MacBook Pro going to screensaver while in use.

I have a 15-inch, Mid 2010 MacBook Pro and recently while I am using it it goes to sleep/screensaver as if I wasn't using it at all. As soon as I move my mouse it goes back to normal, it does this once every 10 mins approx. As you can probably tell this is quite annoying. No idea what could be causing this.
If anyone has an idea what it could be or how I can fix this please let me know.

Yes you can contact AppleCare but I not sure if they'll do anything or not. Unless you can show a manufacturing defect then Apple tend to be reluctant to replace batteries, especially outside of a few months old. No harm in asking though.
As for your problem, it sounds like you have a cell or two having a problem maintianing charge/staying active. However, given your battery is being used so little it's hard to say if this is through a lack of use. For the best battery performance you should look to accrue around 150 cycles per year, a figure you're well short of. Low battery usage is harmful to Li-based batteries.
These Apple pages should help…
http://www.apple.com/batteries/
http://www.apple.com/batteries/notebooks.html

Similar Messages

Can't boot 10.5.8 MacBook Pro from Disk Warrior while restarting using "c"

Hello,
I am helping a friend maintain her 2008 MacBook Pro (10.5.8). Have safe-booted several times, and repaired permissions.
Since she is having minor issues, I brought over my Disk Warrior v. 4.1 (CD rev. 42) which has done wonders for other Leopard Macs.
Her MacBook Pro just refuses to boot from the Disk Warrior CD when I hold down the "c" key while re-starting. It starts as usual from its OS. This has never happened to me before. So I cannot use Disk Warrior on her comp, as far as I know.
Whenever I have used this Disk Warrior CD on mine and other 10.5.8 computers, and booted holding down "c" key, everything goes swimmingly.
Grateful if anyone can anyone offer a suggestion...
Could it be her drive, her logic board, my not re-setting PRAM on her computer? Or a total mystery?
Many thanks,
Neil

Most likely because you have a version of DW that cannot boot that model. The current version of DW is 4.2. You can download DW 4.2 and create a new CD but that requires burning a new CD as part of the updating process.
Is there any particular reason why you cannot repair the disk using Disk Utility? Just boot from the Leopard installer DVD or the original installer DVD that came with the computer, then use DU from within the installer (Utilities menu) to repair the hard drive (repair, don't verify.)

17" MacBook Pro (2008) Getting hot while being used

Recently I have been noticing that my macbook pro is getting very hot when it get used, especially if it is used for video or for extended time periods. The computer gets very warm, almost hot to the touch, particularly above the keys and on the bottom.
I installed the iStat Pro widget so I could monitor the internal temps, and the CPU and GPU heatsink are approaching 175-180 degrees Fahrenheit quite often. Is this a problem? If so, what are some suggestions?

you would probably have a better chance at advice in the macbook pro discussions;
http://discussions.apple.com/category.jspa?categoryID=190

New MacBook Pro Will Not Charge While in Use

I'm not sure if this is an issue, however, I have been unable to find more information regarding this, so I thought I'd ask. While plugged in (MagSafe LED=Orange) the computer hovers around the same percentage of charge (i.e. +/-2%), even with very low to no use, and every once in a while says (Not Charging). However, when in sleep with the deck shut, it charges promptly as it should.
I've occasionally seen it charge slightly while in use while using the plug without the extension portion, however I am unsure if this is related. I have tried resetting the SMC, restart, etc. So my question simply is, is this an issue, or is the computer specified not to charge while open?
Thanks!

As eww indicated, it may be a fault with the charger. The reason for my question was because you can use the 60 watt charger that comes with the 13" model on the 15" model (which comes with an 85 watt charger), but... it will only provide enough power to operate the 15" model while in use... it does not provide enough power to both operate the machine while charging it. It will only charge with the machine shut down. Your symptoms sounded very similar... but as you're using the correct charge, it may just be a bum charger. These types of things tend to fail early on if they're going to fail at all. With it only being a few weeks old, that would also seem to make it more likely to be a faulty charger. Apple tends to be very good with these things. If you have an Apple store nearby, set up a Genius appointment online. There's a good chance they'll just replace the charger for you. It's a good to bring it in though so they can check it out for you just in case the problem is with the charging circuitry in your Mac and not the charger.

My MacBook Pro gets very slow while doing work like watching movies and using net .. video gets lag very often

My MacBook Pro gets very slow while doing work like watching movies and using net .. video gets lag very often and while surffing on net it gets very slow ...

First, back up all data immediately, as your boot drive might be failing.
There are a few other possible causes of generalized slow performance that you can rule out easily.
Reset the System Management Controller.
If you have many image or video files on the Desktop with preview icons, move them to another folder.
If applicable, uncheck all boxes in the iCloud preference pane.
Disconnect all non-essential wired peripherals and remove aftermarket expansion cards, if any.
Check your keychains in Keychain Access for excessively duplicated items.
Boot into Recovery mode, launch Disk Utility, and run Repair Disk.
Otherwise, take the steps below when you notice the problem.
Step 1
Launch the Activity Monitor application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Activity Monitor in the icon grid.
Select the CPU tab of the Activity Monitor window.
Select All Processes from the menu in the toolbar, if not already selected.
Click the heading of the % CPU column in the process table to sort the entries by CPU usage. You may have to click it twice to get the highest value at the top. What is it, and what is the process? Also post the values for % User, % System, and % Idle at the bottom of the window.
Select the System Memory tab. What values are shown in the bottom part of the window for Page outs and Swap used?
Next, select the Disk Activity tab. Post the approximate values shown for Reads in/sec and Writes out/sec (not Reads in and Writes out.)
Step 2
If you have more than one user account, you must be logged in as an administrator to carry out this step.
Launch the Console application in the same way you launched Activity Monitor. Make sure the title of the Console window is All Messages. If it isn't, select All Messages from the SYSTEM LOG QUERIES menu on the left. If you don't see that menu, select
View ▹ Show Log List
from the menu bar.
Select the 50 or so most recent entries in the log. Copy them to the Clipboard (command-C). Paste into a reply to this message (command-V). You're looking for entries at the end of the log, not at the beginning.
When posting a log extract, be selective. Don't post more than is requested.
Please do not indiscriminately dump thousands of lines from the log into this discussion.
Important: Some personal information, such as your name, may appear in the log. Anonymize before posting. That should be easy to do if your extract is not too long.

How to put display on screensaver while still using the beamer?

How can i put my display on screensaver while still using the beamer?
My beamer can be on for a long time, i would like to use my screensaver at the same time, but then the beamer screen also goes to screensaver.
Is there a way to use just the beamer screen, while the computer screen is on screensaver?
I use a macbook pro with Mavericks.
Thanks in advance - Daan

What you can do is hiding the tabs (see pic below) and force the active tab programmaticily
Hope this helps
Message Edité par TiTou le 09-20-2006 10:35 AM
When my feet touch the ground each morning the devil thinks "bloody hell... He's up again!"
Attachments:
Clipboard01.png ‏151 KB

Can someone connect in FaceTime if they are using a friends Macbook Pro, yet, doens't have an Apple ID?? For example, I have an IPAD and a Macbook Pro. Can I connect to FaceTime on my Macbook Pro and connect with a friend using my IPAD????

Can someone connect in FaceTime if they are using a friends Macbook Pro, yet, doens't have an Apple ID?? For example, I have an IPAD and a Macbook Pro. Can I connect to FaceTime on my Macbook Pro and connect with a friend using my IPAD????

I have also tried changing the contact emails(you can contact me by) in Facetime(diff email for IPAD and Macbook Pro). Facetime tried the call, I see the accept buttom appear and it goes away as the call never connects? Any ideas??

My macbook pro goes to sleep by it does not wake up. I have to restart it. I had recently to change the board in the attached Thunderbolt display.

my macbook pro goes to sleep by it does not wake up afterwards. I have to restart it. I had recently to change the board in the attached Thunderbolt display, because I noticed that the same problem arose when the display was attached.
Now with the new board, it can't be the display's fault. I hope it is not macbook pro's main board fault. Maybe hasthe notebook board been damaged by the faulty display?
To bring my MacBook Pro to service will slow down my work. This is why I am posting this message, in the hope to be able to run a diagnostic test myself.
Thanks a lot, in advance.

Hello Aminetti,
It sounds like your computer goes to sleep, and will not wake up, so you must manually restart your computer. I recommend the troubleshooting in the following article:
OS X: When your Mac doesn't sleep or wake
http://support.apple.com/kb/TS5357
Reset SMC
Reset NVRAM/PRAM
Test with external devices disconnected
Try Safe Mode
Try another user account
Thank you for using Apple Support Communities.
All the best,
Sterling

Late 2011 MacBook Pro - how much hard drive space used for OS, iLife, system files?

Dear Community,
I've just taken delivery of a used MacBook Pro. It's pristine, hardly used.
It has a 750Gb hard drive with 500Gb free. Does this sound about right or could there be hidden files lurking unseen? The previous user had installed Microsoft Windows but I can't find any sign of a partition for that and the previous owner said he'd erased everything except Lion, iLife and system files, etc.
I looked in System Info which it isn't showing a large partition. I also looked in Disk Utiliy under Partition which seems to show un "current" a single drive with no partitions and around 200Gb used. It just seems a lot for the basic files.
I have another 100Gb to add to that when I migrate my PowerBook over in the next few days. That's okay while I have the current drive but I've purchased a 500Gb Crucial SSD drive to replace it so that will leave 200Gb free.
I know I can remove the super drive and put my 750Gb drive in its place but I need super drive for viewing DVDs.
I would grateful for any feedback.
K

Thanks everyone for your help with this.
After hours of trying to figure this out I located around 150Gb in total but found there was no way of removing references to the original owner whose "Home" file in Finder remained prominent.
So I elected to erase the drive and reinstall Lion using Disk Utility. It took two hours or so to download and I took the precaution of plugging directly into Ethernet rather than my Airport.
When the download was complete I was able to input fresh details so all trace of the original owner has been removed.
Once that was done I upgraded to Lion 10.7.5 and was able to download Garage Band, iMovie and iPhoto for free from the App Store.
Anybody contemplating doing the same should check that their machine is elligible before erasing as Apple does an auto check before downloading.
Here's the state of the hard drive now:
Thanks again and what a great resource the community forum's are:-)
K

I'm a singer and recently bought a Macbook Pro. I'd like to use it to play music through my PA system but it doesn't seem compatible as no sound is coming through. It is however coming through my smaller Bose system.

I'm a singer and recently bought a Macbook Pro. I'd like to use it to play music through my PA system but it doesn't seem compatible as no sound is coming through. It is however coming through my smaller Bose system. My main system is Alto APM80.1000 with Proel speakers.

Hi it's a headphone jack and two larger (microphone type jacks?) at the other end. Please excuse my not not knowing the name of anything - I know where everything goes but not the names! So if I press Alt and the sound icon at the same time what output should I be choosing?
I've tried plugging into the red and white tape in tape out and the front of the amp with a headphone/red and white jack lead and a slight sound comes out but of bad quality.
When I'm going through my bose it's an easy headphone to headphone lead and is working perfectly.
Thanks

Every time I try to back up my Macbook Pro with an external hard drive using Time Machine, I receive the error of "the disk does not have enough space". I have a 500GB hard drive and only 120GB Macbook. It worked fine before the latest Maverick's

Every time I try to back up my Macbook Pro with an external hard drive using Time Machine, I receive the error of "the disk does not have enough space". I have a 500GB external hard drive and only 120GB Macbook. It worked fine before the latest Maverick's update. Any help would be greatly appreciated.

My guess would be it has created an entirely new backup of your drive when you upgraded to Mavericks.
See Here: http://pondini.org/TM/1.html
And here: http://pondini.org/TM/9.html
Peruse the whole site. There is a lot of information there.

My Macbook Pro cannot connect to the internet using an ethernet cord.

My Macbook Pro cannot connect to the internet using an ethernet cord. It was working fine for weeks, then all of a sudden just stopped. What could the problem be?

Hi bean07670,
If you are having an issue with the Ethernet connection on your MacBook Pro, you may find the following article helpful:
Mac OS X: Troubleshooting a cable modem, DSL, or LAN Internet connection
http://support.apple.com/kb/TS1317
Regards,
- Brenden

I am trying to connect my Macbook pro 2010 to my Samsung HDTV using a mini display port to hdtv cable. Trying to play a slide show in IPhoto but I only get sound with no picture. Does anyone have any suggestions?

I am trying to connect my Macbook pro 2010 to my Samsung HDTV using a mini display port to hdtv cable. Trying to play a slide show in IPhoto but I only get sound with no picture. Does anyone have any suggestions?

I keep saying this over and over, in the hope that people who do a search will find it. Apple cannot possibly test for or be reponsible for the bazillion combinations of adapter, cables, and TV's out there. The only monitors that are 100% guaranteed to work with the MacBook Pro are the Cinema Displays and Thunderbolt Displays, because, they're made by Apple. They're expensive, but they work perfectly.
My guess is that you bought a cheap MDP to HDMI cable, or have a defective one. From my reading of these boards over the past few months, cheap cables have a high failure rate. And the regular priced ones have only a slightly less of one. Try a new one. Make sure you do not damage the Thunderbolt port.

My macbook is going to sleep while I'm working or viewing something. I will sometimes have to open and close it several times to get it to "wake up" again. Any suggestions?

my macbook is going to sleep while I'm working or viewing something. I will sometimes have to open and close it several times to get it to "wake up" again. Also, no sound comes out of my Macbook. I only hear with earbuds or headphones. Any suggestions?

If you have more than one user account, you must be logged in as an administrator to carry out these instructions.
Triple-click anywhere in the line below to select it:
syslog -k Sender kernel -k Message CSeq "Previous Shutdown" | tail | open -f -a TextEdit
Copy the selected text to the Clipboard (command-C).
Launch the Terminal application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Terminal in the icon grid.
Paste into the Terminal window (command-V).
The command may take a noticeable amount of time to run. Wait for a new line ending in a dollar sign (“$”) to appear.
A TextEdit window will open with the output of the command. Post the contents of that window, if any — the text, please, not a screenshot. The title of the window doesn't matter, and you don't need to post that.

My MacBook Pro is running very slow when using the internet and sometimes gives the pinwheel of death, any suggestions on how to fix?

My MacBook Pro is running very slow when using the internet and sometimes gives the pinwheel of death, any suggestions on how to fix?

<http://www.thexlab.com/faqs/sbbod.html>

MacBook Pro going to screensaver while in use.

Similar Messages

Maybe you are looking for