MacBook Air can't see my bluetooth headphones

PXC 310 Sennheiser not visible for MacBook Air 2 (though it works fine with my cellphone). Tried enabling AptX Codec in Bluetooth Explorer and deleting other devices as advised https://discussions.apple.com/thread/3891328?start=0&tstart=0 . Anybody has any better ideas? Thanks!

Nobody answered me, I discovered a way to do it by myself.
Specify the device and hold the finger on the headphones.

Similar Messages

  • Macbook air can't see time machine?

    macbook air can't see time machine?

    Can it see the external drive? Look at Section B
    Time Machine Troubleshooting

  • Why my macbook air can't see the airplay icon from the top right

    why my macbook air can't see the airplay icon from the top right

    and how to connect to airplay, please help, not see any icon

  • My macbook Pro doesn't see my bluetooth headphones

    Hi, I got a new macbook pro and I am using Sony DR-BT21G headphones, these are bluetooth indeed. The problem is that my macbook does not see my headphones when I am trying to set it on my Mac. The headphone does not work more if I enter the IP of my headphone manually.
    I hope you guys will be able to help me.

    Nobody answered me, I discovered a way to do it by myself.
    Specify the device and hold the finger on the headphones.

  • My MacBook Air can't see 5 Ghz "N" signal?

    Any reason for this? My iMac can see it.
    I've also posted in another forum that while connecting to my AEBS via the 2.4 Ghz signal, my MBA is not achieving download speeds nearly comparable to my desktop iMac (connecting my iMac wirelessly to the AEBS).
    The networking settings are the same for both machines, but my MBA is slogging with download speeds, which are reporting to be slower (by a factor of 2x) than my upload speeds (my iMac speeds are much faster and near parity on the up-and down-load rates).
    I'm connecting to the internet via Comcast 50 service, which is connecting to a Linksys WRT610n router. The AEBS is connected via ethernet.
    Any thoughts??

    Welcome to the discussions!
    A few thoughts...
    The higher frequency 5 GHz signals are absorbed by walls and any obstructions much more quickly than 2.4 GHz signals, so that may be a contributing factor in the question about not being able to "see" the 5 GHz signal.
    If the MBA and iMac are in similar locations, the information in your post indicates that the wireless card in your MBA may not be performing up to par. This may or may not be related to the 5 GHz problem.
    I assume you've done the standard things like restarting the router, your computer, deleting your computer wireless connection and password in Keychain Access and then establishing another connection, correct?

  • MacBook Air does not See a Plantronics Voyager Pro bluetooth headset

    My MacBook Air does not "see" my Plantronics Voyager Pro + bluetooth headset as a discoverable bluetooth asset.  I have read on Apple and Plantronics forums that these two devices should be compatible, but so far no luck.  Anybody have any experience with this situation?

    Turns out the Voyager Pro Bluetooth headset failed...exchanging it for a new one and should be GTG.  Thanks.

  • My MacBook Air can't get past the gray screen with the apple logo. What's the fix?

    My MacBook Air can't get past the gray screen with the Apple logo, so I can't login. Does anyone know the fix for this?

    Take each of these steps that you haven't already tried. Stop when the problem is resolved.
    Step 1
    The first step in dealing with a boot failure is to secure your data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since your last backup, you can skip this step.
    There are several ways to back up a Mac that is unable to boot. You need an external hard drive to hold the backup data.
    a. Boot into Recovery by holding down the key combination command-R at the startup chime, or from a local Time Machine backup volume (option key at startup.) Release the keys when you see a gray screen with a spinning dial. When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in the support article linked below, under “Instructions for backing up to an external hard disk via Disk Utility.”
    How to back up and restore your files
    b. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, boot the non-working Mac in target disk mode by holding down the key combination command-T at the startup chime. Connect the two Macs with a FireWire or Thunderbolt cable. The internal drive of the machine running in target mode will mount as an external drive on the other machine. Copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
    How to use and troubleshoot FireWire target disk mode
    c. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
    Step 2
    Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to boot, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can boot now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
    Before reconnecting an external storage device, make sure that your internal boot volume is selected in the Startup Disk pane of System Preferences.
    Step 3
    Boot in safe mode.* The instructions provided by Apple are as follows:
    Shut down your computer, wait 30 seconds, and then hold down the shift key while pressing the power button.
    When you see the gray Apple logo, release the shift key.
    If you are prompted to log in, type your password, and then hold down the shift key again as you click Log in.
    Safe mode is much slower to boot and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
    The login screen appears even if you usually log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
    *Note: If FileVault is enabled, or if a firmware password is set, or if the boot volume is a software RAID, you can’t boot in safe mode. Post for further instructions.
    When you boot in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, your boot volume is damaged and the drive is probably malfunctioning. In that case, go to step 5.
    If you can boot and log in now, reboot as usual (i.e., not in safe mode.) If the boot process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
    Step 4
    Sometimes a boot failure can be resolved by resetting the NVRAM.
    Step 5
    Launch Disk Utility in Recovery mode (see above for instructions.) Select your startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
    This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it produces. Look for the line "Permissions repaired successfully" at the end of the output. Then reboot as usual.
    Step 6
    Boot into Recovery again. When the OS X Utilities screen appears, follow the prompts to reinstall the OS. If your Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
    Note: You need an always-on Ethernet or Wi-Fi connection to the Internet to use Recovery. It won’t work with USB or PPPoE modems, or with proxy servers, or with networks that require a certificate for authentication.
    Step 7
    Repeat step 6, but this time erase the boot volume in Disk Utility before installing. The system should automatically reboot into the Setup Assistant. Follow the prompts to transfer your data from a backup.
    Step 8
    If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store to have the machine tested.

  • Can I use a Bluetooth headphone/microphone for capture sound instead of normal iPhone mic when shooting video?

    Can I use a Bluetooth headphone/microphone for capture sound instead of normal iPhone mic when shooting video?
    The sound when I record video is not so good, so I'm trying to use the Bluetooth headphone/microphone to capture a person voice but not know which setting to use.

    Hi Robert
    Thanks for answering. I didn't know where to post other than the bluetooth forum which is relatively quiet and had no answers forthcoming.
    Yes the voice isn't reaching the amp although it is registering on the input bar in the Sound System Prefs, just won't "play through" as it were. I can't see how it could be done I was just hoping someone might see something I am missing.
    It seems a shame that you can't do it as iTunes on an old iBook makes a good juke box for DJ'ing and with everything becoming wireless these days it seems sensible that you could cut that one last wire.
    Mike

  • MacBook Air can't connect to IPhone 5?

    Am I missing something or can the MacBook Air really not connect over bluetooth to the IPhone 5? I have paired the devices, but right when I do and then try to connect them, The connection fails on my phone because "'My MacBook Air' is not supported -->forget this device" and it fils on my computer because the "Network is unuavabiale". Please Help!!

    iOS: Use AirPlay to wirelessly stream content

  • HT4628 My MacBook Air does not see my wireless network

    My iPhone and iPad Mini see the network and connect with no problem. However the MacBook Air doesn't see the network. I tried adding it manually and it still does not recognize the network. Any ideas what I can do to resolve this issue?

    I am having the same problem and it is still not coming up supposed to be plug and play and Mac friendly?
    Slim Portable USB 2.0 External CD-RW/DVD Combo Drive

  • My Macbook Air can delete files and folders and take them to Trash Can but cannot delete from Trash Can . Cannot empty trash securely.

    My Macbook Air can delete files and folders and take them to Trash Can but cannot delete from Trash Can . Cannot empty trash securely.

    Launch the Console application in any of the following ways:
    ☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
    ☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
    ☞ Open LaunchPad. Click Utilities, then Console in the icon grid.
    Make sure the title of the Console window is All Messages. If it isn't, select All Messages from the SYSTEM LOG QUERIES menu on the left. If you don't see that menu, select
    View ▹ Show Log List
    from the menu bar.
    Click the Clear Display icon in the toolbar. Then try the action that you're having trouble with again. Select any messages that appear in the Console window. Copy them to the Clipboard by pressing the key combination command-C. Paste into a reply to this message by pressing command-V.
    When posting a log extract, be selective. In most cases, a few dozen lines are more than enough.
    Please do not indiscriminately dump thousands of lines from the log into this discussion.
    Important: Some private information, such as your name, may appear in the log. Anonymize before posting.

  • I lost App store app on my macbook air.can i get it now?

    i lost App store app on my macbook air.can i get it now?

    Are you running with Snow Leopard 10.6.5 as your profile suggests.   If so you should not be able to get to the App Store.   So what do you have?
    You need Snow Leopard update 10.6.8.   Mac OS X 10.6.8 Update Combo v1.1
    Once you have that I don't see why not.   Check your purchase listing.   If it is there you can download again free.

  • Macbook air can't go to the internet when connected with hard disk

    Hi, so my macbook air can't go to the internet everytime when it is connected with my hard disk. The wifi icon on the top right corner says my macbook is connected to my wifi but my macbook just can't go to the internet. I unplugged my hard disk and I have no problem connecting to the internet right away? I would like to know if there is any solution for this problem.
    Thank you

    Try resetting your SMC.
    Resetting the SMC of an Intel-based portable Mac with a battery you should not remove on your own
    Note: This will not delete any data.
    The SMC is responsible for controlling various system functions. None of your data will be deleted by resetting the SMC.
    Shut down the computer by going to Apple () > Shut Down…
    Select Shut Down or allow the computer to shut down automatically.
    Plug in the MagSafe power adapter into a power source and then connect it to your Mac if you have not already done so.
    On the built-in keyboard, press the (left side) Shift (⇧), Control (⌃), and Option (⌥) keys and the Power Button at the same time.
    Release the (left side) Shift (⇧), Control (⌃), and Option (⌥) keys and the Power Button at the same time.
    I hope I helped.
    Austin

  • HT4260 I did everything the article suggests. And for my macbook pro it works perfectly. But all the other devices (iphone 5, 4, Macbook Air) can't connect to the network. Anybody any idea's?

    I did everything the article suggests. And for my macbook pro it works perfectly. But all the other devices (iphone 5, 4, Macbook Air) can't connect to the network. Anybody any idea's?

    Try resetting your modem. Power it down. Wait a moment, then power it up again. While it resets, do not change what is connected to it.
    In another, though unrelated article, Apple recommends the following:
    If you have configured your Wi-Fi base stations in the past, it may be helpful to do a factory default reset of each Wi-Fi base station that will be part of the wireless extended network before you begin.
    This step really ought not be considered optional for the configuration you propose. If the problem persists after resetting your modem, reset everything else too.

  • MacBook Air can't connect to WiFi; iPhone, iPad can

    I'm a pretty experienced Mac and WiFi user, but this one has me stumped.
    I was recently waiting for my car to be serviced and tried to connect to the dealer's free WiFi network (Sonic via ATT broadband).  My iPhone 4s and my iPad3 had no problem signing-in to Sonic (OK'ing the terms) and accessing the internet, but I could not connect using my MacBook Air (model 4.2). I tried a number of things (e.g., refreshing the DHCP address, turning wifi off/on, etc.) - none worked.
    The person at the dealership said, "Macs seem to have a probelm connecting."
    FWIW, I have no problem connecting to my home, my work, and other WiFi networks on any of these devices.
    Any ideas about why my iPhone and iPad can connect to the Sonic WiFi and my MacBook Air can't?

    Hi Anh Tu BUI,
    Thanks for using Apple Support Communities.  This article has information on troubleshooting Wi-Fi issues for your MacBook Air:
    Wi-Fi: How to troubleshoot Wi-Fi connectivity
    http://support.apple.com/kb/HT4628
    Cheers,
    - Ari

Maybe you are looking for