MacBook pro bought in 2010 when u turn it on screen is gray with apple logo and spinning wheel and won't turn on???
When trying to turn on MacBook pro bought in 2010 (Mac OS X) I get a gray screen with an apple logo and a spinning wheel. Won't go any further. Any ideas? I have photos I haven't saved and don't want to loose them.
stevesurplus wrote:
and a few other suggested solutions and they have not worked?
What are the 'other suggested solutions'?
Ciao.
Similar Messages
-
I bought my macbook pro this morning. When I turned it on it led me through set up with voice over. I finally quit VO but my pointer is not working. It moves but does not open anything. Can anyone help?
ladislavfromcygnet wrote:
Thank you Shootist007. I cannot do even Update now. I probably should have spent the same amount of money on a new IMac!
No not really. If this is a brand new Macbook Pro take it back for a refund. Apple has a 14 day No Questions Asked return policy for Full refund.
Take it back, get the Full Refund (DO NOT LET THEM TRY TO FIX IT. YOU BOUGHT A NEW COMPUTER NOT ONE THAT HAS BEEN WORKED ON OR NEEDS TO BE FIXED) and then decide whether to buy another Macbook Pro or the iMac. Or you could return it, get the Full refund and buy some other brand computer. -
MacBook Pro doesnt start. When I start my lap top, it shows the apple and the line uploading but it only goes like to 1/3 and then it goes blank for some seconds, then it turns off by itself and turn on again and happen the same, apple logo, line .. the noise like-fan going on, then turn off and turn on again. Tried starting holding option command P and R key and didnt work either. Starting to think I have lost all my data inside
Try a SMC reset.
http://support.apple.com/kb/ht3964
It might be helpful if you indicated the exact model/year of your MBP. Are you running Lion OSX?
Ciao. -
When turning on my mac book pro it displays a screen with apple logo and begins loading a loading bar, after this continues to show loading circle however has been like this all day still no different. Tried turning it on and off however still same!
... then run Disk Utility, Repair Disk.
Also:
Resolve startup issues and perform disk maintenance with Disk ...
Mac troubleshooting FAQ: start-up woes
How To Fix Common Mac Startup Problems
Mac Stalls on Gray Screen at Startup - Troubleshooting Mac Startup ... -
I have snow leopard installed as an OS. When trying to reboot a MacBook Pro I am getting stuck on grey screen with apple logo and rotating symbol. What can I do?
Maybe this might help.
http://support.apple.com/kb/TS2570 -
Macbook Pro (2011) froze while working, forced shut down, now won't turn on. Grey screen with apple logo and spinning wheel for hours. Help?
Unfortunately do not know the operating system since I never updated anything and I can't get in to it.
Thanks for your assistance.If you want to preserve the data on the boot drive, and it's not already backed up, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data, you can skip this step.
There are several ways to back up a Mac that is not fully functional. You need an external hard drive to hold the backup data.
1. Boot from the Recovery partition or from a local Time Machine backup volume (option key at startup.) Launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.”
2. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, boot the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
3. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data. -
Cannot get iPad 2 charged beyond 1%. All charging ports tried: AC adapter(s), USB 2 port on MacBook Pro. ITunes shows iPad only for a few seconds. iPad displays alternately: Apple logo, battery w/slim red band, then battery w/1% charged information. How can I get it to charge beyond 1% so I can proceed to troubleshoot?
I have had your exact problem with my old 3GS, now I cannot even get it to turn on, I still see that it is supposed to be charging though, but it never charges any so it seems.
I replaced the Lower Dock Connector Assembly back when it still charged while hooked to my PC, and it found it made no real difference.
http://www.amazon.com/gp/product/B003Y5YXLK/ref=oh_details_o05_s00_i00?ie=UTF8&p sc=1
At this point I am not sure if I should replace the battery and hope for the best, or just junk the phone, I cannot really sell it if I cannot reset it... -
My MacBook Pro is stuck on grey loading screen with apple logo and spinning wheel.
PLEASE HELP - Tried to start up my MacBook Pro and I get grey screen w/ apple logo & spinning wheel. It's stuck on this screen. Safe mode didn't help but reveled this: smc read key action error, BOOS key failed, BOPS key failed. Consider rebuild of prelinked kernal com.apple.kext triggers triggered rebuild. IOBluetooth host controller USB transport Suspend Device. I ran verifications/repairs in Disk Utilities, but nothing came back wrong on the reports. I'm a bit panicked, as I use this computer for work and have no other computer to use in the meantime. I should also note that I have very little technical knowledge, so if you can lend your help please keep that in mind when responding. I'd be over the moon if anyone can help.
Startup - Gray, Blue or White screen at boot, w/spinner/progress bar
Startup - Gray Screen
Startup Issues - Resolve
Startup Issues - Resolve (2) -
So yeah...last night I was checking out my iPod (bored at the in-laws) and all of a sudden the screen went blank and the only thing I can get it to do is have the black screen w/ the white apple logo on it. It won't turn on, doesn't give the the option to power down, it won't charge, AND it's NOT being recognized when I plug it into my computer. Not by iTunes OR my computer. I've tried holding down the top button and the home button at the same time...nothing. And since it's not being recognized on my computer, I cannot restart it or go back to factory settings. Someone please help! I've had it for 18 months so the warranty is no longer valid and I don't know how to fix it. THANK YOU in advance!
- I would try placing the iPod in recovery mode and then see if iTunes will see the iPod. try both with the iPod not connected to the computer and with it connect. For recovery mode see:
iPhone and iPod touch: Unable to update or restore
- Next see if placing the the iPod in DFU mode will make it visible
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings -
I'm transfering info from my old pc to my new macbook pro, using Windows Migration Assistant. All was fine but has now lost connection (wifi) and won't reconnect. Mac is showing transfer window and I cant escape, I'm new to mac
You'll need to erase the drive by booting up holding command-option-r keys into your Recovery Volume.
Use Disk Utility to erase the disk and then Internet Recovery. That will take a while.
http://support.apple.com/kb/HT4718 -
i bought iphone 5s 2 days ago and suddenly it turn off and start again till the white screen with apple logo and start again
please answer me as soon as possibleHello Ahmedabokamar,
Thanks for the question! I'd recommend taking a look at the following article for troubleshooting steps that can help get your iPhone working again.
iOS: Not responding or does not turn on
http://support.apple.com/kb/TS3281
Cheers,
Allen -
When I update the ios on my Iphone 4 it wont turn on and I tried to restore it, but it stuck in restore with apple logo and loading bar not move at all, I contact apple support and they tried to help me but nothing work, then they told me to send it to replace it and I need to pay $149, that's mean if anybody has any problem with his iphone even the problem from apple software you need to pay, that's not fair at all.... I will try to sale all our apple device and by Samsung device to resolve this problems.
I believe this means that it is bricked, just sell it for parts, to someone like me
-
Hi my serial number on bottom of my mac is W8******66E when l try to turn the computer on it is just going to grey screen with apple logo and spinning wheel i have tried starting in safe mode and a few other suggested solutions and they have not worked?
<Edited by Host>What other solutions have you tried?
This may help you:
https://discussions.apple.com/docs/DOC-3353
Ciao. -
Won't turn on white screen with apple logo and spinning disc
Mac book air won't boot up just has a white screen with apple logo and spinning disc have tried all the startup multiple key pushes , I think
Take each of these steps that you haven't already tried. Stop when the problem is resolved.
Step 1
The first step in dealing with a boot failure is to secure your data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since your last backup, you can skip this step.
There are several ways to back up a Mac that is unable to boot. You need an external hard drive to hold the backup data.
a. Boot into the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.”
b. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, boot the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
c. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
If the startup process stops at a blank gray screen with no Apple logo or spinning "daisy wheel," then the startup volume may be full. If you had previously seen warnings of low disk space, this is almost certainly the case. The easiest way to deal with the problem is to boot from an external drive, or else to use either of the techniques in Steps 1b and 1c to mount the internal drive and delete some files. According to Apple documentation, you need at least 9 GB of available space on the startup volume (as shown in the Finder Info window) for normal operation.
Step 3
Sometimes a boot failure can be resolved by resetting the NVRAM.
Step 4
If you use a wireless keyboard, trackpad, or mouse, replace or recharge the batteries. The battery level shown in the Bluetooth menu item may not be accurate.
Step 5
If there's a built-in optical drive, a disc may be stuck in it. Follow these instructions to eject it.
Step 6
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to boot, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can boot now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
Step 7
If you've booted from an external storage device, make sure that your internal boot volume is selected in the Startup Disk pane of System Preferences.
Boot in safe mode. Note: If FileVault is enabled, or if a firmware password is set, or if the boot volume is a software RAID, you can’t do this. Post for further instructions.
Safe mode is much slower to boot and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
When you boot in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, your boot volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 6.
If you can boot and log in now, empty the Trash, and then open the Finder Info window on your boot volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then reboot as usual (i.e., not in safe mode.)
If the boot process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 8
Launch Disk Utility in Recovery mode (see Step 1.) Select your startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then reboot as usual.
Step 9
Reinstall the OS. If your Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Step 10
Repeat Step 9, but this time erase the boot volume in Disk Utility before installing. The system should automatically reboot into the Setup Assistant. Follow the prompts to transfer your data from a Time Machine or other backup.
Step 11
This step applies only to models that have a logic-board ("PRAM") battery: all Mac Pro's and some others (not current models.) Both desktop and portable Macs used to have such a battery. The logic-board battery, if there is one, is separate from the main battery of a portable. A dead logic-board battery can cause a boot failure. Typically the failure will be preceded by loss of the settings for the startup disk and system clock. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
Step 12
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store, or go to another authorized service provider. -
when i restored my iphone 5 it shows 4013 and 4005 error and my phone was stuck with apple logo and above some letters where also there in black and white colour . pls say me how to fix this plssss . my email = **********
<E-mail Edited by Host>Wrong Forum
Maybe you are looking for
-
I noticed that Firefox updates instantly the places.sqlite database on disk, with every new page load. I suppose this is done to maintain the History complete in the event of a crash. The same thing happens with the permissions.sqlite and formhistory
-
Pop up view in Web Dynpro for ABAP
Hi, I am new in web dynpro for ABAP. Now I am facing a problem of how to make a view pop up. Since I had already create some table in this view. I just want to make it pop up after I click a button. But I had no idea to do it, could anyone tell me ho
-
Hello everyone. I need some help with a problem we are having with our application. It consists on Servlets, JMS with MDBs, Xml parsing... Our application dequeues messages from an Oracle Queue and sends xml-text message to a servlet. It also receive
-
Email button appears after specific action?
HI, I have a form where it needs multiple signatures - is there anyway that when the last signature is applied that an email button appears on the form to send it to the department that needs the form? Thanks Jodi
-
Inserting a photo into an existing slide show
I have tried to do this on my own but without success. The photo is located in both Events and Photos. I have iPhoto '11 Version 9.4.3. I am on the iMac OSX Mountain Lion 10.8.5. Appreciate assistance. Thank you!