Macbook Air internet fails 50% of the time.
I'm a first time mac owner and currently very dissatisfied. I've had my MBA for about 3 months now, its running 10.7.4 Lion and it was running fine for a long while. recently I have been having issues where I launch safari and the system hangs, the page either doesn't load or takes 20-30 minutes to load. It takes days for my email to sync/download. the system is nearly unsuable.
What I have done to try and make it work:
- bought a wifi repeater to extend signal range/strength
- boosted both router and repeater with 14-20Db antenne
- run dead run wired connection through my house and use ethernet USB adapter
- On the computer, turned wifi on and off, The issues is persistant with wired connection too.
- Turn off bluetooth and remove bluetooth devices
- ensure connection in network manager, I have connection via both wifi and eithernet, both DHCP's are verified and they work perfectly over the internal network.
I know the external network is not an issue, I have 3 Win7 machines, 4 android devices, an ipod touch, and 2 Ubuntu servers connected. Professonally I'm a network administrator , I know my house is wired correctly and recieving proper signal.
Additionally will this problem be solved if I upgrade to Mountain Lion? I upgraded the system very early on. That is about the time the problems started. The wifi issues were bad enough to make me revert back to 10.7.4.
I've been beating my head aginst a wall for 3 months. Really dissatisfied that I have a 1000 dollar system that only works 50% of the time.
~Casey
Connect via Ethernet and turn Wi-Fi off. Boot into Recovery by holding down the key combination command-R at the startup chime. Release the keys when you see a gray screen with a spinning dial.
From the OS X Utilities screen, select Get Help Online. A clean copy of Safari will launch. No plugins, such as Flash, will be available. While in Recovery, you'll have no access to your saved bookmarks or passwords, so make a note of those before you begin, if they're needed for the test.
Test. After testing, reboot as usual and post the results.
Similar Messages
-
I just got a new MacBook Air -- Moving data over from the Time Capsule over WiFi??
I just bought a new MacBook Air because my MacBook Pro 2008 died completely. I own a Time Capsule and it backed up regularly. I'd like to just move over all my data to my new 256GB MacBook Air, but it doesn't seem to be recognizing the Time Capsule over WiFi? I had the Time Capsule set to backup over Ethernet. Does this mean I can only access my files vs. Ethernet? Does that mean I need a USB to Ethernet adapter?
Backing up other Ethernet doesn't prevent access via Wi-Fi.
If the Time Capsule creating a wireless network? If not, you'll need to configure it to do so in order to allow the MBA to connect to it. If it does, can you connect the MBA to the Time Capsule's network?
Depending on the amount of data you want to transfer, using a USB-to-Ethernet adapter would help things run faster. -
Macbook air can't go to the internet when connected with hard disk
Hi, so my macbook air can't go to the internet everytime when it is connected with my hard disk. The wifi icon on the top right corner says my macbook is connected to my wifi but my macbook just can't go to the internet. I unplugged my hard disk and I have no problem connecting to the internet right away? I would like to know if there is any solution for this problem.
Thank youTry resetting your SMC.
Resetting the SMC of an Intel-based portable Mac with a battery you should not remove on your own
Note: This will not delete any data.
The SMC is responsible for controlling various system functions. None of your data will be deleted by resetting the SMC.
Shut down the computer by going to Apple () > Shut Down…
Select Shut Down or allow the computer to shut down automatically.
Plug in the MagSafe power adapter into a power source and then connect it to your Mac if you have not already done so.
On the built-in keyboard, press the (left side) Shift (⇧), Control (⌃), and Option (⌥) keys and the Power Button at the same time.
Release the (left side) Shift (⇧), Control (⌃), and Option (⌥) keys and the Power Button at the same time.
I hope I helped.
Austin -
My MacBook Air is very slow. Every time I click the mouse, the spinning wheel appears and remains for up to 30 seconds before the screen changes. This has been happening the past 24 hours. Any ideas?
First, back up all data immediately, as your boot drive may be failing.
If you have more than ten or so files or folders on your Desktop, move them, temporarily at least, somewhere else in your home folder.
If iCloud is enabled, disable it.
Disconnect all wired peripherals except keyboard, mouse, and monitor, if applicable. Launch the usual set of applications you use when you notice the problem.
Step 1
Launch the Activity Monitor application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ If you’re running Mac OS X 10.7 or later, open LaunchPad. Click Utilities, then Activity Monitor in the page that opens.
Select the CPU tab of the Activity Monitor window.
Select All Processes from the menu in the toolbar, if not already selected.
Click the heading of the % CPU column in the process table to sort the entries by CPU usage. You may have to click it twice to get the highest value at the top. What is it, and what is the process? Also post the values for % User, % System, and % Idle at the bottom of the window.
Select the System Memory tab. What values are shown in the bottom part of the window for Page outs and Swap used?
Step 2
You must be logged in as an administrator to carry out this step.
Launch the Console application in the same way as above. Make sure the title of the Console window is All Messages. If it isn't, select All Messages from the SYSTEM LOG QUERIES menu on the left.
Post the 50 or so most recent messages in the log — the text, please, not a screenshot.
Important: Some personal information, such as your name, may appear in the log. Edit it out before posting. -
I am having problems opening videos on my MacBook Air. I keep receiving the message to download Adobe flash player. I have gone to the site an downloaded it several times. It shows it is actually downloading, but still receive the message.
Hi..
Assuming you are using Safari ...
Quit Safari.
Open System Preferences > Flash Player then select the Storage tab. Click: Delete All
Now uninstall the Flash plugin then reinstall new > Troubleshoot Flash Player | Mac OS
Make sure to uninstall the currently installed Flash plugin first.
Launch Safari From your Safari menu bar click Safari > Empty Cache
Now try a video.
BTW... if you have the ClickToFlash extension installed, that can prevent Flash based video from streaming. It can also be installed as a plugin in /Library/Internet-Plug-Ins.
And check to see if Safari is running in 32 bit mode. Right or control click the Safari icon in your Applications folder then click Get Info. If the box next to: Open in 32 bit mode is selected, deselect, quit then relaunch Safari. -
My macbook air will not connect to the internet due to a self assigned IP address. I have tried trawling the support forums for hours, but either I can't understand the suggestions, or they don't work. Please explain to me in simplest terms how I can fix this. Many thanks!
The warranty entitles you to complimentary phone support for the first 90 days of ownership.
If you bought the product in the U.S. directly from Apple (not from a reseller), you have 14 days from the date of delivery in which to exchange or return it for a refund. In other countries, the return policy may be different. If you bought from a reseller, its return policy applies. -
Macbook Air will not connect to the internet via Wi-Fi or Ethernet
Macbook Air will not connect to the internet via Wi-Fi or Ethernet? Any ideas why not and how to fix this problem?
Power down the router. Unplug the cord from the wall. Wait a while.
Plug the cord back in. Restart the router.
Wait until all the lights are lit up properly.
Restart the computer.
Best. -
Can i trust a mail from apple.dk@voila.fr. I vun a MacBook air in a competision on the Internet?
I vun a MacBook air in a competision on the Internet?
Probably not. Computers are not given away to just anyone out of the blue. Sounds phishy to me. Reminds me of the Nigerian wanting to give you a boatload of money.
Did you enter the compitition from some place you know? If not don't trust it
Do you know who is at that email address? If no then don't trust it
Is the email asking for personal information? If yes don't trust it
Is there a link in the email linking to some other third party? If yes, don't trust it -
My MacBook Air constantly freezes when surfing the Internet and I keep having to restart or shutdown the computer. Any advice on what could be wrong?
My MacBook Air constantly freezes when surfing the Internet and I keep having to restart or shutdown the computer. Any advice on what could be wrong?
-
How do i log in on a macbook air with out wifi for the first time
How do i log in on a macbook air with out wifi for the first time
More details needed.
Otherwise just startup the computer and enter your password.
New Mac?
A new Mac comes with 90 days of free tech support from AppleCare.
AppleCare: 1-800-275-2273
Call AppleCare.
Best. -
my macbook air won't get past the white apple screen. I've tried power cycling the batter but won't help
Take each of these steps that you haven't already tried. Stop when the problem is resolved.
Step 1
The first step in dealing with a startup failure is to secure the data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since the last backup, you can skip this step.
There are several ways to back up a Mac that is unable to start. You need an external hard drive to hold the backup data.
a. Start up from the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.” The article refers to starting up from a DVD, but the procedure in Recovery mode is the same. You don't need a DVD if you're running OS X 10.7 or later.
b. If Step 1a fails because of disk errors, and no other Mac is available, then you may be able to salvage some of your files by copying them in the Finder. If you already have an external drive with OS X installed, start up from it. Otherwise, if you have Internet access, follow the instructions on this page to prepare the external drive and install OS X on it. You'll use the Recovery installer, rather than downloading it from the App Store.
c. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, start the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
d. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
If the startup process stops at a blank gray screen with no Apple logo or spinning "daisy wheel," then the startup volume may be full. If you had previously seen warnings of low disk space, this is almost certainly the case. You might be able to start up in safe mode even though you can't start up normally. Otherwise, start up from an external drive, or else use the technique in Step 1b, 1c, or 1d to mount the internal drive and delete some files. According to Apple documentation, you need at least 9 GB of available space on the startup volume (as shown in the Finder Info window) for normal operation.
Step 3
Sometimes a startup failure can be resolved by resetting the NVRAM.
Step 4
If you use a wireless keyboard, trackpad, or mouse, replace or recharge the batteries. The battery level shown in the Bluetooth menu item may not be accurate.
Step 5
If there's a built-in optical drive, a disc may be stuck in it. Follow these instructions to eject it.
Step 6
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to start up, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can start up now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
Step 7
If you've started from an external storage device, make sure that the internal startup volume is selected in the Startup Disk pane of System Preferences.
Start up in safe mode. Note: If FileVault is enabled, or if a firmware password is set, or if the startup volume is a software RAID, you can’t do this. Post for further instructions.
Safe mode is much slower to start and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know the login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
When you start up in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, the startup volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 11. If you ever have another problem with the drive, replace it immediately.
If you can start and log in in safe mode, empty the Trash, and then open the Finder Info window on the startup volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then restart as usual (i.e., not in safe mode.)
If the startup process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 8
Launch Disk Utility in Recovery mode (see Step 1.) Select the startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then restart as usual.
Step 9
If the startup device is an aftermarket SSD, it may need a firmware update and/or a forced "garbage collection." Instructions for doing this with a Crucial-branded SSD were posted here. Some of those instructions may apply to other brands of SSD, but you should check with the vendor's tech support.
Step 10
Reinstall the OS. If the Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Step 11
Do as in Step 9, but this time erase the startup volume in Disk Utility before installing. The system should automatically restart into the Setup Assistant. Follow the prompts to transfer the data from a Time Machine or other backup.
Step 12
This step applies only to models that have a logic-board ("PRAM") battery: all Mac Pro's and some others (not current models.) Both desktop and portable Macs used to have such a battery. The logic-board battery, if there is one, is separate from the main battery of a portable. A dead logic-board battery can cause a startup failure. Typically the failure will be preceded by loss of the settings for the startup disk and system clock. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
Step 13
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store, or go to another authorized service provider. -
My MacBook Air can't get past the gray screen with the apple logo. What's the fix?
My MacBook Air can't get past the gray screen with the Apple logo, so I can't login. Does anyone know the fix for this?
Take each of these steps that you haven't already tried. Stop when the problem is resolved.
Step 1
The first step in dealing with a boot failure is to secure your data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since your last backup, you can skip this step.
There are several ways to back up a Mac that is unable to boot. You need an external hard drive to hold the backup data.
a. Boot into Recovery by holding down the key combination command-R at the startup chime, or from a local Time Machine backup volume (option key at startup.) Release the keys when you see a gray screen with a spinning dial. When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in the support article linked below, under “Instructions for backing up to an external hard disk via Disk Utility.”
How to back up and restore your files
b. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, boot the non-working Mac in target disk mode by holding down the key combination command-T at the startup chime. Connect the two Macs with a FireWire or Thunderbolt cable. The internal drive of the machine running in target mode will mount as an external drive on the other machine. Copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
How to use and troubleshoot FireWire target disk mode
c. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to boot, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can boot now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
Before reconnecting an external storage device, make sure that your internal boot volume is selected in the Startup Disk pane of System Preferences.
Step 3
Boot in safe mode.* The instructions provided by Apple are as follows:
Shut down your computer, wait 30 seconds, and then hold down the shift key while pressing the power button.
When you see the gray Apple logo, release the shift key.
If you are prompted to log in, type your password, and then hold down the shift key again as you click Log in.
Safe mode is much slower to boot and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
*Note: If FileVault is enabled, or if a firmware password is set, or if the boot volume is a software RAID, you can’t boot in safe mode. Post for further instructions.
When you boot in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, your boot volume is damaged and the drive is probably malfunctioning. In that case, go to step 5.
If you can boot and log in now, reboot as usual (i.e., not in safe mode.) If the boot process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 4
Sometimes a boot failure can be resolved by resetting the NVRAM.
Step 5
Launch Disk Utility in Recovery mode (see above for instructions.) Select your startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it produces. Look for the line "Permissions repaired successfully" at the end of the output. Then reboot as usual.
Step 6
Boot into Recovery again. When the OS X Utilities screen appears, follow the prompts to reinstall the OS. If your Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Note: You need an always-on Ethernet or Wi-Fi connection to the Internet to use Recovery. It won’t work with USB or PPPoE modems, or with proxy servers, or with networks that require a certificate for authentication.
Step 7
Repeat step 6, but this time erase the boot volume in Disk Utility before installing. The system should automatically reboot into the Setup Assistant. Follow the prompts to transfer your data from a backup.
Step 8
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store to have the machine tested. -
So our school lets us use Macbook Airs for the school year, and it has facetime on it. I know facetime isn't blocked because like everyone else is using it. So I decide to give it a try. I click the icon, it says enter your apple ID. I dont have one, so I click to make one, and do so. I then enter my apple ID and click next. The screen reads "People will call you using your email address. What email address would you like to use?" I enter my email address in the box below the message, and then go to my email and click the link, and sign in, thus verifying the email. I go back to the facetime window, and click next. At the top it says Verified, but when I click next it doesn't go on to the next step, it simply blacks out the next button so that I can not click it, and after a few minutes a message comes up that says "Could not verify the email address. Please check your network connection and try again."
So that is the issue, please help!!!!!
*Note-I repeat that I know it is not blocked by the school because everyone else uses it just fine.*Hello BassoonPlayer,
Since you are using one of the the school's Macbooks, it is quite possible that the time and date are not properly set on the computer that you are using. FaceTime will not work if you do not have the proper time zone set up for the location that you are in. This past week, there were a two other Macbook users I've helped by simply telling them to set the Date/Time properly. By the way, you described your problem very well, which makes it easier for us to help you. Hope this solves your problem -- if not, post back and I can suggest other remedies.
Wuz -
I live in the US and want to buy a MacBook Air with norwegian keyboard in the Apple Store. Is that possible?
In earlier years you can go th an Apple Store, buy a Macbook Pro and ask for a replacement to a other type of keyboard. I do this 2-3 times in the last years for german keyboards. If you done this on the same day you bought the macbook, the replacement happened without charge anything. It was a great service.
Yesterday i go back to the same store like before and both - the sales representative and the guys an the GeniusBar told me - that this is not offered by Apple anymore. Because the US Apple Online Store do not offer other Keyboards the US-based keyboards and the German Apple Online Store do not deliver to other countries the final conglusion from the Apple Stuff was:
Flight to germany, but it over their.
I see here in the Support community a lot of questions about norwegian, german and other kind of keyboards they want to buy in the US. Their is obviously a need for this. And from the logistic standpoint, it should be easy for Apple to offer that in the Online Stores itself.
For me the conglusaion is: I stay with my old Macbook Pro and hope i need no replacement within the next years. To order it in germany, ship it to a friend, pay taxes twice (in germany and vur customers) plus shipment, make it to expensive (bottonline: 600-800$ more than buy it in the US) make no sense to me. -
i downloaded mountain lion for my macbook pro and i want to install it on my sisters' macbook air, my question is, how many times can i share my purchase?
Association of Associated Devices is subject to the following terms:
"You may auto-download Eligible Content or download previously-purchased Eligible Content from an Account on up to 10 Associated Devices, provided no more than 5 are iTunes-authorized computers."
That information is available here > iTUNES STORE - MAC APP STORE - TERMS AND CONDITIONS
If you re download Mountain Lion using your Apple ID on her Mac, your sister will need to use your Apple ID and password to install and update apps.
Maybe you are looking for
-
Select list enable / disable in tabular form
Hi, I have created report on (ACT_COA_SEGMENT_MAS) table and this is master table , and created link on this report, when i click on report link, control moves to tabular form that is based on detail table (ACT_SEGMENT_VALUES_MAS) In master table the
-
I have a MacBook pro I recently upgraded to OSX. iPhoto is now not working as it was purchased under an old apple ID and I cant find a way to use my current ID to upgrade it. Also if I delete iPhoto to then repurchase it, will I lose my photo library
-
Hi, Oracle version 10g I have created a partitioned table and it has the below columns: The table is partitioned on the created_date. How data gets inserted into this table: we have a staging table which will get first populated and then using Exchan
-
Record stop and domain "in recovery" status.
Hi, We have a Sun Management Center 3.6.1 in solaris 10, it's install to monitoring the SF25K hardware, it's configure an action by sending an email, into Hardware->Platform Config Reader->Domain->Status. Yesterday, the system generated 2 messages: "
-
Hi, This is a simple question, but some rudimentary searching has not given me a definitive answer: I am moving from the UK to Asia. I am leaving my current laptop, with iTunes 8.2.0.23, in England and will buy a new computer when I arrive, onto whic