MacBook Air is not updating Mac OS X MobileMe

On my iMac, the standard Software Update had two MobileMe updates which changed the icon in the Systems Preferences to MobileMe from .mac . I noticed that this did not happen on my MacBook Air. Then this morning there was as second update to Mac OS X MobileMe 1.1 on my iMac, but again nothing on my MacBook Air. It's System Preferences still reads .mac . I am worried that there will be problems with the email, calendar and contacts pushing unless the MacBook Air is has properly updated software as well.

The mobile me update has not yet shown up for either my MBP or my MBA. I don't know what Apple is using for criteria for software updates for these. It does not make much sense since I do use my dotmac account.

Similar Messages

My macbook air will not update to 10.5.8

when it starts to update it just stop in the begining a does not move

If you click on the apple on the left of the menu bar, and click about this mac, what does it say for version under the OS X?
If it says 10.5.7 or earlier, and Software Update isn't working, you can manually apply 10.5.8. First, download the combo update from http://support.apple.com/kb/DL866. Before applying, bring up Disk Utility (on your hard drive in applications/utilities), and repair permissions on your hard drive. Then install the combo update. When it's done, repair permissions again, then do Software Update for any other related updates.

My Macbook Air does not have a place to check to allow Handoff in my System Preference (General). I have updated to Yosemite.

Trying to use Handoff. I've read where I need to go to the System Preferences - General - and check to allow Handoff. There is no place to checkmark that. I have updated to Yosemite.

What model (i.e., how old) is your MacBook Air? Note the following from Help for that System Preference screen:
Allow Handoff between this Mac and your iCloud devices
(not available on all computers)
If your Mac supports Handoff, select to turn on Handoff between your Mac and iOS devices set up with iCloud. For more information, see Pick up where you left off with Handoff.

My Mac Mail subfolders on my MacBook Air will not sync in alphabetical order. I am assuming it is a setting that I am not finding since my iMac based at my home office is fine, so is my iPad and iPhone. The core source is Exchange.

My Mac Mail subfolders on my MacBook Air will not sync in alphabetical order. I am assuming it is a setting that I am not finding since my iMac based at my home office is fine, so is my iPad and iPhone. The core source is Exchange.

If you have been using the mac.com Apple ID to make iTunes purchases recently, then there should be no issues continuing to use it with the new iPhone. I would abandon the new ID as you will never get Apple to merge the two IDs. I have had a mac.com ID for years and continue to use it with my iPhone 4S.
Tell us the issues that you encounter trying to set up the iPhone with the mac.com account.

Hello, I have purchased and installed Lightroom 5 on my Mac Desktop. I travel with a MacBook Air and would like to have Lightroom 5 on this device as well. The MacBook Air does not have a CD/DVD slot. How do I get Lightroom 5 on my MacBook Air so I can

Hello, I have purchased and installed Lightroom 5 on my Mac Desktop. I travel with a MacBook Air and would like to have Lightroom 5 on this device as well. The MacBook Air does not have a CD/DVD slot. How do I get Lightroom 5 on my MacBook Air so I can use it while travelling?

Adobe - Lightroom : For Macintosh
Just download and install 5.7.1. Don't worry about earlier versions.
You'll need to enter your serial number to license the software.

Macbook air will not connect to the wifi network

I recently had to replace my wireless network router and now my macbook air will not connect to the network. it worked fine with the old wireless router. Now, i get a "unable to join wi-fi network" message. The network ID (SSID) and password (WPA) are the same as before. I try to manually enter the password, but continue to get the previous message.
Any help in figuring out how to correct this problem is greatly appreciated.
Also, I have several PCs in the house that have had zero problems connecting to my wireless with the new router. What am I doing wrong?

Hi,
Ever since did the last airport utility update this has been happening.
I believe the airport utility update is solely a software update. Repair permission and repair disk (boot from your installation disk A) may help.
Other wise, http://osxdaily.com/2009/12/22/mac-wireless-problems-guide-to-troubleshooting-ai rport-wireless-problems-on-your-mac/ may help, too.
Cheers.

My MacBook Air will not turn on. I get a white screen with the apple logo and a spinning star that just does that for hours

My MacBook Air will not turn on. I get a white screen with the apple logo and a spinning star (search icon). It will spin for hours and never go away unless I power off.

Take each of these steps that you haven't already tried. Stop when the problem is resolved.
To restart an unresponsive computer, press and hold the power button for a few seconds until the power shuts off, then release, wait a few more seconds, and press it again briefly.
Step 1
The first step in dealing with a startup failure is to secure the data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since the last backup, you can skip this step.
There are several ways to back up a Mac that is unable to start. You need an external hard drive to hold the backup data.
a. Start up from the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.” The article refers to starting up from a DVD, but the procedure in Recovery mode is the same. You don't need a DVD if you're running OS X 10.7 or later.
b. If Step 1a fails because of disk errors, and no other Mac is available, then you may be able to salvage some of your files by copying them in the Finder. If you already have an external drive with OS X installed, start up from it. Otherwise, if you have Internet access, follow the instructions on this page to prepare the external drive and install OS X on it. You'll use the Recovery installer, rather than downloading it from the App Store.
c. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, start the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
d. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
If the startup process stops at a blank gray screen with no Apple logo or spinning "daisy wheel," then the startup volume may be full. If you had previously seen warnings of low disk space, this is almost certainly the case. You might be able to start up in safe mode even though you can't start up normally. Otherwise, start up from an external drive, or else use the technique in Step 1b, 1c, or 1d to mount the internal drive and delete some files. According to Apple documentation, you need at least 9 GB of available space on the startup volume (as shown in the Finder Info window) for normal operation.
Step 3
Sometimes a startup failure can be resolved by resetting the NVRAM.
Step 4
If a desktop Mac hangs at a plain gray screen with a movable cursor, the keyboard may not be recognized. Press and hold the button on the side of an Apple wireless keyboard to make it discoverable. If need be, replace or recharge the batteries. If you're using a USB keyboard connected to a hub, connect it to a built-in port.
Step 5
If there's a built-in optical drive, a disc may be stuck in it. Follow these instructions to eject it.
Step 6
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to start up, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can start up now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
Step 7
If you've started from an external storage device, make sure that the internal startup volume is selected in the Startup Disk pane of System Preferences.
Start up in safe mode. Note: If FileVault is enabled in OS X 10.9 or earlier, or if a firmware password is set, or if the startup volume is a software RAID, you can’t do this. Post for further instructions.
Safe mode is much slower to start and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know the login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
When you start up in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, the startup volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 11. If you ever have another problem with the drive, replace it immediately.
If you can start and log in in safe mode, empty the Trash, and then open the Finder Info window on the startup volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then restart as usual (i.e., not in safe mode.)
If the startup process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 8
Launch Disk Utility in Recovery mode (see Step 1.) Select the startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then restart as usual.
Step 9
If the startup device is an aftermarket SSD, it may need a firmware update and/or a forced "garbage collection." Instructions for doing this with a Crucial-branded SSD were posted here. Some of those instructions may apply to other brands of SSD, but you should check with the vendor's tech support.
Step 10
Reinstall the OS. If the Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Step 11
Do as in Step 9, but this time erase the startup volume in Disk Utility before installing. The system should automatically restart into the Setup Assistant. Follow the prompts to transfer the data from a Time Machine or other backup.
Step 12
This step applies only to models that have a logic-board ("PRAM") battery: all Mac Pro's and some others (not current models.) Both desktop and portable Macs used to have such a battery. The logic-board battery, if there is one, is separate from the main battery of a portable. A dead logic-board battery can cause a startup failure. Typically the failure will be preceded by loss of the settings for the startup disk and system clock. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
Step 13
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store, or go to another authorized service provider.

My macbook air will not attach mov files to gmail

Not able to attach mov files to gmail. I have a macbook air. this situation has occured over the last couple of weeks and this is not a large file.

Twyla2 wrote:
My Macbook Air will not connect to wifi. I have tried updating the software and still nothing. Any idea how to fix?
Care to share which software you were unsucessful in updating? Which OS version you are using?
===========
Try the basics first:
Change your router channel number. Most times this works & is all you have to do.
Disconnect & reconnect your modem. unplug it for about 10 seconds. Plug it back in. Do the same for Apple’s routers. Wait for everything to reboot.
System Preferences>Network
Click the Assist Me button.
In the next window that pops up, click the Diagnostic button & do the necessary.
Research Knowledge Base for network problems that pertain to the OS that is currently installed on your computer. See these basic networking KB Articles: http://support.apple.com/kb/HT1401 AirPort troubleshooting guide
http://support.apple.com/kb/HT4628 Wi-Fi: How to troubleshoot Wi-Fi connectivity
http://support.apple.com/kb/HT2712 Using network locations in Mac OS X
Manually provided DNS server addresses are higher priority than DHCP's
http://support.apple.com/kb/HT1714 Solutions for connecting to the Internet, setting up a small network, and troubleshooting
============================
What to do when you can't connect to the Internet
Also, run the Airport Utility app which is located inside the Utilities folder.
=====================
If using a Linksys router, contact LinkSys Customer Support and/or post in their forums.
If using Apple's Airport, please re-post over in one of the AirPort Forums.

Hi, my MacBook Air is not working anymore if it's not connected with the power cable. It's pretty new so I can't imagine that the battery is dead already. Why can't I use my MacBook Air without the power cable even though I charged it for hours?

Hi, my MacBook Air is not working anymore if it's not connected with the power cable. It's pretty new so I can't imagine that the battery is dead already. Why can't I use my MacBook Air without the power cable even though I charged it for hours?

Please take the Mac to Apple store to have it checked out.
Genius Bar reservation
http://www.apple.com/retail/geniusbar/
Best.

How can I convert my Open Source document files into Word document files? I cannot download Pages since my Macbook Air does not have the most recent software.

How can I convert my Open Source document files into Word document files? I cannot download Pages since my Macbook Air does not have the most recent software. I downloaded open office to my mac to try and save money. It worked well for a while. Now I get this pop-up message that asks me to "Reopen" and when I select the option, nothing happens. I cannot save my documents anymore and I cannot convert them to word. Help!

dwb wrote:
Does OpenOffice output Word documents by default or do you have to select it manually?
You have 17 options to save as in Open Office, one of which is .doc files, yes it needs to be saved manually.
You may be able to default to DOC, but have not tried same.
Since Open Office is 99% same as Word, I use it, or Word, either one. Open Office is a bit less buggy than Word 11'

My iMessage for my Macbook Air is not working. It says no delivered with a red ! next to it. I have tried serval different options on trying to get it to work to include logging out of iCloud and checking my date and time. I have done about everythin

My iMessage for my Macbook Air is not working. I have updated everything. My system is running on OS X Yosemite Version 10.10. When I go to send a message, it says no delivered with a next to it. I have tried serval different options on trying to get it to work to include logging out of iCloud and checking my date and time and updating FlashPlayer. I have done about everything I can think of. Any help would be greatly appreciate!

Why start a new and very similar thread to your other one which you have not responded to (have you read the replies?)
I suggest that no response is made to this duplicate thread.

Macbook Air is not charging

I have a macbook air that won't charge. My first magsafe adapter wouldn't charge unless it was held at a certain angle so I went and bought a new one. The new one I bought has the exact same problem except now it actually lights up when not held, but it still won't charge when it's not held. I have to put something like my phone under the tip of the charger for it light up and actually charge my computer.
My battery health right now says it is normal. My macbook air is not under warranty anymore since I bought in 2010 and I have tried resetting the SMC. What could the problem be? Does it have to do with the mac itself or do I just have bad luck with magsafe adapters.

My wire is heading towards the hinge. For it to charge I have to sort of lift the the little white cylider thing at the tip of the magsafe. It's sort of hard to explain.
http://upload.wikimedia.org/wikipedia/commons/b/bc/Right_Angle_Magsafe.jpg
It's that little white cyclider part directly under the metalic part. I have to keep holding it or else it won't charge.

When I try to connect the Air with my iPhone to create an Hotspot, it drops the connection and gives an error message in the iPhone saying that the device (MacBook Air) is not supported. What can i do about it?

When I try to connect the Air with my iPhone to create an Hotspot, it drops the connection and gives an error message in the iPhone saying that the device (MacBook Air) is not supported. What can i do about it?

The problem has been fixed with the most recent OS X software update.

IMessage on my macbook air will not connect.

iMessage on my macbook air will not connect. It says "Could not sign in. Please check your network connection and try again." I have gone through all the support instructions and a lot of these discussion chats. I have sign out of it and my phone and resigned in. I have checked that everything is verified and connected. My ios is up to date on both my computer and phone. It worked fine until about a week ago and suddenly it stopped
Thank you for your assistance!

Hi,
In Hard Drive/Library/Fonts do you have the AppleGothic.ttf Font.
The iMessages account uses this to "register".
If the computer has been Off then the App effectively "registers" the Apple ID again.
It cannot do this is the Font is "missing".
The thread I saw that highlighted this as an issues said the font could be downloaded from Apple but not the "how" of that.
8:08 pm Wednesday; July 16, 2014
 iMac 2.5Ghz i5 2011 (Mavericks 10.9)
 G4/1GhzDual MDD (Leopard 10.5.8)
 MacBookPro 2Gb (Snow Leopard 10.6.8)
 Mac OS X (10.6.8),
 Couple of iPhones and an iPad

MacBook Air SMC Firmware Update v2.0 update available again and again. How do I fix it?

I have installed MacBook Air SMC Firmware Update v2.0 three times and I still get an update available notification asking to install it again. This is a mid-13 MacBook Air running OSX 10.9.3. System info lists the SMC version as 2.13f7.
Does anyone know how to resolve this issue?

Hi,
- Are there any status or error messages in /var/log/install.log
- The Firmware version it should install is 2.12f137
- If there isn't anything in the log try:
Intel-based Macs: Resetting the System Management Controller (SMC)
and/or About NVRAM and PRAM
and check whether there is installation.
If no install, try OS X: What is Safe Boot, Safe Mode
then reboot normal, try the install again.
Hope this helps

MacBook Air is not updating Mac OS X MobileMe

Similar Messages

Maybe you are looking for