlet and it causes the breaker to shut off.
The weird thing is it some times works, and it will work after repeated attempts to turn it on, and switching back over the breaker.
My question is, does anyone know anything about this? Why does it work some times but not others? Can i buy an adapter or power bar or something to get around this annoyance. The problem is only when i turn on the mac pro. Right now i have it plugged into the bathroom (you can see the inconvenience) and the bathroom is not set up on this "arch vault" system.
any help would be much appreciated. Thank you.

It's an Arc Fault circuit breaker. They are required for bedroom circuits in new construction.
The breaker is designed to trip when it senses high frequency current pulses caused by arcing. Some electronic devices also cause them to trip. Square-D breakers are supposed to be less likely to trip with such loads. If you are using the room an an office, not a bedroom, have the breaker replaced with a standard breaker. If it is a Siemens breaker, be sure the coiled wire is still there
<http://www2.sea.siemens.com/NR/rdonlyres/20A962B3-6751-44A5-8F9E-868CC62963CB/0 /AFCIcombo144x144.jpg>

Similar Messages

  • If I put my 7300 in slot4 at 8x, and a 8800GT at slot1, 16x, could I boot 10.4.11 on my mac pro 1,1 if I unplug the monitor from the 8800GT?

    If I put my 7300 in slot4 at 8x, and a 8800GT at slot1, 16x, could I boot 10.4.11 on my mac pro 1,1 if I unplug the monitor from the 8800GT?
    I have different os's installed on my different hard drives. I'm using 10.6.8 now, but I go back to 10.5.8 and 10.4.11 on accasion. Can I run 10.4.11 with the 7300 in the 8x lane? As long as I unplug the 8800GT but leave it installed in the 16x slot1? And attach a monitor to the 7300?
    What about using the 7300 to run extra monitors or a monitor while running 10.5.8 and 10.6.8?  Is that a problem? I have 10GB Ram and the 1,1 original machine.

    I know the 8800 requires 10.5.2, but if it is installed (at 16x) but no monitor is connected, will it allow the 7300 to control one or two monitors in 10.4.11? When the 7300 is in the 8x lane? And will it boot?
    I lost part of your train of thought. Are you telling me to get just an ATI 5770 to continue using this machine into the future? 
    I thought the original mac pro 1,1 needed cards of the same manufacturer. If I use the 5770, that eliminates the ability to boot 10.4.11, correct?
    What if I keep the 7300 handy in a box and put it in when I have to use 10.4.11? ( select the start up disc, shut down, change the card, restart) Does the 5770 require a power cable to another board that I might damage with repeated changes?

  • My mac pro wont start. I push the power button and I get a click sound. A few seconds later another click sound and that it.

    My mac pro wont start. I push the power button and I get a click sound. A few seconds later another click sound and that it. I've tried different power plugs. Going direct into the wall, through a power strip. By iteslf, with other devices plugged in. I removed hard drives, and some RAM, and nothing. Sometimes it would not turn on, and then some minutes later it works. So its was sparatic, but now its been the same situation for three days where it wont turn on.
    I'm guessing power supply, but I wanted to see if anyone had a similar expereince and what the solution was, before I drag this beast to my local Apple store and have them look at it. Its a real pain to get it there and back and I want to be armed with some info for them. I already dragged this to them when it first started to do this, and of course it started up just fine for them. And you know if it works for the Genius then theres nothing wrong with. No matter what you explain to them.
    I figure if anyone had a the same problem and was able to resolve it, I can relate that experience to the Genius even if it start up for them.
    Thanks

    Try a SMC Reset using the extended method:
    Remove the AC power cord.
    Press the power-on button. [This drains the stored charge from the power supply]
    wait a quarter minute.
    Restore the power cord, being certain to JAM it into the socket, as the big block of rubber inhibits proper seating.
    wait a quarter minute
    attempt to power on.
    If no joy, examine the button battery half-hidden behind the graphics card. Remove it to measure the Voltage. A new battery should not cost over US$5, and measures a little over 3 Volts. BR-2032 is used in garage door opener controls and car door locks controls. The geeks at Radio Shack can measure it for you.

  • Hi - my 2011 Mac Pro no longer recognizes devices in the usb ports, I've been told it's the logic board.  is there a way I can connect the iomega external hard drive to it through the firewire or thunderbolt ports?

    Hi - my 2011 Mac Pro no longer recognizes devices in the usb ports, I've been told it's the logic board.  is there a way I can connect the iomega external hard drive to it through the firewire or thunderbolt ports?

    jrburrows wrote:
    Ok, fair enough.  But since Job's death - Apple's control on leaks has been terrible.  I got the new iPhone, and I like it - but it hasn't made nearly as big as an impression as previous ones.  Because of the vast ammount of leaks.  With the iPad mini leaks, it's 99% sure to come out next week.
    Apple uses many manufacturers and it's massive also websites prefer to report on Apple whether true or false because it brings more hits.
    Amd by "others" I meant other people on iPads - not other devices/manufacturers.  It's possible to do so, I just want to know how.  I honestly don't think we'll ever be in a Post-PC era until all tablets allow us to use USB in the way computers do.
    No, USB is not the future, you missed the memo about cloud and wireless computing?

  • I have a Mac pro(1 free bay) and a mac mini I need to back both of them  Is it better to use an external NAS HD or an internal hard drive on my mac pro (mid 2010) What option has the faster GB/s?

    I have a Mac pro(1 free bay) and a mac mini I need to back up both of them (time machine)  Is it better to use an external NAS HD or an internal hard drive on my mac pro (mid 2010)
    What option has the faster GB/s?

    Disk drive using native SATA bus interface will allow the drive to copy and always present and ready.
    But once you have backup any hourly changes should be smaller and as long as the NAS and your switch should allow enough.
    You should always have off line backups and don't rely on just one backup set or just TimeMachine.
    WD RED models are designed for RAID and NAS and 7.2k instead of your more standard slower green 5400 rpm green models while still costing less than WD Blacks.
    http://www.amazon.com/gp/product/B008JJLW4M/
    How to clone your system:
    http://macperformanceguide.com/Mac-HowToClone-backup.html
    http://macperformanceguide.com/Mac-HowToClone.html
    http://www.macupdate.com/app/mac/7032/carbon-copy-cloner
    Using Cloning as a Backup Strategy
    http://www.macupdate.com/app/mac/7032/carbon-copy-cloner
    http://www.bombich.com/software/updates/ccc-3.5.html
    Clone to internal, TimeMachine to NAS is one way to go at it.

  • I just installed OuickTime 7 Pro in my Mac Pro Ver 10.6.8. The video I am trying to view is codec h264 Compression dvcpro 50 hd. I have audio but no video. It says I need other software with QuickTime for it to work. Dose anyone know what I need?

    I just installed OuickTime 7 Pro in my Mac Pro Ver 10.6.8. The video I am trying to view is codec h264 Compression dvcpro 50 hd. I have audio but no video. It says I need other software with QuickTime for it to work. Dose anyone know what I need?

    I just installed OuickTime 7 Pro in my Mac Pro Ver 10.6.8. The video I am trying to view is codec h264 Compression dvcpro 50 hd. I have audio but no video. It says I need other software with QuickTime for it to work. Dose anyone know what I need?
    H.264 video should be supported by your basic Snow Leopard operating system. The DVCPRO HD family of codecs is part of the Apple "Pro" codecs package which is normally installed as part of a "Pro" video editing suite installer or contemporaneously installed separately as part of one of the newer pro editing apps like FCPX. if you already have one of these pro suites or apps installed or available, then re-install the correct codec package that is missing. If not, you will need to purchase a Pro suite or app to be able to install the required codec package.

  • Hey. I want to install windows 8 32bit on my mac pro (mid 2012). I upgraded the windows 7 I already had, but now I dont have drivers at all... I searched drivers for the windows 8 32 bit but couldn't find any... Any solutions guys?

    Hey everyone, 
    I want to install windows 8 32bit on my mac pro (mid 2012). I upgraded the windows 7 I already had, but now I dont have drivers at all...
    I searched drivers for the windows 8 32 bit but couldn't find any...
    Any solutions guys?
    Thanks a lot.
    Sincerely,
    Chiponn

    There's been an update for OSX ML which addresses the issue for installing Windows 8 on bootcamp.
    It's NOT recommended that you Upgrade.. However, the way to get the drivers is:
    You'll need an external USB drive formatted as FAT for this.
    1) In OSX, start the Bootcamp Assistant
    2) Press Next
    3) UNTICK 'Remove WIndows 7 or Later Version'
    4) TICK Download the Latest Windows Support Software from Apple
    5) Insert USB drive
    6) Press CONTINUE
    The drivers should download, and copy a WIndowsSupport folder onto the USB drive.
    I did notice that Windows 8 still requires beta drivers for some aspects such as VGA (the Radio HD Card), which you can get on the AMD website.
    Futhermore, why are you using Windows 8 "32" bit when you blatently have a powerful 64bit?
    Anyway, hope this post helps ;-)

  • Can this be done? Airport extreme connected wireless in extend mode to connect a wireless Mac Pro with an ethernet cable from the extended airport extreme..

    Can this be done? Airport extreme connected wireless in extend mode to connect a wireless Mac Pro with an ethernet cable from the extended airport extreme.

    This will work.....IF....you also have an Apple AirPort router configured to provide your wireless network.
    In other words, you need to have two Apple AirPort routers to extend a wireless network.
    When the AirPort Extreme is configured to "extend" the wireless of the "main" AirPort, it will provide more wireless coverage and the Ethernet ports are enabled, so you could connect your Mac Pro to any of the Ethernet ports and use that as a network and Internet connection.

  • MY MAC PRO MOUSE POINTER JUMPS FREELY AROUND THE SCREEN AND MAKES IT IMPOSSIBLE TO NAVIGATE PROGRAMS... ANY IDEAS

    My mac Pro mouse pointer jumps freely around the screen, making it dificult to navigate... it also moves the screen around without touching anything... any ideas whats wrong?

    Check this forum link for some good suggestions:
    https://discussions.apple.com/thread/4650109?tstart=0
    Post if you have any questions!

  • For some reason, the Flash Player on my MAC Pro stopped working, I've checked the install on my Adobe Flash Player and the are current, but the plug-ins don't seem to be working.  Can anyone help me get it working?

    For some reason, the Flash Player on my MAC Pro stopped working, I've checked the install on my Adobe Flash Player and the are current, but the plug-ins don't seem to be working.  Can anyone help me get it working?

    It happened w/ my MacPro 2.66 GHz Dual-Core Intel Xeon about 5 months ago; tried everything I could think of including multiple downloads of Flash, and hadn't seen any solutions here.  Adobe insisted many times that I download & update, but the newest vers. wouldn't work on the computer.
    On checking Adobe/Flash was reading the computer as being an earlier model. So the new version of Flash wouldn't work w/ it.  Snow Leopard 10.6.8 was being read correctly but not the computer model (can't remember what MP model  it was reading).
    Nothing worked. So -- a very old PC trick: If nothing else works get the hammer out and bludgeon it-- might work. So I reset everything by putting the Snow Leopard  install disk in, held down 'C' on restart and let it run. 
    Didn't take anything off the HDD first, just ran the install disk over everything.
    The experts on the forums are probably cringing right now & I'd like very much for them to jump in. Love to know how my computer model was being mis-read. All I can say is, for the brave and desparate, it worked for me. Something to keep in mind.
    It helped that I had a new computer on order & have 2 backups, one being mandatory. Might work only the one time but worth a check.
    Good luck on working this one out.

  • My mac pro is running really slow and the beach ball keeps appearing

    my mac pro is running really slow and the beach ball keeps appearing
    is there some good free software that cleans it up, new to macpro
    Software  OS X 10.9.2 (13C1021)

    Launch the Console application in any of the following ways:
    ☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
    ☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
    ☞ Open LaunchPad. Click Utilities, then Console in the icon grid.
    The title of the Console window should be All Messages. If it isn't, select
    SYSTEM LOG QUERIES ▹ All Messages
    from the log list on the left. If you don't see that list, select
    View ▹ Show Log List
    from the menu bar at the top of the screen.
    Click the Clear Display icon in the toolbar. Then try the action that you're having trouble with again. Select any messages that appear in the Console window. Copy them to the Clipboard by pressing the key combination command-C. Paste into a reply to this message by pressing command-V.
    ☞ The log contains a vast amount of information, almost all of which is irrelevant to solving any particular problem. When posting a log extract, be selective. A few dozen lines are almost always more than enough.
    Please don't indiscriminately dump thousands of lines from the log into this discussion.
    Please don't post screenshots of log messages—post the text.
    ☞ Some private information, such as your name, may appear in the log. Anonymize before posting.

  • I just got my first mac pro and I can't get the photos out of iPhotos moved on my hp external hard drive, I try export says unable, then I try to drag it from the desktop to the external hard drive but same problem. Thank you so much

    I just got my first mac pro and I can't get the photos out of iPhotos and move them on my hp external hard drive, I try export says unable, then I try to drag it from the desktop to the external hard drive but same problem. what to do? Thank you so much

    How is your external drive formatted? Use Disk Utility to check the volume format. If it is NTFS, you will need to reformat the HDD as exFAT in order to retain universal compatibility (RW to it on both Mac and Windows).

  • Chess.app runs OK on my MacBookPro under OS 10.6.8. Under the same OS on my Mac Pro Chess.app will not show the hint for the next move.

    Chess.app runs OK on my MacBookPro under OS 10.6.8. Under the same OS on my Mac Pro Chess.app will not show the hint for the next move. The detail on the desktop MacPro is 
    Model Name:    Mac Pro
      Model Identifier:    MacPro1,1
      Processor Name:    Dual-Core Intel Xeon
      Processor Speed:    2.66 GHz
      Number Of Processors:    2
      Total Number Of Cores:    4
      L2 Cache (per processor):    4 MB
      Memory:    1 GB
      Bus Speed:    1.33 GHz
      Boot ROM Version:    MP11.005C.B08
      SMC Version (system):    1.7f10
      Serial Number (system):    G87212BJUPZ
      Hardware UUID:    00000000-0000-1000-8000-0017F20A3C06

    Hello
    did the keaybord shortcut work ?
    For info chess app come from system install
    HTH
    Pierre

  • Wanted to know if the mac pro keyboards purchased in miami bring the letter "ñ"?

    wanted to know if the mac pro keyboards purchased in miami bring the letter "ñ"?

    ñ Ñ
    Type option-n, n
    Works on all US keyboards.
    é É
    option-e e
    Option-shift-?

  • I have Iphone 5 and mac pro, and i want to transfer pics through idrop. but my iphone not detect the mac pro. How i can turn the idrop on my computer?

    I have Iphone 5 and mac pro, and i want to transfer pics through idrop. but my iphone not detect the mac pro. How i can turn the idrop on my computer?

    The Mac Pro - the desktop computer - does not support Airdrop, if that's what you mean.
    Matt

Maybe you are looking for

  • Formatei meu PC, porém criei antes um Backup da minha área de usuário, existe maneira de recuperar os favoritos do Firefox??

    Re-instalei o Mozilla, porém verificando em meu backup da área de usuário, não encontrei arquivo que pudesse conter os favoritos. Também criei um backup da área de instalação do Mozilla, porém tampouco achei algo que pudesse me ajudar a recuperar os

  • Cannot Sign into Ovi Store and cannot create email...

    Hey all, I have just recently got my N8 back from Nokia. I sent it back due to numerous problems...battery life was less than 16hrs, kept saving sent messages, wouldn't update emails instantly and kept getting mail that was 4 days old, etc... But now

  • Problem with purchase order release strategy

    Hi Guru's     i am dealing with problem of  service purchase order release strategy , when i making the service  po ,  i am not giving any over fulfillment tolerance  ,  after release & making Service entry sheet of PO ,   when i go to the change mod

  • Problem in creating radiobutton dynamically

    Hi, In WdDoModifyView() of view, i wrote the following code...... IWDRadioButton button=(IWDRadioButton)view.createElement(IWDRadioButton.class,"radioButton1");          button.setText("abc");          IWDTransparentContainer tc=(IWDTransparentContai

  • Need Help Resizing in PS Elements 6

    I recently worked on a couple of my photos in PS Elements 6, and after I saved them, I found that they had changed size drastically.  Both were about 2MB originally, but after working on them one had gone down to a mere 190Kb, while the other had inc