Macbook pro turns it self off, wont charge battery, often wont boot.

Around June, after a couple months of light issues, my macbook pro basically just stopped turning on. I initially thought it was the video card, and since it was one of the earlier core 2 duo models, didnt think it was worth fixing. Just recently I happened to get the torx screwdriver needed to fully open the computer, and after not trying it for a couple of months, it booted up like new. At this time the battery appeared to be charging normally, but again something happened that seemed to coincide with my plugging a usb mouse into the usb port near the magsafe adapter, the light flickered and then it ceased charging. A little while later I was trying to move files off, and it shuts itself off. Then the same problem comes up while trying to boot it, typical noise, and then the apple screen comes up, and the picture is flickering and dims til its off again.
Since then the computer can be used for periods, seemingly doing better after its left off for hours at a time, but only for 30min-1hr max. the battery appears to not be charging at all, and the magsafe light, is either a bright green, or a dim green that has flickers between green and orange. If i press the button on the battery, no lights show up on it at all, and whenever the computer is actually on the batt. monitor says 0%.
The adapter, is in pretty good shape since I replaced it a 18mo ago, so I dont think thats the cause, the battery itself had very little life when it was running before dying in june, but Im not sure how a defective/dead battery could cause any of the other problems. I tried to reset the settings by removing adapter+batt. and holding power for 5 sec, but i dont see any effect.
Im clueless about troubleshooting macbook pros and laptops in general, though i would honestly think that the issue is basically due to the laptop not being able to be powered correctly, but after that I am lost.
any help would be greatly appreciated.

Hi W, and welcome to Apple Discussions.
Try removing the battery and booting.

Similar Messages

  • Does the battery charging in the macbook pro retina automatically cut off when the battery is fully charged?

    Does the battery charging in the macbook pro retina automatically cut off when the battery is fully charged? or does it continue charging?In which case,is it better for the battery life to switch off the power supply or leave it on while using the macbook?

    Yes, and the pilot light on the MagSafe2 connector changes from orange to green. If you unplug, you will start draining the battery again, whereas if plugged the Mac will take power from the brick and leave the battery in a charged state.

  • My i phone 3g turns it self off when the battery power gets to about 50 % is there a few for this?

    My i phone 3g turns it self off when the battery power gets to about 50% is there a fix for this

    This is often due to faulty battery. Make Genius reservation and take iPhone to Apple Store for free quick battery diagnostic testing.

  • MacBook Pro shuts down and won't charge, battery light on the side is off completely?

    Hey guys,
    So about 20 minutes ago, I walked over to my macbook pro ('17) to plug in my phone charger. The top was already open, so I didn't have to pull it up. I clicked the touchpad to turn it on, and it turned on for literally half a second, and turned black with a bit of a static noise I believe. As if it blew a fuse.
    So I look on the side of the computer where you can press that little button and a bunch of lights will turn on according to battery life, and nothing. Not one light turned on. I got this computer fixed a month ago with a replaced battery, screen, graphics card I believe, and operating system.
    What happened?? It won't charge or turn on. Is there any chance I can revive this or is it toast?

    Hi, I am having the same exact problem! Anyone who know what to do?

  • Why does my macbook pro keep shutting down with a charged battery

    Why does my Mac book pro keep shutting down? I lose everything I am working on when it shuts down  help

    kva,
    which model MacBook Pro do you have? Is it running Mac OS X 10.5.5? If not, which version of OS X is currently installed on it?
    Are you running on battery when it shuts down, or are you running on AC when it shuts down, or does it happen in either case? Which app are you working in when it shuts down? Does it happen only in that app, or does it happen no matter which app you’re working in?

  • When we are watching something on Apple TV and our Macbook Pro turns on or off the Apple TV goes back to the menu and stops whatever is currently playing.  Any idea how to stop this?

    Any ideas?

    Thanks, but there has to be someway through ITunes or something to make this not happen.  It used to not do this so something with an update or something must have changed a setting somewhere.  Anyone else have any ideas?

  • MacBook Pro 15' 2.8GHz 2009 not charging battery.

    Hi there!
    This problem just came out of no where!
    My battery doesn't charge anymore. Also the date gets back to 2001 every time the MBP powers up.
    I tried to re set the SMC and nothing happened. After released all keys and power the MBP the Magsafe didn't change colour as described.
    Another note: the instructions don't say the time that you actually have to hold the keys down for?
    How long do you have to wait before powering up your MBP etc. Nt very specific.
    Anyway, The battery information says that Battery is "Not Charging" on the System Profiler and the drop down menu on the top right battery icon. My MBP is still under warranty but I don't usually panic before go to the Mac Shop and get help. "It takes a long time to get help by a genius in Melbourne, even if you book a time" Poor guys they don't stop.
    I cleaned all the surfaces of the Magsafe and MBP and I also have a second MBP and used the other Magsafe with the same issue.
    On the System Profiler info the battery seems to be Ok with just one cycle.
    Any help will be very appreciated.
    Cheers

    The other way around is the same. I tried "detect display", nothing happens. Nothing showing another display at all.
    If it was a defective cable then I would NOT get a replacement because I just don't want the hassle of working on it and the problem will be the same.
    Most likely to mail it back to get cash back.
    Umm, to add, I am running 10.6.4 and have NOT yet upgrade it to 10.6.5. I still don't think that'll solve the problem.
    Any ideas?

  • MacBook Pro turned off on its own and now won't turn back on.

    MacBook Pro turned off on its own and now won't turn back on.  Battery had 41% just before this happened and green indicator on power cord is showing, so it seems like it's charging.  What should I do?

    The led on the power adapter should be amber if it is charging.  Green just indicates that it is supplying power to the MBP.
    Try a SMC reset:
    http://support.apple.com/kb/ht3964
    Ciao.

  • Macbook pro turns on for a minute and turns off before it fully loads

    The MacBook Pro turns son for about 30 seconds before turning off again even though it is charged.

    Is the power adapter attached? 
    Have you tried a Safe boot?
    http://support.apple.com/kb/HT1455
    If that fails, I suggest an appointment at an Apple store genius bar.
    Ciao.

  • MacBook Pro turns off when mega-safe adapter is removed

    Hello,
    I just installed a new battery, however, battey health condition seems normal but my macbook pro turns off whenever  i remove the mega-safe adapter. I also noticed that even though the battery says 100% charged, the fully-charged green indicator does not come on. Below is the system information.
    HELP!!!
    Battery Information:
      Model Information:
      Serial Number:    W0*****3LC
      Manufacturer:    SMP
      Device Name:    bq20z451
      Pack Lot Code:    0
      PCB Lot Code:    0
      Firmware Version:    201
      Hardware Revision:    000a
      Cell Revision:    165
      Charge Information:
      Charge Remaining (mAh):    5568
      Fully Charged:    Yes
      Charging:    No
      Full Charge Capacity (mAh):    5568
      Health Information:
      Cycle Count:    3
      Condition:    Normal
      Battery Installed:    Yes
      Amperage (mA):    8
      Voltage (mV):    12580
    System Power Settings:
      AC Power:
      System Sleep Timer (Minutes):    10
      Disk Sleep Timer (Minutes):    10
      Display Sleep Timer (Minutes):    10
      Wake on AC Change:    No
      Wake on Clamshell Open:    Yes
      Wake on LAN:    Yes
      AutoPowerOff Delay:    14400
      AutoPowerOff Enabled:    1
      Current Power Source:    Yes
      Display Sleep Uses Dim:    Yes
      PrioritizeNetworkReachabilityOverSleep:    0
      Standby Delay:    4200
      Standby Enabled:    0
      Battery Power:
      System Sleep Timer (Minutes):    15
      Disk Sleep Timer (Minutes):    10
      Display Sleep Timer (Minutes):    15
      Wake on AC Change:    No
      Wake on Clamshell Open:    Yes
      AutoPowerOff Delay:    14400
      AutoPowerOff Enabled:    1
      Display Sleep Uses Dim:    Yes
      Reduce Brightness:    Yes
      Standby Delay:    4200
      Standby Enabled:    0
    Hardware Configuration:
      UPS Installed:    No
    AC Charger Information:
      Connected:    Yes
      ID:    0x0100
      Wattage (W):    60
      Revision:    0x0000
      Family:    0x00ba
      Serial Number:    0x00eee1de
      Charging:    No
    <Edited by Host>

    olacurrency wrote:
    error code: 4SNS/40000000: IPBR-9.165
    This is a current sensor on the power bus. This seems consistent with your symptoms.
    A faulty sensor on the logic board means  the board has to be replaced,  take in for repair:
    Genius reservation http://www.apple.com/retail/geniusbar/
    on-line https://getsupport.apple.com/GetproductgroupList.action
    check warranty https://selfsolve.apple.com/agreementWarrantyDynamic.do

  • Macbook pro turns off at 60% battery

    Whenever my laptop gets to 60%, my macbook pro turns off. I've read that resetting the smc might be able to fix it but it hasn't made much difference. Here's my battery info. Any help would be great. Thanks!
    Battery Information:
      Model Information:
      Serial Number:          9G12109CVD3MA
      Manufacturer:          DP
      Device Name:          bq20z451
      Pack Lot Code:          0
      PCB Lot Code:          0
      Firmware Version:          201
      Hardware Revision:          2
      Cell Revision:          158
      Charge Information:
      Charge Remaining (mAh):          1670
      Fully Charged:          No
      Charging:          Yes
      Full Charge Capacity (mAh):          2474
      Health Information:
      Cycle Count:          905
      Condition:          Service Battery
      Battery Installed:          Yes
      Amperage (mA):          734
      Voltage (mV):          12136
    System Power Settings:
      AC Power:
      System Sleep Timer (Minutes):          10
      Disk Sleep Timer (Minutes):          10
      Display Sleep Timer (Minutes):          10
      Wake on AC Change:          No
      Wake on Clamshell Open:          Yes
      Wake on LAN:          Yes
      Current Power Source:          Yes
      Display Sleep Uses Dim:          Yes
      PrioritizeNetworkReachabilityOverSleep:          0
      Standby Delay:          4200
      Standby Enabled:          0
      Battery Power:
      System Sleep Timer (Minutes):          10
      Disk Sleep Timer (Minutes):          10
      Display Sleep Timer (Minutes):          2
      Wake on AC Change:          No
      Wake on Clamshell Open:          Yes
      Display Sleep Uses Dim:          Yes
      Reduce Brightness:          Yes
      Standby Delay:          4200
      Standby Enabled:          0
    Hardware Configuration:
      UPS Installed:          No
    AC Charger Information:
      Connected:          Yes
      ID:          0x0100
      Wattage (W):          60
      Revision:          0x0000
      Family:          0x00ba
      Serial Number:          0x0031846b
      Charging:          Yes

    The Cycle Count is 905 so it may be time for a new  battery. Maximum is 1000.
    Check here >  Mac notebooks: Determining battery cycle count

  • Macbook pro turns off when i unpliug

    macbook pro turns off when i unpliug

    You either need to plug in your charger and if that isn't working if your machine is less than a year old take it in to your nearst Apple Store and let them deal with it. Or if you are out of warrantee you will need to get a new battery for your Mac
    Cheers
    Don

  • Hi my iphone was fully charged and turned its self off, i have tried to turn it back on and reset it, but no luck so i have plugged it in to my pc and it displays the apple logo and then goes back off i have tried this a number of times with no success

    hi my iphone was fully charged and turned its self off, i have tried to turn it back on and reset it, but no luck so i have plugged it in to my pc and it displays the apple logo and then goes back off i have tried this a number of times with no success anyone got any idears?

    Try here:
    iOS: Not responding or does not turn on

  • MacBook Pro turns on but will not load. Battery will power up and charge. The PRAM second start up seems to work, but the Apple timer continues add-infinitum. There is also a disc in the laptop so I can't load re-load software OS 10.6.1. How do I resolv

    MacBook Pro turns on but will not load. Battery will power up and charge. The PRAM second start up seems to work, but the Apple timer continues add-infinitum. There is also a disc in the laptop so I can't load re-load software OS 10.6.1. How do I resolve this problem?

    Try booting in Safe Mode by holding your Shift key down when booting. Also, try holding the eject key down when booting to eject the DVD. If you plug a mouse in and hold the clicker down when booting, that should eject the DVD.   
    17" 2.2GHz i7 Quad-Core MacBook Pro  8G RAM  750G HD + OCZ Vertex 3 SSD Boot HD 
    Got problems with your Apple iDevice-like iPhone, iPad or iPod touch? Try Troubleshooting 101

  • My phone turned its self off for about 10 minutes, when it came back on it went from 84% to 18%. When I put in on the charger it shows the plug symbol as if its fully charged but the phone stays at 18%, and now it won't turn on.

    My phone turned its self off for about 10 minutes, when it came back on it went from 84% to 18%. When I put in on the charger it shows the plug symbol as if its fully charged but the phone stays at 18%. Over time the battery dropped, but it went from 18, to 9, 3, then 1, and every time I put it on the charger it doesn't actually charge. Now my phone is off and it will not turn on.

    I'd suggest taking it to apple. Warranty or no warranty.

Maybe you are looking for

  • EJB 3.0: java.io.IOException: Unable to find session object ...

    Hello, We have an EJB3 application deployed to an Oracle AS 10.1.3.1.0 instance. Our main point of entry to the application is a stateful session bean (that controls access), that has injected several other stateful session beans. Like this: +@Statef

  • Problem in displaying XML document from database

    Hi I am getting only record in printing xml file which takes from data base. Here is my programme. Document doc; ����public void processTable(Connection con, String tableName) ����{ ��������try ��������{ ������������this.iColumnCount=0; ������������H

  • Dual G5 Powermac - CPU chirp/whine after 10.4 upgrade

    At home, I have a Dual G5 1.8 GHz Power Mac. At work, I use a Dual-G5 2.0 GHz power mac. With both of these machines, after upgrading to 10.4, I can hear the machine making high-pitched noises. The Dual-1.8 GHz machine `chirps', while the Dual-2.0 Gh

  • Updating my CS6

    I am trying to update my CS6 but I get an error message # U44M1I208, How can I fix this?

  • Iphoto database got disconnected during thumbnail rebuild; can't open

    iphoto will not access iphoto library. OS version is 10.5.8 and iphoto version is 7.1.5.  The iphoto library is on external drive. Today when opening iphoto, I was prompted to "Rebuild thumbnail for iphoto".  During that process, the external drive U