Macbook has a restless sleep.

Hello all,
When I close my macbook pro it sometimes just won't get to sleep. When I listen to it with my ear pressed to it I can the harddrive spinning, slowing down and getting silent(like it is going to sleep) but the moment it is silent, the drive starts up again. And this keeps repeating itself.
The indicator light shows somewhat the same information. It dims slowly but then brightens up quickly and stays bright for like 5 sec. Then it dims again ect.
Like I said, the problem doesn't alawys occur.
And removing the power cable before closing won't work either.
Faray

Run fsck.
1. Reboot/Startup holding your Command-S key down.
2. At the command line type the following and hit 'Return.'
/sbin/fsck -fy
3. If it finds a problem and repairs it, immediately run fsck again until the drive checks OK.
4. After it has check/repaired your disk, type 'reboot' and hit 'Return' again. Unit should bootup normally.
=======
Try resetting your SMC.
Resetting the System Management Controller >>
Dave M.
MacOSG Founder/Ambassador  An Apple User Group  iTunes: MacOSG Podcast
Creator of 'Mac611 - Mobile Mac Support' (designed exclusively for an iPhone/iPod touch)

Similar Messages

  • My MacBook has stopped sleeping!

    Hi there everyone,
    I've just noticed that in the last two days, when I just leave my mac (with only finder running) it doesn't sleep anymore. I went to system preferences, and told it to sleep after 1 minute.. (i haven't turned sleeping off or anything). As expected, after 1 minute, the screen went blank, but was just running on low power, and didn't go into sleep. Last night, as usual, I played an album on itunes as i wnt to sleep. Usually, the album finishes, the mac sleeps, and in the morning it's got battery of about 90%. However, with it not sleeping anymore, in the morning it was on 0% and had gone into a coma - only plugging the mains in could wake it up.
    However, when i just close the mac up, it has no problems going to sleep... so the problem is when I leave it open, it just doesn't sleep.
    Obviously slightly concerning... can anyone shed any light?
    Many thanks

    Hey- My MacBook Is haveing a simular problem- it does not go to sleep when left alone. And when i close my MacBook It does not sleep at all-I have called tech support and they told me to do this-un-Plug your power supplie-and take you battery out- and replace everything-With power adapter. Then turn on your computer-
    I have found that it did not work-I am going to bring my mac to the apple store and see if they can ether fix it or replace the computer-Maybe this will work for your promblem-
    -----John

  • Macbook Pro Stuck in Sleep Mode

    My macbook pro went to sleep and wouldn't wake up. This has happened a few times before and was usually cured by just holding down the power button to turn it off then turning it back on. This time that's not working though.
    When I try to turn it back on only the little power light comes on and the disc in the drive spins up, but that's all the further it gets. There is no chime and nothing is displayed on the screen.
    Anyone know what the problem might be and anyway to fix it? Tried clearing the pram, but that did nothing.
    Hope it isn't major as I'm a month out of warranty ... plus the nearest store is over an hour away.

    Well, after more searching around the internet, I found that sleep mode and bad ram make the front light do the same thing. So after my restart it was stuck in some kind of sleep mode coma, the ram must have died when I forced it to power down. Once I took out my corsair ram and threw the original stick that came with it back in, it fired up.
    Hope this helps someone else.

  • Macbook Pro Randomly Enters Sleep Mode For A Few Seconds

    Hi All,
    My Macbook Pro has had this problem since a few months after I purchased it. While working or playing the laptop will randomly go into what seems like sleep mode. The screen turns off, I hear the hard drive stop and then a couple seconds later it starts back up on its own. Any Internet connection I had disconnects, but other than that it starts up as normal.
    The problem comes and goes and doesn't seem to be consistent with anything that I'm aware of. Sometimes it happens once, then doesn't happen for days. Often it will happen several times in a row over the course of an hour.
    I've called support and brought the laptop to the genius bar where they ran several tests, but were unable to figure anything out. Research online has shown similar issues with other users, but no solutions. The laptop is not stacked on anything magnetic, the issue occurs when running hot or cold and whether I'm on battery power or plugged in.
    Any help would be greatly appreciated. If this can't be resolved is it something I can bring to apple and get a replacement under my year warranty?
    Specs are below:
    Refurbished 17" Macbook Pro
    Processor Name: Intel Core 2 Duo
    Processor Speed: 2.66 GHz
    *Console Log from one pretty bad incident today:*
    Aug 13 12:55:52 Ben-Shepards-MacBook-Pro coconutBattery[1857]: * NSTimer ignoring exception '* -[NSCFArray objectAtIndex:]: index (2) beyond bounds (1)' that raised during firing of timer with target 0x405e00 and selector 'batteryDataThreadTimer:'
    Aug 13 12:58:10: --- last message repeated 8 times ---
    Aug 13 12:58:32 Ben-Shepards-MacBook-Pro loginwindow[31]: loginwindow SleepWakeCallback WILL sleep
    Aug 13 12:58:34 Ben-Shepards-MacBook-Pro configd[13]: network configuration changed.
    Aug 13 12:58:37 Ben-Shepards-MacBook-Pro loginwindow[31]: loginwindow SleepWakeCallback will power on, Currenttime:8/13/2010 12:58:37.034 PM - Waketime:8/13/2010 12:58:35.400 PM = Deltatime:1.633561075
    Aug 13 12:58:39 Ben-Shepards-MacBook-Pro configd[13]: Sleep: Success - AC 96 - Clamshell Sleep
    Aug 13 12:58:39 Ben-Shepards-MacBook-Pro configd[13]: Wake: Success - AC 96 - EC LID0
    Aug 13 12:58:39 Ben-Shepards-MacBook-Pro configd[13]: Hibernate Statistics
    Aug 13 12:58:40 Ben-Shepards-MacBook-Pro configd[13]: network configuration changed.
    Aug 13 12:58:58 Ben-Shepards-MacBook-Pro ntpd[18]: time reset +0.908918 s
    Aug 13 12:59:08 Ben-Shepards-MacBook-Pro loginwindow[31]: no spins reported for this wake
    Aug 13 13:00:48 Ben-Shepards-MacBook-Pro loginwindow[31]: loginwindow SleepWakeCallback WILL sleep
    Aug 13 13:00:50 Ben-Shepards-MacBook-Pro configd[13]: network configuration changed.
    Aug 13 13:00:53 Ben-Shepards-MacBook-Pro loginwindow[31]: loginwindow SleepWakeCallback will power on, Currenttime:8/13/2010 1:00:53.031 PM - Waketime:8/13/2010 1:00:51.420 PM = Deltatime:1.611223936
    Aug 13 13:00:53 Ben-Shepards-MacBook-Pro configd[13]: PMConnection mDNSResponder com.apple.powermanagement.applicationresponse.slowresponse 128 ms
    Aug 13 13:00:53 Ben-Shepards-MacBook-Pro configd[13]: PMConnection AirPort configd plug-in com.apple.powermanagement.applicationresponse.slowresponse 128 ms
    Aug 13 13:00:53 Ben-Shepards-MacBook-Pro configd[13]: PMConnection IPConfiguration com.apple.powermanagement.applicationresponse.slowresponse 130 ms
    Aug 13 13:00:55 Ben-Shepards-MacBook-Pro configd[13]: Sleep: Success - AC 97 - Clamshell Sleep
    Aug 13 13:00:55 Ben-Shepards-MacBook-Pro configd[13]: Wake: Success - AC 97 - EC LID0
    Aug 13 13:00:55 Ben-Shepards-MacBook-Pro configd[13]: Hibernate Statistics
    Aug 13 13:00:56 Ben-Shepards-MacBook-Pro configd[13]: network configuration changed.
    Aug 13 13:01:07 Ben-Shepards-MacBook-Pro ntpd[18]: time reset +0.836731 s
    Aug 13 13:01:24 Ben-Shepards-MacBook-Pro loginwindow[31]: no spins reported for this wake
    Aug 13 13:04:59 Ben-Shepards-MacBook-Pro loginwindow[31]: loginwindow SleepWakeCallback WILL sleep
    Aug 13 13:05:02 Ben-Shepards-MacBook-Pro configd[13]: network configuration changed.
    Aug 13 13:05:05 Ben-Shepards-MacBook-Pro loginwindow[31]: loginwindow SleepWakeCallback will power on, Currenttime:8/13/2010 1:05:05.026 PM - Waketime:8/13/2010 1:05:03.410 PM = Deltatime:1.616448998
    Aug 13 13:05:07 Ben-Shepards-MacBook-Pro configd[13]: Sleep: Success - AC 98 - Clamshell Sleep
    Aug 13 13:05:07 Ben-Shepards-MacBook-Pro configd[13]: Wake: Success - AC 98 - EC LID0
    Aug 13 13:05:07 Ben-Shepards-MacBook-Pro configd[13]: Hibernate Statistics
    Aug 13 13:05:08 Ben-Shepards-MacBook-Pro configd[13]: network configuration changed.
    Aug 13 13:05:10 Ben-Shepards-MacBook-Pro ntpd[18]: bind() fd 26, family 30, port 123, scope 5, addr fe80::223:6cff:fe96:9643, in6is_addrmulticast=0 flags=0x11 fails: Can't assign requested address
    Aug 13 13:05:10 Ben-Shepards-MacBook-Pro ntpd[18]: unable to create socket on en1 (51) for fe80::223:6cff:fe96:9643#123
    Aug 13 13:05:17 Ben-Shepards-MacBook-Pro ntpd[18]: time reset +0.413090 s
    Aug 13 13:05:36 Ben-Shepards-MacBook-Pro loginwindow[31]: no spins reported for this wake
    Aug 13 13:05:39 Ben-Shepards-MacBook-Pro loginwindow[31]: loginwindow SleepWakeCallback WILL sleep
    Aug 13 13:05:39 Ben-Shepards-MacBook-Pro mDNSResponder[30]: DeregisterInterface: Frequent transitions for interface en1 (FE80:0000:0000:0000:0223:6CFF:FE96:9643)
    Aug 13 13:05:42 Ben-Shepards-MacBook-Pro configd[13]: network configuration changed.
    Aug 13 13:05:44 Ben-Shepards-MacBook-Pro loginwindow[31]: loginwindow SleepWakeCallback will power on, Currenttime:8/13/2010 1:05:44.024 PM - Waketime:8/13/2010 1:05:42.410 PM = Deltatime:1.614192009
    Aug 13 13:05:46 Ben-Shepards-MacBook-Pro configd[13]: Sleep: Success - AC 98 - Clamshell Sleep
    Aug 13 13:05:46 Ben-Shepards-MacBook-Pro configd[13]: Wake: Success - AC 98 - EC LID0
    Aug 13 13:05:46 Ben-Shepards-MacBook-Pro configd[13]: Hibernate Statistics
    Aug 13 13:05:47 Ben-Shepards-MacBook-Pro configd[13]: network configuration changed.
    Aug 13 13:05:47 Ben-Shepards-MacBook-Pro mDNSResponder[30]: RegisterInterface: Frequent transitions for interface en1 (192.168.1.103)
    Aug 13 13:05:48 Ben-Shepards-MacBook-Pro ntpd[18]: bind() fd 26, family 30, port 123, scope 5, addr fe80::223:6cff:fe96:9643, in6is_addrmulticast=0 flags=0x11 fails: Can't assign requested address
    Aug 13 13:05:48 Ben-Shepards-MacBook-Pro ntpd[18]: unable to create socket on en1 (54) for fe80::223:6cff:fe96:9643#123
    Aug 13 13:05:51 Ben-Shepards-MacBook-Pro mDNSResponder[30]: RegisterInterface: Frequent transitions for interface en1 (FE80:0000:0000:0000:0223:6CFF:FE96:9643)
    Aug 13 13:05:59 Ben-Shepards-MacBook-Pro ntpd[18]: time reset +1.150003 s
    Aug 13 13:06:04 Ben-Shepards-MacBook-Pro loginwindow[31]: loginwindow SleepWakeCallback WILL sleep
    Aug 13 13:06:04 Ben-Shepards-MacBook-Pro mDNSResponder[30]: DeregisterInterface: Frequent transitions for interface en1 (FE80:0000:0000:0000:0223:6CFF:FE96:9643)
    Aug 13 13:06:05 Ben-Shepards-MacBook-Pro configd[13]: PMConnection AirPort configd plug-in com.apple.powermanagement.applicationresponse.slowresponse 225 ms
    Aug 13 13:06:05 Ben-Shepards-MacBook-Pro configd[13]: PMConnection mDNSResponder com.apple.powermanagement.applicationresponse.slowresponse 225 ms
    Aug 13 13:06:05 Ben-Shepards-MacBook-Pro configd[13]: PMConnection IPConfiguration com.apple.powermanagement.applicationresponse.slowresponse 225 ms
    Aug 13 13:06:07 Ben-Shepards-MacBook-Pro configd[13]: network configuration changed.
    Aug 13 13:06:11 Ben-Shepards-MacBook-Pro loginwindow[31]: loginwindow SleepWakeCallback will power on, Currenttime:8/13/2010 1:06:11.026 PM - Waketime:8/13/2010 1:06:09.410 PM = Deltatime:1.616049945
    Aug 13 13:06:13 Ben-Shepards-MacBook-Pro configd[13]: Sleep: Success - AC 98 - Clamshell Sleep
    Aug 13 13:06:13 Ben-Shepards-MacBook-Pro configd[13]: Wake: Success - AC 98 - EC LID0
    Aug 13 13:06:13 Ben-Shepards-MacBook-Pro configd[13]: Hibernate Statistics
    Aug 13 13:06:14 Ben-Shepards-MacBook-Pro configd[13]: network configuration changed.
    Aug 13 13:06:14 Ben-Shepards-MacBook-Pro mDNSResponder[30]: RegisterInterface: Frequent transitions for interface en1 (192.168.1.103)
    Aug 13 13:06:15 Ben-Shepards-MacBook-Pro ntpd[18]: bind() fd 26, family 30, port 123, scope 5, addr fe80::223:6cff:fe96:9643, in6is_addrmulticast=0 flags=0x11 fails: Can't assign requested address
    Aug 13 13:06:15 Ben-Shepards-MacBook-Pro ntpd[18]: unable to create socket on en1 (57) for fe80::223:6cff:fe96:9643#123
    Aug 13 13:06:18 Ben-Shepards-MacBook-Pro mDNSResponder[30]: RegisterInterface: Frequent transitions for interface en1 (FE80:0000:0000:0000:0223:6CFF:FE96:9643)
    Aug 13 13:06:24 Ben-Shepards-MacBook-Pro ntpd[18]: time reset -0.427840 s
    Aug 13 13:06:41 Ben-Shepards-MacBook-Pro loginwindow[31]: no spins reported for this wake
    Message was edited by: Shep123

    I just found this link and have followed the instructions. Here's hoping...
    http://discussions.apple.com/thread.jspa?messageID=11716177&#11716177

  • Why does my Macbook keep going to sleep every 10-20 secs!

    why does my Macbook keep going to sleep every 10-20 secs when first turning on then it seems ok after about 10 mins ? This has only happened since upgrding to Lion 3 days ago, it's driving me mad!

    You are most welcome

  • MacBook Pro goes to sleep when copying files from attached drives

    I have noticed that since installing Yosemite my MacBook Pro goes to sleep when it is in the middle of copying a large number of files.  When I wake it up the copying continues.
    I have also noticed that when I am watching videos from my shared iTunes library on an Apple TV the video will stop after about 15 minutes and the connection to the library is lost because the MacBook Pro has gone to sleep. When woken up then access to the library is restored but I need to reselect the movie and then resume.
    I have changed the power saving options to do not let drives sleep when idle and do not sleep laptop.
    Anyone else have any experience of this or better still a fix.
    Thanks in advance.

    I have just found that if I turn off the display sleep in the power settings then the problem is resolved.  It means though that the screen on my MacBook Pro is on all the time albeit with a screen saver.

  • MacBook Extremely Slow to Sleep - Help!

    My macbook has always taken under 10 seconds to launch into sleep mode (either from apple menu or closed top). In the last 3 weeks however, the time to sleep (ie: screen off, blinking light) is appx 40-50 seconds. I'm not sure what has happened. I know there are 3rd party software options to reduce the time to launch into sleep, but what I'm looking for is a way to debug my machine to restore it to it's past performance level. Past posts have indicated that problems can be found in the console posts, however I am not confident of my ability to diagnose anything from these. Can anyone help? Here are the Console posts from today:
    3/26/10 8:39:40 AM com.apple.backupd-attach[49] Not starting scheduled Time Machine backup - computer is on battery power.
    3/26/10 8:39:50 AM com.apple.launchd.peruser.501[83] (com.apple.ReportCrash) Falling back to default Mach exception handler. Could not find: com.apple.ReportCrash.Self
    3/26/10 8:39:52 AM com.apple.launchd.peruser.501[83] (com.apple.Kerberos.renew.plist[104]) Exited with exit code: 1
    3/26/10 8:41:17 AM com.apple.WebKit.PluginAgent[124] Debugger() was called!
    3/26/10 9:03:37 AM com.apple.WebKit.PluginAgent[124] Debugger() was called!
    3/26/10 9:03:47 AM com.apple.WebKit.PluginAgent[124] Debugger() was called!
    3/26/10 9:04:21 AM com.apple.WebKit.PluginAgent[124] Debugger() was called!
    3/26/10 9:05:30 AM com.apple.WebKit.PluginAgent[124] Debugger() was called!
    3/26/10 9:06:18 AM com.apple.WebKit.PluginAgent[124] Debugger() was called!
    3/26/10 9:06:42 AM com.apple.WebKit.PluginAgent[124] Debugger() was called!
    3/26/10 9:06:44 AM com.apple.WebKit.PluginAgent[124] Debugger() was called!
    3/26/10 9:19:08 AM SystemUIServer[88] It does not make sense to draw an image when [NSGraphicsContext currentContext] is nil. This is a programming error. Break on _NSWarnForDrawingImageWithNoCurrentContext to debug. This will be logged only once. This may break in the future.
    3/26/10 9:38:00 AM [0x0-0x19019].backupd-helper[215] Not starting scheduled Time Machine backup - computer is on battery power.
    3/26/10 9:39:38 AM com.apple.backupd-auto[233] Not starting scheduled Time Machine backup - computer is on battery power.
    3/26/10 9:44:06 AM com.apple.WindowServer[59] Fri Mar 26 09:44:06 e-henneberrys-macbook.local WindowServer[59] <Error>: kCGErrorFailure: Set a breakpoint @ CGErrorBreakpoint() to catch errors as they are logged.
    3/26/10 9:44:06 AM [0x0-0x20020].backupd-helper[254] Not starting scheduled Time Machine backup - computer is on battery power.
    3/26/10 9:45:46 AM [0x0-0x23023].backupd-helper[272] Not starting scheduled Time Machine backup - computer is on battery power.
    3/26/10 10:00:15 AM com.apple.WebKit.PluginAgent[124] Debugger() was called!
    3/26/10 10:01:19 AM [0x0-0x27027].backupd-helper[307] Not starting Time Machine backup after wake - failed to resolve alias to backup volume
    3/26/10 10:02:14 AM com.apple.WebKit.PluginAgent[124] Debugger() was called!
    Thanks!

    Thanks for your reply. I turned Time Machine to the "off" setting, but nothing seems to have changed. The console post immediately following putting the computer in sleep mode seems to be this one:
    3/26/10 4:59:59 PM com.apple.WindowServer[65] Fri Mar 26 16:59:59 e-henneberrys-macbook.local WindowServer[65] <Error>: kCGErrorFailure: Set a breakpoint @ CGErrorBreakpoint() to catch errors as they are logged.
    Thanks for your help.

  • MacBook won't automatically sleep

    My MacBook won't automatically sleep anymore. If I close the lid or command it to sleep, it will. But it will no longer automatically sleep. I've tried tons of fixes and searched for hours on the internet, but still have not found a solution. I seem to have noticed that this starting happening after I installed Windows XP via Bootcamp, so I'm guessing that the problem is related to that. Any ideas?

    This is for a Mac that won't sleep.
    Here is KB article HT1776 with their tips.
    Mine follow;
    USB devices and hubs often cause Macs to not sleep or wake quickly from sleep (notably HP printers and scanners, HP all in ones, and Cannon scanners). Disconnect all USB except for keyboard and mouse and try. If it sleeps, add one back at a time testing after each one to find the culprit.If you've set your Mac to receive faxes, it may not be able to sleep. It might also have a damaged preferences file.
    If you use your Mac for faxing, open System Preferences. click Print & Fax, click the Faxing tab, and uncheck the Receive Faxes On This Computer box.
    If that doesn't work or you've never faxed on your Mac, go to Finder/Hard Drive /Library/Preferences/SystemConfiguration and delete the com.apple.PowerManagement.plist and com..apple.AutoWake.plist files (if your Mac asks, type your admin. password).
    If the latter file isn't present in the folder, go to user name(probably your name)/Library/Preferences, delete the com.apple.systemuiserver.plist file, and reboot your Mac.
    Hope this helps!
    P.S. One member here reported this (Michael Gleason);
    "I have had this problem with my IMac G5. It is surprisingly irritating. LaCie's Silverkeeper backup software was the cause. By default it gave itself permission to wake up the computer to check if a backup was needed. Do you have this or a similar program installed which has scheduled activities including wake-up permissions as an option?"
    Dave Hamilton provided this link, xlr8yourmac.com, to a member, which addresses failure of deep sleep with some users that updated and added new FireWire and USB card.
    Also, here is Apple KB article TA2469 about PCI cards and sleep.
    tomhorvat adds this; After few days of messing around I found out that I had desktop background (wallpaper) set to change every 1 minute.
    After unchecking "Change picture..." in system preferences (under Desktop/Screen saver), my powerbook went to sleep all by itself.
    Tristan Currier noticed this; "I have a Canon printer(shared) and my imac would not sleep. I opened up printer/fax in system prefs and noticed it said the printer was in use when it was off. Opened up the printer queue and noticed about 7 pending documents. Deleted them all and now it sleeps.
    Check the printer queue!"
    Allan Jones says "sometimes there is Network activity: launch System Preferences > Energy Saver > "Options" tab and uncheck "Wake for Ethernet network administrator access."
    Good Luck!  DALE

  • My macbook has recently started getting really hot after using it for a brief time, is there something wrong

    Hi
    My macbook has started getting really hot after using it for only maybe 10 minutes or so, it can go up to 73 degrees quite quickly, I am only surfing the net etc but have a few pages open at the same time.
    Also should I switch it off after I finish using it or is it ok to leave it in sleep mode for long periods of time......
    it is about 1 year old
    thanks

    First try a SMC reset:
    http://support.apple.com/kb/ht3964
    If there is no change, install istat menus:
    http://bjango.com/mac/istatmenus/
    Open Activity Monitor to ALL PROCESSES and %CPU to display values from high to low.
    Look for a process that consumes a large % of CPU.
    You may post images of both for inspection.
    Ciao.

  • Retina Macbook Pro Freezes after sleeping...

    Hello, I just purchased a brand new macbook pro retina (13inch) base model. Its been really annoying to have to force shut down the computer almost everytime it has been asleep for a while and I open the computer to type in my password. Everything is up to date and I have no idea what is causing this. I wouold love to find out if there is anything I can do before I return my Retina Macbook Pro. Anyone's help would be super awesome. Thank you!

    Hi,
    I have a late 2012 13 inch Retina and have exactly the same problem since the last EFI V1.1 update. This update is supposed to enhance performances during sleep, but now the MacBook is hotter in sleep than in wake!
    Before the update, there where no sleep problem, but now
    Hop Apple's guy will see this post, if not I’ll call support next week.
    Regards.

  • Macbook on Snow Leopard Sleep freeze, slow boot time, blue screen, ... etc.

    The macbook has the following problems:
    1. When closing the lid or pressing the power button the computer freezes, the fans start spinning fast it stays like that until it drains the battery. This happens every time.
    2. Start-up times are very long, like 3 or 4 minutes. This also happens every time.
    3. Now after a fresh snow leopard install it doesn't even start up completely, as it stays with the blue background and I can hear the music of the introductory animation.
    The macbook worked ok with the factory installed Tiger. The SL DVD is OK, as its installation has been tested on another Mac. The machine's advanced hardware test passed successfully. Resetting Pram and similar actions were unsuccessful as solving the problem.
    I don't know what else to do... please help.

    So mine started doing some of the same things. It freezes when it goes into sleep mode. Then it starts to get really really hot and the drive starts spinning fast. It also takes a very long time to boot up. And it's unresponsive sometimes. I've wiped the drive and reinstalled a few times, but it's still like that. I don't know what's wrong.

  • When my macbook pro wakes from sleep the curser is not there, no keys work and the screen is frozen so i have to reboot it

    Sometimes when my macbook pro wakes from sleep the curser has disappeared, the screen is frozen and no keys work. I have to reboot.

    Please read this whole message before doing anything.
    This procedure is a diagnostic test. It’s unlikely to solve your problem. Don’t be disappointed when you find that nothing has changed after you complete it.
    The purpose of the test is to determine whether the problem is caused by third-party software that loads automatically at startup or login, by a peripheral device, or by corruption of certain system caches. 
    Disconnect all wired peripherals except those needed for the test, and remove all aftermarket expansion cards. Boot in safe mode and log in to the account with the problem. Note: If FileVault is enabled on some models, or if a firmware password is set, or if the boot volume is a software RAID, you can’t do this. Ask for further instructions.
    Safe mode is much slower to boot and run than normal, and some things won’t work at all, including sound output and  Wi-Fi on certain models. The next normal boot may also be somewhat slow.
    The login screen appears even if you usually log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin. Test while in safe mode. Same problem? After testing, reboot as usual (i.e., not in safe mode) and verify that you still have the problem. Post the results of the test.

  • How will an external Hard drive designed for the macbook Pro work with my White Macbook?  My  white macbook has a Firewire 400 and the G-Tech HD has a 800 to 400 compatible cable for the firewire.

    I am asking this because I want the G-Tech Hard drive  says that it is designed for the macbook pro.  Yet, I want to back up faster with by using my firewire 400 which is not an option on the one designed for the white macbook that does not have a firewire (only a USB port.)  The G-Tech Hard drive comes with the 800 to 400 compatible cable and has 5400 RPM with 750 GB.  Also, I've heard that laptops with low battery (mine all the time)  won't have the power for a bus powered Hard drive (as in no ac plug in adaptor.)  Can I just plug in my laptop?  Any one know the answers from experience with this hard drive?

    As far as I know, if a harddrive works with a Macpro, it should work with the Macbook: if your Macbook is low on power, plug in the AC adapter
    If your Macbook has a firewire port, then it should be fine. BUt i would do somemore research first.

  • Cannot move any files into trash to delete them. I get a Trash warning box saying "The Finder cannot complete the operation because some data in 'file name' could not be read or written.(Error code - 36)".Macbook has so much data it is almost not working

    Cannot move any files into trash to delete them. I get a Trash warning box saying "The Finder cannot complete the operation because some data in 'file name' could not be read or written.(Error code - 36)".Macbook has so much data it is almost not working.
    I have tried reseting to factory settings by removing battery and holding down the power switch for more than 5 sec but this does nothing.
    Any ideas would be greatly appreciated as I think with so much unwanted data on the desktop and other places the whole os will crash very soon.
    Thanks, Rick

    The hard drive may be dying anyway, or the directory damaged because it is so full.  You should never let the hard drive get over 85% full.
    A -36 error is a read/write error.
    All you did with the power is reset the SMC.  Does nothing to reset everything to factory settings. 
    Do you have your original 10.4 installer discs for the MacBook?
    Is your data backed up?

  • Regarding Mail:  When I return to my computer after it has gone to sleep, my accounts go offline, and are always asking me for the password.  THis is very annoying.  How can I prevent this?

    Regarding Mail:  When I return to my computer after it has gone to sleep, my accounts go offline, and are always asking me for the password.  THis is very annoying.  How can I prevent this?

    Back up all data.
    Launch the Keychain Access application in any of the following ways:
    ☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
    ☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
    ☞ Open LaunchPad. Click Utilities, then Keychain Access in the icon grid.
    Select the login keychain from the list on the left side of the Keychain Access window. If your default keychain has a different name, select that.
    If the lock icon in the top left corner of the window shows that the keychain is locked, click to unlock it. You'll be prompted for the keychain password, which is the same as your login password, unless you've changed it.
    Right-click or control-click the login entry in the list. From the menu that pops up, select Change Settings for Keychain "login". In the sheet that opens, uncheck both boxes, if not already unchecked.
    From the menu bar, select
    Keychain Access ▹ Preferences ▹ First Aid
    If the box marked Keep login keychain unlocked is not checked, check it.
    Select
    Keychain Access ▹ Keychain First Aid
    from the menu bar and repair the keychain. Quit Keychain Access.

Maybe you are looking for

  • How to extract data from a Infoset in SQ02?

    Hi,    I wish to extract data from a infoset in SQ02, how do i link a infosource with this infoset?    Any advise is welcomed. Thanks, CK

  • System.exec() in jdk.15 and later

    HI there I have used System.exec() in jdk 1.4 and I came across that, in jdk 1.5 and later you have better way to do the same thing. Can anyone help how to make it better with jdk 1.5 and later. Thanks Arif.

  • About Logon page

    Hi All, I have the following requirement. I am developing a BSP application that will be run in intranet by end users. As usual like for all the applications, when I test this application the system asks me for userid and password to the server for a

  • When I try to download an app why does it pop up a different Apple ID

    I need help because I changed the password and the Apple ID and it's still saying a different ID

  • How do you copy and paste an adjustment layer to the center of a new doc?

    Hi, I know I can drag an adjustment layer to a new document, but it's never in the center. So I end up with an image with adjustments made, but not across the whole image. Therefore I have to eyeball and properly center the adjustment layer to make s