Macbook Pro Retina Display (Oct 2013)

I have the new MBPr that came out in late october 2013. The battery is obviously not going to last me 9 hours because I'm using it.. but it sure does drain fast. Most I do is internet browsing and listen to music on youtube. Is there something I can reset with the battery to maximize the battery life? Also I'm a new macbook user and I don't know when I should charge my macbook. I've been charging it when the battery is almost dead but I've read on some forums that this is bad for the battery life. PLEASE HELP ME! The battery life is really upsetting..

The 'estimated' 9 hours of battery time is onlt for 'light' Internet browsing - with few Flash movies being viewed - and maybe a couple of low-consumption applications being open, all energy saver settings set just right, etc.
BUT...
You shouldn't let the battery run down to almost no power. If you're able, plug your computer in just as battery % reaches about 30. You can even leave the adapter plugged in whenever you're near a receptacle. If you're plugged in almost 100% of the time, let your battery run down to about 30-40% at least once every two weeks before plugging back into mains.
Be sure and set your Energy Saver prefs to lower the screen brightness and keyboard backlight brightness as low as possible.
You may not get a solid 9 hours on battery, but at least 8 hours can be reasonably expected.
Good luck,
Clinton

Similar Messages

Glitch at shutdown? Macbook pro retina display late 2013 model

Hi,
I have the late 2013 model of the macbook pro retina display. Since the past few weeks, I've been noticing a glitch at shutdown. This started to happen after my macbook asked me for my keychain password. How can I fix this glitch?
Before the whole keychain password: My mac would take a good 30 seconds to turn off properly. There would be a grey screen for a good 30 minutes.
After the whole keychain password: My mac just shuts off in a second literally but the grey screen doesnt appear. These a glitch. You can see the dock trying to go down at shutdown but because of the glitch it just stays there.
How can I fix this? Should I get it checked out?

Please make a Genius Appointment and take it in for service. Ask for the glitch specialist.

I recently bought the macbook pro retina display early 2013? should I return it and get the late 2013 model?

i recently bought the macbook pro 15 inch retina display early 2013? should I return it and get the late 2013 model?

You have 14 days exchange
New retina has which yours doesn't -
802ac wifi, very very fast
Haswell cool running processor
Longer batt life
Lightweight form factor
Faster PCIe SSD
Overall a better machine to have yes
Your choice is subjective to your needs however
peace

Can my Flash Storage on my Macbook Pro Retina Display (Late 2013) be upgraded?

I feel like my 256GB Flash Storage is not going to be enough for me, and I have bought it over a month ago. Anyone know my options on upgrading, other than using a portable storage drive.
Thanks.

There's no 3rd party for that yet. The company to watch would be Other World Computing. They do have SSD's for previous generations of Retina, but the new models have a different interface. One thing you can do is to add an SD card in the slot and format it as OS X Extended (Journaled) NOT case sensitive. It's nowhere near as fast as your SSD, but it's convenient and maybe good for less important data files.
http://www.amazon.com/Lexar-Professional-128GB-Memory-LSD128CTBNA400/dp/B007BZRX K2/ref=sr_1_3?ie=UTF8&qid=1396915819&sr=8-3&keywords=sd+card+128+gb

Line in Macbook Pro retina display late 2013 model

there is the very thin line on the screen sometimes pink, red, green colour. towards the left side of the screen. the line goes of sometimes comes back. I have read many people had this problem, but the posts was last years. is this hardware or software problem?

Take the MBPr back to an Apple store genius bar and have the techs check it out while still under warranty...a graphics module problem will need their attention.

When I ordered my MacBook Pro (Retina Display late 2013) my order had said that the computer would come with an accessory kit but instead it came with a country kit. What is a country kit and why was the accessory kit exchanged with it?

Somehow when they were processing my order the accessory kit changed Into a country.

Contact the place where you purchased the MBP & ask them.

I have a macbook pro retina display and a gaming mouse and i can't play with it

I have this gaming mouse not an apple mouse and when i try to play with the mouse i don't move but i can walk with the WASD but with the mouse i can't move and i've had trouble for a while and i really want to know how to fix this can anyone help me, my mac is a macbook pro retina display late 2013.

Hello abmorgan646
Check out the article below to try out a few things to resolve issues with the flickering display on your MacBook Pro Retina. You may need to reset the NVRAM, if it does not resolve the issue, then there are links fur further assistance.
Apple computers: Troubleshooting issues with video on internal or external displays
http://support.apple.com/kb/ht1573
Regards,
-Norm G.

Hello, I have a MacBook pro retina 13" early 2013, and i am not sure if I can use a 4k2k display Monitor with my Macbook, please help!

Hello, I have a MacBook pro retina 13" early 2013, 2,6 GHz Intel Core i5 and Intel HD Graphics 4000 1024MB,
and i am not sure if I can use a 4k2k display Monitor with my Macbook, please help!

Hello, Righten.
Thank you for visiting Apple Support Communities.
I understand that you want to know if your MacBook Pro will support a 4k display. Here is an article that will answer your question.
Using 4K displays and Ultra HD TVs with your Mac
Cheers,
Jason H.

My MacBook pro retina display 15 inch (2013) doesn't start. After I press the start button there is only a beep sound at regular interval. The screen remains blank and the keys don,t light up. Can anyone help please?

My MacBook pro retina display 15 inch (2013) doesn't start. After I press the start button there is only a beep sound at regular interval. The screen remains blank and the keys don,t light up. Can anyone help please?

If your MBP is under warranty, bring it to an Apple store and have the technicians fix it. If not, try the steps in this support article:
http://support.apple.com/kb/ts2570
Ciao.

Does my MacBook Pro Retina Display 13 inch. Late 2013 Supports DDR3 RAM instead DDR3L?

i just bought a brand new macbook pro retina display 13 inches, but i need to now if i can install my 16 gb (8x8 slots) DDR3 memory RAM (Corsair) in to my new computer without any danger or risk for my macbook.

alejandrorg95 wrote:
i just bought a brand new macbook pro retina display 13 inches,
MacBook Pro with Retina display comes standard with 4GB of 1600MHz memory. Please note that the memory is built into the computer, so if you think you may need more memory in the future, it is important to upgrade at the time of purchase.
From here
http://store.apple.com/us/buy-mac/macbook-pro?product=ME864LL/A&step=config

MacBook Pro retina 13" (late 2013, Haswell) why is the highest resolution rendered in 3360x2100, which the system obviously can't handle?!

Hey Apple and Apple users,
I just recently switched from an MacBook Air (mid 2013) to the new Haswell MacBook Pro retina 13" (late 2013 model).
The main reason to do so was the better screen and the option to run higher scaled resolutions, as advertised.
I was willing to trade in the Air's low weight, smaller formfactor and the extra batterylife for the better screen.
When it comes to resolutions:
1280x800 is just a joke nowadays, why is the MacBook Pro still based on it? 13" and 1440x900 work quite fine...see MacBook Air.
1440x900 is okay in everyday life situations, but sometimes you just need "more space" as the third scaling option calls it as well in the display-settings.
1680x1050 on 13" can sometimes be challenging, but it is really fine if you need to work and have a lot UI elements to deal with (Photoshop etc.)
So 1680x1050 scaled on the 2560x1600 screen would be my daily driver for work. So I expected a scaling factor of "1.5238..." (2560/1680) will be used most of the time.
Frankly spoken...I am really disappointed by the 13" retina MacBook Pro and the way OS X Mavericks is handling the scaling.
It obiously works well and responsive with the 1280x800 non-scaling resolution ("best for retina, scaling factor 2: 1280 --> 2560).
Is still "okay-snappy" at 1440x900 (scaling factor 1.777...: 1440 --> 2560).
But it totally breaks down at 1680x1050 (scaling factor 1.523...: 1680 --> 2560).
I use "Mission Control" all the time and it is stuttering and slow...overall a sluggish and unbearable experience.
The same goes for Desktop-Switching by swiping the screens or resizing and moving windows and files around.
So I was wondering why...and then I noticed that when taking a screenshot of my entire screen (CMD + 3) the image size of the screenshot was 3360x2100 and not the expected 2560x1600.
This means Mavericks is not scaling the UI with the appropriate factor (see above). For retina MacBooks it ist simply rendering one pixel of the classic, non-retina Interface in now 4 pixels (2x2) and sending this straight to the screen, which then "scales" it down to the resolution it is able to display.
Why is this bothering me? – Because the machine has to do a lot more work to render the higher resolution that can't even be displayed, due to the screens limitations.
2560x1600 = 4096000 pixels = 100%
3360x2100 = 7056000 pixels = 172%
This means the MacBook has to render 72% more information than actually can be displayed on the built-in screen and are just lost.
Of course this makes the overall UI feel sluggish and idly! Especially with the not that performant Intel Iris IGP and no dedicated graphics card.
All this extra "rendering" just results in a worse battery life due to the extra work that the graphics card and CPU have to do.
First, Apple...are you serious about this?
What can we do about this?
Is there a way to have this properly scaled?
Thanks in advance to everyone.

Okay...I thought deeply about this issue.
Even looking into ways to maybe fixing this on the software side. But it occured to me that this is to deeply embedded into the system that it won't be possbile to come up with a sufficient third-party solution.taht
The problem is that there is no intermediate step inbetween "standard DPI" graphics and "HiDPI" (image-resources named "[email protected]").
But there should be one, to minimize the amount of image information that needs to be processed by the device.
This effects especially the MacBook Pro retina 13", as it has the less powerful Intel Iris IGP, when performing on the highest scaled resolution (equivalent to 1650x1080).
As well as the MacBook Pro retina 15" without a dedicated, second Graphics Unit,when performing on the highest possible scaled resolution (equivalent to 1920x1200).
Those devices don't have enough resources to handle the consequential "HiDPI" resolutions of 3360x2100 for the 13" and 3840x2400 for the 15" model.
(Comment: 3840x2400 = 9,2MP, which is more than the standard 4K resolution of 3840x2160.
I analyzed the scaling factors as follows:
Factor "2" to display 1280x800 on the 13" model and 1440x900 on the 15" model in HiDPI.
Factor "1.777..." would be required to display 1440x900 on the 2560x1600 screen of the 13" model.
Factor "1.714..." would be required to display 1650x1080 on the 2880x1800 screen of the 15" model.
Factor "1.523..." would be required to display 1650x1080 on the 2560x1600 screen of the 13" model.
Factor "1.5" would be required to display 1920x1200 on the 2800x1800 screen of the 15" model.
As all the models seem to have no problem with rendering the intermediate scaling step (1440x900 for the 13" and 1680x1050 for the 15" model) at HiDPI, hence with the scaling factor 2. There is no real need to provide the UI-elements.
But in my opinion there is a strong need for a "MidDPI" ([email protected]) intermediate step for all the UI graphic elements that wis based on the scaling factor 1.5.
This would result in the following:
13" MacBook Pro retina with 2560x1600 screen:
1280x 800 @ 2x = 2560x1600 (no surplus, native screen resolution)
1440x 900 @ 2x = 2880x1800 (the surplus of 1088000px = ~1MP can still be handled and compansated by the weak Iris IGP)
1680x1050 @ 2x = 3360x2100 (the surplus of 2960000px = ~3MP is too much for the weak Iris IGP)
NEW 1680x1050 @ 1.5x = 2520x1575 (with a small border of left=20px, bottom=13, right=20, top=12 pixels, which means ~2,2mm and ~1.3mm around the 1.5x scaled image!).
15" MacBook Pro retina with 2880x1800 screen:
1440x900 @ 2x = 2880x1800 (no surplus, native screen resolution)
1680x1050 @ 2x = 3360x2100 (the surplus of 1872000px = ~2MP can still be handled by the Iris Pro IGP)
1920x1200 @ 2x = 3840x2400 (the surplus of 4032000px = ~4MP can't be handled sufficiently by the Iris Pro IGP)
NEW 1920x1200 @ 1.5x = 2800x1800 (nu surplus, native screen resolution, no border needed!)
The big advantage is that all the graphics have already been remodeled for the HiDPI mode.
So scaling those "factor 2x" images down to "factor 1.5x" should be comparably easy!
Example:
Left: Traditional "standard DPI" icon of "all my files".
Right: "@2x.png" for the "HiDPI" modes.
Middle: "@1.5x.png" suggestions for the "MidDPI" mode; easily scaled down from the lovely HiDPI graphics.
With this simple introduction of the "MidDPI" modes a significant amount of processing power can be saved.
This not only improves battery life when driving those higher scaled resolutions, but also lets the user access those resources for what really matters: processing power for the primary job that the Mac needs to get done.
Thanks in advance.

Macbook Pro Retina 15 late 2013 won't turn on after being sleep

I've been having the an issue with my macbook pro retina 15 late 2013 that I bought 2 weeks ago. After a long time of being slept when I try to turn it on, it won't. I press the power button several times and nothing happens, after a long time of trying then it turns on. and I get the message that the machine turn off because of an error but nothing else. I think that's not ok for such an expensive laptop. I had the first version of the macbook pro retina display and never had an issue like this even though I install a lot of apps from app store and third party apps also. I was running parallels with 3 microsoft windows os and never had an issue like this. In this case I haven't installed anything on my new macbook pro besides parallels and the windows seven os. So I don't know if I should take it to the apple store maybe they could change it for another one I don't know.
Does anyone have the same problem?
sorry for my english

Well I have this problem too, do you get a message saying 'an error has occured please press a button to restart' or something similar when you just brosing the internet or watching a movie.
P.S I use safari and QT.

Anti Reflective coating on macbook pro retina display problems

The AR coating is coming off of my macbook pro retina display. laptop purchased in fall of 2013. anyone else seeing this issue?

You are not the first one. Every laptop with retina display that I know in Latvia has this problem.
Hope that Apple reads such claims and will do something on upcoming models.

Facetime and iMessage on Macbook Pro Retina display slow after Yosemite 10.10.3 Update

Hi
I recently updated my Macbook Pro Retina display to Yosemite 10.10.3 update. I see that the Facetime and iMessage has become relatively very slow. Like for example when someone calls on my phone it takes like more than 15 seconds + to show up on my macbook. Earlier it used to be like instant!
I started seeing this problem on Yosemite 10.10.3 update only. Also the same is the story with iMessage. When I get an SMS or an iMessage from my friends it takes like a good 30 seconds + to show up on my macbook pro.
Just for your information, this is the version of macbook i am using
MacBook Pro (Retina, 13-inch, Late 2013)
2.4 GHz Intel Core i5
8 GB 1600 MHz DDR3
251GB Flash storage
As Suggested by someone I also tried RESETTING my computer's PRAM. That didn't seem to help either. Can anyone help. If it is a genuine bug in Apple Yosemite, I'd like to file a bug in the community.
Regards
Shreyas

Hi Barney,
Here is the output you seek -->
Problem description:
FaceTime takes 30 seconds to open up
EtreCheck version: 2.1.8 (121)
Report generated 19 April 2015 8:13:14 am IST
Download EtreCheck from http://etresoft.com/etrecheck
Click the [Click for support] links for help with non-Apple products.
Click the [Click for details] links for more information about that line.
Hardware Information: ℹ️
    MacBook Pro (Retina, 13-inch, Late 2013) (Technical Specifications)
    MacBook Pro - model: MacBookPro11,1
    1 2.4 GHz Intel Core i5 CPU: 2-core
    8 GB RAM Not upgradeable
        BANK 0/DIMM0
            4 GB DDR3 1600 MHz ok
        BANK 1/DIMM0
            4 GB DDR3 1600 MHz ok
    Bluetooth: Good - Handoff/Airdrop2 supported
    Wireless: en0: 802.11 a/b/g/n/ac
    Battery Health: Normal - Cycle count 430
Video Information: ℹ️
    Intel Iris
        Color LCD spdisplays_2560x1600Retina
System Software: ℹ️
    OS X 10.10.3 (14D136) - Time since boot: 23:47:26
Disk Information: ℹ️
    APPLE SSD SM0256F disk0 : (251 GB)
        EFI (disk0s1) <not mounted> : 210 MB
        Macintosh HD (disk0s2) / : 250.14 GB (111.66 GB free)
        Recovery HD (disk0s3) <not mounted> [Recovery]: 650 MB
USB Information: ℹ️
    Apple Internal Memory Card Reader
    Apple Inc. BRCM20702 Hub
        Apple Inc. Bluetooth USB Host Controller
    Apple Inc. Apple Internal Keyboard / Trackpad
Thunderbolt Information: ℹ️
    Apple Inc. thunderbolt_bus
Gatekeeper: ℹ️
    Mac App Store and identified developers
Kernel Extensions: ℹ️
        /Library/Application Support/Viscosity
    [not loaded]    com.viscosityvpn.Viscosity.tap (1.0) [Click for support]
    [not loaded]    com.viscosityvpn.Viscosity.tun (1.0) [Click for support]
Launch Agents: ℹ️
    [loaded]    com.citrix.AuthManager_Mac.plist [Click for support]
    [running]    com.citrix.ReceiverHelper.plist [Click for support]
    [running]    com.citrix.ServiceRecords.plist [Click for support]
    [loaded]    com.google.keystone.agent.plist [Click for support]
    [loaded]    com.oracle.java.Java-Updater.plist [Click for support]
    [loaded]    com.realvnc.vncserver.peruser.plist [Click for support]
    [not loaded]    com.realvnc.vncserver.prelogin.plist [Click for support]
    [running]    net.juniper.pulsetray.plist [Click for support]
    [loaded]    org.macosforge.xquartz.startx.plist [Click for support]
Launch Daemons: ℹ️
    [loaded]    com.adobe.fpsaud.plist [Click for support]
    [loaded]    com.google.keystone.daemon.plist [Click for support]
    [loaded]    com.macromates.auth_server.plist [Click for support]
    [loaded]    com.microsoft.office.licensing.helper.plist [Click for support]
    [loaded]    com.oracle.java.Helper-Tool.plist [Click for support]
    [loaded]    com.oracle.java.JavaUpdateHelper.plist [Click for support]
    [loaded]    com.realvnc.vncserver.plist [Click for support]
    [loaded]    com.sparklabs.ViscosityHelper.plist [Click for support]
    [running]    net.juniper.AccessService.plist [Click for support]
    [not loaded]    net.juniper.UninstallPulse.plist [Click for support]
    [loaded]    org.macosforge.xquartz.privileged_startx.plist [Click for support]
User Launch Agents: ℹ️
    [loaded]    com.adobe.ARM.[...].plist [Click for support]
User Login Items: ℹ️
    iTunesHelper    Application (/Applications/iTunes.app/Contents/MacOS/iTunesHelper.app)
    AdobeResourceSynchronizer    Application Hidden (/Applications/Adobe Reader.app/Contents/Support/AdobeResourceSynchronizer.app)
Internet Plug-ins: ℹ️
    JavaAppletPlugin: Version: Java 8 Update 31 Check version
    o1dbrowserplugin: Version: 5.41.0.0 - SDK 10.8 [Click for support]
    Default Browser: Version: 600 - SDK 10.10
    net.juniper.DSSafariExtensions: Version: Unknown [Click for support]
    AdobePDFViewerNPAPI: Version: 11.0.10 - SDK 10.6 [Click for support]
    FlashPlayer-10.6: Version: 17.0.0.169 - SDK 10.6 [Click for support]
    Silverlight: Version: 4.1.10329.0 [Click for support]
    Flash Player: Version: 17.0.0.169 - SDK 10.6 [Click for support]
    PepperFlashPlayer: Version: 17.0.0.169 - SDK 10.6 [Click for support]
    CitrixICAClientPlugIn: Version: 11.8.2 - SDK 10.7 [Click for support]
    googletalkbrowserplugin: Version: 5.41.0.0 - SDK 10.8 [Click for support]
    AdobePDFViewer: Version: 11.0.10 - SDK 10.6 [Click for support]
    QuickTime Plugin: Version: 7.7.3
    SharePointBrowserPlugin: Version: 14.4.9 - SDK 10.6 [Click for support]
    MeetingJoinPlugin: Version: Unknown - SDK 10.6 [Click for support]
Safari Extensions: ℹ️
    ClickToFlash
    Reload Button
    YoutubeWide
3rd Party Preference Panes: ℹ️
    Flash Player [Click for support]
    Java [Click for support]
    MacFUSE [Click for support]
Time Machine: ℹ️
    Time Machine not configured!
Top Processes by CPU: ℹ️
        18%    mds
        15%    Safari
         6%    WindowServer
         5%    com.apple.WebKit.Networking
         1%    ocspd
Top Processes by Memory: ℹ️
    455 MB    softwareupdated
    206 MB    Microsoft Outlook
    153 MB    com.apple.WebKit.WebContent
    146 MB    WindowServer
    137 MB    Safari
Virtual Memory Information: ℹ️
    298 MB    Free RAM
    3.76 GB    Active RAM
    3.36 GB    Inactive RAM
    1.17 GB    Wired RAM
    4.45 GB    Page-ins
    901 KB    Page-outs
Diagnostics Information: ℹ️
    Apr 18, 2015, 08:25:23 AM    Self test - passed
    Apr 17, 2015, 06:29:29 PM    /Library/Logs/DiagnosticReports/ncproxyd_2015-04-17-182929_[redacted].crash
    Apr 17, 2015, 03:11:05 PM    /Library/Logs/DiagnosticReports/com.apple.WebKit.WebContent_2015-04-17-151105_[ redacted].cpu_resource.diag [Click for details]

Photoshop CS5.1 Pixelated on Macbook Pro Retina Display

Hello!
I am a photography student who just bought a new macbook pro retina display. I use Photoshop a lot for my course so need help with this as quick as possible.
Everything on Photoshop seems to be pixelated which is not ideal right now. I also have an iMac which runs the same version of Photoshop and that is absolutely fine, never had a problem. My friend suggested downloading a trial version of the CC as this automatically sorted hers out but did not mine. Any suggestions at all will be SO helpful as I've researched into this problem and are yet to find an answer!

Very simple. The hiDPI Macintoshes and MacOS support for same were released after CS6 was released. Some of the CS6 applications got upgrades to support these hiDPI displays; others including InDesign did not get such upgrades until the CC 2013 version.
Sorry, but there is not anything you can do about this with CS5-vintage software.
- Dov

Macbook Pro Retina Display (Oct 2013)

Similar Messages

Maybe you are looking for