Mac won't load after login after upgrading to mountain lion??
I installed Mountain Lion this morning. After restarting, it prompts me for my login information (as usual). However, nothing loads past this point. It keeps restarting. Any ideas?
I installed Mountain Lion this morning. After restarting, it prompts me for my login information (as usual). However, nothing loads past this point. It keeps restarting. Any ideas?
Similar Messages
-
Problem
High running Temperature
Specification
iMac 27 inch
Mac OS X Includes Software Snow Leopard upgraded to Mountain Lion OS X 10.8.03 (1278)
251 GB Flash Drive
2 TB Sata disk
Processor 3.4 Ghz Intel Core I7
Memory 16 GB 1333 MHz DDR3
Graphics AMD Radeon HD 6970 2048 MB
Video: Software Final Cut Pro X 10.0.8
I use the imac mainly for editing Video which when doing so it has reached temperatures of near to 60° C which causes the program to become unstable and needs to be cooled down to operate correctly.
An Apple technician (by phone) advised me to download an smcfancontrol. This allows each individual fan to increase speed and also advises the current temperature at °C. The smcfancontrol has been downloaded but this has not resolved the problem. By increasing the speed of the fan more heat is generated and creates additional noise.
I have since taken the iMac to an Apple Store for examination as suggested by APPLECARE when the fans were found to be working correctly. An Apple Store technician carried out a test, but not whilst working under the pressure of FINAL CUT PRO when the iMac generates a high temperature.
The Temperature Specification for this model is
Operating Temperature 20 °c to 35°C
Storage Temp.47°c
Clearly the temperature my iMac is operating at is excessive and could cause the computer to break down prematurely. Has anyone experienced this problem.
Frank HowellWhen was the last time you cleaned/vacuumed out all of your iMac's vents, slots and ports.
You need to do this with the iMac powered down, disconnected from power and everything disconnected.
Lay your iMac, screen down, on a soft surface, like a heavy towel. Use a small electronics vac, or portable or full size vac with hose and a crevice tool attachment and carefully and slowly vacuum every vent, slot and port on your iMac.
Then reconnect everything up, power up and download and install iStat Pro. Start working, then report the temps of your iMac after this has been done.
When using SMCFan Control, it is important not to run the fans at too high an RPM. This doesn't generate heat on its own, but will suck in more dust, lint and dirt into your iMac, and that will be the cause of additonal increases in heat.
I run my fans in the range of 1400-1600 RPMs. You can go as high as 1800 RPMs but it is important to keep the RPM range below either 1800 or below 2000 RPMs.
I, also, run a very small desktop fan pointed toward the upper back of my iMac to keep temps down even further. -
Are mac book pros mid 2010 capable of upgrading to mountain lion?
are mac book pros mid 2010 capable of upgrading to mountain lion?
Yes.
Upgrading from Snow Leopard to Lion or Mountain Lion
You can upgrade to Mountain Lion from Lion or directly from Snow Leopard. Mountain Lion can be downloaded from the Mac App Store for $19.99.
If you sign into the App Store and try to purchase Mountain Lion but the App Store says your computer is not compatible then you may still be able to upgrade to Lion per the following information.
A. Upgrading to Mountain Lion
To upgrade to Mountain Lion you must have Snow Leopard 10.6.8 or Lion installed. Purchase and download Mountain Lion from the App Store. Sign in using your Apple ID. Mountain Lion is $19.99 plus tax. The file is quite large, over 4 GBs, so allow some time to download. It would be preferable to use Ethernet because it is nearly four times faster than wireless.
OS X Mountain Lion - System Requirements
Macs that can be upgraded to OS X Mountain Lion
1. iMac (Mid 2007 or newer) - Model Identifier 7,1 or later
2. MacBook (Late 2008 Aluminum, or Early 2009 or newer) - Model Identifier 5,1 or later
3. MacBook Pro (Mid/Late 2007 or newer) - Model Identifier 3,1 or later
4. MacBook Air (Late 2008 or newer) - Model Identifier 2,1 or later
5. Mac mini (Early 2009 or newer) - Model Identifier 3,1 or later
6. Mac Pro (Early 2008 or newer) - Model Identifier 3,1 or later
7. Xserve (Early 2009) - Model Identifier 3,1 or later
To find the model identifier open System Profiler in the Utilities folder. It's displayed in the panel on the right.
Are my applications compatible?
See App Compatibility Table - RoaringApps.
For a complete How-To introduction from Apple see Upgrade to OS X Mountain Lion.
B. Upgrading to Lion
If your computer does not meet the requirements to install Mountain Lion, it may still meet the requirements to install Lion.
You can purchase Lion by contacting Customer Service: Contacting Apple for support and service - this includes international calling numbers. The cost is $19.99 (as it was before) plus tax. It's a download. You will get an email containing a redemption code that you then use at the Mac App Store to download Lion. Save a copy of that installer to your Downloads folder because the installer deletes itself at the end of the installation.
Lion System Requirements
1. Mac computer with an Intel Core 2 Duo, Core i3, Core i5, Core i7,
or Xeon processor
2. 2GB of memory
3. OS X v10.6.6 or later (v10.6.8 recommended)
4. 7GB of available space
5. Some features require an Apple ID; terms apply. -
Prior to upgrading to Mountain Lion, I never had to log back onto the Wifi signal in my home, but now I do. Anyone know the fix for this?
Hello,
Hi, this has worked for a few...
Make a New Location, Using network locations in Mac OS X ...
http://support.apple.com/kb/HT2712
10.7 & 10.8…
System Preferences>Network, top of window>Locations>Edit Locations, little plus icon, give it a name.
10.5.x/10.6.x/10.7.x instructions...
System Preferences>Network, click on the little gear at the bottom next to the + & - icons, (unlock lock first if locked), choose Set Service Order.
The interface that connects to the Internet should be dragged to the top of the list.
Instead of joining your Network from the list, click the WiFi icon at the top, and click join other network. Fill in everything as needed.
For 10.5/10.6, System Preferences>Network, unlock the lock if need be, highlight the Interface you use to connect to Internet, click on the advanced button, click on the DNS tab, click on the little plus icon, then add these numbers...
208.67.222.222
208.67.220.220
Click OK. -
How can I find out if my mac mini running snow leopard can be upgraded to mountain lion?
I have a mac mini with sufficient ram for the mountain lion OS however, I am unable to determine if the machine was created in early 2009. Is there a way to make sure my machine will take the upgrade without purchasing the operating system first?
Upgrade Paths to Snow Leopard, Lion, and/or Mountain Lion
You can upgrade to Mountain Lion from Lion or directly from Snow Leopard. Mountain Lion can be downloaded from the Mac App Store for $19.99. To access the App Store you must have Snow Leopard 10.6.6 or later installed.
Upgrading to Snow Leopard
You can purchase Snow Leopard through the Apple Store: Mac OS X 10.6 Snow Leopard — Apple Store (U.S.). The price is $19.99 plus tax. You will be sent physical media by mail after placing your order.
After you install Snow Leopard you will have to download and install the Mac OS X 10.6.8 Update Combo v1.1 to update Snow Leopard to 10.6.8 and give you access to the App Store. Access to the App Store enables you to download Mountain Lion if your computer meets the requirements.
Snow Leopard General Requirements
1. Mac computer with an Intel processor
2. 1GB of memory
3. 5GB of available disk space
4. DVD drive for installation
5. Some features require a compatible Internet service provider;
fees may apply.
6. Some features require Apple’s iCloud services; fees and
terms apply.
Upgrading to Lion
If your computer does not meet the requirements to install Mountain Lion, it may still meet the requirements to install Lion.
You can purchase Lion by contacting Customer Service: Contacting Apple for support and service — this includes international calling numbers. The cost is $19.99 (as it was before) plus tax. It's a download. You will get an email containing a redemption code that you then use at the Mac App Store to download Lion. Save a copy of that installer to your Downloads folder because the installer deletes itself at the end of the installation.
Lion System Requirements
1. Mac computer with an Intel Core 2 Duo, Core i3, Core i5, Core i7,
or Xeon processor
2. 2GB of memory
3. OS X v10.6.6 or later (v10.6.8 recommended)
4. 7GB of available space
5. Some features require an Apple ID; terms apply.
Upgrading to Mountain Lion
To upgrade to Mountain Lion you must have Snow Leopard 10.6.8 or Lion installed. Purchase and download Mountain Lion from the App Store. Sign in using your Apple ID. Mountain Lion is $19.99 plus tax. The file is quite large, over 4 GBs, so allow some time to download. It would be preferable to use Ethernet because it is nearly four times faster than wireless.
OS X Mountain Lion — System Requirements
Macs that can be upgraded to OS X Mountain Lion
1. iMac (Mid 2007 or newer) — Model Identifier 7,1 or later
2. MacBook (Late 2008 Aluminum, or Early 2009 or newer) —
Model Identifier 5,1 or later
3. MacBook Pro (Mid/Late 2007 or newer) — Model Identifier 3,1 or later
4. MacBook Air (Late 2008 or newer) — Model Identifier 2,1 or later
5. Mac mini (Early 2009 or newer) — Model Identifier 3,1 or later
6. Mac Pro (Early 2008 or newer) — Model Identifier 3,1 or later
7. Xserve (Early 2009) — Model Identifier 3,1 or later
To find the model identifier open System Profiler in the Utilities folder. It's displayed in the panel on the right.
Are my applications compatible?
See App Compatibility Table — RoaringApps.
For a complete How-To introduction from Apple see Upgrade to OS X Mountain Lion. -
Not able to browse my mac mini since my macbook pro is upgraded to mountain lion
I have a macmini (running Lion with all updates) and a macbook pro(with Mountain lion all updates) connected to my home network (wifi)
A few weeks ago I had macmini(Lion) and macbook pro had Snow leopard. I enabled file sharing between these two computers and
I could browse these computers from one another via Finder.
Since I upgraded macbook pro to Mountain lion, though I get the foreign computer icon in Finder, I can not browse one from another.
I click on the foreign computer icon, but nothing happens and it reports connection failed. Note there was no password change or
any other configuration change in between.
Have you seen this problem? Is this a bug introduced via Mountain Lion ? Anyone has any fix ?For who ever is struggling with this issue - following is helpful
https://discussions.apple.com/thread/3213194?start=0&tstart=0
http://www.macworld.com/article/1164672/bugs_and_fixes_solving_a_strange_file_sh aring_error.html -
(Self explanatory, I hope.)
That seems unusual unless you changed drives.
If you upgraded the drive it sees the computer as a different one to the original backup..
I am not sure that it isn't better to do a fresh backup but you can try and inherit the old backup..
See Pondini
B5 B6 http://pondini.org/TM/Troubleshooting.html -
Safari won't load some images (after upgrade to Mavericks from Lion)
Hi,
I've noticed that since I upgraded my OS from Lion to Mavericks, Safari won't load all images on certain websites.
I've tried loading the same pages on my daughter's MacBookPro (she upgraded from Mountain Lion to Mavericks) and everything works just fine.
We cross checked the Safari preferences and everything is identical.
Below are two pictures, the first one taken from my computer, the second one from my daughter's. As you can see, in the first photo the image won't display, while it's been perfectly loaded in the second photo.
Here's the website: http://blog.alice.tv/berengario/2013/11/16/trasmissione-su-arturo-tv/
I've tried opening the same page on Firefox, and all images are perfectly displayed.
Could you please help me?
Thank you for your support!
Kind regards,
LeoPlease read this whole message before doing anything.
This procedure is a diagnostic test. It’s unlikely to solve your problem. Don’t be disappointed when you find that nothing has changed after you complete it.
The purpose of the test is to determine whether the problem is caused by third-party software that loads automatically at startup or login, by a peripheral device, or by corruption of certain system caches.
Disconnect all wired peripherals except those needed for the test, and remove all aftermarket expansion cards. Boot in safe mode and log in to the account with the problem. Note: If FileVault is enabled on some models, or if a firmware password is set, or if the boot volume is a software RAID, you can’t do this. Ask for further instructions.
Safe mode is much slower to boot and run than normal, and some things won’t work at all, including sound output and Wi-Fi on certain models. The next normal boot may also be somewhat slow.
The login screen appears even if you usually log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin. Test while in safe mode. Same problem? After testing, reboot as usual (i.e., not in safe mode) and verify that you still have the problem. Post the results of the test. -
after upgrading to Mountain Lion my Mac Book pro takes 1min 15 to load
Apple made some changes to increase security that slowed the boot time.
Startup - Slow Boot
Startup - Slow Boot (2)
Startup - Slow Boot (3) -
Mac Mini won't sleep after upgrading to Mountain Lion
Upgraded to Mountain Lion (including the server upgrade) and now it won't sleep.
More info...
macmini:~ doug$ pmset -g
Active Profiles:
UPS Power -1
AC Power -1*
Currently in use:
hibernatemode 0
womp 1
networkoversleep 0
sleep 30 (sleep prevented by 1488)
powerbutton 0
ttyskeepawake 1
hibernatefile /var/vm/sleepimage
autorestart 0
disksleep 10
displaysleep 15
macmini:~ doug$ ps -ef |grep -e 1488
0 1488 1 0 9:20AM ?? 0:00.06 /Library/PrivilegedHelperTools/com.apple.serverd
What is PrivilegedHelperTools?
Also...
macmini:~ doug$ pmset -g assertions
11/14/12 9:35:32 AM PST
Assertion status system-wide:
PreventUserIdleDisplaySleep 0
PreventSystemSleep 1
PreventUserIdleSystemSleep 1
ExternalMedia 1
DisableLowPowerBatteryWarnings 0
UserIsActive 0
ApplePushServiceTask 0
BackgroundTask 0
Listed by owning process:
pid 1488(com.apple.serve): [0x0000000100000334] 00:15:27 PreventUserIdleSystemSleep named: "com.apple.server.filesharing"
pid 345(httpd): [0x00000008000001a7] 01:15:14 DenySystemSleep named: "com.apple.apache.denysystemsleep"
pid 24(powerd): [0x000000090000012c] 01:15:35 ExternalMedia named: "com.apple.powermanagement.externalmediamounted"
Kernel Assertions: 0x0012
* Kernel Assertion ID = 500
Created At = 12/31/69 4:03:47 PM PST
Modified At = 11/14/12 8:30:22 AM PST
Owner ID = 0xffffff801ec8b000
Level = 255
Assertions Set = None (4)
* Kernel Assertion ID = 501
Created At = 12/31/69 4:03:48 PM PST
Modified At = 11/14/12 8:29:48 AM PST
Owner ID = 0xffffff801ec93000
Level = 255
Assertions Set = None (4)
* Kernel Assertion ID = 502
Created At = 12/31/69 4:03:58 PM PST
Modified At = 11/14/12 8:35:35 AM PST
Owner ID = 0xffffff801ed05e00
Level = 0
Assertions Set = None (32)
* Kernel Assertion ID = 503
Created At = 11/14/12 8:21:23 AM PST
Modified At = 12/31/69 4:00:00 PM PST
Owner ID = 0xffffff801f9a4800
Level = 255
Assertions Set = None (8)
Any ideas how to solve?You can go into the OS X Server Forum and search for this issue. I think there are some discussiom threads that discuss it and you can read some of the solutions.
I'm also running Mountain Lion 10.8.2 and OS X Server on a Mac Mini and it won't sleep if I have the File Sharing, VPN and Printer Sharing services running. To me, this is a good thing as a server is usually available to client machines 24x7.
I did experiment and turned off each service one at a time to see which ones deny the sleep function and I found all 3 do.
Here's an example from my server. The bold entries are the culprits for my server.
server:~ server$ pmset -g assertions
11/14/12 10:58:07 AM MST
Assertion status system-wide:
PreventUserIdleDisplaySleep 1
CPUBoundAssertion 0
PreventSystemSleep 1
PreventUserIdleSystemSleep 1
ExternalMedia 1
DisableLowPowerBatteryWarnings 0
UserIsActive 1
ApplePushServiceTask 0
BackgroundTask 0
Listed by owning process:
pid 66(com.apple.serve): [0x000000010000012d] 02:24:31 PreventUserIdleSystemSleep named: "com.apple.server.filesharing"
pid 66(com.apple.serve): [0x000000010000012c] 02:24:31 PreventUserIdleSystemSleep named: "com.apple.ppp.l2tp"
pid 1683(ScreensharingAg): [0x0000000500000415] 00:00:23 NoDisplaySleepAssertion named: "screen sharing wake display"
pid 1683(ScreensharingAg): [0x0000000a00000414] 00:00:00 UserIsActive named: "screen sharing wake display"
Timeout will fire in: 179.9 Action=TimeoutActionRelease
pid 220(AppleFileServer): [0x0000000800000416] 00:00:16 DenySystemSleep named: "com.apple.AppleFileServer"
pid 20(powerd): [0x000000090000012e] 02:24:30 ExternalMedia named: "com.apple.powermanagement.externalmediamounted"
pid 1681(screensharingd): [0x0000000500000413] 00:00:23 NoDisplaySleepAssertion named: "screen sharing wake display"
pid 1681(screensharingd): [0x000000050000040f] 00:00:23 NoDisplaySleepAssertion named: "Nameless (via IOPMAssertionCreate)"
pid 1681(screensharingd): [0x0000000a00000412] 00:00:23 UserIsActive named: "screen sharing wake display"
Timeout will fire in: 156.8 Action=TimeoutActionRelease
pid 172(httpd): [0x0000000800000161] 02:24:32 DenySystemSleep named: "com.apple.apache.denysystemsleep" -
After upgrading to Mountain Lion on my 2011 27" iMac, my Mac occasionally lock-ups.
After upgrading to Mountain Lion on my 2011 27" iMac, my Mac occassionaly locks up while using Safari, Mail or Dreamweaver and I have to d a force-quit, then restart my Mac. Anybody having similar probelms?
I am thinking about doing a clean install of Mountain Lion. Would I be able to restore my applications and data from Time Machine after the re-install?My 24 inch iMac... 2.8 GHZ dual core (Early 2008) is having the same problem. After it sleeps, I go to use something... and the beachball of death occurs. This happens multiple times a day... and let me tell you... it is annoying... and I am the one who is being annoyed!
It could possibly be revolving around safari... as that is really the only thing that is running consistently. I don't use iTunes on this iMac as I have so many other Macs up and running in the house... and I never consume media on it... so I kind of dismiss iTunes being the culprit.
This is majorly affecting my Mac... in terms of reliability and uptime... which coincedently is the main reason why I switched to Mac in 2008. This is my only Mac that could upgrade to ML... so I don't know how widespread this is... but I hope that this problem can be solved...
I agree with another person who commented on this issue... do we really need a 10.8.1 update already... to fix this? -
After upgrading to Mountain Lion I am not able to access "security and privacy" button under "system preferences". I like to activate "find my mac" but cannot access privacy setting after upgrade. Kindly advice.
-
After upgrading to mountain lion my mac is very slow?
Hello
After upgrading to mountain lion my mac is very slow
It was starting in 10 seconds and shuting dow in 5 seconds and now it's taking more than one minute to start it or shut down it and everything is slow
why????????/
ThanksFirst, back up all data immediately, as your boot drive might be failing.
Take these steps when you notice the problem.
Step 1
Launch the Activity Monitor application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Activity Monitor in the icon grid.
Select the CPU tab of the Activity Monitor window.
Select All Processes from the menu in the toolbar, if not already selected.
Click the heading of the % CPU column in the process table to sort the entries by CPU usage. You may have to click it twice to get the highest value at the top. What is it, and what is the process? Also post the values for % User, % System, and % Idle at the bottom of the window.
Select the System Memory tab. What values are shown in the bottom part of the window for Page outs and Swap used?
Next, select the Disk Activity tab. Post the approximate values shown for Reads in/sec and Writes out/sec (not Reads in and Writes out.)
Step 2
You must be logged in as an administrator to carry out this step.
Launch the Console application in the same way as above. Make sure the title of the Console window is All Messages. If it isn't, select All Messages from the SYSTEM LOG QUERIES menu on the left.
Post the 50 or so most recent messages in the log — the text, please, not a screenshot.
When posting a log extract, be selective. Don't post more than is requested.
Please do not indiscriminately dump thousands of lines from the log into a message.
Important: Some personal information, such as your name, may appear in the log. Edit it out before posting. -
My computer cannot install a printer after I upgraded to Mountain Lion. I have downloaded the HP printer drivers from the Mac Store. I click on add printer on Print and scan, the printer is connected via USB. I get a message that the drivers on not on Mac Store and cannot be installed.
True, not part of the list.
An older printer? You can only try contacting HP. Note that Apple is only the "distributor" of these drivers; HP as the vendor develops them. Or not... -
After I upgraded to Mountain Lion, my Mac cannot access the data disk on the Time Capsule. Who else is having this problem and have you been able to solve it?
Bonjour PanicRev16
I use Grapher 2D 3D on my early 2006 iMac, but I tried it on my wife's Macbook Pro with Lion then Mountain Lion : no problem with Grapher 2.1 3D gcx files, Grapher 2.3 loves them !
You can try the 3D Grapher 2.1 files from the website http://y.barois.free.fr/grapher/ and see the result on your Mac Mountain Lion.
I updated Grapher documentation and bugs of this website on 15th december 2012 (Lion, then Mountain Lion).
Au revoir,
YB24 -
IPhoto Library won't open after upgrade to mountain lion
One of my iPhoto libraries (stored on a WD Pasport Studio) won't open properly after upgrade to Mountain Lion 4oo5 open ok. One opens but disc symbol keeps spinning and Iphoto stops responding. Any ideas?
See if anything in here will fix it:
1. Hold down the Command and Option keys as you click the iPhoto icon.
The Photo Library First Aid window opens:
Maybe you are looking for
-
HP color laserjet CP2025 will not print. Help.
I have a HP color laserjet CP2025, but it will not print. I installed the driver HP Color LaserJet CP2020 Series PCL 6. I have a Windows Vista Home Premium. There is a message to replace the cyan cartridge, but I assume if the printer has black ink,
-
Function to compare tow dates and set the value
Hi All, I have two dates with close date and Due date.And i want to set the value as 1 if close date is less then or equal to to due date else 0 .And my other condition is to set 1 when close date is greater the due date.Can any one help me how can
-
Failed to allocate port(s) in the specified range(s) for the following....
Hi, I'm attempting to install oracle 10.2.0 on Solaris 10. When I create a database i get the error: Failed to allocate port(s) in the specified range(s) for the following process(es): ..... So I look at the logs and there looks like to be some confi
-
Good Morning, I know i can use Command IF...ENDIF in SAPscript. As far as i know SELECT...ENDSELECT and LOOP...ENDLOOP aren't allowed. Is this correct? Best Regards, Pedro Gaspar
-
The advice from Barbara B. did not work as the only thing running in task manager was the update . Once this reaches 13% (Camera Raw 8.3...) it asks for the application ElementsAutoAnalizer.exe to be closed to continue. How can this be done?