Macbook Pro 13" problems opening apps, installing updates and lag.

Hey guys i got a Macook Pro 13" a few months ago and now I cant open itunes or limewire and a few other applications. They just bounce for 30 seconds and i get a message that it's unexpectedly quit and the options if i wana report it or not. I've done repair permissions made a new account and still no progress. I've inserted the cd it came with to do a hardware test and as its booting back up I hear a click sound and everything shuts off. Another thing to add is that there is alot of lag takes awhile for it to open up the finder files.
Is this a RAM problem? I went to about this computer and it says the status is ok and iv taken out 1 of 2 of my rams twice too see if the problem still continued and it did. Or am I going to need a new hard drive?
Iv also tried to do a software update but as im installing it i get the unexpected quit error again.
please help

The 1600MHz RAM "should" work on a system that has a 1333MHz bus, since it is only going to down-clock the RAM; however, the system was not tested with this configuration and there may be unexpected behaviors from it.
If it's not specifically a compatibility issue with the speed ratings, it may be an issue with bad sectors in the RAM itself. To test this, load the Apple Hardware Test suite by booting your system with the "D" key held down (or Option-D to load the tools from the Internet). When the tools load, check the box for the extended memory test and run it. This will take several hours to complete, but will report any bad memory addresses it finds.
If you find any bad addresses, then you should be able to return the RAM for a replacement since most manufacturers supply lifetime warranties for RAM modules.

Similar Messages

  • Macbook pro won't boot after installing update 10.9.3

    macbook pro won't boot after installing update 10.9.3

    Please read this whole message before doing anything.
    This procedure is a diagnostic test. It’s unlikely to solve your problem. Don’t be disappointed when you find that nothing has changed after you complete it.
    The purpose of the test is to determine whether the problem is caused by third-party software that loads automatically at startup or login, by a peripheral device, by a font conflict, or by corruption of the file system or of certain system caches.
    Disconnect all wired peripherals except those needed for the test, and remove all aftermarket expansion cards, if applicable. Start up in safe mode.
    Note: If FileVault is enabled, or if a firmware password is set, or if the startup volume is a Fusion Drive or a software RAID, you can’t do this. Ask for further instructions.
    Safe mode is much slower to start up and run than normal, with limited graphics performance, and some things won’t work at all, including sound output and Wi-Fi on certain models. The next normal startup may also be somewhat slow.
    The login screen appears even if you usually login automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
    Test while in safe mode. Same problem?
    After testing, restart as usual (not in safe mode) and verify that you still have the problem. Post the results of the test.

  • Macbook pro starts up , opens bootcamp into win7, and all mac users except one

    I have macbook pro that has always worked like a charm. Yesterday I started it and it opens to screen with choice of users. I clicked on my account and it went through motions and took me back to original screen. I checked and was able to pen all other accounts. I restarted and was able to open in windows as well. Logged in as another user with admin priveliges I created a new admin user. I was able to open locked admin functions with new account and password for account unable to open. I verified HD and permissions. Next thing will be to boot from system disk and repar permissions. Any ideas....Never seen anything like this in 20 years

    I have macbook pro that has always worked like a charm. Yesterday I started it and it opens to screen with choice of users. I clicked on my account and it went through motions and took me back to original screen. I checked and was able to pen all other accounts. I restarted and was able to open in windows as well. Logged in as another user with admin priveliges I created a new admin user. I was able to open locked admin functions with new account and password for account unable to open. I verified HD and permissions. Next thing will be to boot from system disk and repar permissions. Any ideas....Never seen anything like this in 20 years

  • I have a macbook pro with no OS, original install discs and internet recovery is not working.  Can I purchase an OS (like snow leopard) and install that onto macbook?

    I have recently purchased a macbook pro 2011 that does not have original install discs.  The macbook does not currently have an OS and internet recovery does not work.  Am I able to purchase an OS like Snow Leopard that actually has a disc and install it onto this macbook?

    Does your Mac meet the hardware specs for Snow Leopard?
    Mac computer with an Intel processor
    1GB of memory
    5GB of available disk space
    DVD drive for installation
    Allan

  • Iphone and MacBook Pro will not open App store

    I am assuming that this must be a wifi thing. For a while now I was only able to use my iphone with "guest" login from my home network for reasons I do not know... Anyway, both my iphone and my Mac cannot connect to the app store.
    I went to the router website/support page and it states everything is working correctly.
    Wondering if I did something somehow to have my devices not detect my router/modem?
    (And... why only the app store? They both connect to the internet fine.)
    Thank you in advance!

    Which OSX & version.  There are several. 

  • Macbook pro has been wiped after an update and the majority of the contents has been lost, is there anything I can do to recover it?

    I updated my laptop and now the majority of my contents seem to have been wiped.  Is there anything I can do to recover them? My backup was connected at the time so it has already backed-up to the computer's present state.  Most photos/ Itunes/ Mail... has been lost.  I have some stuff but only up until January 2013.

    If all your files are missing
    You may have logged in as a different user, such as Guest. Open the Users & Groups pane in System Preferences. Your name should be at the top of the user list, under Current User. See also this support article. 
    If files are missing from one folder
    Change the Finder view mode; for example, from icon view to list view, or vice versa.
    If files are present, but seem outdated
    You may have started up from a different volume (disk.) Open the Startup Disk preference pane and check the selection.

  • Macbook Pro received kernel panic from Mavericks update and will not turn on

    Hi, I have a 2011 MBP and have had kernel panics since updating to Mavericks. Even in safe mode the computer just teuns on shows the kernel panic and then auto restarts and does this about three times before it shuts off completely. I have been informed the some of the hardware is not capable of running this software but even so I cannot even put MBP back to Mountain Lion. If anyone is having similar issue please let me know and any help would be great.

    Take it in for a service diagnostic so you can determine if it's worth fixing or if you should buy a new one.

  • HT1338 I am trying to update Microsoft Office 12.3.3 on my Macbook Pro, but once it is installed terminal opens. What am I supposed to enter into Terminal?

    I am trying to update Microsoft Office 12.3.3 on my Macbook Pro, but once it is installed terminal opens. What am I supposed to enter into Terminal?

    Still trying to understand.  You install one of the MS updates (most recent was 14.2.2) and after the update completes (before the installer quits) terminal opens?  Or the installer quits and then terminal opens?
    And who is prompting for "Check for updates" ("get taken back" to what)?  Is this coming from office, say when you run Word?   Certianly the updater doesn't cause this prompt.

  • Just installing a few updates from the Mac App Store for mountain lion on my 2010 MacBook Pro, during this it made a noise and then the screen and keyboard went off, like it is off. What happened, is it off...or should I just wait it out?

    Just installing a few updates from the Mac App Store for mountain lion on my 2010 MacBook Pro, during this it made a noise and then the screen and keyboard went off, like it is off. What happened, is it off...or should I just wait it out?

    What kind of noise?
    The only things I can think of that make noise are fans and disks. Fans usually will not cause the computer to shutdown as you describe. My guess is your disk drive died. I hope you made a backup prior to start the ungrade.
    Allan

  • Some apps on my macbook pro will not open,,,they bouce a few times and disappear.  would someone please give me a straightforward answer on why this might be haappening(started after updates))   please?

    some apps on my macbook pro will not open,,,they bouce a few times and disappear.  would someone please give me a straightforward answer on why this might be haappening(started after updates))   please?

    Yay! Solved my own question; just did a hard shutdown, worked like a charm! Funny, didn't before. But who am I to question salvation?

  • I've just installed Mavericks on my Macbook Pro, which took forever to install, and everything appears to be fine except for iPhoto.  When I try and open iPhoto I get a popup saying its not supported by this OS.  Anyone have any ideas???   Help please.

    I've just installed Mavericks on my Macbook Pro, which took forever to install, and everything appears to be fine except for iPhoto.  When I try and open iPhoto I get a popup saying its not supported by this OS.  Anyone have any ideas???   Help please.

    Click App Store from your Apple menu  drop down menu then select Updates from the App Store menu bar.

  • Have Macbook Pro & 4th gen iPod Touch. Downloaded & installed iOS 4.3.2 yesterday. Upgrade went without a hitch, but now iTunes on My Macbook Pro will not open. I get an error that says "iTunes" Data too new to be used with this version of iTunes.

    Have a Macbook Pro and a 4th gen iPod Touch. Downloaded and install iOS 4.3.2 yesterday. Upgrade went without a hitch, but now iTunes on My Macbook Pro will not open. I get an error that says --The file "iTunes Library" cannot be read because it was created by a newer version of iTunes--. I am running iTunes 10.1.  I searched for Updates to my MacBook Pro (running 10.6.7), but comes back saying no updates available. WHAT IS GOING ON??

    Is your computer still authorized in the Store menu in iTunes?
    iTunes Store: About authorization and deauthorization
    When I changed to my new MacBookPro I had to authorize it although I used TimeMachine to transfer my settings and data.
    Did you try to deselect Wi-Fi syncing and enable it again after that?
    iTunes 10.5 and later: Troubleshooting iTunes Wi-Fi syncing
    Did you already transfer your purchases and manually started a backup?

  • HT201364 My 13 inch Macbook pro w retina will not install/download OS X Mavericks because it says I do not have the requirements in order to install it. I purchased my Mac this past month on 11/20/13 so i do not have a problem with it being an older versi

    My 13 inch Macbook pro w retina will not install/download OS X Mavericks because it says I do not have the requirements in order to install it. I purchased my Mac this past month on 11/20/13 so i do not have a problem with it being an older version. Please help. This is my first computer so i dont have any experience on how to fix this.

    You can't install the App Store version of Mavericks because your model needs a special version. If you ever need to reinstall it, boot into Recovery.

  • I have a MacBook Pro 15" 2.53GHz Mid2009.. updated to Lion which is now 10.7.3 build 11D50b... when I close lid and connect to Cinema Display, display will not activate... disconnect display, open lid laptop display will not activate... used to work fine.

    I have a MacBook Pro 15" 2.53GHz Mid2009.. updated to Lion which is now 10.7.3 build 11D50b... when I close lid and connect to Cinema Display, display will not activate when keyboard/mouse used... disconnect display, open lid and laptop display will not activate... only way out is hold power button.  Worked fine before Lion update.   Any Advice?

    Thanks very much Coander15... I've printed the doc you pointed me towards and I'll run through it.. hoping it helps!
    Before I installed Lion I simply hit any key on the keyboard or clicked the mouse...
    The keyboard is USB (usually connected to monitor which is connected to laptop... have tried direct connect to laptop as well with no luck) and mouse is USB wireless to one of those tiny plug in's... have tried direct connect USb mouse as well with no luck.
    I could plug the closed/sleeping laptop into the monitor and unplug from the monitor without incident all day/night... always worked fine. 
    Had heard something about this happening w/ Lion but went ahead anyway. 
    Oh well...
    Hoping your pointer helps... will let you know how it turns out.  Thanks very much for responding!!!

  • Keep downloading Firefox 6.0.2 for Mac (as prompted) to my new Macbook Pro, running Lion (OS 10.7.1) and it won't open and install. WTF?

    I have Firefox version 3.6.22 (Mac) & keep downloading Firefox 6.0.2 for Mac (as prompted) to my new Macbook Pro, running Lion (OS 10.7.1) and it won't open and install. WTF?

    something similar has been happening to me for a a couple weeks (even before the most recent update, but now is definitely worse) on my 2010 MacBook Air. Firefox freezes upon startup, and then freezes maybe every twenty minutes or so when I'm actively using it, staying frozen for at least a minute or two. it drives me crazy.

Maybe you are looking for

  • Read file, search file for duplicate addresses

    Hi - i have no teacher to ask, nor do i know any java programmers to ask this question, so your guidance would be appreciated. I have created an "Insurance Project " for myself� but I do not know how to proceed,I have a file that contains 30,000 reco

  • Satellie A100: How to use MMC card in card reader

    Hi everybody, first of all I have a Toshiba Satellie A100 Notebook. And now my question: at the front of the (closed) Notebook, there is card reader slot, right next to microphone and volume,etc. I have a MMC card of my mobile phone, but it doesn't f

  • Why does terminal behave differently with respect to "Resume" feature?

    Terminal behaves a little funky when it comes to the new "Resume" feature in Lion.  Here's a few interesting notes: When restarting, Terminal prompts the user to close itself.  If you don't click close in time, the reboot process is halted.  This ***

  • Help with DBMS_JOB

    Hello people, I studied the documentation and many websites about DBMS_JOB but I am still confused. How do I schedule a procedure to run i.e. every sunday 10:00 AM ? This is whta I tried: DECLARE   X NUMBER; BEGIN   SYS.DBMS_JOB.SUBMIT       job     

  • F1 help Information

    hi friends... in any field if i press F1 means i can get the program name... but in VA01 in condition tab-> table control line item... if i press F1 means.. i am getting  4 Frames 1. Screen Data 2. GUI Data 3. Field data 4. Field Description for Batc