Macbook Pro doesn't go into sleep mode when battery dies. Help Please!

When ever my Macbook Pro gets low on battery power I receive the "battery is low message" and instead of just going to sleep a couple minutes later it just shuts down completely. Any reason for this?? I want it to go to sleep like it used to when the battery gets low/dead.
here is my battery info!
Battery Information:
Model Information:
Manufacturer: SMP
Device name: ASMB012
Pack Lot Code: 0002
PCB Lot Code: 0000
Firmware Version: 0102
Hardware Revision: 0500
Cell Revision: 0200
Charge Information:
Charge remaining (mAh): 1526
Fully charged: No
Charging: Yes
Full charge capacity (mAh): 4557
Health Information:
Cycle count: 345
Condition: Normal
Battery Installed: Yes
Amperage (mA): 1583
Voltage (mV): 12083
System Power Settings:
AC Power:
System Sleep Timer (Minutes): 90
Disk Sleep Timer (Minutes): 10
Display Sleep Timer (Minutes): 60
Automatic Restart On Power Loss: No
Wake On AC Change: No
Wake On Clamshell Open: Yes
Wake On LAN: No
Current Power Source: Yes
Display Sleep Uses Dim: Yes
Battery Power:
System Sleep Timer (Minutes): 10
Disk Sleep Timer (Minutes): 10
Display Sleep Timer (Minutes): 2
Wake On AC Change: No
Wake On Clamshell Open: Yes
Display Sleep Uses Dim: Yes
Reduce Brightness: Yes
Thanks for any help!!

Same exact issue on my MacBook Pro. It is brand a brand new model: MacBook Pro (June 2009), with Mac OS X 10.6.1 and "7 hour battery".
Model Information:
Manufacturer: SMP
Device name: bq20z451
Pack Lot Code: 0000
PCB Lot Code: 0000
Firmware Version: 0003
Hardware Revision: 0003
Cell Revision: 0100
Charge Information:
Charge remaining (mAh): 6515
Fully charged: Yes
Charging: No
Full charge capacity (mAh): 6690
Health Information:
Cycle count: 27
Condition: Normal
Battery Installed: Yes
Amperage (mA): -936
Voltage (mV): 12311
System Power Settings:
AC Power:
System Sleep Timer (Minutes): 10
Disk Sleep Timer (Minutes): 10
Display Sleep Timer (Minutes): 10
Wake On AC Change: No
Wake On Clamshell Open: Yes
Wake On LAN: No
Display Sleep Uses Dim: Yes
GPUSwitch: 2
Battery Power:
System Sleep Timer (Minutes): 10
Disk Sleep Timer (Minutes): 10
Display Sleep Timer (Minutes): 2
Wake On AC Change: No
Wake On Clamshell Open: Yes
Current Power Source: Yes
Display Sleep Uses Dim: Yes
GPUSwitch: 2
Reduce Brightness: Yes

Similar Messages

  • MacBook Pro doesn't go into sleep mode after connecting Thunderbolt display

    Hi,
    after connecting a Thunderbolt display to the 2011 MacBook Pro 13", the system doesn't stay in sleep mode.
    When pressing cmd.alt.eject it goes into sleep for 1 or 2 seconds and then goes back on.
    everything works fine otherwise and the MacBook goes to sleep without problems if the Thunderbolt display is not attached.
    Any suggestions?
    Thanks in advance,
    Jordi

    I found the problem.
    It turns out that it has nothing to do with the Thunderbolt Display, but with Bluetooth and the Magic Trackpad.
    When I installed the TD, I also added a wireless keyboard and Magic Trackpad that I had been using with another system.
    If the option to allow the system to wake up by Bluetooth devices is enabled (system preferences, Bluetooth, advanced), the MacBook Pro will go to sleep and immediately wake up.
    Simply disabled that option and everything works fine.
    Now I need to open the lid of the MBP to wake up the system. Kind of a huge power button :-)
    Thanks for your help!
    Jordi

  • IPad doesn't go into sleep mode when guided access is enabled

    My iPad doesn't go into sleep mode when guided access is enabled despite having set "enable sleep mode" to on in the settings menu.  COnsequently, my battery life drains very quickly during the day as the screen doesn't dim or go into sleep mode at all.  Help!

    Seems this feature is lost with iOS 7.0.4.  I just bought 4 iPod Touches for employee use and NEED to have sleep mode enabled for guided access to conserve battery life.
    I did have 1 iPod that allowed me to enable sleep mode (and I tested that it allowed the top button to be pressed to immediately go to sleep), then after it ran the 7.0.4 upgrade it no longer allowed sleep mode when in guided access (I did not check the original version of iOS on the iPod but it was obviously older than 7.0.4).
    Is there some new hidden way to turn this on or did Apple delete the option?

  • HP AIO 8610 Pro doesn't go into sleep mode anymore

    I noticed yesterday that theAIO  panel stays lit now, with sleep mode activated.   When before, in sleep mode, the panel darkens.   I reset sleep mode to 10 minutes from 5 minutes only to determine if this will allow for sleep. I also restarted the AIO8610 to recycle anything that may be stopping 'sleep'. Please advise.

    Hi , I see you have been troubleshooting an issue with the sleep mode not darkening the display screen on the Officejet Pro 8610, and I think I may have some information for you. Is the printer connected directly to a wall outlet or is it in a surge protector or a power bar? We want to connect it to a wall outlet just so we can eliminate the power source as the root cause. If it is currently connected to a wall outlet you may want to try a different one in another room. See this document for more information about Issues when Connected to an Uninterruptible Power Supply/Power Strip/Surge Protector (Note: This document is not limited to Laserjet printers.) When you reset the printer did you do a full hard reset;Leave the printer on and unplug the power cable from the back of the printerWhile it is unplugged, you can hold down the power button on the printer for about 10-15 seconds to release any built up powerThen plug the printer back in To confirm, you are changing the sleep mode settings as per the manual instructions?To change the time to Sleep mode:1. From the printer control panel display, touch (ECO).2. Touch Sleep, and then touch the desired option. NOTE: If you change your country or region from the printer control panel, the time to sleep mode is automatically set to the default, which is 5 minutes. Maybe re-selecting your country or region will set the printer back to the defaults. To try this;Locate your Setup menu
    You should see an option for Printer SetupThen touch on Country/Region, re-select your country and region Other then these steps, I would check for firmware updates that may also correct the problem you are experiencing. You can click on this link to Getting Printer Updates for HP Officejet Pro 8610 Series. A couple of other documents that have information related to sleep mode;What is Sleep Mode?The Printer Stops Responding after Entering Sleep Mode or Power Save Mode If the issue continues, please Contact HP Support for further assistance. Fill in the model number and the form to receive a case number for quicker assistance.  Please let me know if these steps resolved your issue, or if there is anything else I can do to help.  I look forward to hearing from you!  Thanks, 

  • IOS 4 on 3G - Phone doesn't go into sleep mode when on a call

    I have a 3G iphone with the 4.0 OS. Whenever I get or make a phone call the screen does not go black therefore causing me to hit mute buttons and what not. I didn't have this problem on my 2g phone. I've tried to research it and look it up in the settings and I come up with nothing. How can I get this problem fixed ?

    Same exact issue on my MacBook Pro. It is brand a brand new model: MacBook Pro (June 2009), with Mac OS X 10.6.1 and "7 hour battery".
    Model Information:
    Manufacturer: SMP
    Device name: bq20z451
    Pack Lot Code: 0000
    PCB Lot Code: 0000
    Firmware Version: 0003
    Hardware Revision: 0003
    Cell Revision: 0100
    Charge Information:
    Charge remaining (mAh): 6515
    Fully charged: Yes
    Charging: No
    Full charge capacity (mAh): 6690
    Health Information:
    Cycle count: 27
    Condition: Normal
    Battery Installed: Yes
    Amperage (mA): -936
    Voltage (mV): 12311
    System Power Settings:
    AC Power:
    System Sleep Timer (Minutes): 10
    Disk Sleep Timer (Minutes): 10
    Display Sleep Timer (Minutes): 10
    Wake On AC Change: No
    Wake On Clamshell Open: Yes
    Wake On LAN: No
    Display Sleep Uses Dim: Yes
    GPUSwitch: 2
    Battery Power:
    System Sleep Timer (Minutes): 10
    Disk Sleep Timer (Minutes): 10
    Display Sleep Timer (Minutes): 2
    Wake On AC Change: No
    Wake On Clamshell Open: Yes
    Current Power Source: Yes
    Display Sleep Uses Dim: Yes
    GPUSwitch: 2
    Reduce Brightness: Yes

  • IPad doesn't go into sleep mode

    I have an iPad 2 3G, and it doesn't go into sleep mode when I'm pressing Power button, also it doesn't work through the AssistiveTouch.
    I would appreciate any help. Thanks from Sweden:)

    Hello Quentin,
    It might be worth attempting a restart of the iPad, and then a reset, should restarting fail to resolve the issue.
    iPhone, iPad, iPod touch: Turning off and on (restarting) and resetting
    http://support.apple.com/kb/HT1430
    If the iPad still won't sleep, I would recommend restoring the device.
    iTunes: Restoring iOS software
    http://support.apple.com/kb/HT1414
    All the best,
    Allen

  • MacBook doesn't turns into sleep mode and swop doesn't work.

    MacBook doesn't turns into sleep mode and swop doesn't work.
    Can you help me please. I have a MacBook Pro 8.2. I reinstalled OS X to make swop file working, but it still doesn't work. I reinstalled OS X from Internet recovery.
    Start time: 10:31:02 03/15/15
    Model Identifier: MacBookPro8,2
    System Version: OS X 10.10.2 (14C109)
    Kernel Version: Darwin 14.1.0
    Time since boot: 3 minutes
    Memory
        BANK 0/DIMM0:
          Size: 4 GB
          Speed: 1333 MHz
          Status: OK
          Manufacturer: 0x029E
        BANK 1/DIMM0:
          Size: 4 GB
          Speed: 1333 MHz
          Status: OK
          Manufacturer: 0x029E
    SerialATA
       TOSHIBA MK5065GSXF                     
    Diagnostic reports
       2015-03-15 Boom 2 crash
       2015-03-15 com.apple.internetaccounts crash
    Log
       Mar 15 10:26:10 memorystatus_thread: idle exiting pid 546 [tccd]
       Mar 15 10:26:11 memorystatus_thread: idle exiting pid 547 [nsurlstoraged]
       Mar 15 10:26:12 memorystatus_thread: idle exiting pid 544 [soagent]
       Mar 15 10:26:13 memorystatus_thread: idle exiting pid 548 [nsurlstoraged]
       Mar 15 10:26:43 memorystatus_thread: idle exiting pid 556 [com.apple.CodeSi]
       Mar 15 10:26:44 memorystatus_thread: idle exiting pid 558 [accountsd]
       Mar 15 10:26:45 memorystatus_thread: idle exiting pid 553 [com.apple.iCloud]
       Mar 15 10:26:46 memorystatus_thread: idle exiting pid 561 [networkd_privile]
       Mar 15 10:26:47 memorystatus_thread: idle exiting pid 555 [secinitd]
       Mar 15 10:26:48 memorystatus_thread: idle exiting pid 560 [tccd]
       Mar 15 10:26:49 memorystatus_thread: idle exiting pid 562 [secd]
       Mar 15 10:26:50 memorystatus_thread: idle exiting pid 554 [com.apple.intern]
       Mar 15 10:26:51 memorystatus_thread: idle exiting pid 565 [nsurlstoraged]
       Mar 15 10:26:52 memorystatus_thread: idle exiting pid 563 [soagent]
       Mar 15 10:26:53 memorystatus_thread: idle exiting pid 551 [syncdefaultsd]
       Mar 15 10:26:54 memorystatus_thread: idle exiting pid 557 [CoreServicesUIAg]
       Mar 15 10:26:55 memorystatus_thread: idle exiting pid 567 [iconservicesd]
       Mar 15 10:26:56 memorystatus_thread: idle exiting pid 566 [iconservicesagen]
       Mar 15 10:26:57 memorystatus_thread: idle exiting pid 568 [systemstatsd]
       Mar 15 10:26:58 memorystatus_thread: idle exiting pid 550 [cfprefsd]
       Mar 15 10:26:59 memorystatus_thread: idle exiting pid 552 [cfprefsd]
       Mar 15 10:27:00 memorystatus_thread: idle exiting pid 549 [coreduetd]
       Mar 15 10:27:01 memorystatus_thread: idle exiting pid 564 [nsurlstoraged]
       Mar 15 10:28:18 ** GPU Hardware VM is disabled (multispace: disabled, page table updates with DMA: disabled)
       Mar 15 10:29:09 proc 316: load code signature error 4 for file "Boom 2"
    I/O per process: coresymbolicati (UID 0) is using 15 MB/s
    kexts
       com.globaldelight.driver.Boom2Device (1.1)
    Daemons
       com.apple.installer.osmessagetracing
    Agents
       com.apple.AirPortBaseStationAgent
       com.globaldelight.Boom2Daemon
    Extensions
       /Library/Extensions/Boom2Device.kext
       - com.globaldelight.driver.Boom2Device
       /System/Library/Extensions/EPSONUSBPrintClass.kext
       - com.epson.print.kext.USBPrintClass
       /System/Library/Extensions/JMicronATA.kext
       - com.jmicron.JMicronATA
    Applications
       /Applications/Boom 2.app
       - com.globaldelight.Boom2
       /Applications/Boom 2.app/Contents/Library/LoginItems/Boom2Daemon.app
       - null
    Bundles
       /Library/Printers/Canon/BJPrinter/Plugins/BJNP/CIJNetworkIOM.plugin
       - jp.co.Canon.ij.print.iom.CIJNP
       /Library/Printers/Canon/BJPrinter/Plugins/BJNP/CIJNetworkPBM.plugin
       - jp.co.Canon.ij.print.pbm.CIJNP
       /Library/Printers/Canon/BJPrinter/Plugins/BJUSB/BJUSBIOM.plugin
       - jp.co.canon.bj.print.bjusbiom
       /Library/Printers/Canon/BJPrinter/Plugins/BJUSB/BJUSBPBM.plugin
       - jp.co.canon.bj.print.pbm.USB
       /Library/Printers/Canon/BJPrinter/Plugins/BJUSB/CIJUSBClassDriver.plugin
       - jp.co.canon.ij.print.CIJUSBClassDriver
       /Library/Printers/Canon/BJPrinter/Plugins/BJUSB/CIJUSBClassDriver2.plugin
       - jp.co.canon.ij.print.CIJUSBClassDriver2
       /Library/Printers/Canon/BJPrinter/Plugins/IJBluetooth/IJBluetoothIOM.plugin
       - jp.co.canon.ij.print.ijbluetoothiom
       /Library/Printers/EPSON/CIOSupport/CIOHelper.plugin
       - com.epson.print.plugin.CIOHelper
       /Library/Printers/EPSON/CIOSupport/EPSONUSBPrintClass.plugin
       - com.epson.print.plugin.USBPrintClass
       /Library/Printers/EPSON/CIOSupport/XIOP.plugin
       - com.epson.print.plugin.XIOP
       /Library/Printers/EPSON/CIOSupport/XIORemoteClient.plugin
       - com.epson.print.plugin.XIORemoteClient
       /Library/Printers/EPSON/CIOSupport/XIORemoteServer.plugin
       - com.epson.print.plugin.XIORemoteServer
    Restricted files: 219
    Elapsed time (s): 238

    Remove "Boom" and test.
    Any third-party software that doesn't install by drag-and-drop into the Applications folder, and uninstall by drag-and-drop to the Trash, is a system modification.
    Whenever you remove system modifications, they must be removed completely, and the only way to do that is to use the uninstallation tool, if any, provided by the developers, or to follow their instructions. If the software has been incompletely removed, you may have to re-download or even reinstall it in order to finish the job.
    I never install system modifications myself, and except as stated in this comment, I don't know how to uninstall them. You'll have to do your own research to find that information.
    Here are some general guidelines to get you started. Suppose you want to remove something called “BrickMyMac” (a hypothetical example.) First, consult the product's Help menu, if there is one, for instructions. Finding none there, look on the developer's website, say www.brickmymac.com. (That may not be the actual name of the site; if necessary, search the Web for the product name.) If you don’t find anything on the website or in your search, contact the developer. While you're waiting for a response, download BrickMyMac.dmg and open it. There may be an application in there such as “Uninstall BrickMyMac.” If not, open “BrickMyMac.pkg” and look for an Uninstall button. The uninstaller might also be accessed by clicking the Customize button, if there is one.
    Back up all data before making any changes.
    You will generally have to restart the computer in order to complete an uninstallation. Until you do that, there may be no effect, or unpredictable effects.
    If you can’t remove software in any other way, you’ll have to erase and install OS X. Never install any third-party software unless you're sure you know how to uninstall it; otherwise you may create problems that are very hard to solve.
    Trying to remove complex system modifications by hunting for files by name often will not work and may make the problem worse. The same goes for "utilities" such as "AppCleaner" and the like that purport to remove software.

  • My new macbook pro retina randomly goes into standby mode

    My new macbook pro retina randomly goes into standby mode. I have to close the screen and wait a few seconds and re-open it in order for it to come back on.
    Sometimes it immediately goes back into standby mode again after closing and reopening the screen. I have checked the battery level everytime, and it has never been below 40% when this occurs. Is this a Mountain Lion issue?

    Well I fixed my problem.
    I took it into the Apple store. Even without the other two monitors they were able to recreate the problem. One symptom (I had) was that one of the Hot Corners was set to Disable screen saver. If you then put your cursor there, you'd go into screen saver mode. Change the setting to another corner and the problem follows you there.
    The Apple person at the Genius bar logged out as me and back in as test and same problem. He tried some stuff and finally said I needed to wipe the drive and reinstall the OS (Lion). I'd only had the machine for 12 hours and had just migrated my data to it, so I didn't mind doing that. I did it at home.
    Problem solved.
    BUT... then I reinstalled the driver for my EVGA UV Plus 19 (most current drivers) and bingo problem back. Uninstall. Problem gone. I'm now using mini display port to DVI for one monitor and HDMI for the other I think the machine is a bit warmer this way (versus using a USB to the EVGA device) but at least it's not sleeping all the time. Someone might say "it (the heat) is your imagination" or something else. Or someone might say "use the other thunderbolt port for another mini-display port to DVI" but I need that for the LAN... c'est la vie.
    Maybe I'll write to evga and see what they say. Maybe they'll fix their driver and/or Apple will fix it.

  • My MacBook Pro doesn't start; in safe mode shift CMD V the message "disk0s2: media is not present" is written on the screen repeatedly but the MacBook doesn't start.  Do you have any ideas of why this should be or what I should do to resolve this?

    My MacBook Pro doesn't start; in safe mode <shift CMD V> the message "disk0s2: media is not present" is written on the screen repeatedly but the MacBook doesn't start.  Do you have any ideas of why this should be or what I should do to resolve this?  Thanks  Eamonn

    Thanks for these suggestions: I have tried safe mode re-starts (both "verbose" and simple "shift" + power) to no avail.  I get the error message "disk0s2: media is not present".  Following this I inserted the installation disc and from there ran disc utility.  The "Verify Disk" indicated an error " invalid sibling link" which it could not repair.
    I also tried to completely re-format/erase the disk, but again got an error message "disk object invalid or unable to serialize".
    Any ideas of what could be causing this or the best solution?  I fear I am fast running out of options.

  • Macbook pro runs really slow after sleep mode

    My MBP ( MacBook Pro (13-inch, medio 2012), 2,5 GHz Intel Core i5, 8 GB 1600 MHz DDR3, Intel HD Graphics 4000 1024 MB), runs very slow after sleep mode. I notice that when I wake it up, my memory usage is nearly 8 GB. After a restart it is back no a normal level, between 2 and 5 GB depending on how many programs I am running. Any ideas what causes this? My IOS is Yosemite 10.10.2
    Kind regards

    Hi Japib
    Thanks for your reply. Here is my report:
    Problem description:
    macbook pro is really slow after sleep mode
    EtreCheck version: 2.1.8 (121)
    Report generated 4 februari 2015 20:56:34 CET
    Download EtreCheck from http://etresoft.com/etrecheck
    Click the [Click for support] links for help with non-Apple products.
    Click the [Click for details] links for more information about that line.
    Hardware Information: ℹ️
        MacBook Pro (13-inch, Mid 2012) (Technical Specifications)
        MacBook Pro - model: MacBookPro9,2
        1 2.5 GHz Intel Core i5 CPU: 2-core
        8 GB RAM Upgradeable
            BANK 0/DIMM0
                4 GB DDR3 1600 MHz ok
            BANK 1/DIMM0
                4 GB DDR3 1600 MHz ok
        Bluetooth: Good - Handoff/Airdrop2 supported
        Wireless:  en1: 802.11 a/b/g/n
        Battery Health: Normal - Cycle count 172
    Video Information: ℹ️
        Intel HD Graphics 4000
            Color LCD 1280 x 800
    System Software: ℹ️
        OS X 10.10.2 (14C109) - Time since boot: 1:36:41
    Disk Information: ℹ️
        APPLE HDD TOSHIBA MK5065GSXF disk0 : (500,11 GB)
            EFI (disk0s1) <not mounted> : 210 MB
            Recovery HD (disk0s3) <not mounted>  [Recovery]: 650 MB
            Macintosh HD (disk1) / : 498.88 GB (292.17 GB free)
                Encrypted AES-XTS Unlocked
                Core Storage: disk0s2 499.25 GB Online
        MATSHITADVD-R   UJ-8A8 
    USB Information: ℹ️
        Apple Inc. BRCM20702 Hub
            Apple Inc. Bluetooth USB Host Controller
        Apple Inc. Apple Internal Keyboard / Trackpad
        Apple Computer, Inc. IR Receiver
        Apple Inc. FaceTime HD Camera (Built-in)
    Thunderbolt Information: ℹ️
        Apple Inc. thunderbolt_bus
    Gatekeeper: ℹ️
        Mac App Store and identified developers
    Kernel Extensions: ℹ️
            /Library/Application Support/Hotspot Shield
        [not loaded]    com.anchorfree.tun (1.0.1) [Click for support]
            /Library/Application Support/Kaspersky Lab/KAV/Bases/Cache
        [loaded]    com.kaspersky.kext.kimul.44 (44) [Click for support]
        [loaded]    com.kaspersky.kext.mark.1.0.5 (1.0.5) [Click for support]
            /Library/Extensions
        [loaded]    com.kaspersky.kext.klif (3.0.4a41) [Click for support]
        [loaded]    com.kaspersky.nke (1.6.4a15) [Click for support]
            /System/Library/Extensions
        [loaded]    com.hzsystems.terminus.driver (4) [Click for support]
        [not loaded]    com.olympus.CamBlockCommandsDeviceUP (3.1.0 - SDK 10.6) [Click for support]
        [not loaded]    com.roxio.BluRaySupport (1.1.6) [Click for support]
        [not loaded]    com.sony.driver.prs2 (1.0.3d1) [Click for support]
        [not loaded]    com.wacom.kext.pentablet (5.3.3 - SDK 10.8) [Click for support]
            /Users/[redacted]/Library/Services/ToastIt.service/Contents/MacOS
        [not loaded]    com.roxio.TDIXController (2.0) [Click for support]
    Launch Agents: ℹ️
        [running]    com.epson.Epson_Low_Ink_Reminder.launcher.plist [Click for support]
        [failed]    com.epson.esua.launcher.plist [Click for support] [Click for details]
        [running]    com.epson.eventmanager.agent.plist [Click for support]
        [running]    com.kaspersky.kav.gui.plist [Click for support]
        [not loaded]    com.sony.ReaderDesktop.RunReaderDesktop.plist [Click for support]
        [not loaded]    com.trusteer.rapport.rapportd.plist [Click for support]
        [running]    com.wacom.pentablet.plist [Click for support]
    Launch Daemons: ℹ️
        [loaded]    com.adobe.fpsaud.plist [Click for support]
        [loaded]    com.anchorfree.ajaxserver.plist [Click for support]
        [running]    com.kaspersky.kav.plist [Click for support]
        [loaded]    com.microsoft.office.licensing.helper.plist [Click for support]
        [loaded]    com.oracle.java.JavaUpdateHelper.plist [Click for support]
        [running]    com.trusteer.rooks.rooksd.plist [Click for support]
        [loaded]    com.tunnelbear.mac.tbeard.plist [Click for support]
    User Launch Agents: ℹ️
        [loaded]    com.adobe.ARM.[...].plist [Click for support]
        [loaded]    com.google.keystone.agent.plist [Click for support]
        [loaded]    com.macpaw.CleanMyMac2Helper.diskSpaceWatcher.plist [Click for support]
        [running]    com.spotify.webhelper.plist [Click for support]
        [loaded]    com.valvesoftware.steamclean.plist [Click for support]
    User Login Items: ℹ️
        iTunesHelper    Programma  (/Applications/iTunes.app/Contents/MacOS/iTunesHelper.app)
        Documenten    Map  (/Users/[redacted]/Documents)
        uTorrent    UNKNOWN  (missing value)
        BambooCore    UNKNOWN  (missing value)
        BambooCore    UNKNOWN  (missing value)
        BambooCore    UNKNOWN  (missing value)
        BambooCore    UNKNOWN  (missing value)
        BambooCore    UNKNOWN  (missing value)
    Internet Plug-ins: ℹ️
        JavaAppletPlugin: Version: Java 7 Update 60 Check version
        WacomNetscape: Version: 2.1.0-1 - SDK 10.8 [Click for support]
        Default Browser: Version: 600 - SDK 10.10
        WacomTabletPlugin: Version: WacomTabletPlugin 2.1.0.2 [Click for support]
        AdobePDFViewerNPAPI: Version: 11.0.10 - SDK 10.6 [Click for support]
        FlashPlayer-10.6: Version: 16.0.0.296 - SDK 10.6 [Click for support]
        Silverlight: Version: 5.1.30514.0 - SDK 10.6 [Click for support]
        Flash Player: Version: 16.0.0.296 - SDK 10.6 [Click for support]
        QuickTime Plugin: Version: 7.7.3
        SharePointBrowserPlugin: Version: 14.4.7 - SDK 10.6 [Click for support]
        AdobePDFViewer: Version: 11.0.10 - SDK 10.6 [Click for support]
        MeetingJoinPlugin: Version: Unknown - SDK 10.6 [Click for support]
    User internet Plug-ins: ℹ️
        Google Earth Web Plug-in: Version: 7.1 [Click for support]
    Safari Extensions: ℹ️
        AdBlock
        DuckDuckGo
        Save to Pocket
        Awesome Screenshot
        URL Advisor
        Virtual Keyboard
    3rd Party Preference Panes: ℹ️
        Flash Player  [Click for support]
        Squeezebox  [Click for support]
        Trusteer Endpoint Protection  [Click for support]
    Time Machine: ℹ️
        Auto backup: YES
        Volumes being backed up:
            Macintosh HD: Disk size: 498.88 GB Disk used: 206.70 GB
        Destinations:
            My Passport [Local]
            Total size: 999.83 GB
            Total number of backups: 17
            Oldest backup: 2013-11-06 17:55:38 +0000
            Last backup: 2014-10-14 11:30:39 +0000
            Size of backup disk: Adequate
                Backup size 999.83 GB > (Disk used 206.70 GB X 3)
    Top Processes by CPU: ℹ️
            15%    mds
             5%    WindowServer
             0%    ocspd
             0%    fontd
             0%    kav
    Top Processes by Memory: ℹ️
        223 MB    kav
        198 MB    Safari
        155 MB    Mail
        137 MB    mds_stores
        77 MB    WindowServer
    Virtual Memory Information: ℹ️
        3.45 GB    Free RAM
        3.05 GB    Active RAM
        1.11 GB    Inactive RAM
        974 MB    Wired RAM
        1.64 GB    Page-ins
        0 B    Page-outs
    Diagnostics Information: ℹ️
        Feb 4, 2015, 07:21:16 PM    /Users/[redacted]/Library/Logs/DiagnosticReports/EPSON Software Updater Agent_2015-02-04-192116_[redacted].crash
        Feb 4, 2015, 07:18:08 PM    Self test - passed
    Hope this will shed some light on the problem.

  • MacBook Pro does not got to sleep mode

    OS: 10.6.8
    Since OS ??? I have the problem, that working with the account I normally use, may MacBook Pro will not go to sleep mode.
    It is strange, but only this account is affected.
    If I use another account, MacBook Pro goes to sleep mode as expected.
    All accounts I work with are standard accounts without admin rights.
    Can anybody help? E.g. some damaged *.plist to delete or so...

    AussieDJ wrote:
    Try this & output results:
    pmset -g log
    OK, here it is:
    $ sudo pmset -g log
    Power Management ASL logs.
    -> All messages with "com.apple.message.domain" key set to "com.apple.powermanagement".)
    * Domain: sleep
    - Message: Sleep: Success - AC 99 - Idle Sleep
    - Time: 7/21/11 1:10:24 AM GMT+
    - Signature: Success
    - UUID: 418D68BF-DC81-4C17-9CF1-8A66B52F0CBA
    - Result: Success
    - Sleep count : 0
    * Domain: applicationresponse.slowresponse
    - Message: PMConnection AirPort configd plug-in com.apple.powermanagement.applicationresponse.slowresponse 260 ms
    - Time: 7/21/11 1:10:25 AM GMT+
    - Signature: AirPort configd plug-in
    - UUID: 418D68BF-DC81-4C17-9CF1-8A66B52F0CBA
    - Result: Noop
    - Response time (ms): 260
    * Domain: applicationresponse.slowresponse
    - Message: PMConnection mDNSResponder com.apple.powermanagement.applicationresponse.slowresponse 3234 ms
    - Time: 7/21/11 1:10:28 AM GMT+
    - Signature: mDNSResponder
    - UUID: 418D68BF-DC81-4C17-9CF1-8A66B52F0CBA
    - Result: Noop
    - Response time (ms): 3234
    * Domain: applicationresponse.slowresponse
    - Message: PMConnection SystemUIServer com.apple.powermanagement.applicationresponse.slowresponse 213 ms
    - Time: 7/21/11 2:32:31 AM GMT+
    - Signature: SystemUIServer
    - UUID: 418D68BF-DC81-4C17-9CF1-8A66B52F0CBA
    - Result: Noop
    - Response time (ms): 213
    * Domain: applicationresponse.slowresponse
    - Message: PMConnection AirPort configd plug-in com.apple.powermanagement.applicationresponse.slowresponse 3823 ms
    - Time: 7/21/11 2:32:34 AM GMT+
    - Signature: AirPort configd plug-in
    - UUID: 418D68BF-DC81-4C17-9CF1-8A66B52F0CBA
    - Result: Noop
    - Response time (ms): 3823
    * Domain: applicationresponse.slowresponse
    - Message: PMConnection IPConfiguration com.apple.powermanagement.applicationresponse.slowresponse 3824 ms
    - Time: 7/21/11 2:32:34 AM GMT+
    - Signature: IPConfiguration
    - UUID: 418D68BF-DC81-4C17-9CF1-8A66B52F0CBA
    - Result: Noop
    - Response time (ms): 3824
    * Domain: sleep
    - Message: Sleep: Success - AC 99 - Maintenance Sleep
    - Time: 7/21/11 2:32:34 AM GMT+
    - Signature: Success
    - UUID: 418D68BF-DC81-4C17-9CF1-8A66B52F0CBA
    - Result: Success
    - Sleep count : 1
    * Domain: applicationresponse.slowresponse
    - Message: PMConnection mDNSResponder com.apple.powermanagement.applicationresponse.slowresponse 12175 ms
    - Time: 7/21/11 2:32:47 AM GMT+
    - Signature: mDNSResponder
    - UUID: 418D68BF-DC81-4C17-9CF1-8A66B52F0CBA
    - Result: Noop
    - Response time (ms): 12175
    * Domain: sleep
    - Message: Sleep: Success - AC 99 - Maintenance Sleep
    - Time: 7/21/11 4:20:48 AM GMT+
    - Signature: Success
    - UUID: 418D68BF-DC81-4C17-9CF1-8A66B52F0CBA
    - Result: Success
    - Sleep count : 2
    * Domain: applicationresponse.slowresponse
    - Message: PMConnection AirPort configd plug-in com.apple.powermanagement.applicationresponse.slowresponse 165 ms
    - Time: 7/21/11 4:20:48 AM GMT+
    - Signature: AirPort configd plug-in
    - UUID: 418D68BF-DC81-4C17-9CF1-8A66B52F0CBA
    - Result: Noop
    - Response time (ms): 165
    * Domain: applicationresponse.slowresponse
    - Message: PMConnection mDNSResponder com.apple.powermanagement.applicationresponse.slowresponse 17065 ms
    - Time: 7/21/11 4:21:05 AM GMT+
    - Signature: mDNSResponder
    - UUID: 418D68BF-DC81-4C17-9CF1-8A66B52F0CBA
    - Result: Noop
    - Response time (ms): 17065
    * Domain: sleep
    - Message: Sleep: Success - AC 99 - Maintenance Sleep
    - Time: 7/21/11 6:08:57 AM GMT+
    - Signature: Success
    - UUID: 418D68BF-DC81-4C17-9CF1-8A66B52F0CBA
    - Result: Success
    - Sleep count : 3
    * Domain: applicationresponse.slowresponse
    - Message: PMConnection AirPort configd plug-in com.apple.powermanagement.applicationresponse.slowresponse 265 ms
    - Time: 7/21/11 6:08:58 AM GMT+
    - Signature: AirPort configd plug-in
    - UUID: 418D68BF-DC81-4C17-9CF1-8A66B52F0CBA
    - Result: Noop
    - Response time (ms): 265
    * Domain: applicationresponse.slowresponse
    - Message: PMConnection mDNSResponder com.apple.powermanagement.applicationresponse.slowresponse 15991 ms
    - Time: 7/21/11 6:09:13 AM GMT+
    - Signature: mDNSResponder
    - UUID: 418D68BF-DC81-4C17-9CF1-8A66B52F0CBA
    - Result: Noop
    - Response time (ms): 15991
    * Domain: wake
    - Message: Wake: Success - AC 99 - EHC2
    - Time: 7/21/11 6:12:40 AM GMT+
    - Signature: Success
    - UUID: 418D68BF-DC81-4C17-9CF1-8A66B52F0CBA
    - Result: Success
    * Domain: applicationresponse.slowresponse
    - Message: Kernel powerd com.apple.powermanagement.applicationresponse.slowresponse 17076 ms
    - Time: 7/21/11 6:12:40 AM GMT+
    - Signature: powerd
    - UUID: 418D68BF-DC81-4C17-9CF1-8A66B52F0CBA
    - Result: Noop
    - Response time (ms): 17076
    * Domain: sleep
    - Message: Sleep: Success - AC 99 - Clamshell Sleep
    - Time: 7/21/11 7:28:31 AM GMT+
    - Signature: Success
    - UUID: D47B680C-CEB2-4EAD-AB4B-8ABF8AFFD327
    - Result: Success
    - Sleep count : 0
    * Domain: applicationresponse.slowresponse
    - Message: PMConnection mDNSResponder com.apple.powermanagement.applicationresponse.slowresponse 2033 ms
    - Time: 7/21/11 7:28:33 AM GMT+
    - Signature: mDNSResponder
    - UUID: D47B680C-CEB2-4EAD-AB4B-8ABF8AFFD327
    - Result: Noop
    - Response time (ms): 2033
    * Domain: wake
    - Message: Wake: Success - AC 92 - EC LID0
    - Time: 7/21/11 6:14:07 PM GMT+
    - Signature: Success
    - UUID: D47B680C-CEB2-4EAD-AB4B-8ABF8AFFD327
    - Result: Success
    * Domain: applicationresponse.slowresponse
    - Message: PMConnection AirPort configd plug-in com.apple.powermanagement.applicationresponse.slowresponse 3687 ms
    - Time: 7/21/11 6:14:10 PM GMT+
    - Signature: AirPort configd plug-in
    - UUID: D47B680C-CEB2-4EAD-AB4B-8ABF8AFFD327
    - Result: Noop
    - Response time (ms): 3687
    * Domain: applicationresponse.slowresponse
    - Message: PMConnection IPConfiguration com.apple.powermanagement.applicationresponse.slowresponse 3689 ms
    - Time: 7/21/11 6:14:10 PM GMT+
    - Signature: IPConfiguration
    - UUID: D47B680C-CEB2-4EAD-AB4B-8ABF8AFFD327
    - Result: Noop
    - Response time (ms): 3689

  • ITouch doesn't go into sleep mode

    I have noticed recently that my iTouch doesn't go into sleep mode. Usually the screen will go dark after a couple of minutes if it is not being used. This isn't the case. When I plug it in to charge, it doesn't go into sleep mode either. I have tried to reset with the top and home button and that hasn't worked. Does anyone have any ideas what else I can try?

    Hey SFJenn,
    Make sure Auto-Lock is set in Settings> General> Auto-Lock.
    If it is but you still see the issue, try resetting and/or restoring the iPhone.
    http://docs.info.apple.com/article.html?artnum=305743
    http://docs.info.apple.com/article.html?artnum=305744
    -Jason

  • Mac mini didn't go into sleep mode when i am conect my thunderbolt display whit an optical thunderbolt cable

    hello my mac mini didn't go into sleep mode when i am using an optical thunderbolt cable to my thunderbolt display
    has any body els this problem

    Hello josfromkerkade.  Please contact me so that I can get more details. 
    We'd like to understand which monitor you're using, how old it is, which Thunderbolt port you're using (tethered cable or TB port), & the version of firmware. 
    [email protected]
    Thanks, Mitch

  • HT201401 My phone won't lock or go into sleep mode when answering calls

    My phone won't lock or go into sleep mode when making or receiving calls. Consequently I keep activating the mute or loud speaker buttons with my cheek. Can anyone help please??

    That is a Proximity Sensor Problem, which is located above the earpiece speaker. Do you have a new screen protector or iPhone Case which could interfer with this?
    Reset iPhone, Restore iPhone.
    If you have Warranty or AppleCare Coverage make Genius Reservation and take iPhone to Apple for resolution.

  • I am running OSX Lion 10.7.4 and the computer no longer will go into sleep mode when I close the cover What happened with this option?

    I am running OSX Lion 10.78.4 and the computer will no longer go into sleep mode when I close the cover. In system preferences I can no longer find the option that allows for this energy saving feature. What happened to this option and why is this no longer happening with the latest version of Lion?

    No external monitors or devices attached. When you mention that this function only works when devices are attached that is true when you set up your preferences that way. Up until my upgrade to Lion the computer would always go into sleep mode when I closed the lid. There also used to be an option to check in system preferences that allowed you to choose this option. My question for the discussion is what happened to that option and how do you get the computer to sleep or at least the display to sleep when you close the lid as we have been able to do in the past. Thanks.

Maybe you are looking for