Macbook Pro starting problem
I have a massive problem, thanks in advance if some one can help.
I have a mac book pro 15 inch mid 2010 with the latest operating system.
when i start the the computer i get the screen attached as a photo then a black screen and then it turns off and it just keeps doing that over and over again, till i push the power button for 10 sec then it turns off..
I have tried the following:
reset pram
starting in safe mode
starting in recovery mode but it won't do it.
i a few other key combinations that i found on the internet.
has anyone got any ideas on what to do next ??
You have the MacBookPro6,2—the Edsel of Macs. It may have the logic-board defect that was covered by this recall.
Make a "Genius" appointment at an Apple Store, or go to another authorized service provider, to have the machine tested. The routine hardware diagnostics used by service providers do not detect the fault. There is a specific test for this issue that Apple calls "VST" (for "Video Switching Test.") Ask for it. A "Failed" result means that the fault is present. However, according to reports, some units may pass the test, and yet still be deemed eligible for repair under the program. Your experience may vary.
Note that the recall only applies within three years of purchase. After that, Apple may refuse the service. In that case, you may be quoted a price of about $300 (in the U.S.) for a "depot repair," which involves shipping the unit to a central repair facility and takes about two weeks. For that flat fee, anything found wrong with it should be fixed, not just the logic board.
The model was discontinued on February 24, 2011, so the recall has nominally ended. Some units may have been sold after that date by Apple as refurbished, or by resellers as new, and they might still be covered.
Some owners report that their unit was repaired under the program after the deadline had passed. Others report that the repair was covered by the extended warranty from a credit-card issuer. Again, your experience may vary.
Sometimes the replacement part is also defective, so be prepared for that possibility. If you decide to pay for a new logic board, test thoroughly during the 90-day warranty period on the repair. Some owners have reported that they went through as many as three replacement boards before getting one that worked.
If you're dissatisfied with Apple's response, please keep in mind that no one here represents the company or can help with customer-service issues.
Similar Messages
-
Macbook pro starting problems: on off loop when turning on
Hello apple community.
my macbook pro when i press the power button it turns on, the white light at the corner goes on, and i can hear the fans spinning,
but then immediately it turns off, and then goes on by itself again and goes off,on off,onoff.... into a continuous on off loop. the screen stays black all the time during this. no apple logo
what can this be? i tried reseting the ram chips in their socets but it did not help.
I hope you can help me.Hi Jeffcur,
Welcome to the Support Communities!
The article below may be able to help you with this issue.
Although the title doesn't match your issue, this article has several troubleshooting steps for startup issues in general.
Mac OS X: Gray screen appears during startup
http://support.apple.com/kb/ts2570
Cheers,
- Judy -
My Macbook Pro started running really slow
This week my Macbook Pro started running super slow, taking ages to open programs and giving me the color wheel alllll the time. I've never had problems like this before! I'm not running many applications or doing anything unusual but it's just running extra slow. Once or twice it has also totally gone to sleep while I was in the middle of using it, and I had to wake it back up. It has also been getting really hot and the battery life seems worse...! This is all new, I'm using my computer just as I always have but it suddenly has issues.
The only thing it has been doing for a while is sometimes the screen will go blue - this either corrects itself within a few seconds or if I close my Macbook and then reopen it, the screen is back to normal. This is very rare though and I don't know if it's related to the slowness problem.
What can I do to fix this??
Mac OS X 10.6.8
2 GHz Intel Core i7
4 GB 133 MHz DDR3
I just ran EtreCheck -
Hardware Information:
MacBook Pro (15-inch, Early 2011)
MacBook Pro - model: MacBookPro8,2
1 2 GHz Intel Core i7 CPU: 4 cores
4 GB RAM
Video Information:
AMD Radeon HD 6490M - VRAM: 256 MB
Intel HD Graphics 3000 - VRAM: 384 MB
System Software:
Mac OS X 10.6.8 (10K549) - Uptime: 1 day 3:59:13
Disk Information:
Hitachi HTS725050A9A362 disk0 : (465.76 GB)
(null) (disk0s1) <not mounted>: 200 MB
Macintosh HD (disk0s2) / [Startup]: 465.44 GB (235.1 GB free)
MATSHITADVD-R UJ-898
USB Information:
Apple Inc. Apple Internal Keyboard / Trackpad
Apple Inc. BRCM2070 Hub
Apple Inc. Bluetooth USB Host Controller
Apple Inc. FaceTime HD Camera (Built-in)
Apple Computer, Inc. IR Receiver
FireWire Information:
Thunderbolt Information:
Apple, Inc. MacBook Pro
Kernel Extensions:
com.digidesign.iokit.DigiDal (8.0.3f1)
com.paceap.kext.pacesupport.snowleopard (5.7.2)
Startup Items:
DigidesignLoader: Path: /Library/StartupItems/DigidesignLoader
M-AudioFastTrack: Path: /Library/StartupItems/M-AudioFastTrack
PACESupport: Path: /Library/StartupItems/PACESupport
Problem System Launch Daemons:
[System] org.samba.winbindd.plist 3rd-Party support link
Launch Daemons:
[System] com.adobe.fpsaud.plist 3rd-Party support link
[System] com.google.keystone.daemon.plist 3rd-Party support link
[System] com.microsoft.office.licensing.helper.plist 3rd-Party support link
[System] org.eyebeam.SelfControl.plist 3rd-Party support link
[System] PACESupport.plist 3rd-Party support link
Launch Agents:
[System] com.google.keystone.agent.plist 3rd-Party support link
[System] com.hp.help.tocgenerator.plist 3rd-Party support link
[System] com.m-audio.mobilepremkii.helper.plist 3rd-Party support link
User Launch Agents:
[not loaded] com.apple.CSConfigDotMacCert-[...]@me.com-SharedServices.Agent.plist
[not loaded] com.facebook.videochat.[redacted].plist 3rd-Party support link
[not loaded] com.spotify.webhelper.plist 3rd-Party support link
User Login Items:
Flux
iTunesHelper
RescueTime
Internet Plug-ins:
o1dbrowserplugin: Version: 5.2.4.18058 3rd-Party support link
Unity Web Player: Version: UnityPlayer version 3.5.2f2 - SDK 10.6 3rd-Party support link
RealPlayer Plugin: Version: Unknown
Silverlight: Version: 5.1.20913.0 - SDK 10.6 3rd-Party support link
FlashPlayer-10.6: Version: 12.0.0.77 - SDK 10.6 3rd-Party support link
QuickTime Plugin: Version: 7.6.6
Flash Player: Version: 12.0.0.77 - SDK 10.6 3rd-Party support link
googletalkbrowserplugin: Version: 5.2.4.18058 3rd-Party support link
SharePointBrowserPlugin: Version: 14.3.9 - SDK 10.6 3rd-Party support link
AdobePDFViewer: Version: 10.1.1 3rd-Party support link
iPhotoPhotocast: Version: 7.0 - SDK 10.7
JavaAppletPlugin: Version: 13.9.8 - SDK 10.6 Outdated! Update
iTunes Plug-ins:
Quartz Composer Visualizer: Version: 1.2
3rd Party Preference Panes:
Flash Player 3rd-Party support link
Growl 3rd-Party support link
M-AudioFastTrack 3rd-Party support link
M-Audio MobilePre 3rd-Party support link
Old Applications:
None
Time Machine:
Time Machine information requires OS X 10.7 "Lion" or later.
Top Processes by CPU:
7% firefox
3% WindowServer
3% EtreCheck
2% hidd
0% coreservicesd
Top Processes by Memory:
397 MB firefox
106 MB mds
82 MB WindowServer
82 MB Mail
49 MB quicklookd
Virtual Memory Information:
1.04 GB Free RAM
1.04 GB Active RAM
1.03 GB Inactive RAM
907 MB Wired RAM
467 MB Page-ins
0 B Page-outsThe startup drive is failing, or there is some other internal hardware fault. The "etrecheck" output is irrelevant.
Back up all data on the drive immediately if you don't already have a current backup. There are ways to back up a computer that isn't fully functional — ask if you need guidance.
Make a "Genius" appointment at an Apple Store, or go to another authorized service provider.
If privacy is a concern, erase the data partition(s) with the option to write zeros* (do this only if you have at least two complete, independent backups, and you know how to restore to an empty drive from any of them.) Don’t erase the recovery partition, if present.
Keeping your confidential data secure during hardware repair
Apple also recommends that you deauthorize a device in the iTunes Store before having it serviced.
*An SSD doesn't need to be zeroed. -
my macbook pro started acting strange after a safari reset.
the mouse no longer: animates the dock, activates hot corners or selects pages from safari 'top sites' (without a hassle). attempts to reset dock and hot corners from preferences has been fruitless
the mouse also gets 'stuck' in logic precipitating force quits.
i run osX 10.6.8 on a 2007 macbook pro that has had 2 motherboards replaced autumn 2010.
my troubleshooting has been: restart, pRam and safe boot, also checking a 'test' account to find the same issues extant.
pRam restart caused airport to quit and say there is no airport card, and wouldn't respond untill another reboot.
macbook pro 15" 2.4 GHz intel core duo.2 GB 667 MHz DDR2 SDRAM.
i have treated this book with care, yet run logic pro studio to the limit of this book's abilities.
what shoud i do?You don't say which year you have, however...
...there are known problems with the mid-2010 models (see http://support.apple.com/kb/TS4088?viewlocale=en_US&locale=en_US) as well as early and late 15" 2011 models (see https://discussions.apple.com/thread/4766577?tstart=0).
Apple has taken ownership of the problems with the 2010 model but, unfortunately, the free logic board replacement for that model has probably long expired for you - three years after date of purchase.
One the 2011 models Apple has admitted no defect. You'll just have to skim the articles to get an overview of the problems that people are having (usually showing up as screen glitches at first and then going downhill from there).
Good luck,
Clinton -
Hi. Over the last few days i have been having problems with my MacBook Pro starting up. If i put it to sleep it will not wake up, just get a blank screen and if i turn it off, it will not boot. I can hear the drive spin up, the chime sounds, but just get a blank screen. The apple logo is not illuminated and the caps lock key illuminates when pressed. The only way to get it to boot is to turn it off and on repeatedly around 30 times and then itll boot up and work fine. My battery was pretty bad so thought this might be the cause but after replacing it, its still the same. Its running 10.8.2 and i think its a late 2010 MacBook?
The folder / question mark means that the system is either not on the startup disk you're using, or has been damaged.
If you can't boot from your original hard drive (you may need to press the Option key while booting to select a startup disk), try booting from your install DVD (hold C while starting up). Option will not show drives or partitions that don't have a bootable system on them (it can, however, show a drive with a damaged system that will, when tried, yield the ? and folder icon.)
You should then be able to run disk repair or switch back to your original startup disk so you can move some "stuff" to an external drive. -
So, about a week ago my macbook pro started having lots of issues: wifi connectivity, slow performance, sound issues, spotlight wasn't working. After going through the issues with apple support, they decided the best course of action was to erase the hard drive and do a reinstall. Since I have a recent backup this seemed like a good enough option. They were kind enough to send me a copy of the snow leopard disk to do the install since we couldn't get it to complete through the disk utility. Not sure why, since it says we are fully connected, it just never completed.
Anyway, so now that you have the background here is the new issue. The macbook pro keeps spitting out the disk I'm trying to install from. Disk utility and using the 'Startup Disk' function from the apple menu doesn't read the disk.
Can anyone suggest a solution to this vexing problem?
Thanks in advance.Jeremy.Laurin,
have you tried agb76’s approach here? -
Every time I watch a video on youtube (on any browser) my macbook pro starts freezing
Hello everyone,
Every time I watch a video on youtube (on any browser) my macbook pro starts freezing half a minute, works fine for 10 seconds, then freezes again... This started a couple days ago. The only solution is to restart and not watch video's... Anyone know how to solve this?
I have a pretty old macbook pro, from around 2006. I've never had this problem...
Thanks,
Tommy
P.S. My family is currently deleting some items and it seems to be working, I'll update you if the problem is fixed.Reinstall Flash Player? YouTube is Flash based.
-
My MacBook Pro started running very slow. I did disk utility/repair
My MacBook Pro started running very slow. I did disk utility/repair and it helped but still very slow. Repair gave me this message, "SUID file 'System/Library/CoreServices/RemoteManagement/ARDAgent.app/Contents/MacOS/ARDAg ent has been modified and will not be repaired." Any suggestions on this message and/or what else I can do to get my computer back to the way it used to run? Thank you!
It says 199.15 GB free of 499.25 GB. Can I remove the Remote Management program to solve the other unrepairable problem?
-
Macbook Pro starts up, has a small loading bar, and then shuts off.
Macbook Pro starts up, has a small loading bar, and then shuts off after a few seconds, but the Windows bootcamp partition works fine.
The repair disc option (using install disc) failed, and the computer cannot locate the original Mac side partition. Only Bootcamp appears under options to "restore from backup" or reinstall. The repair disc options says it should be repaired but doesn't seem to know how.
Macbook Pro.
Snow leaopard
Bootcamped with Windows.
Any ideas?Hold c or option key and boot off the 10.6 installer disk, run DU Repair from there.
run through this list of fixes 1-8
Step by Step to fix your Mac
If it doens't work, you can recover files if you don't have any current OS X file backups, then grab what you can out of Bootcamp
Use Data Rescue installed on the extenral boot drive ($100) to read the bits of the internal (non-filevaulted) drive to retrieve OS X data files if you can't get them off manually via drag and drop methods.
Create a data recovery, undelete boot drive
If you want to clone Windows, use WinClone and another drive. However it's likely compromised, unless it something you did in Windows, like trying to create a new parttition perhaps?
Then perform a Zero Erase and install of 10.6 as shown here (on the entire drive, not only the parittions), this will give a new GUID partition table, EFI and map off bad sectors, totally fresh everything.
How to erase and install Snow Leopard 10.6
You cna use Carbon Copy Cloner to clone the new extenral setup to the new scrubbed internal drive. Recreate Bootcamp and WinClone back or fresh install Windows into Bootcamp like before. OR opt to use virtual machine software which is safer.
Windows in BootCamp or Virtual Machine?
Windows 7 can write to the boot drives GUID partition map (unlike XP), this is likely why it's borked now. -
I install windows 8 in my macbook pro, the problem is it cannot detect wifi connection and bluetooth, because when i click the wireless in settings there are no choices... but when i use the mac os, everything is fine, the wifi, the bluetooth everything is functional, can you help me fix this problem? help will be much appreaciated.. thanks
How did you install Windows? Did you use Bootcamp Assistant or did you use a virtual machine like Parallels, Fusion, or VirtualBox.
If you used Bootcamp Assistant, did you download and install the Windows Support software (drivers) in accordance with the Bootcamp instructions? -
I wanna reinstall Mac OSx lion on MacBook pro, my problem is I dint purchase OSx lion with my apple Id before.so anybody can tell me how to purchase OSx with my apple Id on MacBook
Nope. You can purchase a Snow Leopard DVD for $29.00 through an Apple retailer or ordering from AppleCare:
Apple Store Customer Service at 1-800-676-2775 or visit online Help for more information.
To contact product and tech support visit online support site. -
MacBook PRO 17'' Problem?
MacBook PRO 17'' Problem?
I bought in America a new Macbook Pro with me already 8mj:
Model Identifier: MacBookPro4, 1
Processor Name: Intel Core 2 Duo
Processor Speed: 2.5 GHz
Number Of Processors: 1
Total Number Of Cores: 2
L2 Cache: 6 MB
Memory: 2 GB
Bus Speed: 800 MHz
Boot ROM Version: MBP41.00C1.B03
SMC Version: 1.28f1
GeForce 8600M GT 512mb GeForce 8600M GT 512MB
Type: DDR2 SDRAM 2 pieces
Size: 1 GB
Speed: 667 MHz Speed: 667 MHz
sometimes my ignition pocme blow 2puta quickly and fit 1s and thus prove it does not poweroff, the display has no image.
or when booting the mistake occurs in the image:
sometimes when booting the error as shown in the picture!
but more frequently happens that does not powered up LCD! ONLY PROVIDES NOTICE ACOUSTICAL 2puta quickly and fit 1s, etc. ...
When it poweroff so again uplalim all work properly and I do not have any more problems! After re-ignition occurs again, the same situation!
I have made a hardware test and reinstalira OS X Leopard 10.5.6 Update! but again the same story, says that everything ok!
There is no additional peripherals except that I ordered from the apple store to upgrade my 1G still working memory SDRMA 667MHz
Thank you prayed that we would help someone because I do not know whom to turn to more ...
IMAGE: http://www.mackorisnik.com/forum/download/file.php?id=747
All details of problems in URL: http://www.mackorisnik.com/forum/viewtopic.php?f=7&t=6116Your system profile is a complete blank!!
When posting in Apple Communties/Forums/Message Boards.......It would help us to know which Mac model you have, which OS & version you're using, how much RAM, etc. You can have this info displayed on the bottom of every post by completing your system profile and filling in the information asked for.
CLICKY CLICK-----> Help us to help you on these forums
***This will help in providing you with the proper and/or correct solutions.***
If you are still under warranty and/or have AppleCare, call them. Let them deal w/it. -
iPhone music will not respond to Play button after being paused.
The same music is on my iPad and MacBook Pro without problems. Any suggestions about cause and solution.Do a
Reset: Hold down the Sleep/Wake button and the Home button at the same time for at least ten seconds, until the Apple logo appears. Note: You will not lose any data -
My MacBook Pro starts then shuts down on its own 4 seconds later. An idea on what I should do? Thanks!
Is the little LED on your adapter's MagSafe plug glowing when it's connected? What color?
It sounds as though your battery is drained and the adapter isn't charging it. Try resetting the SMC:
http://support.apple.com/kb/HT3964
That may start the battery charging again. -
My MacBook Pro starts and shuts off after loading for sometime
My MacBook Pro starts and shuts off after loading for sometime
Try starting in Safe mode by holding down the Shift key while booting. Safe mode takes a while to load the OS. After that, restart the computer normally.
If that does not work, start up in Recovery by holding down the Command and R keys. In the window that opens, choose Disk Utility at the bottom and verify and repair your disk. Repair permissions while you are there.
Maybe you are looking for
-
Installation problem in solarise 9.
Hi I am installing solarise 9. in my system My system configration is INTEL P4 3.0 Ghz/ 1 GB RAM /80 GB IDE HDD But is giving a problem Problem is entering boot debuger 13bd7f: This error is comming pls give me sugeestion . SATYA
-
Hi, It's been several nights that I have a dozen kernel panic on my Mid 2012 Mac Pro and during the day there is no problem. I'm hoping someone can help me identify what may have caused it. Thanks for looking: Processor 3.33 GHz 6-Core Intel Xeon Me
-
Which midi device is better to use in windows (soundblaster X-FI)
there are 3 MIDI devices to select in windows: 1---sint SW wave GS (windows) 2---SB X-FI SYNTH A [E800] 3---SB X-FI SYNTH-B [E800] (default after installed creative drivers) personally I have selected (sint SW wave GS) because is louder but I'm not s
-
please help here i just interrupted the process of erasing all content from my ipod it took almost 10 hours then i got worried from waiting i pressed both sleep button and menu button for 10 seconds while in process what should i do?
-
How to get bex query changes reflected in webi.
Hi expert, I am using sap bex query in WEBI by BICS connection, but I have done some change in bex query, how can I get those changed reflected in webi. Many Thanks,