MacBook Pro 2012 hinge problem with single click sound when i open it

when i go to sleep and shut my macbook off and close the screen next morning i open my screen and i hear a single click noise??
im paranoid ita a brand new macbook its not a hard drive fail it just a single click sound when i open it to turn on
and heres a video of the hinge is this is whats causing the single click sound? http://www.youtube.com/watch?v=wEUt2p783nA

I have this problem too with my Mid-2012 MBP non-retina. The screen would click once, after being left for a long time, and would be fine after that, until you close it and re-open it again after a long time. It is especially loud in the morning so I think it is temperature dependent. Happened about 3 months after buying. I took it to Apple. First time they replaced the entire screen. They had to since that is the only way to replace the hinge. When I got it back, the screen still clicks. Took it back to Apple again. Second time they just tightened the screws securing the display with the unibody. When I got it back the second time, the screen still clicks. Took it back to Apple again. The third time they replaced the entire screen AGAIN! When I got it back, the problem was fixed for 2 days, then the screen started clicking again so I'm back to square one. I'm wondering whether I should take it to Apple the forth time, but then again, they've already replaced the screen twice which didn't work so I'm not sure what more they can do. It's either this is normal, which implies the screen hinge is really badly designed or the clicking has nothing to do with the screen at all.

Similar Messages

MacBook pro 2012 hinge problem? help!!

here is a video explaing it all (its not my video a found a video with someone having the same problem as me)
http://www.youtube.com/watch?v=Ta6ra8nk4XU
PLEASE HELP WHAT IS THIS? WHAT IS CAUSING IT? WHAT CAUSED IT?
im going to apple tomorrow to get it checked out i jus wana know ^ (the questions)

I have this problem too with my Mid-2012 MBP non-retina. The screen would click once, after being left for a long time, and would be fine after that, until you close it and re-open it again after a long time. It is especially loud in the morning so I think it is temperature dependent. Happened about 3 months after buying. I took it to Apple. First time they replaced the entire screen. They had to since that is the only way to replace the hinge. When I got it back, the screen still clicks. Took it back to Apple again. Second time they just tightened the screws securing the display with the unibody. When I got it back the second time, the screen still clicks. Took it back to Apple again. The third time they replaced the entire screen AGAIN! When I got it back, the problem was fixed for 2 days, then the screen started clicking again so I'm back to square one. I'm wondering whether I should take it to Apple the forth time, but then again, they've already replaced the screen twice which didn't work so I'm not sure what more they can do. It's either this is normal, which implies the screen hinge is really badly designed or the clicking has nothing to do with the screen at all.

Macbook pro 2012 bluetooth problem with magic mouse

I have a MacBook Pro 2.6 GHz Intel Core i7 running Mac OS X 10.7.4
It's two days old and Bluetooth has stopped working.. I use bluetooth for my apple magic mouse.
I know it's the Bluetooth app and not the mouse as I changed the mouse batteries and double checked it with my old iMac.
The Bluetooth app has become sluggish and unresponsive.
I have restarted and logged out and in.
Run permissions.
Switched Bluetooth off and on.
Scratched my beard.
Any ideas or similar problems?

Not sure which Bluetooth app you are referring to ...
Try deleting Bluetooth preferences ...
Open the Finder. From the Finder menu bar click Go > Go to Folder
Type this exactly as you see it here:
/LIbrary/Preferences
Click Go
Move the com.apple.Bluetooth.plist file from the Preferences folder to the Trash.
Now open System Preferences > Bluetooth and try re "pairing" the mouse.

I installed indesign CS5 on new macbook pro and keeps freezing with spinning wheel once the app opens. Is there an issue with OS Mav or font issue or a plist I can pull. All other Adobe products work.

I installed indesign CS5 on new macbook pro and keeps freezing with spinning wheel once the app opens. Is there an issue with OS Mav or font issue or a plist I can pull. All other Adobe products work.

Migration should never be done with any Adobe program.
If you have done Migration, you have to UNINSTALL first (if even possible) and then download Adobe Creative Cloud Cleaner Tool and run that also. When this is done, restart your computer and install the programs from an original Adobe Installer.
Other question is, if your OS is supporting that version. You can try it, it is not officially supported, but it might work.
But CC will work, upgrade to CC2014 (without additional cost), use that as it is better anyway.

I got my iPhone 4S and I think I have a problem with it. Sound when locking and unlocking is quiet compared with other iPhone 4S. I compared it with others and really is a little quiet. Other people have confirmed it too. Other sounds may be better. No pr

I got my iPhone 4S and I think I have a problem with it. Sound when locking and unlocking is quiet compared with other iPhone 4S. I compared it with others and really is a little quiet. Other people have confirmed it too. Other sounds may be better. No problem tones, watching videos. This problem or is it something normal?

I have this problem too, but it is intermittent. Sometimes the lock/unlock volume will drop to barely-audible, even though in settings the volume slider hasn't changed. If I then move the volume slider, it fixes the problem and the lock sounds jump back to normal, but then later on the problem will happen again.

Why Does Retina MacBook Pro (2012) Suddenly Hibernate With Lid Open?

I'd like to know why my Retina MacBook Pro (2012) at certain times suddenly go into Hibernate mode when I'm actively using it with the lid open and what I can do to prevent this.
I know this is hibernate because of what I see in the Console logs and the fact that I can't trigger a wake by using the keyboard/trackpad/mouse. Only the power button causes it to wake up.
This usually happens when I wake it from sleep and plug it into an external monitor via HDMI to HDMI connection.   The lid is open and I use both displays.    This happens about 30 seconds to a minute after I wake from sleep. At the time I'm not plugged into the power supply because I believe it's generally a good idea to let the batter drain and the recharge it. The last time this happened it was about 35% to 40% charged.
Hardware Overview:
Model Name:    MacBook Pro
Model Identifier:    MacBookPro10,1
Processor Name:    Intel Core i7
Processor Speed:    2.6 GHz
Number of Processors:    1
Total Number of Cores:    4
L2 Cache (per Core):    256 KB
L3 Cache:    6 MB
Memory:    8 GB
Software:
OS X Yosemite (all latest updates installed)
{some 3rd party software}
Let me know if you need more information.
For the gory details of what I see in system.log, read on:
This is about the time the hibernate happens. I've replaced my laptop's name with {COMPUTER NAME}
Mar 20 18:29:26 {COMPUTER NAME} identityservicesd[375]: <IMMacNotificationCenterManager: 0x7f87d510c9e0>: notification observer: com.apple.iChat   notification: __CFNotification 0x7f87d5210a90 {name = _NSDoNotDisturbEnabledNotification}
Mar 20 18:29:26 {COMPUTER NAME} identityservicesd[375]: <IMMacNotificationCenterManager: 0x7f87d510c9e0>:    NC Disabled: NO
Mar 20 18:29:26 {COMPUTER NAME} identityservicesd[375]: <IMMacNotificationCenterManager: 0x7f87d510c9e0>:   DND Enabled: YES
Mar 20 18:29:26 {COMPUTER NAME} identityservicesd[375]: <IMMacNotificationCenterManager: 0x7f87d510c9e0>: Updating enabled: NO   (Topics: (null))
Mar 20 18:29:26 {COMPUTER NAME} WindowServer[218]: device_generate_desktop_screenshot: authw 0x7fba81c2e940(2000), shield 0x7fba81c35bd0(2001)
Mar 20 18:29:27 --- last message repeated 1 time ---
Mar 20 18:29:27 {COMPUTER NAME} WindowServer[218]: device_generate_lock_screen_screenshot: authw 0x7fba81c2e940(2000)[0, 0, 1920, 1080] shield 0x7fba81c35bd0(2001), dev [1920,1080]
Mar 20 18:29:27 {COMPUTER NAME} com.apple.xpc.launchd[1] (com.apple.xpc.launchd.domain.user.502): Service "com.apple.xpc.launchd.unmanaged.loginwindow.72" tried to hijack endpoint "com.apple.tsm.uiserver" from owner: com.apple.SystemUIServer.agent
Mar 20 18:29:30 --- last message repeated 1 time ---
Mar 20 18:29:30 {COMPUTER NAME} kernel[0]: PM response took 4741 ms (30, powerd)
Mar 20 18:29:30 {COMPUTER NAME} kernel[0]: ARPT: 1632.007298: AirPort_Brcm43xx::powerChange: System Sleep
Mar 20 18:29:30 {COMPUTER NAME} kernel[0]: ARPT: 1632.007302: wl0: powerChange: *** BONJOUR/MDNS OFFLOADS ARE NOT RUNNING.
Mar 20 18:29:30 {COMPUTER NAME} kernel[0]: [0x1b014fb000, 0x19000000]
Mar 20 18:29:30 {COMPUTER NAME} kernel[0]: [0xd8ec7000, 0x19000000]
Mar 20 18:29:30 {COMPUTER NAME} kernel[0]: [0x1369ac0000, 0xe000000]
Mar 20 18:29:30 {COMPUTER NAME} kernel[0]: [0x0, 0x0]
Mar 20 18:29:31 {COMPUTER NAME} kernel[0]: hibernate image path: /var/vm/sleepimage
And when I wake it up by repeatedly pressing the power button:
Mar 20 18:30:09 {COMPUTER NAME} kernel[0]: hibernate_newruntime_map time: 0 ms, IOHibernatePollerOpen(), ml_get_interrupts_enabled 0
Mar 20 18:30:09 {COMPUTER NAME} kernel[0]: IOHibernatePollerOpen(0) 19 ms
Mar 20 18:30:09 {COMPUTER NAME} kernel[0]: hibernate_machine_init reading
Mar 20 18:30:09 {COMPUTER NAME} kernel[0]: PMStats: Hibernate read took 355 ms
Mar 20 18:30:09 {COMPUTER NAME} kernel[0]: hibernate_machine_init pagesDone 212628 sum2 2c66736a, time: 355 ms, disk(0x20000) 447 Mb/s, comp bytes: 57749504 time: 55 ms 985 Mb/s, crypt bytes: 157388800 time: 67 ms 2228 Mb/s
Mar 20 18:30:09 {COMPUTER NAME} kernel[0]: Wake reason: EC.PowerButton (User)
Mar 20 18:30:09 {COMPUTER NAME} kernel[0]: vm_compressor_fastwake_warmup (7450 - 12878) - starting
Mar 20 18:30:09 {COMPUTER NAME} kernel[0]: Previous sleep cause: -60
Mar 20 18:30:09 {COMPUTER NAME} kernel[0]: Previous shutdown cause: 5
Mar 20 18:30:09 {COMPUTER NAME} kernel[0]: AppleThunderboltNHIType2::prePCIWake - power up complete - took 0 us

This happened again at about 31% power, again unplugged.   Previously, I had plugged in the power before pressing the power button, but this time I pressed the power button before plugging in. The display showed me the out of power icon. Only on plugging it back in was I able to power up the laptop again.
Is it possible there's a bug either with the displayed power or how remaining power is detected?

MacBook Pro (2012) running slow with loud fan?

My 2012 MacBook Pro has all of a sudden being running very slow while running the fan really loudly even though the computer is not hot? I have done the SMC reset, and checked the disk for any problems and both have not changed anything. I have checked the activity monitor and it says 433 GB free and my CPU seems to low in all applications as far as I can understand. I am out of the country so I cannot bring it into an Apple store so I'd appreciate help that I can do myself! Thanks.

First, back up all data immediately, as your boot drive might be failing.
There are a few other possible causes of generalized slow performance that you can rule out easily.
Reset the System Management Controller.
If you have many image or video files on the Desktop with preview icons, move them to another folder.
If applicable, uncheck all boxes in the iCloud preference pane.
Disconnect all non-essential wired peripherals and remove aftermarket expansion cards, if any.
Check your keychains in Keychain Access for excessively duplicated items.
Otherwise, take the steps below when you notice the slowdown.
Step 1
Launch the Activity Monitor application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Activity Monitor in the icon grid.
Select the CPU tab of the Activity Monitor window.
Select All Processes from the menu in the toolbar, if not already selected.
Click the heading of the % CPU column in the process table to sort the entries by CPU usage. You may have to click it twice to get the highest value at the top. What is it, and what is the process? Also post the values for % User, % System, and % Idle at the bottom of the window.
Select the System Memory tab. What values are shown in the bottom part of the window for Page outs and Swap used?
Next, select the Disk Activity tab. Post the approximate values shown for Reads in/sec and Writes out/sec (not Reads in and Writes out.)
Step 2
If you have more than one user account, you must be logged in as an administrator to carry out this step.
Launch the Console application in the same way you launched Activity Monitor. Make sure the title of the Console window is All Messages. If it isn't, select All Messages from the SYSTEM LOG QUERIES menu on the left. If you don't see that menu, select
View ▹ Show Log List
from the menu bar.
Select the 50 or so most recent entries in the log. Copy them to the Clipboard (command-C). Paste into a reply to this message (command-V). You're looking for entries at the end of the log, not at the beginning.
When posting a log extract, be selective. Don't post more than is requested.
Please do not indiscriminately dump thousands of lines from the log into this discussion.
Important: Some personal information, such as your name, may appear in the log. Anonymize before posting. That should be easy to do if your extract is not too long.

MacBook Pro 11/2007 problem with SSD OCZ Vertex Series 250 GB

Hi,
you can read my detailed problem in the OCZ board here:
http://www.ocztechnologyforum.com/forum/showthread.php?t=64941
The short version:
- I bought an OCZ Vertex SSD with 250 GB for my 2 years old MacBook Pro
- System Details: MacBookPro3,1; Boot Rom: MBP31.0070.B07; CPU: Intel Core 2 Duo 2.4GHz; SMC: 1.18f5
- The first 250 GB OCZ SSD was an firmware 1.3 and I could install it with Snow Leopard very easy. After 2 days the HDD just disappeared and it also didn't work in an other PC with an internal SATA port and also not with an external disk with sata to FireWire / USB
- I RMA'ed the disk with OCZ and received a new one with firmware 1.4. I tried to install the computer from scratch and it couldn't write the partition when the SSD was connected to the internal SATA port of the MBP. I used the external SATA to USB and formated the disk with another mac. Then I could install SL from scratch but after some hours the computer began to stall and after the reboot it tried to run fschk and I got the error: "kernel[0]: disk0: I/O error."
(again: Further details please have a look at the link above)
- When I boot the system through firewire with the SSD connected through SATA to Firewire it works like a charm but that doesn't make sense (Having a MBP with an external boot drive)
- I RMA'ed the disk again and last week I received the third one but it had the exact same problem.
So now OCZ told me to ask apple for a possible solution. Does anybody have an idea what to do?
I've read two posts about OCZ problems and they wrote about efi 1.7 problem and with efi 1.6 it would work. Didn't try it out yet - should I?
Thanks for you help!
--Goetz aka Tankmann

No ideas?

I have new macbook pro 2012, after reimage with mountain lion new version image its locked by firmware password(i have the password but the password not accepted) and its just freeze at apple icon and doesnt boot to OSx, how to make it working?

macbook pro seem not working, not either go to startup screen just freeze on apple icon.
and cannot also password for firmware are wrong when i type it in.
how can i know the keyboard problem if the password are confirm right?

Use the trackpad to scroll, thats what it was designed for. The scroll bars automatically disappear when not being used and will appear if you scroll up or down using the trackpad.
This is a user-to-user forum and most people will post on here if they have problems. You very rarely get people posting to say there update went smooth. The fact is the vast majority of Mountain Lion users will not be experiencing any major problems with the OS, or maybe with apps which are not compatible, but thats hardly Apple's fault if developers don't update their apps.

My macbook pro is having problems with external hardrive installation

I bought a seagate 2TB external hard drive and every time that I get to the part of the installation where it asks me to "activate" this product my computer tells me "not responding". I called seagate tech support and they told me that I have something wrong with my operating system. My macbook pro is still OS 10.4 version, so it's time to upgrade, which is what I'm trying to do by backing up all of my files before I install snow leapard, but I'm getting stuck at this seemingly simple step of activation. Is there any ideas of where to go from here?

What sort of activation is this? Sounds like something you really don't need unless the drive is somehow locked.
I think I would do the following:
Drive Preparation
1. Open Disk Utility in your Utilities folder. If you need to reformat your startup volume, then you must boot from your OS X Installer Disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu.
2. After DU loads select your hard drive (this is the entry with the mfgr.'s ID and size) from the left side list. Note the SMART status of the drive in DU's status area. If it does not say "Verified" then the drive is failing or has failed and will need replacing. SMART info will not be reported on external drives. Otherwise, click on the Partition tab in the DU main window.
3. Under the Volume Scheme heading set the number of partitions from the drop down menu to one. Set the format type to Mac OS Extended (Journaled.) Click on the Options button, set the partition scheme to GUID (for Intel Macs) or APM (for PPC Macs) then click on the OK button. Click on the Partition button and wait until the process has completed.
4. Select the volume you just created (this is the sub-entry under the drive entry) from the left side list. Click on the Erase tab in the DU main window.
5. Set the format type to Mac OS Extended (Journaled.) Click on the Options button, check the button for Zero Data and click on OK to return to the Erase window.
6. Click on the Erase button. The format process can take up to several hours depending upon the drive size.

I just got my macbook pro 11 have problems with setting up audio interfaces!! plz help me

So here it goes! i properly installed the drivers for my Emu tracker pre usb and for my saffire pro 40 (firewire) . Both audio interfaces show up in the system profiler under their respective category (firewire and usb bus) But i cant get them to apear in system preferences sound menu neither on logic!! my saffire pro doesnt even lock with the mix control software provided! what can be the problem ? how can i solve it ? I really need your help!!
(everything works perfect on my i mac 27" 10.6.2 snow leopard).

I doubt you will have any virus, must never say never
Free for Home use
Sophos
http://www.sophos.com/en-us/products/free-tools/sophos-antivirus-for-mac-home-ed ition.aspx
also free from app store Clam XAV
http://www.usatoday.com/story/tech/columnist/komando/2013/02/14/tech-myths-mac-s oftware-megapixels-camera/1910521/
Your Battery will not last long if you keep it on full brightness.
see this read
https://discussions.apple.com/thread/964075?start=0&tstart=0
http://support.apple.com/kb/PH3738
http://support.apple.com/kb/index?page=search&src=support_site.home.search&local e=en_US&q=Battery%2095%25
Open LaunchPad/Other/Activity Monitor/CPU
and check if any of your processes are high% CPU if so select it and press the Red Quit process Button
Mac101 may assist you
http://www.apple.com/support/macbasics/

Macbook Pro late 2013 - problem with login screen resolution

Hi,
I've got problem with login screen resolution, after upgrade to Yosemite. I use the 4rd resolution (last one) on my Mac Pro (late 2013), and after restart login screen is always on optimum mode... But it's only about the login screen.
Do you know how can I fix it? I would like to have the same resolution on every screen.
thx in advance

I Reformatted the CF card on the new computer   it works fine now on the new Mac Pro
Interesting point about the low power of the usb ports   I had to deal with all devices ejecting them selves when the mac pro was idle or slept Drobo needed a Firmware update and another drives needed me to change the sleep setting or the Mac Pro   to never and i also had to deploy a script to write to each device ever minute,   this kind of sold the problem with external Hard drives.   I wonder if the lowering power to a CF card   can eject it in a manor which would make the computer think it is corrupt.
I have looked at buying a power usb Hub    but seems only one or two of the ports are powered.
Seems to be a bit problem with the mac pro especially as everything has to be connected externally
Will assume the Firewire Connector does not work.

My laptop macbook pro has a problem with usb port they are not working.

hi there i have a late 2011 mac pro, its been 2 years of purhase however reary used, now it has a problem with usb port are drawing too much power and usb ports are dissabled from the system. now i can not use usb ports. do yo have solution for it??? cheers

Reset SMC. http://support.apple.com/kb/HT3964
Choose the method for:
"Resetting SMC on portables with a battery you should not remove on your own".
Best.

Macbook Pro won't boot up makes clicking sound

Hi.
After upgrading to Firefox 4 on my 15inch 2006 Macbook Pro, it froze for over 5 minutes and began to make an odd repeated clicking sound. I tried force-quitting, but that wouldn't work, so I restarted it. Now it won't even boot up fully, it just makes a similar odd clicking sound (but not as frequently).
However, the grey Apple screen does appear, along with the revolving wheel. It seems very odd though, as the light at the front of the machine goes out as soon as the machine attempts to restart, which suggests that something physical may have occured to some internal hardware.
I even tried booting up in Safe Mode, but it is no different. Also, Caps lock and Number lock keys both appear to be working, so hopefully the keyboard is still functional.
Does anyone have any ideas what may have happened. My Applecare expired about two years ago, so really need some assistance if possible.
Thanks
George

First try booting from your OS X installer DVD. If the computer boots into the installer then do this:
Repair the Hard Drive and Permissions
After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer.
If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
After returning to the installer reinstall Snow Leopard. This will not erase the drive. Reinstalling takes from 45 minutes to an hour or so.

I have a serious issue with static (clicking sounds) when I use Netflix streaming along with any movies I rent via AppleTV, and yes I use a optical audio cord. Any suggestions?

Was is most interesting, is that if I watch other content like MLB TV using the sound bar and optical cable, I don't have this issue, it's all very strange. Any suggestions?

Perhaps it's obvious to you, but what would I adjust in the midi settings? There's nothing obvious that speaks to this out of sync issue.
FYI, I just plugged my JBL creatures into the audio out (same physical jack as the digital out, though of course they use different technologies) and there is no sync problem with the audio played through them. Clearly it's an issue with the digital out, just wish I could figure out if it's my stereo or something in the computer. I have no other devices that accept a digital input, so can't swap the stereo out for anything else.

MacBook Pro 2012 hinge problem with single click sound when i open it

Similar Messages

Maybe you are looking for