Macbook pro stuck on boot

I just buy my macbook pro 1 month ago, im a new user. my macbook pro wont boot up and after 30% loading on startup, it suddenly shut down. why? can someone help me? i dont know what to do

You have a startup problem. Most likely with a startup item. Here are some things you http://www.macworld.co.uk/news/mac/steps-take-when-your-mac-wont-start-3423817/can try.

Similar Messages

Macbook Pro stuck on boot-up screen

When I woke up this morning, I found that my Macbook Pro has turned off while I was sleeping (I have it on constantly for convinence sake because it takes to darn long to boot-up), So I didn't think about it. Untill I found out that it would not boot on. Let me explain what happens
1) Presses power button
2) No boot-up sound
3) Loads up Apple logo
4) Shows update bar and loading wheel at bottom of the screen
5) After a few seconds, the bar dissapears.
6) After a second or two, the wheel stops turning.
7) Macbook Pro boots off.
I would really like somebody to help me out.
Note: I've tried to go into safe mode, but it doesn't want to boot up from that mode either.

ShadowofColosuss708,
you can try this: boot your MacBook Pro into Recovery mode by holding down a Command key and the R key as it starts up. Once the OS X Utilities menu appears, select Disk Utility. On the left-hand side of the Disk Utility window, select your internal disk’s boot partition (typically called “Macintosh HD”). On the right-hand side, press the Verify Disk button if it’s not greyed out; if it is greyed out, or if it reports that errors were found, press the Repair Disk button. Once the verification/repair is completed, exit Disk Utility and select Restart from the Apple menu to restart in normal mode. Does it reach the login screen now?

MacBook Pro stuck on boot screen

Hello, I have recently turned on my 2010 MacBook Pro to find that it stays on the white boot screen with the little wheel spinning :( I have no discs or anything to restore my computer back to. What can I do?

First see if you can boot into your Recovery partition by holding down the command and R keys whilst booting. If you can get there use Disk Utility to Verify and, if needed, repair you hard drive. If the drive can't be repaired, you'll need a new one.
Clinton

Macbook pro won't boot, stuck on white apple screen

Noticed today, that my macbook pro won't boot . It gets to the white apple screen with the spinner under the apple logo. It stays like this for a long time without doing anything except spinning.
I've powered down and tried to boot up several times.
I have boot camp and windows on my mac and when the white screen appears, I can press Option to bring up which hard drive and the Windows partition will load without any problems.

Exacty what happens when you try to boot up from the disc that came with your computer? Are you holding down the c key? Have you tried holding down the "option key?" Are you able to run the Hardware Test - Intel-based Macs: Using Apple Hardware Test
Shut down your computer and disconnect all peripherals (keyboard & mouse if pertinent) from your computer. Now reboot.
If the Mac starts up normally, shut it down again and then plug in one of the peripherals (keyboard or mouse first) and start up your computer again. If it does so successfully repeat the process, adding one peripheral at a time until your Mac acts up. At that point, disconnect the last peripheral you added, reboot your Mac and search the peripheral vendor's website for an updated driver.
If no driver exists or the problem remain after installing the new driver, try a different cable or a different port on your Mac.
If none of the above works, again disconnect all peripherals from your Mac, hold down the "shift" key to start up in "Safe Boot" mode.
If the Mac starts up correctly, restart without pressing the "shift" key.
If your computer still does not start up properly, shut it down and restart it while holding down the Apple+Option-P-R keys; keep holding "all 4 keys" down until you hear the startup sound "twice."
If none of the above work Disconnect all peripherals from your computer. Boot from your install disc & run Repair Disk from the utility menu. To use the Install Mac OS X disc, insert the disc, and restart your computer while holding down the C key as it starts up.
Select your language.
Once on the desktop, select Utility in the menu bar.
Select Disk Utility.
Select the disk or volume in the list of disks and volumes, and then click First Aid.
Click Repair Disk.
(If Disk Utility cannot repair, you will need a stronger utility (3rd party) - Diskwarrior or Techtool PRO)
Restart your computer when done.
Repair permissions after you reach the desktop-http://docs.info.apple.com/article.html?artnum=25751 and restart your computer.
Remove any 3rd party ram.
Reinstall Lion - This will install a "fresh" copy of Lion without archiving old system files but leaves the rest of your files in place.
If your computer is still under warranty or you have Apple Care, take full advantage of it by letting tech support deal with your problems. It's what you're paying them for.
Out of warranty - take the computer to an Apple store or an AASP. Whichever is more convenient for you.

Macbook Pro Will Not Boot Windows Disk

I have a late 08 (or early 09) Unibody Macbook Pro 2.53Ghz. I start the Bootcamp Assistant and successfully create my Windows partition. When I restart with the Windows 7 disk, I get a blinking cursor for 1 second then it goes to a black screen and never leaves. I have tried several different Windows 7 disks with the same result. I have even tried booting from a Windows Vista, Windows XP and even a Ubuntu disk all with the same result, stuck at a black screen.
I took the hard drive out of this mac and put it into my wife's older Macbook pro, and it booted off the Windows 7 disk and completed the install to the drive with no issues. I then put the hard drive back into my Macbook Pro and get the same black screen when trying to start the Windows partition, and still have the same problem that it will not boot from any other OS disk be it Windows or Ubuntu. It boots from OS X DVDs without a problem.
Also several months ago I had a Windows XP installation on this computer with no issues. I wiped it just before going to Snow Leopard.
Any clue as to what is going on here?

What is really odd is if I take my hard drive out of my Unibody Macbook Pro and put it into my wife's non-unibody Macbook Pro, it boots the Windows partition with no problem (Remembering I previously swapped these hard drives to complete the Windows installation to my hard drive). Seeing as the disk boots on her machine fine and not in mine, and my Windows cds (DVDs) boot fine on hers and not on mine, it seems to me it's something specific about my machine, but I can't imagine what it is.

Mid 2006 Macbook Pro won't boot (from HD or optical)

My mid 2006 Macbook Pro will not boot from the hard disk, or from the internal DVD. I am currently running the latest version of Lion (10.7).
I tried searching the forums and found a similar issue here:
https://discussions.apple.com/thread/1687899?start=0&tstart=0
But that was with a Mac Mini. And it doesn't look like the OP issue was ever resolved. I am having the exact same problem.
When attempting a normal boot from the internal HD of the Macbook Pro. It will make the happy chime of a successful POST. It will display the Apple logo. And that's as far as she gets.
No spinning wheel, no error image, no nothing. Eventually the system will start spinning up the fans as if it were under load (this was after about a half hour of just letting it sit there).
Doing a verbose boot, it never went past this:
com.apple.driver.Apple.IntelCPUPowerManagement
Photo of verbose boot:
Here's what I've tried.
1. Bought a brand new battery (as the current one was at death's door)
2. Zapped PRAM (Apple + Option + P + R)
3. Reset SMC according to these directions: http://support.apple.com/kb/HT3964?viewlocale=en_US
4. Attempted to boot to my original Tiger (10.4) install DVD, only to stop at this point during a verbose boot (Apple V):
Extension "com.apple.driver.AppleACPIPlatform" has immediate dependencies on both com.apple.kernel and com.apple.kpi components; use only one style
Photos:
5. I am able to put her in Target Disk Mode (hold T at boot). Then with a firewire cable I can connect it to my wife's Macbook 13" and I am able to run disk utility on it! Disk Utility did find and repair errors, however, it still refuses to boot.
6. I attempted to boot from my wife's Macbook 13" in Target Disk Mode. I put her machine in Target disk mode. Connected the firewire cable. Powered on my 15" MBP while holding the option key. Then I selected her drive as the boot disk... however it still refuses to boot even from a known working HD.
7. Finally, I swapped around RAM DIMMs with no change in behavior.
Help! I know she's an older gal (Laptop is 6 years old now) but I'm not exactly flush with cash and would rather not give up on her just yet.

My Mac started freezing (colored pinwheel) every time I tried using any application (i.e. Safari, iPhoto). After restarting for the 2nd time, it would no longer boot - makes start up sound but gets stuck on gray screen w/ apple icon. I tried resetting PRAM also - did nothing. I decided to reinstall OS; problem now is my HD is nowhere to be found! I am a tech dummy so this is way beyond my comprehension...I'm not seeing my HD from the Disk Utility either???
Side question...I backed up my files (mostly pics JPEG and videos) on DVD (had to compress to save). Why can't I open files on PC?

Macbook Pro won't boot into safe mode or via bootable USB key

Hi,
Am running OSX Lion latest version on my Macbook Pro 4,1 and can't get the thing to boot from any source. Always get's stuck at the grey screen with apple logo. Have tried all the following...
- Straight Boot (power on)
- Boot via Recovery HD (hold option on bootup then select)
- Boot via Safe Mode (Holding Shift on bootup)
- Boot via Safe Mode Verbose (Shift, Command, V)
- Boot via bootable Lion USB Key (Hold option, and choose the USB drive - not the same USB key works on my other macbook pro)
On every one (except verbose) it just get's stuck on the grey screen with spinning timer thingie.
I have done PVRAM reset, SMC reset and have reseated the RAM and all to no avail. I'm pretty sure the problem was caused by removing battery at wrong time (device not responding after sleep mode started and I plugged in power - should have been more patient!)
I have a Time Machine backup but it's a bit older than I thought and very much want to get my newer photos off it before rebuilding - not that Time Machine would work in current state anyway.
So what are my remaining options? Will I have to open it up and remove the HD as next step or is there anything else left to try? Can I remove the HD and connect it via a USB caddy to my existing Mac to recover info (hardrive spins and sounds ok to me)?
Any advice appreciated...

ds store wrote:
Yes, once the data is off you can use Disk Utility to Erase the entire drive (Lion + Recovery) with the Zero option (one selection below 7x) then use the Lion USB to install it fresh and stick it back into the machine.
Thanks for the info - I removed the HD and data is all ok on there so very happy about that. Before I wipe the data (all backed up now) I thought I would try booting the mac without any harddrive installed - using a OSX Lion bootable USB. However, still can't get past the grey apple screen and circle icon whirling away. I know the USB works ok, as tried it in my 2011 Macbook Pro and it boots absolutely fine.
I am happy to wipe the HD now and start again, but seeing as the DVD Drive is broken I'll probably need a USB drive boot to install OSX onto the wiped HD anyway. I'm a bit lost as to what to try now.

Macbook pro won't boot - how do I retrieve emails?

Hey guys
I've got a common problem that my Macbook pro won't boot. Sometimes I get stuck on the grey screen with spinning wheel, sometimes on the blue screen with spinning wheel
I've scoured the internet on another machine and tried every trick I can find with the MacBook Pro including
Disk / Permissions repair from install disk (says the HD is fine)
PRAM
Single User
Soft
It seems like my only option at the moment is an Install and Archive. I can mount the MacBook Pro on another machine with a firewire and remove files and backed up a lot on a hard drive before it died
What I am worried about is how to retrieve some emails from the machine that only exist locally because I have deleted them from the server
Is there a way of doing that?
Would Migration Assistant work?
If anyone could help me with this or suggest any other methods for bring my machine out of a coma I'd really appreciate it
d

Try a different adapter. If you don't have access to a known-good adapter any other way, make a Genius Bar appointment at an Apple Store.

Macbook pro stuck on apple

macbook pro stuck on apple

Reinstall OS X without erasing the drive
Do the following:
1. Repair the Hard Drive and Permissions
Boot from your Snow Leopard Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer.
If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
2. Reinstall Snow Leopard
If the drive is OK then quit DU and return to the installer. Proceed with reinstalling OS X. Note that the Snow Leopard installer will not erase your drive or disturb your files. After installing a fresh copy of OS X the installer will move your Home folder, third-party applications, support items, and network preferences into the newly installed system.
Download and install the Mac OS X 10.6.8 Update Combo v1.1.

My Mid 2010 MacBook Pro will not boot

My Mid 2010 MacBook Pro will not boot regularly, in safe mode, in recovery mode or from original OS DVD. Is this the logic board?
I've tried resetting the SMC and pram numerous times and even tried switching out hdd's to try and do a clean install on a new hdd.
If I attempt to boot regularly or from recovery drive the grey apple logo appears for a period before the screen goes black and the power LED operates as though in 'sleep' mode. I'm unable to wake it from this state and the same applies to booting in safe mode.
When attempting to boot from the OS DVD that was originally packed with the computer it just freezes on the language select option, this occurs with the other hdd's I have attempted to use.
Any other suggestions to get it working? I fear the logic board has gone and that the repair won't be worth the money.
Thank you in advance.

Hi JRC8.8,
It sounds like you have been on the right track in trying to troubleshoot this issue. You may want to see if your MacBook Pro will boot directly to the Apple Hardware Test, as outlined in the following article:
Apple Support: Using Apple Hardware Test
http://support.apple.com/kb/ht1509
Regards,
- Brenden

MacBook Pro will not boot up

Hello,
My three-month-old MacBook Pro refuses to boot up. The problem began about two days ago, and since then, the situation hasn't changed. When I press the power button, the Apple logo on the boot screen appears, but it quickly flashes on and off, with a "no symbol" and a symbol consisting of a folder with a question mark on it flashing at random concurrently. I really need my MacBook Pro to boot up, because I require it for homework that is due tomorrow. I have never dropped or even scratched this computer, and I always use it in a cool and dry environment, so I don't think it could have been anything to do with overheating. But I'm no expert. Does anyone know what I can do? Thank you so much, in advance!

Usually the flashing question mark means that the computer can't find a bootable device. Your hard drive may be damaged.
Try booting into your Recovery partition, holding down the command and R keys whilst booting. Use Disk Utiity to both verify ad repair your hard drive. If the drive cannot be repaired, called back (you can access Safari from the Recovery partition).
Clinton

Macbook Pro will not boot beyond grey screen. System freezes.

My Macbook Pro will not boot-up or get beyond the grey screen (with spinning gear wheel.) I've tried all the recommended actions: resetting PRAM, disk repair, permissions repair, re-boot in safe mode etc but still the problem persists. When viewing the safe-boot in verbose mode, the system seems to hang at the stage when it's checking the Airport & Ethernet - the last line on the page reads: "AppleBCOM5701Ethernet: 0 0 setFixedSpeed - logic error, speed any?"
Any ideas how to fix this without doing an Archive & Install?
I'm assuming that if I do an "Archive & Install" then I will lose all my Applications (VLC, Handbrake, MS Office for Mac etc.) Will this actually be the case? Will I lose them.
Any help gratefully received. Many thanks.

jfromplymouth wrote: ...I'm assuming that if I do an "Archive & Install" then I will lose all my Applications (VLC, Handbrake, MS Office for Mac etc.) Will this actually be the case? Will I lose them...
Archive and Install just affects the System files, so any apps you have should still be available afterwards. The Installer on the disk that came with your Mac, when you bought it, will tell you this before you proceed. Of course, you can always back out of the Installer if you feel chicken.
Notwithstanding it is still necessary to backup everything. You need to check that Time Machine is set to also backup your Applications folder. It might be set not to do this.
It may not be necessary to worry about this if you have the original installer disc(s). I think any stuff downloaded from iTunes etc can be re-downloaded. However, it's probably quicker to get Time Machine to backup your apps if you can afford the HDD space. It's bound to be quicker than re-downloading the stuff plus any updates. And of course there's those Apps that you have but forgotten about. What about them?

MacBook Pro won't boot up after interruption of update

I interrupted the installation for the OS X Mountain Lion v10.8.2 and now my MacBook Pro will not boot up. Any suggestions besides calling Apple support or going to the store?

Hi,
I am having the same problem with my Macbook Pro. Did you manage to find a solution to this problem?

MacBook Pro will not boot

MacBook Pro will not boot. Just get grey screen. When I hold down control + R, I get blank blue screen.

Which model MacBook Pro do you have?
It's COMMAND and R that will take you to your Recovery partion, not Control and R.
If a later model, can you boot into Internet Recovery (booting whilst holding down the command, option and R keys)?
Clinton

MacBook Pro will not boot after software update

MacBook Pro will not boot after doing an Apple Software Update (of course they will not help you). MONEY, MONEY, MONEY is the name of the game. They can cause your computer to crash and still charge you!
Does anyone have an answer to why my computer is showing a little gear spinning for hours? I have tried several things with NO luck.
Thanks-

Run through the list of fixes here
Step by Step to fix your Mac

Macbook pro stuck on boot

Similar Messages

Maybe you are looking for