Macbook pro trackpad too quick when in documents
In my MacBook Pro Retina, the trackpad works perfectly when browsing but it is toooo quick when in documents. as soon as I touch it and move my fingers few millimetres or even micrometers the document moves and stops miles away...
Anthony,
Have you learned anything more about this problem? I have the exact same issue. Headphones that work fine on an older Macbook Pro are deafening on the new (Mar. 2008) model.
I haven't had time to go down to an Apple store and see if it is the same on all machines.
Eric
Similar Messages
-
Macbook Pro way too loud when headphones plugged
Hi
I've always had this problem, when I plug in any type of headphones, I must lower the volume to one - max two - "blocs" of volume, otherwise my head explodes. I unplug them, and I have normal volume range with the external speakers.
Anyone has that problem too??
thanksAnthony,
Have you learned anything more about this problem? I have the exact same issue. Headphones that work fine on an older Macbook Pro are deafening on the new (Mar. 2008) model.
I haven't had time to go down to an Apple store and see if it is the same on all machines.
Eric -
So in the last few days I’ve noticed that pressing my volume change keys actually isn’t changing the volume on my macbook pro at all. When I press the volume up or down keys, it makes the recognisable pop sound but stays at the same volume while the squares go up or down. I mute it but my computer still makes sound. It’s the same with the volume control up the top of the screen, too. I slide it up and down and it doesn’t change the volume at all. The only way I can change the volume is with my speakers or the program I’m in (iTunes, VLC etc). I restarted and it seems to be okay then I go to change it a couple minutes later and it’s back to not working again.
I’ve checked my settings- the “use all F1, F2, etc. keys as standard fuction keys” is not switched on, and I have tried a suggestion of moving the com.apple.systempreferences.plist file out of the library and onto the desktop and restarting and neither of those seem to make any difference whatsoever. I’ve tried to find online forums but the only suggestions I found were those two and they didn’t work.
I’m just annoyed because I usually have the worst luck with technology but my macbook had been going strong and I got it because of the apparent lack of things that could go wrong, but of course even if there is one thing that could go wrong it will happen to me.
Please help!You migh give resetting your NVRAM a try:
http://support.apple.com/kb/ht1379 -
MacBook Pro trackpad constantly clicking
I have a late 2008 Macbook Pro 5,1 15' 2.53 GHZ-4GB Ram. Running Mac OS X Lion 10.7.4 (11E53)
My Macbook Pro trackpad is stuck constantly left clicking
some right clicking
moving around by itself
not always responding completely to touch.
In text boxes when typing it constantly erases text
Pretty much unusable when this is happening.
It will happen as long as it wants to and start working normally again with no rhyme or reason I do not see anything in particular that seems to trigger it.I did not just start this thread without searching the net and here. I am just looking for some opinions on if I should take it in for repair or if there are any other things I can try that I may have missed.
Here is a list of what I have tried so far.
Reset PRAM and NVRAM.
Checked battery for bloating (even though that would not cause this problem would only cause it to stick had to replace once already).
Booted into safe mode (logged into seperate admin account I never use problem started again in safe mode after about 30 seconds of using trackpad).
checked trackpad screw (was fine but tried loosening it and tightening slightly to see if it helps.
Turn off, Remove battery, hold power for 5 seconds, replace battery and boot.
Using external mouse exhibits the same behavior (tried both USB and different wireless mice) This makes this problem seem more likely software not hardware
One thing I have not tried is deleteing the plist files for the trackpad I read that fix somewhere although I can not find the link now. If and when it decides to stop again I will try that next. I am A+ certified not ACMT but I can replace anything on it if needed so please mention anything you can think of even hardware. I would rather not restore the OS as I have about 300GB of data and transferring it to one of my servers or external drive would be a pain, time consuming, and I have read it does not solve these types of issues.
Please help
Sincerely,
Frustrated but still happy Apple user.Well after some further investigation it seems I may have had some malware. I receive a lot of packages and this one seem to have slipped by my spam filter. It's called Mal/JSRedir-J of course I also forgot to re install Sophos Antivirus after I did some software development work and was running strictly through my citrix server which is very secure. *Slaps self in face*.
I am running a thorough scan now but that trojan popped up. I was able to install Sophos after a reboot before it started acting up barely got my password in on install before cursor started flying around the screen.
So far so good. Hopefully it stays that way, and maybe this will help someone else. Virus is not always the first thing to come to mind when I think MAC, and this is my first infection in 4 years -
I downloaded Piezo to my iMac about a month ago. Now I can't download it to my laptop even though I have authorized the MacBook Pro in iTunes. When I open the App Store, the Piezo app indicates that I have to pay. How do I download Piezo to my laptop, which I am entitled to do?
I'm running Snow Leopard on my iMac. I have a heap of documents that were created using an old word processor application called Apple Works and it wont work on Lion or Mt Lion. So I'm stuck with Snow leopard for the moment. I guess I can't use the new iPhoto either then...
-
Subsequent to Yosemite or updates, my repeating calendar events can not be updated as before. When I update an event (of a repeating event) on my MacBook Pro; its reverts back when I shut it down and come back, and doesn't update other devices?
Has anyone experienced this and does anyone know a fix?This is incredibly frustrating for me too!
I have a repeated monthly event for a discount at a store that is offered on the first Tuesday of every month. So I have a repeated event taking place on the 1st of every month. In the previous month I reset next month's date from the 1st to whatever date falls on the first Tuesday.
But ever since upgrading to Yosemite, I am experiencing the same problem as the original person who posted. The date saves on my calendar but does not sync to my iCloud. When I reboot the computer, the date reverts back to the 1st.
I'm thankful I don't have any events that needed to be tracked because ALL of my previous changes in the past have reverted back to the 1st of the month. I would have been in the same terrible situation as yaz999 in having to manually change every event in previous months.
Why hasn't this bug been fixed yet???!!! -
tried to reinstall OSX Mountain Lion 10.8.4 and every time i start with the installation i get a requested time out message, had to shut down my MacBook Pro retina. Now when i start up it automatically start internet recovery for two ouers. After the internet recovery the same problem with reinstalling OSX message
Gave up on the GUI. This script derived from http://blog.netnerds.net/2012/07/os-x-how-to-setup-nat-on-lion-and-mountain-lion / seems to work for me:
gwdev=en0 # This is my WiFi connection (has Internet connection)
targetdev=en1 # This is the USB to Ethernet adapter (to give Internet connection)
/sbin/ifconfig $targetdev down
/sbin/ifconfig bridge0 create
/sbin/ifconfig bridge0 up
/sbin/ifconfig bridge0 addm $gwdev
/sbin/ifconfig bridge0 $HOST_ADDR
/sbin/route add default -interface bridge0 -ifscope bridge0 -cloning
/usr/sbin/sysctl -w net.inet.ip.forwarding=1
/sbin/ipfw add 100 divert natd ip from any to any via $gwdev
/usr/sbin/natd -interface $gwdev -use_sockets -same_ports -unregistered_only -dynamic -clamp_mss -enable_natportmap -natportmap_interface $targetdev -
MacBook Pro doesnt start. When I start my lap top, it shows the apple and the line uploading but it only goes like to 1/3 and then it goes blank for some seconds, then it turns off by itself and turn on again and happen the same, apple logo, line .. the noise like-fan going on, then turn off and turn on again. Tried starting holding option command P and R key and didnt work either. Starting to think I have lost all my data inside
Try a SMC reset.
http://support.apple.com/kb/ht3964
It might be helpful if you indicated the exact model/year of your MBP. Are you running Lion OSX?
Ciao. -
My macbook pro shuts down unexpectedly when battery gets to 20% and is not plugged in
Why does my macbook pro keep shutting down when it gets to 20% without warning?
here is my battery information:
Battery Information:
Model Information:
Serial Number: SMP-ASMB014-3774-64a
Manufacturer: SMP
Device name: ASMB014
Pack Lot Code: 0002
PCB Lot Code: 0000
Firmware Version: 0110
Hardware Revision: 0500
Cell Revision: 0102
Charge Information:
Charge remaining (mAh): 3395
Fully charged: No
Charging: No
Full charge capacity (mAh): 3677
Health Information:
Cycle count: 1148
Condition: Fair
Battery Installed: Yes
Amperage (mA): 385
Voltage (mV): 12442
System Power Settings:
AC Power:
System Sleep Timer (Minutes): 10
Disk Sleep Timer (Minutes): 10
Display Sleep Timer (Minutes): 5
Automatic Restart On Power Loss: No
Wake On AC Change: No
Wake On Clamshell Open: Yes
Wake On LAN: Yes
Display Sleep Uses Dim: Yes
Battery Power:
System Sleep Timer (Minutes): 10
Disk Sleep Timer (Minutes): 10
Display Sleep Timer (Minutes): 2
Wake On AC Change: No
Wake On Clamshell Open: Yes
Display Sleep Uses Dim: Yes
Reduce Brightness: Yes
Hardware Configuration:
UPS Installed: No
AC Charger Information:
Connected: Yes
Charging: No
WHAT DOES IT ALL MEAN??That many cycles is amazing service. A battery that consistently shuts down at about the same charge level percentage every time probably has a bad cell (that info came form an Apple technician) and needs to be replaced.
It's given you far longer service than many of us get, and may be a new record around here for cycle count! -
My MacBook Pro keeps making copies of a document that I am trying to save. I don't want to duplicate the file. I only want to save it on both my hard drive and my external hard drive. I do not want to change its name for every save, which the computer seems insistent on doing. Help!!
11lizzyp wrote:
can't be saved because the file is read-only.
I did not create the file to be read-only. I created to be able to continue to add to it as I work on it.
More on versions here:
http://support.apple.com/kb/ht4753
local snapshots:
http://support.apple.com/kb/HT4878
Sounds like a permissions problem ie read only.
If running repair permissions from your DiskUtility.app does not sort it,
Someone should jump in here with erudite and concise fix. -
What's wrong with my macbook pro (15" early 2011) when i connect it with TV via hdmi
What's wrong with my macbook pro (15" early 2011) when i connect it with TV via hdmi
Hello Alex,
It sounds like you are getting excessive CPU usage when connecting an external display via HDMI to your computer. I would try the troubleshooting steps outlined in the article named:
Apple computers: Troubleshooting issues with video on internal or external displays
http://support.apple.com/kb/ht1573
When using an external display be sure to check the following:
If you're using an Apple notebook, confirm the AC power cable or adapter is securely connected to the computer and the cable providing power to the display is also secure. It is always good to have your notebook connected to AC power when an external display is in use.
Confirm display adapters are fully seated in their respective connections and that they are supported models and for the computer and display. Refer to these articles to assist you with adapter compatibility and further configuration information:
Monitor and Display Adapter Table
About Mini DisplayPort to HDMI adapters
Apple Mini DisplayPort adapters: Frequently asked questions (FAQ)
Thunderbolt ports and displays: Frequently asked questions (FAQ)
Remove all display cable extenders, KVM switches, or other like devices and retest to determine if the issue is resolved.
Try unplugging the video adapter or cable and then plug it back in.
If more than one video adapter is in use (or "daisy-chained"), troubleshoot by using only one adapter.
Example: A mini DisplayPort to DVI adapter connected to a DVI to HDMI adapter is an unsupported configuration because there is a series of adapters in use.
If available, try using a different display and or adapter (or use a different connector by using DVI instead of VGA, for instance).
Reset the systemYou can reset the Mac's parameter RAM and SMC.Reset the resolutionStart by resetting the Mac's parameter RAM. If the display does not come up, was previously set to an unsupported resolution, and still results in no video:
Start up in Safe Mode.
From the Apple () menu, choose System Preferences.
Choose Displays from the View menu to open the preferences pane.
Select any resolution and refresh rate that your display supports.
Restart your computer.
Thank you for using Apple Support Communities.
Cheers,
Sterling -
How do I FTP files from a security camera to iCloud so they can be retrieved back to my MacBook Pro whenever I connect when travelling?
RussDo you want to watch the live feed of your secutiry cameras or recorded footage?
In either case, I don't think iCloud is your solution.
For the first one, check with your security camera software, they usually have this option of broadcasting, so you'll know how to access it.
For the later, you should use something like Dropbox (www.dropbox.com), since iCloud file sharing is, up to this date, app restricted.
Hope it helps.
JP -
Why does my macbook pro "goes to sleep" when charging?
Why does my macbook pro "goes to sleep" when charging? It is working fine without charging but once I attach the charger to my laptop, it just blacks out or goes to sleep mode and I can't wake it up unless I unpluck the charger.
I read from threads that it is a logic board problem....How do I solve this problem?Try an SMC reset. Follow the method for "a battery you should not remove yourself."
http://support.apple.com/kb/ht3964 -
I have a license for CS6 on my MacBook Pro. I want to purchase an iMAC and be able to do my heavy duty Photoshop processing on this new iMAC when I am at home I need to keep CS6 on my MacBook Pro and use it when I travel. How can I have copies of CS6 on both machines. I am the only user of this software.
You can install and activate CS6 on both machines perfectly legally.
-
MacBook Pro goes to sleep when copying files from attached drives
I have noticed that since installing Yosemite my MacBook Pro goes to sleep when it is in the middle of copying a large number of files. When I wake it up the copying continues.
I have also noticed that when I am watching videos from my shared iTunes library on an Apple TV the video will stop after about 15 minutes and the connection to the library is lost because the MacBook Pro has gone to sleep. When woken up then access to the library is restored but I need to reselect the movie and then resume.
I have changed the power saving options to do not let drives sleep when idle and do not sleep laptop.
Anyone else have any experience of this or better still a fix.
Thanks in advance.I have just found that if I turn off the display sleep in the power settings then the problem is resolved. It means though that the screen on my MacBook Pro is on all the time albeit with a screen saver.
Maybe you are looking for
-
How can I install iWork '09 on new MacBook with Lion?
I have an install DVD for iWork '09 (9.0.3), and I've been running iWork on my iMac for several years without a problem, even after upgrading to Lion. Now I have a new MacBook Air with Lion preloaded and am trying to install iWork on the new machine.
-
Is there a fix yet for the no sound problem with lion on the iMac without having to restart every time I switch the computer on?
-
CS4 crashing/quitting during PDF Export
Hello, I am having an issue exporting a 108 page document to PDF. The document itself is only 25mb and the links maybe 50mb but everytime it nears completion InDesign abruptly closes... I have seen the suggestion of printing to Adobe PDF and when I d
-
How can I change Frame.Knob size?
I have CNiKnob control on my dialog. Style of this knob is like a speedometer. There are small sub-knob in center of this control(Pointers begins from it). It named Frame.Knob in Images tab of Properties. I need to set a custom size to this sub-knob,
-
Hi, I'm trying to deploy an application but it doesn't start up properly. There is a queue destination resource - jms/liferay/MailQueue with property imqDestinationName=MailDestination and I have created the physical destination MailDestination. My s