Macbook Pro-mid 2013 Maximum RAM

Hello, i have a Macbook Pro-mid 2013 (13" inch-intel Core i5 2,5ghz-4go RAM) and i'd like to upgrade the RAM to the maximum possible.
I saw that officialy, the maximum is 8go but that it's possible to use 16go without problems.
Is there any risk to upgrade to 16go?
What brands would be the best choice?
Thank you for your help.

You note two different machines, the MacBook Pro Mid-2012 and Mid-2013.  There is no Mid-2013 MBP, but the Early and Late 2013 models cannot be upgraded after sale.
The Mid-2012 can be upgraded to 16 GB but like all Macs, you need to use ram guaranteed for a Mac as they are very sensitive to the timing of the memory.  Buy from OWC, http://www.macsales.com or Crucial, http://www.crucial.com

Similar Messages

  • MacBook Pro mid 2013 Running Kinda Slow?

    Hello there.
    Small bit of info
    I'm new to mac, so i'm still learning as i'm a windows pc Video editor/Gamer user.
    My windows pc is fast so i'ts probally just me being picky. However i feel like every hour i'm typing in "purge" in the terminal just to get more free ram.
    Specs
    i5 @2.5 Ghz
    4GB @1600Mhz
    MacBook Pro Mid 2013
    Mountain Lion
    500GB HDD Drive
    More info on problem/concern
    When logging back in my mac some times i click on icons they litrally either take 8-10 seconds to open.
    At times with Adobe premiere pro CC & Adobe after effects CC open at the same time. At times the mac grinds to a solid halt and it just dose not respond to clicks ect ect.
    Some times it even takes a while just to open the finder or prefrences.
    Adobe can take 25-35 secodns to finally open.
    Just some questions on mac in general
    Dose mac slowly get faster the more you use it, i seem to notice one times my mac was running 3 programs at once. And it was handelling it really well.
    Will is OS mavericks make my mac work a lot faster. It says it will, but no idea if new mac OS's actually make much diffrence.
    Would 8GB ram make my mac a LOT faster. Like 10fps more in games. 20fps more. Would it let me run dual programs better? Like adobe programs better.
    Any way, sorry for the hord of questions.
    P.S
    Samuel Benjamin Bignell

    On the problem/concern
    1.this can be normal, especially when using a traditional HDD. the computer is spinning up the drive again and looking for the applications you are starting. one thing that can help is to restart you computer simi often (2-3 time a week at least) and making sure that you are quitting appliacations.
    2. the CC products are stil fairly new. maybe reach out to adobe and see if they know about the issue.
    3. hard to tell you what's happening. depends on what else is going on.
    4. Adobe programs are big. again pretty normal for a newer mac with a traditional HDD.
    Questions
    1. not generally, but it depends on what specifically is going on.
    2. in the past OS upgrade generally provide noticable speed bumps on macs that are less then 2 years old.
    3. YES. this is one of the cheapest and most noticable upgrades you can do. this wont let apps launch faster, but multitasking will see a boost. RAM is user servicable and is covered in the manual. another upgrade that you may want to look into is installing an SSD (also user servicable). this will boost your boot time, app launch time, wake from sleep, all of these fun things.

  • Macbook pro late 2013's Ram

    Can you upgrade a macbook pro late 2013's model Ram from 8 gb to 16 gb?

    Gnomish8 wrote:
    Yes. It looks like the maximum supported memory for the 15 inch retina is 16GB.
    You can find your systems tech specs here.
    The RAM is soldered into the Logic Board......So technically the RAM can NOT be upgraded on the rMBP.

  • I want to upgrade my macbook pro mid 2010's ram

    I want to upgrade my macbook pro's ram to 8gb's I don't want to spend $200 on ram from apple, i Know that with buying it from apple, if it doesnt work they will do it for you, and it guranteed to work, i just don't have the money to do that.
    they outlined how to do it here http://support.apple.com/kb/HT1270#link1
    and i found some memmory here
    http://www.crucial.com/store/mpartspecs.aspx?mtbpoid=2F9CE069A5CA7304
    I am confident in my computer knowledge that I can install ram in a mac, i've done it to dozens of pc's
    so what i'm looking for is reassurance before I do anything thank you

    There should no problem in installing 8 GB RAM in your MBP.  Crucial is one of the best sources of RAM for Macs.  Now if you are so inclined, you can install 16 GB from OWC, the other reliable source for Mac RAM.
    blog.macsales.com/16353-owc-announces-maxram-memory-upgrades-to-16gb-for-2010-ma c-mini-macbook-and-macbook-pro
    Ciao.

  • 15" Macbook Pro mid-2010, 16GB RAM upgrade possible?

    Hi all,
    I've been looking around all the support forums and questions asked etc..
    But I can't find a definitive answer about support for the 15" mid-2010 MBP being able to use 16GB (and be stable).
    I'm aware that it's perfectly fine on the 13" model, however I have the 15" i7.
    From what I've been reading it's because of the motherboard/Graphics chip/EFI BIOS incompatibiity with anything more than 8GB. (Which is silly really, as the same Intel core i7 can have up too at least 32GB of RAM on any none-Mac system.)
    Have Apple not pushed out an EFI BIOS update that could allow the use of 16GB RAM?
    If this has been clearly answered elsewhere (and I haven't found it), feel free to point me in the right direction.
    Thanks, Jon.

    Unfortunately, 8GB is the limit. I have the same machine. Why it works on the 13" and not the 15" is ridiculous, but that's how it is.

  • HT5266 The screen issue. I do have a retina macbook pro mid 2013.

    The screen seems to be decolonizing, you can see it at the bottom corners, while background is black. I mean those places are getting whiter (brighter) that all the rest screen. And it seems to be extending. What could you advice?

    This is a picture of the actual issue with retina screen in my case.

  • MacBook Pro mid 2013 13' gets stuck on White screen after login.

    I'm in safe mode right now. I Booted it up in Safe Mode by holding down the shift key during startup. What do I do now to not get the white/grey screen during startup after login?

    Mac OS X: Gray screen appears during startup
    If the grey screen occurs when you boot normally (not safe mode) try bypassing your Login Items by holding a Shift key in the same manner during login (i.e. not during boot). If you can log in, you effectively isolated the problem to one of more of your Login Items.

  • I have a mid 2007 MacBook Pro with 2GB of RAM and NVIDIA GeForce 8600M graphics. Is it possible to upgrade the RAM and the graphics card?

    I have a mid 2007 MacBook Pro with 2GB of RAM and NVIDIA GeForce 8600M graphics card. Is it possible to upgrade the RAM and the graphics card?

    The RAM can be upgraded as indicated below. The Graphics card can not be upgraded.
    Maximum Memory
    6.0 GB (Actual) 4.0 GB (Apple)
    Memory Slots
    2 - 200-pin PC2-5300 (667MHz) DDR2 SO-DIMM

  • HT1270 My mid 2010 MacBook Pro has the maximum 8 GB memory cards installed. Can it be upgraded to 16 GB? Are there compatible 8 GB cards available?

    My mid 2010 MacBook Pro has the maximum 8 GB memory cards installed. Can it be upgraded to 16 GB? Are there compatible 8 GB cards available?

    I have a similar question..  13" macbook pro, mid 2010- having problems with spinning beach ball..  like someone from Mars has taken over the computer..   - the specs are below..   would it help if I added more RAM?   If  yes, any suggestions where/ what to buy?  This only started after upgrade to Mountain Lion from SNL. 
    MacBook Pro 13 inch mid 2010
      Model Identifier:    MacBookPro7,1
      Processor Name:    Intel Core 2 Duo
      Processor Speed:    2.66 GHz
      Number of Processors:    1
      Total Number of Cores:    2
      L2 Cache:    3 MB
    Memory  4 GB 1067 MHz DDR3
      Bus Speed:    1.07 GHz
      Boot ROM Version:    MBP71.0039.B0E
      SMC Version (system):    1.62f7
    Graphics  NVIDIA GeForce 320M 256 MB
    BANK 0/DIMM0:
      Size:    2 GB
      Type:    DDR3
      Speed:    1067 MHz
      Status:    OK
      Manufacturer:    0x80AD
      Part Number:    0x484D54313235533654465238432D47372020
      Serial Number:    0x27A0B2F9
    BANK 1/DIMM0:
      Size:    2 GB
      Type:    DDR3
      Speed:    1067 MHz
      Status:    OK
      Manufacturer:    0x80AD
      Part Number:    0x484D54313235533654465238432D47372020
      Serial Number:    0x2740B300

  • Installing 8GB ram on MacBook Pro (Mid 2010)

    Hi, I have bought 8GB(2*4GB) ram to install on my macbook pro, when I install both I get a black screen but when installing one or the other with one of the original ram they both work. What can I do to fix this problem??

    Topher Kessler California
    Re: Installing 8GB ram on MacBook Pro (Mid 2010) 
    Jun 1, 2013 8:00 AM (in response to emiliosh)
    When you install RAM, reboot your computer with the "D" key held down (or the Option-D keys). These will load the Apple Hardware Tests.
    With these tests open, check the box for the extended memory test, and then start the test. This will have the system thoroughly test the RAM for errors.
    In your case, it appears you may have a bad set of RAM modules, but you can check them using the method above.
    When you have them paired with your original RAM, how much memory does the system report as being available when you select About This Mac in the Apple menu? If you are using Lion or Mountain Lion, then in this panel click "More Info" and then select the "Memory" section, and see what the system reports as being installed.
    Is this RAM test necessay with every upgrade of memory or just if you have problems after the upgrade
    Thanks

  • Apple Unibody 13.3" MacBook Pro (Mid-2010): 4GB vs. 8GB DDR3 1066MHz Memory (RAM).

    Apple Unibody 13.3" MacBook Pro (Mid-2010): 4GB vs. 8GB DDR3 1066MHz Memory (RAM).
    1. About my Mac.
         Processor: Intel® Core 2 Duo (2.66GHz)
         Memory (RAM): 4.00GB DDR3 1066MHz (2 x 2.00GB)
         Hard Drive: 320GB 5400RPM (Apple Stock HD)
         Graphics: NVIDIA GeForce 320M (256MB)
         Operating System: Mac OS X Lion (10.7.1)
    2. My concerns/questions
         For quite some time now, I've been planning to upgrade the memory (RAM) of my MacBook Pro from 4.00GB (Apple Stock) to 8.00GB. In terms of "FASTER BOOT TIMES, IMPROVED RESPONSIVENESS (OPENING and CLOSING PROGRAMS, FILES & ETC.), SMOOTHER GRAPHICS, ABILITY TO OPEN MORE PROGRAMS SIMULTANEOUSLY AND OVERALL IMPROVEMENT IN PERFORMANCE", does it really make a BIG difference?
         If ever I am going to pursue this upgrade, should I let Apple do the upgrade or buy the parts and do it myself?
         If I am going to buy the parts and install it myself, what brand do you recommend? Crucial, Kingston, OWC & etc.?
         Why does Apple charge so much for memory (RAM) upgrades? Is the memory module they are using any special compared to the ones we can find in Amazon (Crucial, Kingston, OWC & etc.)?
    Thanks for helping me out with my concerns.

    I recommend OWC RAM because it's reasonably priced and OWC's support is great if you ever need it. I recommend installing the RAM yourself because it's dead simple. There is no good reason for anyone ever to pay Apple's prices for RAM.
    I don't think you will see faster boot times with more RAM, but that shouldn't be a concern, because there's seldom any need to shut down or restart a MBP. Just put it to sleep when you aren't using it, unless you won't use it again for more than two or three days. Opening and closing programs won't benefit significantly from more RAM either, but when running multiple large programs at once, you will see a significant improvement in their performance. It's well worth the small investment ($65) to upgrade from 4GB to 8GB.
    http://eshop.macsales.com/shop/memory/Apple_MacBook_MacBook_Pro/Upgrade/DDR3

  • Macbook pro mid 2010 15" 16 GB ram upgrade possible?

    I recently purchased RAM from Crucial.com for 8 GB and after having researched a bit online I've heard of users upgrading to 16 GB.  Is this true? 
    Here are the specs of my cpu:
    MacBook Pro 15" Mid 2010
    OSX Yosemite 10.10.1
    Memory 8 GB 1067 MHz DDR3
    2.53 GHz Intel Core i5
    Can anyone give me insight?  I'm not very computer literate, but could use all the advice I could get.  Thank you kindly

    Good morning ipodsmut,
    The MacBook Pro mid 2010 model supports up to 8GB of RAM. See this Apple specifications article -
    MacBook Pro (15-inch, Mid 2010) - Technical Specifications
    Thanks for using Apple Support Communities.
    Best,
    Brett L 

  • MacBook Pro mid 2012 15" - one RAM slot gone bad

    Hi,
    Has anyone ever had the issue with not working RAM slot? My MacBook Pro mid 2012 (non-retina) suddenly froze and after restart was beeping three times every few seconds. I found out that the beeping signals bad RAM. Bought new chips, and the problem still exists. My mac can now run on one slot with 4GB RAM.
    I did check the placement of the chips in the slots, i also checked one slot at a time, and one of them has gone broken.
    Any ideas on how to make it run again? or if it is possible to replace the slots?
    Brgds
    Marek
    MacBook Pro 2,7GHz Intel Core i7 / OSX 10.9.4

    The Apple-accepted cure for a dead RAM slot is a new logic board. Unless you ahve AppleCare, that will be an expensive fix.
    An Apple service option is the "depot repair." Instead of working on your computer in the Apple Store, they send it to a centralized refurbishment facility where they fix anything they find wrong (except for cosmetic damage and damage from abuse like dropping) for a flat fee of a little over US$300. That is between 30 and 40 percent of the parts and labor charges if Apple installs a new board in an Apple Store. Sometimes they will install an new battery at the depot without increasing the flat fee.
    The downside is that it takes about a week; for that level of cost savings, I could do without my computer for a week.
    So take it to Apple and ask about a depot repair.
    A low-tech and low-cost option is to expand on what you are doing now--using one slot. Although the official RAM limit on your model is 8GB RAM (two 4GB models), your model can actually handle a total of 16GB (two 8GB modules. You can ignore the dead slot and put an 8GB module in the good slot. My 2012 MBP has 8GB RAM and is completely happy running Mavericks.
    Be sure to ONLY get the RAM from an Mac-savvy vendor. For over a decade I've bought all our Mac RAM from one supplier. This is their page for an 8GB module for your MBP model:
    http://eshop.macsales.com/item/OWC/1600DDR3S8GB/
    I would also trust Crucial on this one. For a change they recognize that your model can use more RAM than stated in Apple's outdated specs:
    http://www.crucial.com/usa/en/compatible-upgrade-for/Apple/macbook-pro-%2813-inc h-and-15-inch%2C-mid-2012%29

  • My Macbook pro Mid 2012 Model Seems to be using too much RAM

         Hello everybody, I recenlty bought a Macbook pro Mid 2012 Model and I absolutely fell in love with it! I use it everyday for school, work, and for my musical hobby.
         I haven't had a single problem with it until recently, and it seems like the RAM memory is being all used up without me even running programs. This problem barely started rougly 2-3 weeks ago and it's becoming annoying. I do plan to upgrade the ram soon seeing as the extra RAM will help run my engineering software I'm going to be using.
    Anywho I'm just looking for tips, suggestions or answers as to why this problem is occuring. Also heard from a fellow employee that Google Chrome can cause this problem with RAM and battery life as well.

    Stop using Chrome for any number of reasons and stick to Safari. An aspect of OS X memory management is to take over as much memory as possible in order to better manage the memory, however, this does not mean you are running out of memory. You only run out of memory when you try to run too many applications concurrently given the amount of RAM you have. You will know when that happens because the computer will slow down, you will see the beachball a lot, everything you do takes forever, and the hard drive will be grinding away.
    About OS X Memory Management and Usage
    Using Activity Monitor to read System Memory & determine how much RAM is used
    OS X Mavericks- About Activity Monitor
    Understanding top output in the Terminal
    The amount of available RAM for applications is the sum of Free RAM and Inactive RAM. This will change as applications are opened and closed or change from active to inactive status. The Swap figure represents an estimate of the total amount of swap space required for VM if used, but does not necessarily indicate the actual size of the existing swap file. If you are really in need of more RAM that would be indicated by how frequently the system uses VM. If you open the Terminal and run the top command at the prompt you will find information reported on Pageins () and Pageouts (). Pageouts () is the important figure. If the value in the parentheses is 0 (zero) then OS X is not making instantaneous use of VM which means you have adequate physical RAM for the system with the applications you have loaded. If the figure in parentheses is running positive and your hard drive is constantly being used (thrashing) then you need more physical RAM.
    Adding RAM only makes it possible to run more programs concurrently.  It doesn't speed up the computer nor make games run faster.  What it can do is prevent the system from having to use disk-based VM when it runs out of RAM because you are trying to run too many applications concurrently or using applications that are extremely RAM dependent.  It will improve the performance of applications that run mostly in RAM or when loading programs.

  • I have a 15' Macbook Pro, mid 2010 running Mavericks. I want to upgrade the hardware by increasing the RAM to 8GB and replacing the HD for a SDD one. What would be the best way to install mavericks on the new HD? I have the original OS X CD.

    I have a 15' Macbook Pro, mid 2010 running Mavericks. I want to upgrade the hardware by increasing the RAM to 8GB and replacing the HD for a SDD one. What would be the best way to install mavericks on the new HD? I have the original OS X CD.
    From what I read, I have 2 choices: 1. to install OSX and then upgrade to Mavericks, but I'm not sure if this would be possible (to upgrade directly from OSX to Mavericks); and 2. to use a software called Super Duper.
    I wouldn't like to have to use a third party software to do this, so the question is: is there a better way to install directly the Mavericks not having to use a third party software?

    Install the new drive in the computer.
    Install the old drive in an external USB or Firewire enclosure.
    Boot the computer from the Recovery HD on the external drive.
    Use Disk Utility to partition and format the new internal drive.
    Clone your external drive to the internal drive.
    How to replace or upgrade a drive in a laptop
    Step One: Repair the Hard Drive and Permissions
    Boot from your OS X Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Installer menu (Utilities menu for Tiger, Leopard or Snow Leopard.) After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list.  In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive.  If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer.
    If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
    Step Two: Remove the old drive and install the new drive.  Place the old drive in an external USB enclosure.  You can buy one at OWC who is also a good vendor for drives.
    Step Three: Boot from the Recovery HD on the external drive.  Restart the computer and after the chime press and hold down the OPTION key until the boot manager appears.  Select the icon for the Recovery HD then click on the downward pointing arrow button.
    Step Four: New Hard Drive Preparation
      1. Open Disk Utility from the main menu and click on the Continue button.
      2. After DU loads select your new hard drive (this is the entry with the
          mfgr.'s ID and size) from the left side list. Note the SMART status of
          the drive in DU's status area.  If it does not say "Verified" then the drive
          is failing or has failed and will need replacing.  Otherwise, click on the
          Partition tab in the DU main window.
      3. Under the Volume Scheme heading set the number of partitions from
          the drop down menu to one. Set the format type to Mac OS Extended
          (Journaled.) Click on the Options button, set the partition scheme to
          GUID  then click on the OK button. Click on the Partition button and
          wait until the process has completed.
      4. Select the volume you just created (this is the sub-entry under the
          drive entry) from the left side list. Click on the Erase tab in the DU main
          window.
      5. Set the format type to Mac OS Extended (Journaled.) Click on the
          Options button, check the button for Zero Data and click on OK to
          return to the Erase window.
      6. Click on the Erase button. The format process can take up to several
          hours depending upon the drive size.
    Step Five: Clone the old drive to the new drive
      1. Using Disk Utility still opened.
      2. Select the destination volume from the left side list.
      3. Click on the Restore tab in the DU main window.
      4. Check the box labeled Erase destination.
      5. Select the destination volume from the left side list and drag it to the
          Destination entry field.
      6. Select the source volume from the left side list and drag it to the
          Source entry field.
      7. Double-check you got it right, then click on the Restore button.
    Destination means the new internal drive. Source means the old external drive.
    Step Six: Open the Startup Disk preferences and select the new internal volume.  Click on the Restart button.  You should boot from the new drive.  Eject the external drive and disconnect it from the computer.

Maybe you are looking for

  • 5.1 Surround Sound back two and centre speakers suddently stopped working in VIS

    Hello, In January I installed Windows Vista onto my pc. I didn't have any issues with the sound card at all. All of my speakers were working correctly. The sound card I have is the Creative Soundblaster Li've 24bit internal. I installed the drivers f

  • Connecting Laptop to Wireless Network

    I have been trying for days to connect my laptop to my Wireless Home Network on Windows XP. Verizon sent a new modem router. - DLINK 2750B. It works just fine with DESKTOP and at other rooms wired for CAT5.  However, can't get laptop setup to work. T

  • Vendor description in MB51

    Dear All In the report MB51 Vendor and customer numbers are displaying. But my client wants the description along with the number. I have checked the layout .But description is not their. Kindly kind me to achieve. Shobana

  • Use of Xerces Parser in out application with Oracle App Server 9.0.4

    The problem in brief: Our product is a web-app that runs under various Application servers. One of our customers who uses Oracle App server, recently upgraded from 9.0.2 (9g) to 9.0.4 (10g), and our product no longer works with the latter version. Ou

  • Thread in JTree GUI

    I have a GUI with a JTree. Each time I select a node, the valueChanged method is called and a new thread is being started. Now, for various reasons, I only want to have ONE single thread, that is, i don't want Java to start a new thread each time i s