Mac will only stay on when hooked up to charger - HELP

As of last week, my MAC just shut down randomly. Once I plugged the charger in, it would turn back on, but the second I take it out of the charger, it shuts off again. For the past week, I've kept the charger in place; however, I can tell it's eroding my battery. It used to be at 100% and now it's down to 95%. Has anyone experienced this issue? Better yet, does anyone know how to resolve this?

As SV mentioned, we'll need more details on your battery before we can give you a good direction to head in. Regarding your comment +*"I can tell it's eroding my battery. It used to be at 100% and now it's down to 95%"*+, if you are talking about the information in the top left of your display that shows your remaining charge, what you are seeing is normal. The charger charges your battery up to 100% and it will allow the battery to drop down to about 95% before it starts charging it up again. This is done basically so the battery doesn't need to recharge constantly every time it dips below 100%. However, this doesn't mean that you may not have a problem with your battery. We'll need the info that Steve asked for.

Similar Messages

  • I replaced battery and now will only turn on when plugged into a charger..

    I replaced my batter on my iphone 3gs and then it will only turn on when i connect it to a power source.
    After it has turned on you can take it off charge and it will stay on...
    Help please!! thanks

    Either you got a bad battery, didn't install it correctly, did some other damage while installing, or haven't let it charge enough yet. There's really nothing we can do to help you with any of those scenarios.
    Regards.

  • My 2008 macbook laptop will only stay on when plugged in. About 5 to 10 minutes after it has been unplugged it shuts down completly by itself.

    Does anybody out there have any advice for? and also my computer is becoming a bit slow, and i thought macs cannot get viruses so is there any way to make it go faster.? thank you whoever is nice enough to respond.

    Here it all is... Thank you very much.
    Battery Information:
      Model Information:
      Serial Number: DP-bq20z951-3976-16e4
      Manufacturer: DP
      Device name: bq20z951
      Pack Lot Code: 0000
      PCB Lot Code: 0000
      Firmware Version: 002a
      Hardware Revision: 0005
      Cell Revision: 0100
      Charge Information:
      Charge remaining (mAh): 3106
      Fully charged: Yes
      Charging: No
      Full charge capacity (mAh): 3106
      Health Information:
      Cycle count: 314
      Condition: Good
      Battery Installed: Yes
      Amperage (mA): -901
      Voltage (mV): 11877
    System Power Settings:
      AC Power:
      System Sleep Timer (Minutes): 60
      Disk Sleep Timer (Minutes): 10
      Display Sleep Timer (Minutes): 30
      Automatic Restart On Power Loss: No
      Wake On AC Change: No
      Wake On Clamshell Open: Yes
      Wake On LAN: Yes
      Display Sleep Uses Dim: Yes
      Battery Power:
      System Sleep Timer (Minutes): 10
      Disk Sleep Timer (Minutes): 10
      Display Sleep Timer (Minutes): 2
      Wake On AC Change: No
      Wake On Clamshell Open: Yes
      Display Sleep Uses Dim: Yes
      Reduce Brightness: Yes
    Hardware Configuration:
      UPS Installed: No
    AC Charger Information:
      Connected: Yes
      Charging: No

  • PowerMac G5 will ONLY boot up when the side panel is removed

    Hi,
    We have a PowerMac G5 Dual 2.5GHZ . This mac will ONLY boot up when the side panel and the clear plastic panel are removed. If the Mac is assembled, the Mac will start and Chime, but thats it. No display and the fans are dead quite. Any Suggestions? Thanks in advance

    Hi, I realised that this problem has ONLY occured AFTER I installed Leopard. I then reformated the hard drive and installed 10.34 ( the OS that came with the G5) and it is as good as gold. I then reformated the hard drive and installed Leopard. After a few minutes the G5 became noisy and unstable. I then reformatted the hard drive AGAIN and reinstalled 10.34 and it stable. How can I install Leopard without the machine behaving erratic? Thanks for any advice in advance

  • My iPhone 5 will not turn on. And when it does, it will only stay on for a short while and then it dies again.

    My iPhone 5 will not turn on. And when it does, it will only stay on for a short while and then it dies again.

    Hi lammyrock,
    I want to let you know to be patient as this troubleshooting can take some time depending on many different. First try putting your iPhone into recovery mode and then use iTunes to restore it. To do that, you can that by making sure that your iPhone is turned off, hold the Home button down while it is plugged into iTunes. You should get the graphic on your iPhone to plug it into iTunes and iTunes should prompt you to restore it. Once that is done and if you have a back up in iTunes or in iCloud, then you can put that back on after the restore is complete. Take a look at the article below for more information to help you. 
    If you can't update or restore your iPhone, iPad, or iPod touch
    http://support.apple.com/en-us/HT201263
    Hope this helps,
    -Norm G. 

  • HT201317 Once photostream pictures are downloaded onto my mac will they stay in iPhoto forever after i have deleted them off of my phone?

    Once photostream pictures are downloaded onto my mac will they stay in iPhoto forever after i have deleted them off of my phone?

    When I synced my iPhone I my Mac , it automatically created a file called photo stream and imported all photos from phone into that file on my Mac.
    Do you mean the "Photo Stream" album in the "Web" section of iPhoto? Like shown here?
    If that is the only place where you are seeing your photos, in "my Photo Stream" in the "Web" section of Photo, then you need to copy these photos to an event to import them into the library.
    The Photo Stream album is only showing you what currently can be imported from iCloud, and the photos will vanish after a month, so you are having a limited time to grab them.
    If you have enabled "Automatic Import" in iPhoto's Photo Stream Preferences, it should already have created an event "July Photo Stream" and other monthly events with the photos from the streams. What find in these monthly events has been savely imported.
    Regards
    Léonie

  • My ipod nano 6th gen will only turn on when plugged into a power source.

    My ipod nano 6th gen ONLY turns on when it is plugged into a power source. As soon as I unplug it, it turns off. I also tried to reset it and it did not help. Any suggestions? 

    Howdy mela1223,
    If I understand correctly your iPod will not stay on unless you have the charger plugged in even after resetting it. Normally this would indicate a hardware issue that would need a repair but to cover all the bases before that, the last troubleshooting that can be done for it would be to restore it with iTunes on a computer. 
    Restoring iPod to factory settings - Apple Support
    How to restore iPod
    Verify that you have an active Internet connection, because you may need to download new versions of the iTunes and iPod Software.
    Download and install the latest version of iTunes if necessary.
    Open iTunes. Connect your iPod to your computer using the USB or FireWire cable that came with your iPod.
    After a few moments, your iPod will appear in the Source panel in iTunes.
    Select your iPod in the Source panel. You will see information about your iPod appear in the Summary tab of the main iTunes window.
    Click Restore.
    If you are using a Mac, you will be asked to enter an administrator’s name and password.
    A progress bar will appear on the computer screen, indicating that stage one of the restore process has begun. When this stage is done, iTunes will present one of two messages with instructions specific to the iPod model you are restoring.
    Disconnect iPod and connect it to iPod Power Adapter (typically applies to older iPod models).
    Leave iPod connected to computer to complete restore (typically applies newer iPod models).
    During stage two of the restore process, the iPod displays an Apple logo as well as a progress bar at the bottom of the display. It is critical that the iPod remain connected to the computer or iPod power adapter during this stage. 
    Note: The progress bar may be difficult to see, because the backlight on the iPod display may be off.
    After stage two of the restore process is complete, the iTunes Setup Assistant window will appear. It will ask you to name your iPod and choose your syncing preferences, as it did when you connected your iPod for the first time.
    Thank you for using Apple Support Communities.
    Take care,
    Sterling

  • Ipad4 will only receive messages when it is switched on.

    Ipad4 will only receive messages when it is switched on. If messages are sent when it is switched off they never arrive. Any ideas on how to fix this please?

    The Mac uses a highly-parameterized display Driver, customized for the actual capabilities of the display. The settings are determined by a query to the display at power-on, when the Mac queries every attached display. The display name is also reported.
    System preferences > Displays > (Detect Displays) ...
    ... replicates the query to update what displays are present and their names and capabilities. So using that command when the display state is changed off to on or on to off should adjust the configuration to current state of things.

  • I am using an iPad and iPhone and have exchange as my email. Both will only collect mails when I am in the wifi of the office, and not when I am out and about. I can't seem to get a fix for it.

    I am using an iPad and iPhone and have exchange as my email. Both will only collect mails when I am in the wifi of the office, and not when I am out and about. I can't seem to get a fix for it.

    This - https://support.mozilla.org/en-US/kb/how-make-web-links-open-firefox-default - didn't work?

  • My mac will not show images when on the internet?

    My mac will not show images when on the internet?  I think I have inadvertently changed some settings but nor sure which one.

    I am going to assume you are using Safari here. If so then go to the Apple menu bar and hit Safari-> Preferences.  Under the Apperance tab there is a check box that is called "Display images when the page opens".  Check if that is unticked.

  • After updating my iphone 5s to IOS 8.0.2, I cant get internet on my 3g anymore. Can only get it when hooked to wifi. Tried restore, tried restart, fixed settings. Help?!?!?!?!?

    After updating my iphone 5s to IOS 8.0.2, I cant get internet on my 3g anymore. Can only get it when hooked to wifi. Tried restore, tried restart, fixed settings. Help?!?!?!?!?

    Hi diamondjill419,
    Here is an article that can help you troubleshoot this cellular data issue:
    iPhone: Troubleshooting a cellular data connection
    http://support.apple.com/kb/ts3780
    Thanks for being a part of the Apple Support Communities!
    Regards,
    Braden

  • I can start my iPod but it will only stay on the Apple icon screen for 5 minutes and then shuts off, what do I do to fix this problem?

    I can start my iPod but it will only stay on the Apple icon screen for 5 minutes and then shuts off, what do I do to fix this problem?

    Try:
    - iOS: Not responding or does not turn on
    - Also try DFU mode after try recovery mode
    How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
    - If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
    - If still not successful that indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
    Apple Retail Store - Genius Bar

  • Phone will only stay on while plugged in

    I have an iphone 4. It will only stay on while plugged in. While unplugged it shows nothing but a black screen.  It will not connect to wifi.  It won't even left me swipe the on/off switch.  Occassionaly it tells me that it is not connecting to the internet. (mostly on facebook but won't allow me on pintrest either).  Ideas?

    i would say try to restore as new and then replace it

  • PLEASE HELP when I upgraded to the new firefox my old one got deleted which had all my stuff and my mac is only 10.4.11 and wont work please help!!!

    PLEASE HELP when I upgraded to the new firefox my old one got deleted which had all my stuff and my mac is only 10.4.11 and wont work please help!!!

    Need to Resume download to complete the ongoing Process.
    Last Resort, put the iPhone in DFU mode (Google How to do that). Connect in iTunes. Follow on-screen prompts to Restore. All Data would be lost, if not backed up earlier.
    To save the photographs you may have to use third party software. Google is your friend.

  • My iPhone will not charge and will only turn on when plugged into adapter.

    I have tried to reset and nothing. It turns off if I unplug it and will only turn on when plugged in. The charge has not moved above 19% even though I let it charge for 3 hours while I was out. What do I do?

    http://support.apple.com/kb/TS2802

Maybe you are looking for

  • Switching to iphone.. then switching back to basic phone

    Ive had an LG enV for years.  Im thinking about getting an iphone.  Obviously I would need a data plan for my new iphone.  Lets say 3 months from now, I dont want to use the iphone and switch back to my basic LG phone.. Can i cancel my data plan i  h

  • Open a window in the same place EVERY time

    I have a TextEdit document in a password protected .dmg.  When I open the document, it opens in the middle of my screen, then I drag it out of the way to the far right side of the screen.  I'd like to be able to open it on the right side of my screen

  • In iTunes, I cannot drag and drop music into my Ipod.

    Correction: I can drag and drop a music file, but then on the iPod, the music file shows up in gray, unplayable, and just doesn't end up transferring. I have dragged and dropped music files on two different computers, now it doesn't work on either on

  • Idoc not fully posted

    Dear All, I am trying to download employees from HR to CRM system. Connection is already set up. When I process an Idoc in BD87 in CRM, system gives me a warning message that Object 01,CP,<pernr number> does not exist: infotype 5580 cannot be created

  • Can i use pci-7352 to run 4 or 6 axis (motors) if i am not using them same time

    can i use pci-7352 to run 4 or 6 axis (motors) if i am not using them same time. This is a stepper motor