Macbook pro (snow leopard) will not boot after software update

I helped my mom buy a Macbook Pro for herself for Christmas. Today, I connected it to her old eMac and used the migration assistant to transfer files over. It was unable to estimate migration time on the only user (after 45 minutes) so I didn't migrate the user. Then I tried to pair her macbook to her new bluetooth keyboard, but no magic happened, so I tried to use the bluetooth setup assistant, which crashed. So I ran a software update, hoping that this would fix whatever the bluetooth problem is. Despite having updated on the 23rd, there were 4 updates. None seemed applicable but I installed them anyway. Now the computer won't boot at all.
Software update said that I had to restart for the updates to take effect, so I restarted. The harddrive went whirrrrrr and the grey screen with the apple logo and the spinning circle displayed. Then the harddrive stopped going whirrrr and 10 minutes later, I started looking on the support site for what to do. I found this:
http://discussions.apple.com/thread.jspa?messageID=10564149&#10564149
Per the instructions in the last post, I fscked the drive (although -f, in accordance with the fsck help). This found no problems. The next suggestion was to boot from the OSX install disk. Only one problem-- there was a disk in the disk drive when the problem occurred and the disk eject button apparently only works while in the gui. I can't install from disk if I can't get the existing disk out of the drive.
So, any other ideas on what I can do to get this machine to boot?
Message was edited by: jenlarkin

Hi Jen:
Since it's new, you're entitled to 90 days of phone support (3 years if you buy AppleCare). It sounds to me like you may have some hardware issue(s) going on - you should not have the sorts of issues you're having with a new Mac. Apple will probably be much better and faster about getting you fixed than this board may be able to if that is the case.

Similar Messages

MacBook Pro will not boot after software update

MacBook Pro will not boot after doing an Apple Software Update (of course they will not help you). MONEY, MONEY, MONEY is the name of the game. They can cause your computer to crash and still charge you!
Does anyone have an answer to why my computer is showing a little gear spinning for hours? I have tried several things with NO luck.
Thanks-

Run through the list of fixes here
Step by Step to fix your Mac

Snow Leopard will not boot after TM Restore

I had an email issue (lost 5 accounts) that has turned into a nightmare. Apple Support told me to restore my entire hard drive from my Time Machine. I booted to the DVD and selected a restore point and 12 hours later I get the Apple with the spinning wheel. I have tried two restore points - same result. It will not boot in safe mode either. I ran the Verify Drive utility and the drive checks out.
The drive is about 75% full after this TM restore operation so it appears it is pulling all of my data into the machine.
I have a number of backups of my system including a full one on ARQ plus all the TM backups. I am just not versed in the Apple OS enough to know how to recover from this point.
Q's:
1. Is it possible that the data and the Apps have been restored but the OS is simply corrupt on the TM?
2. Is there a Repair feature on the SnoL DVD or am I faced with a fresh install?
3. If I do a fresh install, can I simply copy the Apps folder back in the machine and my apps work correctly? (I realize a few may not that have to have components in browsers or whatever).
Suggestions on recovery approach...
Thanks, Uursa

uursamajor1 wrote:
1. Is it possible that the data and the Apps have been restored but the OS is simply corrupt on the TM?
Welcome to Apple's discussion groups.
That's possible. Once you can get it to boot you can explore that.
2. Is there a Repair feature on the SnoL DVD or am I faced with a fresh install?
Soon after booting from that DVD you should see a Utilities menu with Disk Utility under it. With Disk Utility you can perform a "Repair Disk" operation.
3. If I do a fresh install, can I simply copy the Apps folder back in the machine and my apps work correctly?
You could first try installing OS X 10.6 over what's already there. You might also learn more about what's wrong by doing a "verbose boot':
http://support.apple.com/kb/HT1492

My MacBook Pro Snow Leopard will not shut down.

When I try to shut down my MacBook Pro it goes as far as the spinning wheel on the blue screen and will not complete the shutdown. I have to hold the power button to shut down completely.
Both disk and permission repair does not solve the problem.
Help please.

I had the exact same problem, the only way for me to fix it is to delete everything off your mac, or backup your data and reinstall the OS, but just reinstalling the OS won't fix it, back up your data (if you want to keep it) and then erase everything off your mac then put your data back in. Hope it helps.
Thomas

I have a MacBook Pro 15" and my warranty just ran out! I partitioned my harddrive into two partitions, one with Snow Leopard and the other with microsoft.This morning I turned on my Macbook Pro and it will not boot into Snow Leopard.

Good Morning,
I have a MacBook Pro 15" and my warranty just ran out! I partitioned my harddrive into two partitions, one with Snow Leopard and the other with microsoft.This morning I turned on my Macbook Pro and it will not boot into Snow Leopard. I shut it off took out the battery, reinstalled the battery. Then I put in the Snow Leopard CD and booted up to disk utility and The Snow Leopard partion would not show up?? I do see the microsoft partion.
I also rebooted holding down the shift key and still no Snow Leopard
Could you please tell me what I can do, what keys do I press on restart any advice to get Snow leopard back.
thank you.

Have you restarted holding down the Opt key? That procedure should give you a gray screen with all of the partitions that exist. Then select the SL partition for boot. Also go to System Preferences and Startup Disk, unlock the lock and select the SL partition as the default boot partition, then relock.

Install Disk for Snow Leopard will not boot on an iMac 27in

My Install Disk for Snow Leopard will not boot on my iMac 27in. The Apple Logo is the only thing the user will see. The current OS on the system is 10.6.6. Upon placing the Snow Leopard DVD in the system, the DVD players spins for a few seconds and displays the Apple Logo. Nothing happens after 20 minutes.

Yes, it is ridiculous how it is impossible to install Snow Leopard. I have two Snow Leopard DVDs: one that I purchased for a Macbook soon after it's release (10.6.0), and one that came with my iMac (10.6.4). Both of these boot up my Macbook (running 10.6.7) just fine. My SL 10.6.0 DVD mounts onto my iMac (Lion 10.7.0), but you cannot run the install. I attempted to boot from this DVD and got the infinite white screen and Apple logo, as some have reported above. The other SL 10.6.4 DVD will not even mount in Lion, and will not even show up as a bootable drive when I attempt to select it after holding alt/option on reboot.
I created a bootable external drive from SL 10.6.0, attempted boot, same infinite white screen/apple logo.
I created a bootable external drive from SL 10.6.4 on my macbook. I attempted to boot from this drive, and got the white screen of death, except that this time I actually got the loading symbol underneath the Apple logo. After about a minute of attempting to boot, the Apple logo changed to a circle with a diagonal line through it (the "NO!" sign).
I took my iMac to the genius bar. They inserted SL 10.6.0, which would not boot. Then they determined that my computer had to run 10.6.4 and later. So, they restored an image of SL 10.6.4 onto my partition (not an install from an image, but an image of SL already installed). Hurray! Snow Leopard was successfully shoved onto my iMac!
I then deleted a third partition on my hard drive I did not need anymore, which somehow screwed up my SL partition (even though it said "Will not erase partition SL or Macintosh HD). Now I am back at square one, and I guess I need to take my flippin iMac back to Apple for them to do what I should be able to do.
I like Apple, but sheesh do I hate Lion right now.

My early Intel iMac running Snow Leopard will not boot past the apple logo. I have tried holding the c key and inserting the install disk, but nothing. What do I try next?

My early Intel iMac running Snow Leopard will not boot past the apple logo. I have tried holding the c key and inserting the install disk, but nothing. What do I try next?

I have tried resetting PRAM and all other items listed in the Apple support site. This happened after an update to iTunes was added. Also this is happening to other people. Please help.

My macbook pro running lion will not boot . it stays on the grey page with the cog spinning. I have tried all methods of booting to no avail. I have removed the bottom and taken out the battery and the ram . will this affect my applecare warranty.

my macbook pro running lion will not boot . it stays on the grey page with the cog spinning. I have tried all methods of booting to no avail. I have removed the bottom and taken out the battery and the ram . will this affect my applecare warranty. I had to try myself as I'm overseas for two months and nowhere near any sort of help .

there was a recent software update that seemed to screw HDV up. Do some searching here over the last month or 2 and you'll find a bunch of posts and some possible solutions.
Worst case scenario, do as Shane suggests. But might I suggest you take a look at the user tips section of the forum. there are some great tips on how to prevent these sorts of problems by cloning your startup drive, etc.

My ipod touch gen 4 will not recovery after software update. have tried everything. device not recognized by itunes. any ideas?

my ipod touch gen 4 will not recovery after software update. have tried everything. device not recognized by itunes. any ideas?

Try:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar

Mac Mini will not boot after Security Update 2008-007

Hello,
A G4 Mac Mini machine I was asked to take a look at will not boot after the owner (succesfully) installed Security Update 2008-007 from Software Update. Booting always hangs at the blue screen after the Apple logo, and booting in verbose mode reveals that WindowServer is crashing repeatedly. Permissions and filesystems have been repaired, PRAM reset, etc. Safe boot also exhibits the same problem, but it is possible to boot to single user mode. Hardware checks out fine with diagnostic utilities.
Any suggestions on how to fix this? Unfortunately, backups are not available (it's not my machine =).

Hi Arkku , and a warm welcome to the forums!
I'd certainly give Sig's advice a try first.
If that should fail...
applesetupdone...
This was Posted by: JoseAranda at September 9, 2006 3:48 AM
"OK, restart your computer, hold down Command-s and type in the following:
/sbin/fsck -fy Enter
/sbin/mount -uaw Enter
rm /var/db/.applesetupdone Enter
# The rm command is the remove command which deletes the file.
# Robert: I'd rename the file via: mv /var/db/.applesetupdone /var/db/.applesetupdone.old
reboot Enter
Once you've done that the computer reboots and it's like the first time you used the machine. Your old accounts are all safe. From there you just change all other account passwords in the account preferences!!
end of posted by: JoseAranda"
Reset OS X Password Without an OS X CD...
http://theappleblog.com/2008/06/22/reset-os-x-password-without-an-os-x-cd/

HP Pavilion 15-n268sa will not boot after windows update (windows 8.1)

After a series of windows update (windows 8.1) my HP Pavilion 15-n268sa will not boot up, no fan noises, no lights no nothing.
I have tried a "hard reset" a number of times with no success.
When the battery is present the white LED flashes 3 times when the power button is pressed.
Please please help.

Hello Cuffy,
Welcome to the HP Forums!
I understand you notebook will not boot after a series of Windows updates.
Can you tell me if you are able to access the HP Recovery Manager by repeatedly tapping the F11 key while the notebook turns on? If you can access this, try doing a system restore to before you installed the updates. If not I would suggest you go through this document: Computer Does Not Start and the LEDs Blink or the Computer Beeps.
If it's the Caps Lock light that is blinking this document will tell you exactly what the error is (spoiler: 3 beeps is a memory failure). This could also explain the failed updates. The updates are stored in the RAM before being applied to the operating system.
You can try reseating the RAM, or using only 1 of the RAM cards, as you have 2x4GB cards. If it still doesn't work with 1 card, try the other card to confirm it has failed.
You can replace defective cards via HP Phone Support if covered under warranty or at the HP Part Store if not covered. You can contact HP Technical Support at 1-800-474-6836 in North America. For all other regions click here.
Hopefully this information helps!
Please click the "Kudos, Thumbs Up" at the bottom of this post if you want to say "Thanks" for helping!
Please click "Accept as Solution" if you feel my post solved your issue, it will help others find the solution.
The Great Deku Tree
I work on behalf of HP.

Macbook Pro 10.6 will not boot

Last night I had a kernel panic. When the system tried restarting it stuck on the grey/blue screen with the Apple logo and spinning wheel. I have tried booting in safe mode: same screen. I have booted with my OSX install disk and run a disk repair, which said the volume was fine. I ran a permissions repair which had errors, but they were the ones that Apple says you can ignore. From here I could not swich to my MacHD drive for start up (bless problem?)I have run a hardware test with my OSX install disk and it says there are no problems with any hardware. I cannot reinstall OSX with disk onto my hardrive as it finds a problem. I cannot erase my harddrive because it now will not unmount. Hoping there is a fix to all of this?? I feel like I have done everything that I have found in the forums with others' related problems. If anyone has ideas, please help. I am checking this forum using my phone and an HP (yikes!)

Reinstall OS X without erasing the drive
1. Repair the Hard Drive and Permissions
Boot from your Snow Leopard Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer.
If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
2. Reinstall Snow Leopard
If the drive is OK then quit DU and return to the installer. Proceed with reinstalling OS X. Note that the Snow Leopard installer will not erase your drive or disturb your files. After installing a fresh copy of OS X the installer will move your Home folder, third-party applications, support items, and network preferences into the newly installed system.
Download and install Mac OS X 10.6.8 Update Combo v1.1.

My macbook pro Mod A1261 will not boot. It goes to the gray death screen

When I try to boot my macbook Pro it goes to the gray screen of death (to borrow a term fmor the PC world). It will not boot in safe mode. It did this before and I though I had gotten it fixed but I guess not. Any suggestions?
Bill

If you look to the right there are so many examples of the same symptoms - just read them, study them, and see if the solutions about 'Safe Mode' 'Recovery Mode' 'Disk Repair' can solve the issue. After that do report back

Macbook pro running,lion will not boot

My mac book,pro running lion will not complete the start up/boot have tried single user boot, and command v any ideas

I had the same problem... I was downloading the latest update (whatever it was for, I forget at this point)...
I was really frustrated because I have never had to troubleshoot my MacBook Pro (early 2008 or whatever was before the black bevel/chicklet keyboard), plus I was running Lion, so I did not know how to do any recovery.
Cmd + R worked like a charm. Repaired my disk, repaired my permissions, then reinstalled (or restored) Lion... now my computer is actually running better than before!
The Disk Repair feature in Lion works magic!

Satellite Pro L300 will not boot after Bios update

Help please.
I have just formated a Satellite Pro L300 laptop.
I used all the updated drivers from Toshiba and all went very well.
I then updated the bios with the latest version.
After doing this the laptop will not boot but just keeps scrolling through the start menu and no matter what option I choose it just keeps doing the same thing.
Any ides welcome

Hi
I used the Microsoft installation disk but just keep getting to the same stage until the blue screen appears. I have tried different installation disks and also changed the hard drives as well. I can do everything in bios, change boot device enable or disable devices but that is it. I have tried a few times to instal windows but it just stops at the same point saying windows is stopping instal to protect the system. I fear the bios update has done some permanent damage as I cant get past the dreaded blue screen.Thanks anyway

Macbook pro (snow leopard) will not boot after software update

Similar Messages

Maybe you are looking for