Macbook Pro and USB HUB
Let me start with this. My Macbook Pro (4 yrs old) has only 2 usb ports, so I went to buy a USB HUB. I bought Pentagram HUB USB 4P Passive [P 1224-3] , I plug it in. Small green light on it is on. Then I plug the printer, wireless mouse receiver and a WD Passport 160GB. None of the above are working. (The printer has it's own power cable). Where's the problem. Is it the HUB or something else?
Please help.
It's the hub. "Passive" is the key to your problem.
An "active" or "powered" hub prevents devices from drawing more power than the ports can deliver. Your big consumer is the WD passport drive. You're powering not only the electronics but also an electric motor.
If you mainly need the hub for working in a home or office environment, always go for the powered type. The passive hub may work for travel as long as you limit the number of devices.
Similar Messages
-
How to format my macbook pro and I dont have my lion cd or usb stick?
How to format my macbook pro and I dont have my lion cd or usb stick?
try this
http://support.apple.com/kb/HT3294http://support.apple.com/kb/HT3294
http://support.apple.com/kb/TS4265http://support.apple.com/kb/TS4265
If you don't have the original PSWD, your beat, so tough if your a kid trying to be a kid -
i have an ipod touch 3rd gen this is my second ipod touch my fist one the battery died after 4 years so then a bought this one (ipod touch 3gen) and it works perfectlybut for some time know it wont charge anywhere else thats not my macbook pro and the thing is the only charges and its recognized only on one of the USB porst of the laptop i have a windows 7 computer but it wont charge there have a linux (ubuntu) machine and doesnt work either, the wall charger with the same cable i use on the laptop and wont charge either i plug it on my sisters car and wont charge my char wont charge anyways i wont charge anywhere else thats not my macbook pro only with 1 of the 2 USB pork that the MBP has..... any help? can someone ewlp me? i really doubt its the battery cause it charges fine on my MBP :/.... oh now i recently upgrade to OSX Lioin but the problem perssist I did the recent update but the problem persists :/
- See:
iPod touch: Hardware troubleshooting
- Try another cable. Some 5G iPods were shipped with Lightning cable that were either initially defective or failed after short use.
- Try another charging source
- Inspect the dock connector on the iPod for bent or missing contacts, foreign material, corroded contacts, broken, missing or cracked plastic.
- Make an appointment at the Genius Bar of an Apple store.
Apple Retail Store - Genius Bar -
i plugged in my ipod and now i get the error message: Because a USB device was drawing too much power from your computer, one or more of your USB devices have been disabled" - i have a MAcBook pro and now my USB ports do not work - can anyone help me ???
Sometimes you have to reset the SMC two or three times for it to work, don't know why. I've seen that error message before and 100% of the time it was fixed with an SMC reset. I suppose it's possible that your keyboard or mouse IS drawing too much power, do you have access to another you could try?
-
I have taken my 750GB HD out of my 17" MacBook Pro and put it into a 2.5" USB to SATA enclosure but can't get it to open up on my new 11" MacBook Air. Any ideas please.
Have you installed the recent update?
There are some issues with Apple USB 3.0 ports and some devices. -
How can I get Time Machine to back up an external hard drive (iPhotos) that is attached to airport extreme base station. Note: Time machine is usb to macbook pro and external drive with iphotos is usb to airport extreme base station. Help please. Thanks!
Once you have the drive connected to your Mac, click System Preferences (gear icon) on the dock
Click Time Machine
Click Options
Be default, the hard drive will be Excluded from backups. Click the drive to highlight it, then click the "-" (minus) button at the bottom of the list to remove the drive from Excluded items.
The drive will be backed up on the next Time Machine pass
Everything above assumes that the hard drive has been formatted in Mac OS Extended (Journaled) as Time Machine will only backup drives in that format. -
I have my new HD in a USB enclosure connected to my MacBook Pro and I want to put a fresh copy of Mountain Lion on it. I'm told that I need to boot from the Installation Disk to start. But I do not have an install DVD as I got ML as a download from the App Store. Can I download ML from the App Store again, but this time directly to my new HD?
Create a data recovery/undelete external boot drive
You can also use Carbon Copy Cloner to clone your present setup to it and boot from it.
Most commonly used backup methods
However, SOME external enclosures are not bootable, you will soon find out. -
Can Macbook Pros (and Macbooks) boot off of USB drives?
I know that you cannot boot off of USB drives in iMacs, but is that the case for Macbook Pros and Macbooks too? I have Ubuntu installed on a 16 GB usb drive and was wondering if it is possible to boot to that usb drive. I cannot simple Boot camp or just dual boot my own way because it is a school computer that they lend me for the year.
I know that you cannot boot off of USB drives in iMacs
That's only the case for some PowerPC Macs. It doesn't apply to any Intel Mac, including MacBooks and MacBook Pros.
(55569) -
i plugged a usb in to my macbook pro and rhe computer went off and wont turn back on. the power light doesnt light. what do i do??? help!
Do you have Apple Care? Is there an Apple Store near you?
Sounds like a hardware fault... -
I plugged my IPhone 4S into the usb on my MacBook Pro and I sent a text message on my phone, my MacBook shutdown and won't re-start
Have a read here...
https://discussions.apple.com/message/18409815?ac_cid=ha
And See Here...
How to Use Multiple iDevices with One Computer -
hello,i have a macbook pro and i just recently downloaded facetime, and now i cant use it, it says An internal FaceTime error occurred,i dont know how to fix it, please help.
If your webcam is powered by USB, make sure it is attached directly to your Mac and not a USB hub. In my case, I had my Rocketfish webcam attached to a peripheral USB hub and it wasn't drawing enough power to operate at capacity. Therefore, Facetime was quitting on me and giving me that exact error message. Once I attached the webcam directly to my Mac USB port, problem solved. Hope that helps.
-
Officejet Pro 8600 - Macbook Pro and Macbook Air will not print
Products:
HP Officejet Pro 8600
Macbook Pro (Mac OS X, Version 10.7.5)
Macbook Air (OS X, Version 10.8.2)
Question:
Why did my Macs initially print fine, but now will not print at all?
Full Story:
I have a wireless network at my house that consisted of a 30mb cable internet, Netgear 900n, HP Officejet Pro 8600, 2 Dell Laptops with Windows 7, a Lenovo Laptop with Windows 7, and Dell Tower with Windows 7 - All printed just fine.
The HP Officejet 8600 was added to my network about 2 months ago.
I added a Macbook Pro and a Macbook Air about 3 weeks ago. Both Macs printed just fine for about a week. Then suddenly they stopped. I spent about 2 hours on the phone with HP Service, and they finally said it must be my router. So I called Netgear. Netgear was useless! They wanted me to agree to charges for services before they would even discuss the issue.
Due to information provided by HP's service support, and because Netgear will not support their product, I promptly purchased a new router - an Apple Airport Extreme.
The Macs recognize the printer, will print if hardwired via a USB cable, but will not print wirelessly to the Officejet Pro 8600. The PCs print fine.
The frustration that is being felt is compound by the fact that the Macs printed just fine with the Officejet Pro 8600 2 weeks ago, and now the printer just shows "idle"... even with a new router. (see image below)
Please help, I appreciate any support.
As a side note, the HP Service rep was very friendly, and definitely tried to support the HP Product, which is much more than I can say about Netgear.
Thank you,
This question was solved.
View Solution.Hi,
More likely the issue related with Multicast, which Apple devices relies on to communicate with teh device through the network.
First try unplugging the router for 30 seconds.
Plug it back to the power and wait for 2-3 minutes.
Turn the HP printer Off and back On, then check for any difference.
If the same persists, try changing your router configuration as following
Note: the settings below are not related with the HP product, I provide you the steps as a best effor and those are only based on my own knowledge. you may try modifying the router settings at your own risk:
Open the router configuration page (can be found listed as the Default Gateway by clicking the Wireless icon on the printer, then print a network configuration report.
Click the Advanced tab.
Click the Setup option from the menu, then click on WAN Setup.
Make sure to uncheck the box next to Disable IGMP Proxying and Apply the changes.
Click the LAN Setup on the same Setup menu.
Set the RIP Version as RIP-2 and Apply the changes.
Reboot your router and then check for any change.
I hope you may find that information useful, you may also use the user guide below for further information:
http://www.downloads.netgear.com/files/GDC/WNDR4500/WNDR4500_UM_07DEC2011.pdf
Shlomi
Say thanks by clicking the Kudos thumb up in the post.
If my post resolve your problem please mark it as an Accepted Solution -
(Trouble printing) Trouble with connection between Macbook Pro and Hp Deskjet 1510.
Trouble with connection between Macbook Pro and Hp Deskjet 1510. (Nothing Prints).
I have a Macbook Pro and am having difficulty printing documents from ‘Pages' from my Hp Deskjet 1510. I have installed the necessary software for the printer and it is connected via USB. Every time I try to print the printer icon comes up as it should, 'printing' and then 'job completed' and then the icon disappears. (Nothing is printed.) I thought it might be something to do with Pages compatibility with the printer but exporting the document to Word or making it a PDF doesn’t change anything. I don’t have Microsoft Word on my computer. The scanner does work and when I printed a ‘Test Page’ that worked too.
Let me know if you know why this is happening.With these settings the network now works flawlessly, however, when i have my ethernet cable plugged in, my internet access via my airport card(on the macbook pro) is no longer available. Hoping you can tell me why this would be with this info i've provided.
Educated guess. The networking devices have priorities as to which are used. The standard order is that Ethernet has a higher priority than Airport.
While your Ethernet is unplugged it is inactive and the Mac ignores it. Once you plug it in, the Mac sees that it is active and switches traffic to that interface.
I actually take advantage of this feature at home, but configuring my Airport and Ethernet with identical fixed IP addresses. Normally I'll use Airport, but if I'm copying a huge file and I want faster performance, I'll just walk my MacBook (previously iBook, previously Powerbook) over to my Ethernet switch and plug in my MacBook. Magically, the Mac detects that the Ethernet is active and continues the file transfer uninterrupted over the faster 100baseT Ethernet connection. When the transfer is finished, or if I really need to move back to the Comfy Chair, I unplug the Ethernet cable, and all activity reverts back to the Airport, all without disrupting any existing networking connections.
You on the other hand have totally different settings for your Ethernet and your Airport, so when you switch to Ethernet, you basically loose your Airport connections.
Something you can try:
System Preferences -> Network
Gear icon on the bottom left, next to the [+] [-] icons.
Select *Set Service Order...*
Now Drag the network interfaces into the perfer priority order you want. In this case put Airport above Ethernet.
NOTE: You may want to create a new Network Location for this, instead of messing with your normal home Location (which is most likely the default Automatic. That way you have your original you can always fall back to. -
In my macbook pro hdmi, usb & SD card reader not working
In my macbook pro hdmi, usb & sc card reader not working.
i have tried the SRM reset done, till not working started.
Could you please resolve this problem,Welcome to Apple Support Communities
Simply take it to an Apple Store or reseller if it's in warranty. Your Mac will be repaired or replaced for free because it looks a hardware problem rather than a software issue.
If it's not in warranty, hold Command and R keys while your MacBook is starting up, and reinstall OS X. If it doesn't work, you can't do much more to solve the problem -
I have a macbook pro and use BT homehub 3. can't work out how to connect my time capsule. can anyone help? thanks
Just need to plug the TC in to the hub in bridge mode.. do not try and bridge the homehub.. it is not possible with the setup BT uses.
To bridge the TC.. plug it directly into a computer by ethernet.. no other connection to the TC or the computer.
Press and hold in reset until the front LED flashes rapidly.. about 10sec.
Release the reset.
Open the airport utility and setup the TC to bridge mode.
The actual method depends on version of the OS and airport utility you use.
This is version 5.
Sorry I cannot post the v6 as I am on a snow leopard computer now. But you go to the network tab, and choose off bridge mode for method of connection. It will be NAT and dhcp by default.
Then setup wireless.. you have a number of choices here.
Either setup with the same SSID Security and password, as the homehub uses.. or a different name, and password..
Each method works fine.. but you sometimes have issues with wireless channels.. for now leave it on auto and see what happens.. if you have issues lock down the radio channels on both devices.. use one out of the following on each, 1, 6, 11 or 13 in UK.. so say 6 on the homehub then 13 onthe TC.
Update the TC.. unplug fromt the computer and plug it into the homehub.
If you have other issues with the setup tell us what OS you run so we can post suitable screenshots.
Maybe you are looking for
-
ActiveX to open and close application
I am new to LV (have 6.1). What I want to do is open up an external application when a certain LV action is performed (like a boolean button, or something similar), minimize the LV application (will use Application Builder here), and close it when a
-
How to recover my picture organisation in iPhoto 09
After having invested plenty of time in organising my new iphoto 09 I have unexpectedly lost all my events, faces and places. I am now at the starting point. Is tehre any way to recover them. Thanks for the assistance
-
Windows xp says 10.2 is installed, but you tube says still I need to install it ???
could not do auto download http://get.adobe.com/flashplayer/download/?installer=Flash_Player_10.2_for_Windows_Interne t_Explorer&p=Google_Toolbar_6.5&a=McAfee_Security_Scan_Plus&os=XP&browser=ie&type=activex ... never got information bar (activex rem
-
My iTunes says there is a new version and is giving me the choice to download or not. I keep choosing to download it but it opens up the box to update my Apple software and Mobile Me. I never can update my iTunes. I'm sure it's available because t
-
I cannot get any photos into Photo Stream
I have a MacBook Pro late 2011 updated to Mountain lion, an iPad 2 and the latest Apple TV. I have followed the instructions on all devices to the letter and followed the help instructions in the Apple Support Section, but I cannot get a single phot