Macbook Pro (2009) sleep issue

Hey all,
I normally have my 2009 Macbook Pro connected via HDMI to an external monitor, with display split between the two screens. However, recently, the manual sleep (command+option+eject) would begin to act like it was sleeping, including both screens turning black, but would then go to the login screen as if I had woken the computer. I tried a reset of the SMC which seemed to have fixed that problem. Was I correct in doing this?
I do have an additional problem that was not fixed by resetting the SMC. Again, when trying to sleep the computer, I would open the lid, login, and be presented with my desktop, but it would be all on my external monitor. The macbook screen would be black and it would be as if I were using the computer with the lid closed (which Lion allows). The only way to get the notebook screen back on is to unplug my external and plug it right back in. Any ideas?

Bump, please.

Similar Messages

17" MacBook Pro 2009 graphical issues

Hi Guys
I'm trying to figure out what's going on with my 17" Macbook Pro. It's a rather old model (2009) with the following specs:
i7 2.8 Ghz
16 GB ram
1TB SSD hard drive
I have Yosemite 10.10.1 installed on it. Lately, I've experienced a lot of graphical issues such as vertical shades when booting up, screen going black during usage (although it was still on), graphical glitches when booting or when using it, randomly rebooting, etc.
I hoped it to be a software issue so I did a clean install of Yosemite but the problem persists. Sometimes it boots just fine, sometimes it doesn't. As to the graphical issues and the vertical shades on screen, it also happens randomly.
Other things happen such as the coloured wheel coming out of nowhere for doing something as simple as clicking on a link within Safari... you name it, all sorts of glitches.
I decided to run a hardware test but then again, pressing D when it's booting is doing next to nothing (I've had issues re-installing Yosemite by pressing CMD + R too.. I had to try it a bunch of times before it actually worked).
I am now installing the beta version of 10.10.2 as I'm running out of options. Do any of these problems ring a bell ? Any suggestions ?
Thank you so much for your time.
Ricardo

It appears that your MBP has experienced kernel panics. If so log and post it per these instructions:
http://support.apple.com/en-us/HT201753
In order to run an Apple Hardware Test with your MBP you will have to use the #2 installation disk that came with your MBP. It has the AHT instructions printed on it. Note that an error free AHT is not definitive.
Ciao.

Macbook Pro SR sleep issues.

When I open the lid to wake my computer from sleep the screen is black, so I have to tap on the keyboard to get the login screen to come up. My old PB just wakes right up without hesitating. Is there a way to fix this. Sorry if this has already been answered. Thanks for your help.

If you open Terminal (in the Utilities folder) and type…
pmset -g
… and look at the "lidwake" field it should be set to 1. This means that it will wake when the lid is opened. However, if it's set to 0, which your behaviour suggests, then there's your problem. To set it to 0 you need to type…
sudo pmset -a lidwake 1
… and then type in your administrator password when asked.

I have a mid 2009 macbook pro and my issue is that I installed windows 7 and when I wan to install the drivers it says " bootcamp x64 is unsupported on this computer model" I tried installing the drivers with the bootcamp 4 but it did not work either

I have a mid 2009 macbook pro and my issue is that I installed windows 7 and when I wan to install the drivers it says " bootcamp x64 is unsupported on this computer model" I tried installing the drivers with the bootcamp 4 but it did not work either it says that i have a newer bootcamp version. I tried a few tricks but they didnot work. I hope to be helped

Welcome to Apple Support Communities
You can install a 64-bit Windows 7 or Vista version in your Mac. Make sure you downloaded these drivers > http://support.apple.com/kb/DL1630 Also, if you have the Snow Leopard DVD you used to upgrade your Mac or the OS X DVD that came with your Mac, you can use it to install the Boot Camp drivers

I have a Macbook Pro 2009, i upgraded from 10.5 to 10.8.2 and now when I put it to sleep it shuts down. Does anyone know how to fix this?

I have a Macbook Pro 2009, i upgraded from 10.5 to 10.8.2 and now when I put it to sleep it shuts down. Does anyone know how to fix this?

That disk from her computer is a machine specific version, you need this disk
http://store.apple.com/us/product/MC573Z/A
and follow these instructions
How to erase and install Snow Leopard 10.6

IPhotos and Photos both in Applications MacBook Pro 2009 13" But I cannot see Photos in iMovie

iPhotos and Photos both in Applications MacBook Pro 2009 13". I can see just iPhotos but I cannot see Photos in iMovie. Any advices for this issue? Thank you

It shut down and won't start again (harddrive clicking and sleep light blinking). I did SMC reset and it did not help

Apple 20" CD connects fine to MacBook Pro 2009 via DVI to Mini displayport (adapter) but not to Radeon 5770 (either MDP ports) on MacPro 2008?! Have Eizo CG223 on DVI to 5770. Any ideas?

Here's the setup:
Eizo Coloredge CG223 DVI to DVI on MacPro 5770 interface (ACD works fine on this too, naturally).
Apple Cinema Display 20" have the DVI connector. I have a Mini Displayport to DVI adapter on this, into one of the 5770's MDPs, neither of which seem to work.
Plug the same ACD via DVI (with DVI to MDP adpater) into my MacBook Pro 2009 MDP and it works fine as a second screen.
So what's up with the 5770 MDPs? I've seen online that the card should at least support two displays, either MDPs x2 or MDP and DVI. I've seen there may be an issue with three, not two.
Any ideas please?
Thanks,
Y

Striped down to bare inputs - monitors and keyboard/mouse. Works! Dimerising must have interfered with it. Phew!

Can I install only Windows on my Macbook Pro 2009?

Hello All,
For reasons far outwith my control. i.e. I am in the middle of borneo, needing desperatly to get on a full windows machine... I need answers to the following?
I have full gen versions of Windows 7 and MS Office 2010. I want to run these on my 13" MacBook Pro 2009. I know, boot camp, VMware etc are all great. But i can't at this time get those working.
I think, the best option is to just buy a HDD, remove the old one, install fresh copy (of win) onto new HHD.
However, my question is - will this work?
Thanks
Craig

As TheSmokeMonster indicated, you'll need to use either virtualization or BootCamp. BootCamp prepares your system to allow Windows to be installable on it (it also provides the drives for some of the hardware which may not be found elsewhere). Virtualization runs in OS X, so that should be a non-issue. Keep in mind, all firmware updates are only via OS X, so you would not be able to update your firmware unless you have a functioning bootable external OS X volume.
BootCamp does basically give you a full Windows machine... it just allows dual booting between Windows and OS X.

Is there a way to disable previously viewed iMessages from appearing as Messages notifications when waking my MacBook Pro from sleep?

Is there a way to disable previously viewed iMessages from appearing as Messages notifications when waking my MacBook Pro from sleep? Regardless of whether I am using iMessage from my iPhone or iPad, when I open my MBP, I get attacked by Messages notifications for iMessages I've obviously already seen or responded to. Is there a way to change this? Are others having this issue?
Additionally, previous iMessages sent or received from those devices sometimes don't populate into the Messages window on the MBP. I haven't been able to identify when or what causes this; sometimes it just doesn't seem to work (and I verified that the messages sent/received were, in fact, iMessages and not SMS).
Thanks - any help or insight would be appreciated!

First you need to determine what laptop model you have; then we can help you. A Mac Book Pro cannot run OS 9.1.
With your Mac booted up, click on the  at the far left of the menu. Then click on About This Mac. It will show what version of OS you are running. What is the version?
A MBP will be running something like version 10.x.
If you are running version OS 9.x, you don't have a Mac Book Pro.
 Cheers, Tom

I have a 13 inch MacBook Pro (2009) & the "White Screen of Death" is present. Need help?

I have a 13 inch MacBook Pro (2009). Recently I bought an extended hard drive because I had used up the memory on my iDisk. As I was running the Time Machine back up on my new extended drive, the battery on my Pro ran out causing it to shut down. Once I hooked up my Pro to the power cord & logged in, the "White Screen of Death" appeared on the home display. Obviously the battery still works, my phone is able to charge along with the extended drive, I am able to adjust the lighting on my keyboard along with adjusting the brightness on my screen, but the "White Screen" remains. I need help in determining the cause of this issue & the steps I'll need to take in order to resolve this. I love my Pro, all my documents, photos & music are on it & the last thing I want to do is kill my wallet by buying a new Pro. So could someone on here please help me? It would be greatly appreciated & I thank you in advance!

Take each of these steps that you haven't already tried. Stop when the problem is resolved.
Step 1
The first step in dealing with a boot failure is to secure your data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since your last backup, you can skip this step.
There are several ways to back up a Mac that is unable to boot. You need an external hard drive to hold the backup data.
a. Boot into the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.”
b. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, boot the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
c. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to boot, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can boot now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
If you've booted from an external storage device, make sure that your internal boot volume is selected in the Startup Disk pane of System Preferences.
Step 3
Boot in safe mode. Note: If FileVault is enabled, or if a firmware password is set, or if the boot volume is a software RAID, you can’t do this. Post for further instructions.
Safe mode is much slower to boot and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
When you boot in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, your boot volume is damaged and the drive is probably malfunctioning. In that case, go to step 5.
If you can boot and log in now, empty the Trash, and then open the Finder Info window on your boot volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then reboot as usual (i.e., not in safe mode.)
If the boot process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 4
Sometimes a boot failure can be resolved by resetting the NVRAM.
Step 5
Launch Disk Utility in Recovery mode (see Step 1.) Select your startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then reboot as usual.
Step 6
Reinstall the OS. If your Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Step 7
Repeat step 6, but this time erase the boot volume in Disk Utility before installing. The system should automatically reboot into the Setup Assistant. Follow the prompts to transfer your data from a Time Machine or other backup.
Step 8
This step applies only to a Mac Pro tower, not to any other model. A dead logic-board battery can cause a gray screen at boot. Typically the boot failure will be preceded by loss of the startup disk and system clock settings. See the user manual for replacement instructions.
Step 9
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store to have the machine tested.

Hi, I am using macbook pro 2009 model.In that, there is wifi hardware is not installed. I am not able to use wireless networks. Anybody can help me out.

Hello,
I am using Macbook pro 2009 model. In that, when I tried to connect wireless network and wifi. I am not able to do. I have done R & D regarding this issue. Some them advice to do some below steps.
Restart your Mac.
upon start-up, hold down the Opt key until you see your drives.
click on the recovery drive (note: this will not affect or delete any files you currently have).
login if needed.
in the top right hand corner you will see the Wi-Fi icon (hopefully). Click the icon and then click "turn wifi Off" and then again click "turn wifi ON"
restart your Mac again and start it up normally.
recover from your near-heart attack.
I've followed your 1 to 4 steps & then after clicking on the wifi icon, I found Wi-Fi: No hardware installed just beneath the icon. That means no Wifi hardware is installed in this machine. Do you have any suggestion about installing it? I mean how can I get that hardware? Is it available on internet? Thanks a lot again.

Apparently you have tried everything except - take the monitor in question to the Apple Store along with your computer. If it works there, the mystery continues.

MacBook Pro 2009 - Window 7 - Low Volume Output

I am experiencing low volume output on the internal speakers and slightly better volume on headphone output under BootCamp with Windows 7 x64 Ultimate. And of course the red light emitting diode is one constantly in the audio output jack.
I have seen fixes for the Windows XP folks over time and on my older MacBook (2006) with Vista x64, I found a fix. I have seen some thoughts on installing RealTek HD Audio drivers and that DID NOT work for Windows 7 x64 on my MacBook Pro 2009. I also tried reinstalling the CirrusAudio x64 from the BootCamp 3 drivers on my Snow Leopard DVD.
So I am left wondering if a driver update is forthcoming or if there is a fix that has been discovered and not reported online yet?

I'm going to leave this message for reference to other users...
As of October 22 2009 there is no known fix for the broken Cirrus Logic driver that comes with Bootcamp 3.0 under any 64bit Windows OS (including Windows 7 and Vista).
Apple seriously ***** for not doing anything about this for MONTHS and has lost a customer forever. I was going to get a 17in to complement my 13in MacBook Pro but this kind of driver issues is just plain unacceptable, and goes to show how you can't rely on a company like Apple for mission critical systems, period.
If they want to make ANY inroad in the corporate world the better get their stuff together and start delivering, the famous "excellent customer experience" for me is nowhere to be found. Lacking that, mac computers are only pretty although non-functional machines.
Sorry for the rant... I hope somebody from apple listens, but I doubt it.

Macbook Pro 2009 has gray screen, safe mode won't work

I have a Macbook Pro 2009, with a new hard drive installed in August of 2013. I opened my computer a couple days ago to a gray screen with a prohibitory sign and a spinning gear that will not disappear. I have no backup and tried to backup my hard drive to an external drive in Recovery Mode, but I got an error message and the backup did not work: the image could not be created. So I decided to try Safe Mode, but the Macbook will not enter safe mode. Is there any way to get onto the computer just to backup a handful of files onto an external drive before I format my drive and start over? Am I doing something wrong by trying to enter safe mode? (I held down the Shift key after the chime and released it when the Apple logo and the gear appeared) Any help is appreciated. I've read all the topics in the forums I could find on this issue, but none of the directions seem to help. Thank you.

LisaLoParo,
no, you’re not doing anything wrong in trying to boot into Safe mode.
I can think of three possible alternatives to Safe mode to try:
If you have an external disk, you could boot from the grey Mac OS X Install DVD which came in the box with your MacBook Pro, and try copying files from your internal disk to the external disk;
If you have a bootable external disk, you could boot from it using Startup Manager, and try copying files from your internal disk to the external disk;
If you have access to a FireWire 800 cable and a second Mac with a FireWire 800 port, you could try booting your MacBook Pro into Target Disk mode so that it can be used as an external disk from the second Mac, and try copying files from your MacBook Pro to the second Mac.
You’d only need to try one of these three alternatives; if you try one of them and it doesn’t work, then you’d get the same result by trying either of the other two. Good luck.

Bought a Macbook pro 2009 2.8 ghz used, how do I make the most? (it was not formatted)

bought a Macbook pro 2009 2.8 ghz used, how do I make the most? (it was not formatted)

The first thing to do with a second-hand computer is to erase the internal drive and install a clean copy of OS X. You—not the original owner—must do that. How you do it depends on the model, and on whether you already own another Mac. If you're not sure of the model, enter the serial number on this page. Then find the model on this page to see what OS version was originally installed.
It is not safe to use a computer with software installed by a previous owner.
1a. If you don't own another Mac
If the machine shipped with OS X 10.4 or 10.5, you need a boxed and shrink-wrapped retail Snow Leopard (OS X 10.6) installation disc from the Apple Store or a reputable reseller—not from eBay or anything of the kind. If the machine has less than 1 GB of memory, you'll need to add more in order to install 10.6. Preferably, install as much memory as it can take, according to the technical specifications.
If the machine shipped with OS X 10.6, you need the installation media that came with it: gray installation discs, or a USB flash drive for some MacBook Air models. For early MBA models, you may need a USB optical drive or Remote Disc. You should have received the media from the original owner, but if you didn't, order replacements from Apple. A retail disc, or the gray discs from another model, will not work.
To start up from an optical disc or a flash drive, insert it, then restart the computer and hold down the C key at the startup chime. Release the key when you see the gray Apple logo on the screen.
If the machine shipped with OS X 10.7 or later, you don't need media. It should start up in Internet Recovery mode when you hold down the key combination option-command-R at the startup chime. Release the keys when you see a spinning globe.
Some models shipped with OS X 10.6 and received a firmware update after 10.7 was released, enabling them to use Internet Recovery. If you have one of those models, you may not be able to reinstall 10.6 even from the original discs, and Internet Recovery may not work either without the original owner's Apple ID. In that case, contact Apple Support, or take the machine to an Apple Store or another authorized service provider to have the OS installed.
1b. If you do own another Mac
If you already own another Mac that was upgraded in the App Store to the version of OS X that you want to install, and if the new Mac is compatible with it, then you can install it. Use Recovery Disk Assistant to prepare a USB device, then start up the new Mac from it by holding down the C key at the startup chime. Alternatively, if you have a Time Machine backup of OS X 10.7.3 or later on an external hard drive (not a Time Capsule or other network device), you can start from that by holding down the option key and selecting it from the row of icons that appears. Note that if your other Mac was never upgraded in the App Store, you can't use this method.
2. Partition and install OS X
If you see a lock screen when trying to start up from installation media or in Recovery mode, then a firmware password was set by the previous owner, or the machine was remotely locked via iCloud. You'll either have to contact the owner or take the machine to an Apple Store or another service provider to be unlocked. You may be asked for proof of ownership.
Launch Disk Utility and select the icon of the internal drive—not any of the volume icons nested beneath it. In thePartition tab, select the default options: a GUID partition table with one data volume in Mac OS Extended (Journaled) format. This operation will permanently remove all existing data on the drive.
After partitioning, quit Disk Utility and run the OS X Installer. If you're installing a version of OS X acquired from the App Store, you will need the Apple ID and password that you used. When the installation is done, the system will automatically restart into the Setup Assistant, which will prompt you to transfer the data from another Mac, its backups, or from a Windows computer. If you have any data to transfer, this is usually the best time to do it.
Then run Software Update and install all available system updates from Apple. To upgrade to a major version of OS X newer than 10.6, get it from the Mac App Store. Note that you can't keep an upgraded version that was installed by the original owner. He or she can't legally transfer it to you, and without the Apple ID you won't be able to update it in Software Update or reinstall, if that becomes necessary. The same goes for any App Store products that the previous owner installed—you have to repurchase them.
3. Other issues
If the original owner "accepted" the bundled iLife applications (iPhoto, iMovie, and Garage Band) in the App Store so that he or she could update them, then they're irrevocably linked to that Apple ID and you won't be able to download them without buying them. Reportedly, Mac App Store Customer Service has sometimes issued redemption codes for these apps to second owners who asked.
If the previous owner didn't deauthorize the computer in the iTunes Store under his Apple ID, you wont be able to authorize it immediately under your ID. In that case, you'll either have to wait up to 90 days or contact iTunes Support.
When trying to create a new iCloud account, you might get a failure message: "Account limit reached." Apple imposes a lifetime limit of three iCloud account setups per device. Erasing the device does not reset the limit. You can still use an account that was created on another device, but you won't be able to create a new one. Contact iCloud Support for more information.

Browsing Youtube and Macbook Pro (2009) froze--rebooting just leads to apple logo against grey screen and loading circle

I was browsing Youtube when the entire Macbook Pro (2009) froze up. After a couple of minutes, I forced a shut down and now when I try starting it back up it just displays the apple logo against the grey backdrop with the loading circle just going around and around.
I have no idea what's going on with it. I tried disconnecting it from the power cord--letting it cool down, took the battery out, etc...

That's called a Gray Screen issue and it could be caused by multiple factors.
You can run through the Steps here to narrow it down
https://discussions.apple.com/docs/DOC-3353

Macbook Pro (2009) sleep issue

Similar Messages

Maybe you are looking for